Novel sandwich structured glass fiber Cloth/Poly(ethylene oxide)-MXene composite electrolyte

Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performance all-solid-state lithium metal batteries.In this article,a novel sandwich structured solid-state PEO composite electrolyte is developed for high performance all-solid-state lithium metal batteries.The PEO-based composite electrolyte is fabricated by hot-pressing PEO,LiTFSI and Ti_(3)C_(2)T_(x) MXene nanosheets into glass fiber cloth(GFC).The as-prepared GFC@PEO-MXene electrolyte shows high mechanical properties,good electrochemical stability,and high lithium-ion migration number,which indicates an obvious synergistic effect from the microscale GFC and the nanoscale MXene.Such as,the GFC@PEO-1 wt%MXene electrolyte shows a high tensile strength of 43.43 MPa and an impressive Young's modulus of 496 MPa,which are increased by 1205%and 6048%over those of PEO.Meanwhile,the ionic conductivity of GFC@PEO-1 wt%MXene at 60℃ reaches 5.01×10^(-2) S m^(-1),which is increased by around 200%compared with that of GFC@PEO electrolyte.In addition,the Li/Li symmetric battery based on GFC@PEO-1 wt%MXene electrolyte shows an excellent cycling stability over 800 h(0.3 mA cm^(-2),0.3 mAh cm^(-2)),which is obviously longer than that based on PEO and GFC@PEO electrolytes due to the better compatibility of GFC@PEO-1 wt%MXene electrolyte with Li anode.Furthermore,the solid-state Li/LiFePO_(4) battery with GFC@PEO-1 wt%MXene as electrolyte demonstrates a high capacity of 110.2–166.1 mAh g^(-1) in a wide temperature range of 25–60C,and an excellent capacity retention rate.The developed sandwich structured GFC@PEO-1 wt%MXene electrolyte with the excellent overall performance is promising for next generation high performance all-solid-state lithium metal batteries.

A STUDY OF STRUCTURE AND PROPERTY CHANGES OF BIODEGRADABLE POLYGLYCOLIDE AND POLY(GLYCOLIDE-co-LACTIDE)FIBERS DURING PROCESSING AND IN VITRO DEGRADATION

Structure and properties of bioabsorbable polyglycolide (PGA) and poly(glycolide-co-lactide) (PGA-co-PLA)fibers were investigated during several industrial processing stages and in vitro degradation by means of wide-angle X-raydiffraction (WAXD), dynamic mechanical analysis (DMA) and mechanical property tests. In the orientation stage, the PGAfibers were found to have higher degrees of crystallinity than corresponding PGA-co-PLA samples produced under similarconditions. In the hot-stretching and post-annealing stages, after fibers were braided, PGA samples were found to gain morecrystallinity and higher T_g than PGA-co-PLA samples. The higher crystallinity in PGA fibers resulted in a slower rate ofdegradation. DMA results showed that a great deal of internal stress that was built during orientation and hot-stretchingstages was released in the post-annealing stage for a1l PGA and PGA-co-PLA samples. During earlier stages of in vitrodegradation, both PGA and PGA-co-PLA samples exhibited the typical cleavage-induced crystallization mechanism. Theheat shrinkage in the glass transition area was found to disappear after 6-8 days of degradation for all PGA and PGA-co-PLAsamples, indicating the amorphous portions of the polymers lost orientation after a short period in the buffer solution, mostlikely due to relaxation of the cleaved chains.

Wet-spun poly(ionic liquid)-graphene hybrid fibers for high performance all-solid-state flexible supercapacitors

It is crucial to develop flexible and wearable electronic devices that have attracted tremendous interest due to their merits on compactness,flexibility and high capacitive properties.Herein we report the continuously ordered macroscopic poly(ionic liquid)-graphene fibers by wet spinning method via liquid crystal assembly for supercapacitor application.The fabricated all-solid-state supercapacitors exhibited a high areal capacitance(268.2 mF cm 2)and volumetric capacitance(204.6 F cm 3)with an outstanding areal energy density(9.31μWh cm-2)and volumetric energy density(8.28 mWh cm-3).The fiber supercapacitors demonstrated exceptional cycle life for straight electrodes of about 10,000 cycles(94.2%capacitance retention)and flexibility at different angles(0°,45°,90°,180°)along with a good flexible cycling stability after 6000 cycles(92.7%capacitance retention).To date,such a novel poly(ionic liquid)-graphene fiber supercapacitors would be a new platform in real-time flexible electronics.

