“Polymer-in-ceramic” based poly(ε-caprolactone)/ceramic composite electrolyte for all-solid-state batteries

Inspired by the concept of "polymer-in-ceramic",a composite poly(ε-caprolactone)(PCL)/ceramic containing LiTFSI is prepared and investigated as a solid electrolyte for all-solid-state batteries.The composite with the optimum concentration of 45 wt% LiTFSI and 75 wt% Li1.5Al0.5Ge1.5(PO4)3(LAGP,NASICON-type structure) exhibits a high ionic conductivity(σi=0.17 mS cm-1) at 30℃,a transference number of 0.30,and is stable up to 5.0 V.The composite electrolyte is a flexible and self-standing membrane.Solid-state LiFePO4//Li batteries with this composite electrolyte demonstrate excellent cycling stability with high discharge capacity of 157 mA h g-1,high capacity retention of 96% and coulombic efficiency of 98.5% after 130 cycles at 30℃ and 0.1 C rate.These electrochemical properties are better than other PCL-based allsolid-lithium batteries,and validate the concept of "polymer-in-ceramic" by avoiding the drawback of lower conductivity in prior "polymer-in-ceramic" electrolyte at high concentration of the ceramic.

Structure Changes of Silk Fibroin(SF) by Blending with Poly(ε-caprolactone)(PCL):Characterization of SF and PCL Blended Electrospinning Films

The mechanical properties and water solubility of electrospinning SF films limit their use as biomaterials. In order to develop a tissue engineering biomaterial with both satisfying biological properties and sufficient biomechanical properties,blended films composed of silk fibroin( SF) and poly( ε-caprolactone)( PCL) were fabricated by electrospinning in this study. Scanning electron microscope( SEM), X-ray diffraction( XRD),thermal analysis,Fourier transform-infrared( FT-IR),Raman spectra,mechanical testing,and water solubility were used to characterize the morphological, structural and mechanical properties of the blended electrospinning films. Results showed that the diameter of the blended fiber was distributed between 600 and1000 nm,and the fiber diameter increased as the PCL content increased. There is no obvious phase separation due to the similarity and intermiscibility,as well as the interactions( mainly hydrogen bonds), between the two polymers. Meanwhile, the secondary structures of SF changed from random coils and Silk I to Silk II because of the interactions between SF and PCL. For this reason,the tensile strength and elongation at break of the electrospinning films improved significantly,and the water solubility decreased. In conclusion,the blended electrospinning films fabricated in this study showed satisfying mechanical properties and water insolubilities,and they may be promising biomaterials for applications in tissue engineering for blood vessels,nerve conduits,tendons,ligaments and other tissues.

Novel electrospun poly(ε-caprolactone)/type Ⅰ collagen nanofiber conduits for repair of peripheral nerve injury

Recent studies have shown the potential of artificially synthesized conduits in the repair of peripheral nerve injury. Natural biopolymers have received much attention because of their biocompatibility. To investigate the effects of novel electrospun absorbable poly(ε-caprolactone)/type Ⅰ collagen nanofiber conduits(biopolymer nanofiber conduits) on the repair of peripheral nerve injury, we bridged 10-mm-long sciatic nerve defects with electrospun absorbable biopolymer nanofiber conduits, poly(ε-caprolactone) or silicone conduits in Sprague-Dawley rats. Rat neurologica1 function was weekly evaluated using sciatic function index within8 weeks after repair. Eight weeks after repair, sciatic nerve myelin sheaths and axon morphology were observed by osmium tetroxide staining, hematoxylin-eosin staining, and transmission electron microscopy.S-100(Schwann cell marker) and CD4(inflammatory marker) immunoreactivities in sciatic nerve were detected by immunohistochemistry. In rats subjected to repair with electrospun absorbable biopolymer nanofiber conduits, no serious inflammatory reactions were observed in rat hind limbs, the morphology of myelin sheaths in the injured sciatic nerve was close to normal. CD4 immunoreactivity was obviously weaker in rats subjected to repair with electrospun absorbable biopolymer nanofiber conduits than in those subjected to repair with poly(ε-caprolactone) or silicone. Rats subjected to repair with electrospun absorbable biopolymer nanofiber conduits tended to have greater sciatic nerve function recovery than those receiving poly(ε-caprolactone) or silicone repair. These results suggest that electrospun absorbable poly(ε-caprolactone)/type Ⅰ collagen nanofiber conduits have the potential of repairing sciatic nerve defects and exhibit good biocompatibility. All experimental procedures were approved by Institutional Animal Care and Use Committee of Taichung Veteran General Hospital, Taiwan, China(La-1031218) on October 2, 2014.

