Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carbo...Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.展开更多
Neurological injury caused by ischemic stroke is a major cause of permanent disability and death. The currently available neuroprotective drugs fail to achieve desired therapeutic efficacy mainly due to short circulat...Neurological injury caused by ischemic stroke is a major cause of permanent disability and death. The currently available neuroprotective drugs fail to achieve desired therapeutic efficacy mainly due to short circulation half-life and poor blood−brain barrier (BBB) permeability. For that, an edaravone-loaded pH/glutathione (pH/GSH) dual-responsive poly(amino acid) nanogel (NG/EDA) was developed to improve the neuroprotection of EDA. The nanogel was triggered by acidic and EDA-induced high-level GSH microenvironments, which enabled the selective and sustained release of EDA at the site of ischemic injury. NG/EDA exhibited a uniform sub-spherical morphology with a mean hydrodynamic diameter of 112.3 ± 8.2 nm. NG/EDA efficiently accumulated at the cerebral ischemic injury site of permanent middle cerebral artery occlusion (pMCAO) mice, showing an efficient BBB crossing feature. Notably, NG/EDA with 50 µM EDA significantly increased neuron survival (29.3%) following oxygen and glucose deprivation by inhibiting ferroptosis. In addition, administering NG/EDA for 7 d significantly reduced infarct volume to 22.2% ± 7.2% and decreased neurobehavioral scores from 9.0 ± 0.6 to 2.0 ± 0.8. Such a pH/GSH dual-responsive nanoplatform might provide a unique and promising modality for neuroprotection in ischemic stroke and other central nervous system diseases.展开更多
Biodegradable chitosan-g-poly (D, L-lactic acid) copolymers were prepared via two methods. (1) The lactide was grafted onto hydroxyl groups of chitosan by using macromolecular initiator sodium of trimethylsilyl-chit...Biodegradable chitosan-g-poly (D, L-lactic acid) copolymers were prepared via two methods. (1) The lactide was grafted onto hydroxyl groups of chitosan by using macromolecular initiator sodium of trimethylsilyl-chitosan, (2) poly (D,L-lactic acid)(PLA) with low molecular weight can be linked to the amino group by coupling activated PLA to trimethylsilyl-chitosan. Two graft copolymers had hydrophilic-hydrophobic character and can be applied as carriers for drug delivery.展开更多
A novel kind of copolymer with ABA-type block structure was synthesized by anionic ring-opening polymerization of beta-butyrolactone (beta-BL) in the presence of a PEG-based dicarboxylates as macroinitiators which wer...A novel kind of copolymer with ABA-type block structure was synthesized by anionic ring-opening polymerization of beta-butyrolactone (beta-BL) in the presence of a PEG-based dicarboxylates as macroinitiators which were prepared by the esterification of aliphatic cyclic anhydride and poly(ethylene glycol) (PEG) oligomers (M-n = 2000, 4000 and 6000) and conversion of potassium dicarboxylates. The resultant copolymers as well as the intermediates were characterized by IR, H-1-NMR and GPC.展开更多
This study aims to beneficiate low grade goethitic iron ore fines using a selective flocculation process. Selective flocculation studies were conducted using different polymers such as starch amylopectin(AP), poly acr...This study aims to beneficiate low grade goethitic iron ore fines using a selective flocculation process. Selective flocculation studies were conducted using different polymers such as starch amylopectin(AP), poly acrylic acid(PAA), and a graft copolymer(AP-g-PAA). The obtained results were analyzed; they indicate the enhancement of the iron ore grade from 58.49% to 67.52% using AP-g-PAA with a recovery of 95.08%. In addition, 64.45% Fe with a recovery of 88.79% was obtained using AP. Similarly, using PAA, the grade increased to 63.46% Fe with a recovery of 82.10%. The findings are also supported by characterizing concentrates using X-ray diffraction(XRD) and electron probe microanalysis(EPMA) techniques.展开更多
Poly[（alanino ethyl ester）0.67 （glycino ethyl ester）0.33 phosphazene] （PAGP） was synthesized, and morphology and diameter of the electrospun PAGP nanofibers were systematically evaluated by using a cool field em...Poly[（alanino ethyl ester）0.67 （glycino ethyl ester）0.33 phosphazene] （PAGP） was synthesized, and morphology and diameter of the electrospun PAGP nanofibers were systematically evaluated by using a cool field emission scanning electron microscope （SEM） with changing the important processing variables such as applied voltage, polymeric concentration, and ambient temperature. The average diameter of PAGP nanofibers was inversely proportional to the applied voltage, but increased with the increase of solution concentration. Lower environmental temperature was unfavorable due to the nanofibers conglutination.展开更多