Cardiogenic differentiation of mesenchymal stem cells on elastomeric poly (glycerol sebacate)/collagen core/shell fibers

AIM: To facilitate engineering of suitable biomaterials to meet the challenges associated with myocardial infarction. METHODS: Poly (glycerol sebacate)/collagen (PGS/ collagen) core/shell fibers were fabricated by core/ shell electrospinning technique, with core as PGS and shell as collagen polymer; and the scaffolds were characterized by scanning electron microscope (SEM), fourier transform infrared spectroscopy (FTIR), contact angle and tensile testing for cardiac tissue engineering. Collagen nanofibers were also fabricated by electrospinning for comparison with core/shell fibers. Studies on cell-scaffold interaction were carriedout using cardiac cells and mesenchymal stem cells (MSCs) co-culture system with cardiac cells and MSCs separately serving as positive and negative controls respectively. The co-culture system was characterized for cell proliferation and differentiation of MSCs into cardiomyogenic lineage in the co-culture environment using dual immunocytochemistry. The co-culture cells were stained with cardiac specific marker proteins like actinin and troponin and MSC specific marker protein CD 105 for proving the cardiogenic differentiation of MSCs. Further the morphology of cells was analyzed using SEM.RESULTS: PGS/collagen core/shell fibers, core is PGS polymer having an elastic modulus related to that of cardiac fibers and shell as collagen, providing natural environment for cellular activities like cell adhesion, proliferation and differentiation. SEM micrographs of electrospun fibrous scaffolds revealed porous, beadless, uniform fibers with a fiber diameter in the range of 380 ± 77 nm and 1192 ± 277 nm for collagen fibers and PGS/collagen core/shell fibers respectively. The obtained PGS/collagen core/shell fibrous scaffolds were hydrophilic having a water contact angle of 17.9 ± 4.6° compared to collagen nanofibers which had a contact angle value of 30 ± 3.2°. The PGS/collagen core/shell fibers had mechanical properties comparable to that of native heart muscle with a young's modulus of 4.24 ± 0.7 MPa, while that of collagen nanofibers was comparatively higher around 30.11 ± 1.68 MPa. FTIR spectrum was performed to confirm the functional groups present in the electrospun scaffolds. Amide Ⅰ and amide Ⅱ of collagen were detected at 1638.95 cm -1 and 1551.64 cm -1 in the electrospun collagen fibers and at 1646.22 cm -1 and 1540.73 cm -1 for PGS/collagen core/shell fibers respectively. Cell culture studies performed using MSCs and cardiac cells co-culture environment, indicated that the cellproliferation significantly increased on PGS/collagen core/shell scaffolds compared to collagen fibers and the cardiac marker proteins actinin and troponin were expressed more on PGS/collagen core/shell scaffolds compared to collagen fibers alone. Dual immunofluorescent staining was performed to further confirm the cardiogenic differentiation of MSCs by employing MSC specific marker protein, CD 105 and cardiac specific marker protein, actinin. SEM observations of cardiac cells showed normal morphology on PGS/collagen fibers and providing adequate tensile strength for the regeneration of myocardial infarction. CONCLUSION: Combination of PGS/collagen fibers and cardiac cells/MSCs co-culture system providing natural microenvironments to improve cell survival and differentiation, could bring cardiac tissue engineering to clinical application.

MORPHOLOGIES AND GAS SEPARATION PROPERTIES OF MELT-SPUN ASYMMETRIC POLY(4-METHYL-1-PENTENE)HOLLOW FIBER MEMBRANES

Poly(4-methyl-1-pentene) (PMP) hollow fiber membranes were prepared by the melt-spun and cold-stretch(MSCS) method. Scanning electronic microscopy (SEM) was used to characterize the section and surface structures of themembranes with special asymmetric structure. The preliminary results of gas permeation measurements indicated that the resultant hollow fiber membranes have the potential ability for oxygen/nitrogen separation.