PREPARATION AND CHARACTERIZATION OF INCLUSION COMPLEXES OF TWO-ARM LINEAR AND FOUR-ARM STAR-SHAPED POLY(ε-CAPROLACTONE)S WITHα-CYCLODEXTRIN

Both four-ann star-shaped poly（ε-caprolactone） （4sPCL） and two-ann linear PCL （2LPCL） were synthesized and their inclusion complexation with α-cyclodextrin （α-CD） were studied. The inclusion complexes （ICs） formed between the PCL polymers and α-CD were characterized by ^1H-NMR, DSC, TGA, WAXD, and FT-1R, respectively. Both branch ann number and molecular weight of the PCL polymers have apparent effect on the stoichiometry （CL：CD, mol：mol） of these ICs. All these analytical results indicate that the branch arms of the PCL polymers are incorporated into the hydrophobic α-CD cavities and their original crystalline properties are completely suppressed. Moreover, the inclusion complexation between two-ann linear or four-ann star-shaped PCL polymers and α-CD not only enhances the thermal stability of the guest PCL polymers but also improves that of α-CD.

Effect of Poly(ε-caprolactone-b-tetrahydrofuran)Triblock Copolymer Concentration on Morphological,Thermal and Mechanical Properties of Immiscible PLA/PCL Blends

In this study a low molecular weight triblock copolymer derived fromε-caprolactone and tetrahydrofuran was used as a non-reactive compatibilizer of immiscible PLA/PCL blends.Ternary blends with 0,1.5 wt%,3 wt%and 5 wt% copolymer and about 75 wt%PLA were prepared by single screw extrusion and characterized by scanning electron microscopy(SEM),differential scanning calorimetry(DSC),dynamic mechanical analysis(DMA),tensile and Izod impact testing.SEM micrographs showed that the size of the dispersed PCL domains was practically constant regardless of copolymer concentration.This result can be explained by the low shear rate employed during processing step and a decrease of PCL viscosity by presence of the triblock copolymer.However,when the copolymer concentration increased,strain at break of PLA/PCL blends also increased.PLA/PCL blend with 0 wt% copolymer presented 2%strain at break,whereas PLA/PCL blend with 5 wt%copolymer exhibited 90%.

MOLECULAR WEIGHT DEPENDENCE OF THE MELTING BEHAVIOR OF POLY(ε-CAPROLACTONE)

Poly(ε-caprolactone) (PCL) with different molecular weights was synthesized and characterized by a gelpermeation chromatograph equipped with multiple detector. The melting behavior of PCL was also studied. It was found thatthe equilibrium melting points (T_m^0) of PCL samples depend on their molecular weights. Wide angle X-ray diffractionmeasurements (WAXD) and DSC measurements showed that the crystals of the high molecular weight PCLs were moreperfect than those of the low molecular weigh ones. These results demonstrate that the concentration of the end groups ofPCL chains is the main factor that influences the melting behavior. The fusion enthalpy per repeating unit (ΔH_u) wasdetermined to be 11.3 kJ/mol for PCL.

HETEROCYCLIC SCHIFF BASE NEODYMIUM COMPLEX AS CATALYST FOR RING-OPENING POLYMERIZATION OF ε-CAPROLACTONE

An aromatic heterocyclic Schiff base neodymium complex bearing thiazole was synthesized and its activity in the ring-opening polymerization ofε-caprolactone(CL)was examined.The conditions of the CL/Nd molar ratio,monomer concentration,polymerization time and temperature were investigated.Activities of ca.171 kg/Nd·h were obtained under the optimum condition(CL/Nd=1600(molar ratio),[CL]=2.26 mol L^(-1),1 h at 50℃),giving a poly(ε-caprolactone)(PCL)of number-average molecular weight M_n=5.4×10~4 and molecular...