Hydrophilic degraded gelatin was modified with hydrophobic poly(ε-caprolactone) (PCL) via a chemical grafting route.Firstly,PCL with one hydroxyl end group was prepared by the ring-opening polymerization of εcaprola...Hydrophilic degraded gelatin was modified with hydrophobic poly(ε-caprolactone) (PCL) via a chemical grafting route.Firstly,PCL with one hydroxyl end group was prepared by the ring-opening polymerization of εcaprolactone (ε-CL) with tin (Ⅱ) 2-ethylhexanoate as catalyst and n-butyl alcohol as initiator.Secondly,the PCL reacted with isophorone diisocyanate (IPDI) to prepare PCL with isocyanate functional group (PCL-NCO).Hydroxylamine was used to degrade gelatin by the cleavage between asparagine and glycine residues of gelatin.PCL-NCO reacted with the hydroxyl/amino groups of degraded gelatin in a homogeneous system and yielded the PCL modified gelatin copolymers.The gelatin grafted PCL copolymers were measured by means of XRD,FTIR,DSC and 1 H NMR.The results confirmed the conjugation of PCL onto gelatin chains.The PCL modified gelatin can be used as biomaterials owing to their biocompatibility and biodegradation.展开更多
In this study a low molecular weight triblock copolymer derived fromε-caprolactone and tetrahydrofuran was used as a non-reactive compatibilizer of immiscible PLA/PCL blends.Ternary blends with 0,1.5 wt%,3 wt%and 5 w...In this study a low molecular weight triblock copolymer derived fromε-caprolactone and tetrahydrofuran was used as a non-reactive compatibilizer of immiscible PLA/PCL blends.Ternary blends with 0,1.5 wt%,3 wt%and 5 wt% copolymer and about 75 wt%PLA were prepared by single screw extrusion and characterized by scanning electron microscopy(SEM),differential scanning calorimetry(DSC),dynamic mechanical analysis(DMA),tensile and Izod impact testing.SEM micrographs showed that the size of the dispersed PCL domains was practically constant regardless of copolymer concentration.This result can be explained by the low shear rate employed during processing step and a decrease of PCL viscosity by presence of the triblock copolymer.However,when the copolymer concentration increased,strain at break of PLA/PCL blends also increased.PLA/PCL blend with 0 wt% copolymer presented 2%strain at break,whereas PLA/PCL blend with 5 wt%copolymer exhibited 90%.展开更多
A series of novel copolymers were successfully synthesized by ring-opening polymerization （ROP） of 3 （S）-methyl-morpholine-2,5-dione （MMD） and 5-methyl-5-benzyloxycarbonyl-1,3-dioxan-2-one （MBC） using stan- no...A series of novel copolymers were successfully synthesized by ring-opening polymerization （ROP） of 3 （S）-methyl-morpholine-2,5-dione （MMD） and 5-methyl-5-benzyloxycarbonyl-1,3-dioxan-2-one （MBC） using stan- nous octoate as catalyst. The copolymers were characterized by means of ~H-NMR and FT-IR spectroscopy. Gel permeation chromatography （GPC） test shows that the average-number relative molecular mass and average-weight rela- tive molecular mass slightly increase with the increase of MBC content in feed. The results of differential scanning calorimetry （DSC） demonstrate that the glass transition temperature of copolymers increases with the increase of MBC content in copolymers. The copolymers of MMD and MBC are amorphous copolymers, as indicated by DSC results, while the homopolymer of MMD is semicrystalline.展开更多
Main observation and conclusion Block copolymers not only combine properties of different segments but also generate new application prospects.Poly(α-amino acid)-b-poly(tetrahydrofuran)-b-poly(α-amino acid)(PAA-PTHF...Main observation and conclusion Block copolymers not only combine properties of different segments but also generate new application prospects.Poly(α-amino acid)-b-poly(tetrahydrofuran)-b-poly(α-amino acid)(PAA-PTHF-PAA)is one of the copolymers.In this contribution,di-hydroxyl-ended HO-PTHF-OH is transferred into di-oxyamino-ended H2NO-PTHF-ONH2 quantitatively,which is used as a macroinitiator to polymerize sarcosine N-thiocarboxyanhydride(Sar-NTA)and N-phenyoxycarbonyl N-ε-carbobenzyloxy-D-lysine(ZDL-NPC).Well-defined triblock PAA-NHO-PTHF-ONH-PAA is produced with high molecular weight(up to 25.3 kg/mol)and narrow dispersity.The amphiphilic PSar-NHO-PTHF-ONH-PSar(STS)self-assembles into micelles with uniform diameters of 30—40 nm according to DLS.Owing to oxygen amide groups inside the backbone of these copolymers,the polyether-poly(amino acid)s block copolymers are cleavable under an acidic environment and therefore have potential applications in smart biomedicine and engineering.展开更多