RELEASE OF IBUPROFEN FROM PEG-PLLA ELECTROSPUN FIBERS CONTAINING POLY(ETHYLENE GLYCOL)-b-POLY(α-HYDROXY OCTANOIC ACID) AS AN ADDITIVE

Poly（a-hydroxy octanoic acid） was first used as an additive for the preparation of electrospun ultra-fine fibers of poly（ethylene glycol）-b-poly（L-lactide） （PEG-PLLA）. Ibuprofen was loaded in the electrospun ultra-fine fibers. The results from environmental scanning electron microscopy （ESEM）, wide angle X-ray diffraction （WAXD） and differential scanning calorimetry （DSC） demonstrated that ibuprofen could be perfectly entrapped in the fibers electrospun from PEG-PLLA using a-hydroxy octanoic acid or PEG-b-poly（a-hydroxy octanoic acid） （PEG-PHOA） as additives. Compared with electrospun PEG-PLLA fibers which entrapped 20 wt% ibuprofen, the PEG-PLLA electrospun fibers containing PEG-PHOA exhibited integral and robust after 1 week incubated in 37℃, pH 7.4 phosphate buffer solution with 10 μg/mL proteinase K. Compared with electrospun fibers without PEG-PHOA, the concentration ofproteinase K in release media had less effect on the release rate of ibuprofen. An unique release profile was found from PEG-PLLA fiber after the incorporation of PEG-PHOA. Enzyme degradation experiments demonstrated that PEG-PHOA but not a-hydroxy octanoic acid monomer was the crucial factor for integrity maintenance of the electrospun fibers, which may be due to the enzyme degradation tolerance property of the PEG-PHOA polymer additive.

Effects of coagulation bath temperature on structure and performance of poly(vinyl butyral) hollow fiber membranes via thermally induced phase separation

Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.

The Green Composites: Millet Husk Fiber (MHF) Filled Poly Lactic Acid (PLA) and Degradability Effects on Environment

This study provides an overview on green composites degradability. Practically, the main drawbacks of using natural fibers are their poor dimensional stability, degradability and high degree of moisture absorption. While, end use of product from natural fiber filled or reinforced composites has become subject of concern to material engineers and scientist. The major properties of natural fiber reinforced polymer composites are greatly dependent on the hydrophilic tendency and dimensional stability of the fibers used, morphology aspect ratio for long fiber, while voids for powder fibers. The effects of chemical treatments on cellulosic fibers that are used as reinforcements for thermoplastics were studied. The chemical source for the treatments is alkalization. The significance of chemically-treated natural fibers is seen through the improvement of mechanical properties. The untreated fiber composites degrade faster in municipal soil compared to treated fiber composites.

Enzymatic Modification of Poly (ethylene terephthalate) Fiber with Lipase from Aspergillus oryzae

Lipase preparation from Aspergillus oryzae could act on ester bonds on the surface of poly （ethylene terephthalate） fibers and a possible hydrolytic product mono （2-hydroxyethyl） terephthalate was released. After the iipase modification, there were more carboxyi groups on the treated poly （ethylene terephthalate） fabric surface that resulted in binding with more cationic dyes. Increased hydrophilicity and antistatic ability of poly （ethylene terephthalate） samples were found based on moisture regain, water contact angle and static half decay time.

MECHANICAL PROPERTIES OF CARBON/GLASS FIBER REINFORCED POLY(METHYL METHACRYLATE)COMPOSITES

Artificial bone, carbon/glass fiber reinforced PM-MA composites have been prepared by hot press moulding of pre-preg -which monofilments of CF and GF impregnated by MMA prepolymer. When the PMMA volume fraction in com-posites is 50% > theoretical and experimental results show that strength and modules of these hybrid composites are in accord with 'rule of mixture'. The tensile and flexure strength are the lowest when the raletive volume fraction of carbon fiber in rein-forcements is 50%,SEM examinations further explained re-sults.

Synthesis of polypiperazine-amide thin-film membrane on PPESK hollow fiber UF membrane

A new interfacial polymerization （IP） procedure is developed in order to synthesize polypiperazine-amide thin-film membrane on the inner surface of poly（phthalazinone ether sulfone ketone） （PPESK） hollow fiber ultrafiltration （UF） membrane. A hollow fiber composite membrane with good performance was prepared and studied by PT-IR and scanning electron microscopy.