4天香烟烟雾暴露联合poly(I:C)刺激对小鼠肺部免疫应答及干扰素表达的影响

目的:探讨短期香烟烟雾暴露联合poly(I:C)刺激对小鼠肺部免疫应答及干扰素表达的影响。方法:BALB/c小鼠随机分为4组:对照组、熏烟组、poly(I:C)组和熏烟联合poly(I:C)组。检测支气管肺泡灌洗液(BALF)中总细胞数及细胞分类计数;普通光镜下观察各组细胞形态;荧光定量PCR检测肺组织细胞因子、趋化因子和干扰素及干扰素刺激基因表达。结果:与对照组相比,熏烟联合poly(I:C)组总细胞数计数、巨噬细胞与中性粒细胞计数明显升高(P<0.05),且熏烟联合poly(I:C)组巨噬细胞计数高于poly(I:C)组;与poly(I:C)组比较,熏烟联合poly(I:C)组小鼠气道灌洗液巨噬细胞体积较大,呈圆形或不规则形,细胞质较多空泡;与对照组相比,熏烟联合poly(I:C)组小鼠肺组织中性粒细胞趋化因子CXCL1(P<0.05)、CXCL2(P<0.01)和淋巴细胞趋化因子CCL2(P<0.01)mRNA表达升高,肺组织IL-1β、IL-6、TNF-αmRNA表达明显升高(P<0.01),肺组织IFN-β(P<0.01)、IFN-γ(P<0.05)、MX2(P<0.01)和IP-10(P<0.01)表达显著升高,且与poly(I:C)组小鼠相比,熏烟联合poly(I:C)组小鼠肺组织CXCL2(P<0.05)、TNF-α(P<0.01)和IFN-β(P<0.05)mRNA表达明显升高。结论:熏烟联合poly(I:C)诱导了小鼠肺部炎症反应和干扰素及干扰素刺激基因表达。同时,香烟暴露加剧了poly(I:C)诱导的小鼠肺部急性炎症反应和Ⅰ型干扰素表达。

RING-OPENING POLYMERIZATION OFε-CAPROLACTONE USING LANTHANIDE TRIS(N-PHENYL-3,5-DI-T-BUTYLSALICYLALDIMINATO)S AS SINGLE COMPONENT CATALYST

Ring-opening polymerization of ε-caprolactone has been carried out by using rare earth Schiff base complexes： lanthanide tris（N-phenyl-3,5-di-t-butylsalicylaldiminato）s [Ln（OPBS）3] as single component catalyst for the first time. The influences of different rare earth elements, monomer and catalyst concentration as well as reaction time on the polymerization were investigated. Mechanism studies showed that monomer inserts into the active site with the acyl-oxygen bond scission rather than the break of alkyl-oxygen bond.

Stable Cycling of All-Solid-State Lithium Metal Batteries Enabled by Salt Engineering of PEO-Based Polymer Electrolytes

Poly(ethylene oxide)(PEO)-based polymer electrolytes show the prospect in all-solid-state lithium metal batteries;however,they present limitations of low room-temperature ionic conductivity,and interfacial incompatibility with high voltage cathodes.Therefore,a salt engineering of 1,1,2,2,3,3-hexafluoropropane-1,3-disulfonimide lithium salt(LiHFDF)/LiTFSI system was developed in PEO-based electrolyte,demonstrating to effectively regulate Li ion transport and improve the interfacial stability under high voltage.We show,by manipulating the interaction between PEO matrix and TFSI^(-)-HFDF^(-),the optimized solid-state polymer electrolyte achieves maximum Li+conduction of 1.24×10^(-4)S cm^(-1)at 40℃,which is almost 3 times of the baseline.Also,the optimized polymer electrolyte demonstrates outstanding stable cycling in the LiFePO_(4)/Li and LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2)/Li(3.0-4.4 V,200 cycles)based all-solid-state lithium batteries at 40℃.