Covalent Immobilization of Lipase on Poly(acrylonitrile-co-maleic acid) Ultrafiltration Hollow Fiber Membrane

Lipase from Candida rugosa was covalently immobilized on the surface of an uhrafihration hollow fiber membrane fabricated from poly （ acrylonitrile-co-maleic acid） （ PANCMA ） in which the carboxyl groups were activated with 1-ethyl-3-（ dimethylaminopropyl ） carbodiimide hydrochloride （ EDC ） and dicyclohexyl carbodiimide （ DCC ）/ N-hydroxyl succinimide（NHS）, respectively. The properties of the immobilized lipase were assayed and compared with those of the free enzyme. The maximum activities were observed in a relatively broader pH value range at high temperatures for the immobilized lipase compared to the free one. It was also found that the thermal and pH stabilities of lipase were improved upon immobilization and at 50 ℃ the thermal inactivation rate constant values are 2. 1 × 10^ -2 for the free lipase, 3.2 × 10^-3 for the immobilized lipase on the EDC-activated PANCMA membrane and 3.5 × 10^-3 for the immobilized lipase on the DCC/NHS-activated PANCMA membrane, respectively.

Mechanical Property and Crystal Structure of Poly(p-phenylene terephthalamide)(PPTA) Fibers during Heat Treatment under Tension

The relationship between property and structure of poly( p-phenylene terephthalamide)( PPTA) was investigated for the purpose of obtaining products with better performance. PPTA fiber subjected to heat treatment under different conditions was intensively studied. Simultaneous wide-angle X-ray diffraction( WAXD) technique was introduced to study the changes of crystal structure. It was found that the tensile modulus was strongly sensitive to the levels of temperature and tension. The structure parameters including crystal size and crystal orientation after heat treatment evolve similarly to the tensile modulus,indicating a direct structure-property relationship. The lattic c-dimension increases after heat treatment and is greatly affected by the tension. An optimal temperature can be found around 400 ℃,where big change can happen in the crystal structure due to α-relaxation in the crystal region as supported in dynamic mechanical analysis( DMA).

Electrokinetic phenomena of poly(vinyl butyral) hollow fiber membranes in different electrolyte solutions

The streaming potential of poly（vinyl butyral） （PVB） hollow fiber membrane was studied in different electrolyte solutions （including NaCl, KCl, CaCl2 and MgCl2）, the effects of ionic strength, ion valence and pH value on the streaming potential （SP） of the membrane were investigated. The zeta potentials and surface charge densities of the membrane were estimated on the basis of Helmholtz-Smoluchowski equation and Gouy-Chapmann theory. The results show that the PVB membrane has a weak negative charge due to the specific adsorption of ions. Moreover, the streaming potential, the zeta potential and the surface charge density of the membrane depend strongly on the salt concentration and the type and valence of ions. The iso-electric point （IEP） of the PVB membrane is arotmd 3.0 in the monovalent media （NaC1 and KC1） and 3.5 in divalent electrolytes （CaCl2 and MgCl2）. A few retentions were obtained for PVB membrane in low concentration solutions. This result verifies that the negative charged membrane surface can reject inorganic solutes by means of electrostatic repulsion effect even though the size of membrane pores is much larger than the size of salts.

Crystallization and Dynamic Mechanical Behavior of Coir Fiber Reinforced Poly(Butylene Succinate)Biocomposites

The crystallization behavior,crystal morphology and form,and viscoelastic behavior of poly(butylene succinate)(PBS)and coir fiber/PBS composites(CPB)were investigated by differential scanning calorimetry(DSC),polarized optical microscopy(POM),X-ray diffraction(XRD)and dynamic mechanical analysis(DMA).The results of DSC measurement show that the crystallization temperature increases with the filling of coir fibers.POM images reveal that the spherulitic size and crystallization behavior of PBS are influenced by the coir fibers in the composites.XRD curves show that the crystal form of pure PBS and CPB are remaining almost identical.In addition,the storage modulus of CPB significantly increases comparing with the pure PBS.This predicted the dimensional stability and improved load-deformation temperature.In conclusion,the addition of coir fibers has a significant effect on the thermal properties of the matrix.

Antifouling Properties of Electrospun Polymeric Coatings Induced by Controlled Surface Morphology

Nosocomial infections affect implanted medical devices and greatly challenge their functional outcomes,becoming sometimes life threatening for the patients.Therefore,aggressive antibiotic therapies are administered,which often require the use of last-resort drugs,if the infection is caused by multi-drug-resistant bacteria.Reducing the risk of bacterial contamination of medical devices in the hospitals has thus become an emerging issue.Promising routes to control these infections are based on materials provided with intrinsic bactericidal properties(i.e.,chemical action)and on the design of surface coatings able to limit bacteria adhesion and fouling phenomena(i.e.,physical action),thus preventing bacterial biofilm formation.Here,we report the development and validation of coatings made of layer-by-layer deposition of electrospun poly(vinylidene fluoride-co-trifluoro ethylene)P(VDF-TrFE)fibers with controlled orientations,which ultimately gave rise to antifouling surfaces.The obtained 10-layer surface morphology with 90°orientation fibers was able to efficiently prevent the adhesion of bacteria,by establishing a superhydrophobic-like behavior compatible with the Cassie-Baxter regimen.Moreover,the results highlighted that surface wettability and bacteria adhesion could be controlled using fibers with diameter comparable to bacteria size(i.e.,achievable via electrospinning process),by tuning the intra-fiber spacing,with relevant implications in the future design of biomedical surface coatings.

Removal of manganese from waste water by complexation-ultrafiltration using copolymer of maleic acid and acrylic acid

Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.

Effects of F127 on Properties of PVB/F127 Blend Hollow Fiber Membrane via Thermally Induced Phase Separation

Hydrophilic poly(vinyl butyral)(PVB) /Pluronic F127(F127) blend hollow fiber membranes were prepared via thermally induced phase separation(TIPS) ,and the effects of blend composition on the performance of hydrophilic PVB/F127 blend hollow fiber membrane were investigated.The addition of F127 to PVB/polyethylene glycol(PEG) system decreases the cloud point temperature,while the cloud point temperature increases slightly with the addition of F127 to 20%(by mass) PVB/F127/PEG200 system when the concentration of F127 is not higher than 5%(by mass) .Light scattering results show that the initial inter-phase periodic distance formed from the phase separation of 20%(by mass) PVB/F127/PEG200 system decreases with the addition of F127,so does the growth rate during cooling process.The blend hollow fiber membrane prepared at air-gap 5mm,of which the water permeability increases and the rejection changes little with the increase of F127 concentration.For the membrane prepared at zero air-gap,both water permeability and rejection of the PVB/F127 blend membrane are greater than those of PVB membrane,while the tensile strength changes little.Elementary analysis shows that most F127 in the polymer solution can firmly exist in the polymer matrix,increasing the hydrophilicity of the blend membrane prepared at air-gap of 5mm.

Effects of Additives and Coagulant Temperature on Fabrication of High Performance PVDF/Pluronic F127 Blend Hollow Fiber Membranes via Nonsolvent Induced Phase Separation

Poly（vinylidene fluoride） （PVDF） has become one of the most popular materials for membrane preparation via nonsolvent induced phase separation （NIPS） process. In this study, an amphiphilic block copolymer, Pluronic F127, has been used as both a pore-former and a surface-modifier in the fabrication of PVDF hollow fibermembranes to enhance the membrane permeability and hydrophilicity. The effects of 2nd additive and coagulant temperature on the formation of PVDF/Pluronic F 127 membranes have also been investigated. The as-spun hollow fibers were characterized in terms of cross-sectional morphology, pure water permeation （PWP）, relative molecular mass cut-off （MWCO）, membrane chemistry, and hydrolphilicity. It was obsered that the addition of Pluronic F 127 significantly increased the PWP of as-spun fibers, while the membrane contact angle was reduced. However, the size of macrovoids in the membranes was undesirably large. The addition of a 2nd additive, including lithium chloride （LiC1） and water, or an increase in coagulant temperature was found to effectively suppress the macrovoid for- mation in the Pluronic-containing membranes. In addition, the use of LiC1 as a 2nd additive also further enhanced the PWP and hydrophilicity of the membranes, while the surface pore size became smaller. PVDF hollow fiber with a PWP as high as 2330 L·m-2·h-1·MPa-1, a MWCO of 53000 and＇a contact angle of 71 o was successfully fabricated with 3% （by mass） of Pluronic F127 and 3% （by mass） of LiC1 at a coagulant temperature of 25 ℃, which shows better performance as compared with most of PVDF hollow fiber membranes made by NIPS method.