Flexible and Robust Functionalized Boron Nitride/Poly(p‑Phenylene Benzobisoxazole)Nanocomposite Paper with High Thermal Conductivity and Outstanding Electrical Insulation

With the rapid development of 5G information technology,thermal conductivity/dissipation problems of highly integrated electronic devices and electrical equipment are becoming prominent.In this work,“high-temperature solid-phase&diazonium salt decomposition”method is carried out to prepare benzidine-functionalized boron nitride(m-BN).Subsequently,m-BN/poly(pphenylene benzobisoxazole)nanofiber(PNF)nanocomposite paper with nacremimetic layered structures is prepared via sol–gel film transformation approach.The obtained m-BN/PNF nanocomposite paper with 50 wt%m-BN presents excellent thermal conductivity,incredible electrical insulation,outstanding mechanical properties and thermal stability,due to the construction of extensive hydrogen bonds andπ–πinteractions between m-BN and PNF,and stable nacre-mimetic layered structures.Itsλ∥andλ_(⊥)are 9.68 and 0.84 W m^(-1)K^(-1),and the volume resistivity and breakdown strength are as high as 2.3×10^(15)Ωcm and 324.2 kV mm^(-1),respectively.Besides,it also presents extremely high tensile strength of 193.6 MPa and thermal decomposition temperature of 640°C,showing a broad application prospect in high-end thermal management fields such as electronic devices and electrical equipment.

Tetrahydrosalen backboned gadolinium complex as initiator for the ring-opening polymerization of ε-caprolactone

Tetrahydrosalen ligand was employed in the synthesis of gadolinium complex. The ligand was deprotoned by LiBu, and the afforded lithium salt was reacted with anhydrous GdCl3 to produce the gadolinium complex through salt metathesis. This complex was successfully used to initiate the ring-opening polymerization of ε-caprolactone. The initiation conditions in different temperature, monomer-to-initiator ratio and time were investigated. Under the condition： [ε-caprolactone]：[catalyst] = 600, 56 ℃, toluene： 2 ml, poly（ε-caprolactone） （PCL） with Mw = 11,2782 and PDI = 1.96 was achieved.

AN APPROACH TO SYNTHESIZE POLY(ETHYLENE GLYCOL)-b-POLY(ε-CAPROLACTONE) WITH TERMINAL AMINO GROUP via SCHIFF'S BASE AS AN INITIATOR

A new method to synthesize a degradable terminal amino group-containing copolymer,poly(ethylene glycol)-b- poly(ε-caprolactone)(MPEG-PCL-NH_2),was developed in the following three steps:(1)the ring-opening polymerization (ROP)ofε-caprolactone from the Schiff base prepared from benzatdehyde and ethanolamine(Ph-CH=NCH_2CH_2OH)used as an initiator to obtain heterobifunctional poly(ε-caprolactone)with one terminal Schiff base group and one hydroxyl group (HO-PCL-CH_2CH_2N=CH-Ph);(2)the coupling reaction of two ...

TRANSESTERIFICATION OF POLY(ETHYLENE TEREPHTHALATE) WITH POLY(ε-CAPROLACTONE)

Transesterification of poly（ethylene terephthalate） （PET） with poly（ε-caprolactone） （PCL） was investigated bymeans of NMR spectroscopy, extraction experiments, differential scanning calorimetry （DSC） and phase contrast microscopy（PCM）. The;H-NMR results show that transesterification takes place in the melt blends and leads to the formation of thePET-PCL copolyester with a chemical structure similar to ethylene terephthalate-ε-caprolactonc copolycster （TCL）synthesized directly from monomers. However, even in the blend that has been transesterified for 8 h, the random PET-PCLcopolyester, PET-PCL copolyester with long PET or long PCL segments and the unreacted PET and PCL homopolymersmay coexist. Due to the low mobility of PET and PCL chains and the high viscosity of the two macromolecules, thetransesterification proceeds with difficulty. Furthermore, PET is incompatible with PCL, the transesterification can onlyoccur at the interface or in the interfacial region between two phases, and finally the reaction can only reach a localequilibrium. These results indicate that in fact the transesterification in the melt blend between two incompatiblehomopolymers could not lead to the formation of completely random or typical block copolyesters.

Synthesis and Characterization of ABBA Block Copolymer of Glycolide and ε-Caprolactone

A biodegradable ABBA block copolymer was synthesized via the ring-opening co-polymerization of ~ε-caprolactone(CL, B) and glycolide(A) by means of step polymerization in the presence of ethylene glycol as an initiator and stannous octanoate as a catalyst at 110 ℃ for 48 h. The molecular length of the PCL pre-polymer(BB) could be adjusted by controlling the molar ratio of the ethylene glycol initiator to ε-caprolactone monomer. The structure and the composition of the block copolymer were determined by the weight ratio of the monomer glycolide(A) to PCL pre-polymer(BB). The block copolymers were characterized by ~ 1H NMR, GPC, DSC and X-ray. The results confirm the successful synthesis of an ABBA block copolymer.

Synthesis of Highly Branched Poly(ε-caprolactone) by Self-condensing Atom Transfer Radical Polymerization of Macroinimers

Branched poly（ε-capmlactone） was synthesized by self-condensing atom transfer radical polymerization of macroinimer, α-acryloyoxy-ω-2-bromopropionyloxy poly（ε-caprolactone）, which was prepared by enzyme-catalyzed ring-opening polymerization of ε-caprolactone with 2-hydroxylethyl acrylate as initiator and esterification of the ω-hydroxyl group of the obtained poly（ε-caprolactone） by 2-bromopropionyl bromide.

Research in the Degradation and Antifouling Performance of Copolyesters of L-Lactide and ε-Caprolactonen

Block copolyesters of L-lactide and ε-caprolactone were synthesized by melt copolymerization of ε-caprolactone and L-lactide.The degradation performance of copolyesters was investigated by quartz crystal microbalance with dissipation(QCM-D).Diisocyanate terminated copolyesters could obtain via the reaction of copolyesters and diisocyanate.Diisocyanate terminated copolyesters could react with polyol resin to prepare degradable polyurethane which can be used in antifouling coatings.In this paper,we also discussed the degradation products release action and antifouling performance of the copolyesters film.

Electrospun Chitosan( CS)/Poly( L-lactic-co-ε-caprolactone)( PLCL ) Nanofibers and Their Potential as Small-Diameter Vascular Scaffold

The ideal small-diameter vascular grafts should mimic the nanostructure and mechanical properties of nature blood vessel. In this study, electrospun chitosan( CS)/poly( L-lactic-co-ε-caprolactone)( PLCL) nanofibers were developed for potential small-diameter blood vessel applications. CS is a positively charged polymer which is beneficial for cell attachment and growth,while PLCL provides favorable mechanical support due to its excellent elasticity. Typical nanofibrous structure was observed in both CS/PLCL and pure PLCL scaffolds. The optimal mechanical property could be achieved when the weight ratio of CS/PLCL was 1 ∶ 2.Compared with pure PLCL scaffolds, the CS/PLCL scaffolds showed higher hydrophilicity and markedly promoted the attachment,spreading and proliferation of human umbilical vein endothelial cells( HUVECs). Hence,CS/PLCL scaffolds can be used as potential vascular grafts.

EPITAXIAL CRYSTALLIZATION OF POLY(ε-CAPROLACTONE)ON HIGHLY ORIENTED ISOTACTIC POLYPROPYLENE

Electron microscope and electron diffraction have been used to study epitaxial crystallization of poly(ε-caprolactone)(PCL).on highly oriented film of isotactic polypropylene(iPP).The results obtained from bright field(BF)electron micrograph and electron diffraction indicate that the PCL can epitaxially grow on iPP substrate and form cross-hatched lamellar texture.The c axes of PCL are ±500 apart from the c axes of iPP. The contact planes of the two kinds of crystals are(010)of iPP and(100) of PCL,respectively.