Chitosan-graft-poly（lactic acid） （CS-g-PLA） copolymer was synthesized through emulsion self-assembly in a water-in-oil （W/O） microemulsion. The water phase was composed of CS aqueous solution, while the oil phas...Chitosan-graft-poly（lactic acid） （CS-g-PLA） copolymer was synthesized through emulsion self-assembly in a water-in-oil （W/O） microemulsion. The water phase was composed of CS aqueous solution, while the oil phase was made up of PLA in chloroform. The W/O microemulsion was fabricated in the presence of surfactant span-80 and the self-assembly was performed between PLA and CS under the effect of N-（3-dimethylaminopropyl）-N＇ethylcarbodiimide hydrochloride （EDC＇HCI）. FTIR and IH-NMR analysis indicated PLA was grafted onto the backbone of CS via the reaction between the carboxyl groups in PLA and the amino groups in CS. 1H-NMR characterization further revealed the grafting content of PLA was 16%. The obtained CS-g-PLA could self-assemble to form micelles, their size distributed in the range of 125-375 nm with average diameter of 142 nm. The present design integrates the favorable biological properties of CS and the excellent mechanical properties of PLA, which makes CS-g-PLA copolymer a promising candidate as a carrier for targeted bioactive molecules delivery.展开更多
Three kinds of poly amino acids, poly-γ-glutamic acid, poly(ε-L-lysine) and multi-L-arginyl-poly (L-aspartic acid) can be synthesized by enzymatic process independently from ribosomal protein biosynthesis pathways i...Three kinds of poly amino acids, poly-γ-glutamic acid, poly(ε-L-lysine) and multi-L-arginyl-poly (L-aspartic acid) can be synthesized by enzymatic process independently from ribosomal protein biosynthesis pathways in microorganism. These biosynthesized polymers have attracted more and more attentions because of their unique properties and various applications. In this review, the current knowledge on the biosynthesis, biodegradations and applications of these three poly amino acids are summarized.展开更多
基金Project (21176264) supported by the National Natural Science Foundation of ChinaProject (11JJ2010) supported by Hunan Provincial Natural Science Foundation of ChinaProject (LC13076) supported by Undergraduate Innovation Foundation of Central South University,China
文摘Copolymer of maleic acid and acrylic acid （PMA-100）, combining with polyvinyl butyral （PVB） ultrafiltration membrane was used for the removal of Mn（II） from waste water by complexation-ultrafiltration. The carboxylic group content of PMA-100 and the rate of complexation reaction were measured. Effects of the mass ratio of PMA-100 to Mn（II） （n）, pH, background electrolyte, etc on the rejection rate （R） and permeate flux （J） were investigated. The results show that carboxylic group content of PMA-100 is 9.5 mmol/g. The complexation of Mn（II） with PMA-100 is rapid and completed within 5 min at pH 6.0. Both R and J increase with pH increasing in the range of 2.5-7.0, and R increases with the increase of n at pH 6.0 while J is little affected. The background electrolyte leads to the decrease of R, and CaCl2 has much greater effect on R than NaCl at the same ionic strength.
基金supported by the National Natural Science Foundation of China(Grant No.U23A20591,52203201,52173149,and 81971174)the Youth Talents Promotion Project of Jilin Province(Grant No.202019)+1 种基金the Science and Technology Development Program of Jilin Province(Grant No.20210101114JC)Research Cooperation Platform Project of Sino-Japanese Friendship Hospital of Jilin University and Basic Medical School of Jilin University(Grant No.KYXZ2022JC04).
文摘Neurological injury caused by ischemic stroke is a major cause of permanent disability and death. The currently available neuroprotective drugs fail to achieve desired therapeutic efficacy mainly due to short circulation half-life and poor blood−brain barrier (BBB) permeability. For that, an edaravone-loaded pH/glutathione (pH/GSH) dual-responsive poly(amino acid) nanogel (NG/EDA) was developed to improve the neuroprotection of EDA. The nanogel was triggered by acidic and EDA-induced high-level GSH microenvironments, which enabled the selective and sustained release of EDA at the site of ischemic injury. NG/EDA exhibited a uniform sub-spherical morphology with a mean hydrodynamic diameter of 112.3 ± 8.2 nm. NG/EDA efficiently accumulated at the cerebral ischemic injury site of permanent middle cerebral artery occlusion (pMCAO) mice, showing an efficient BBB crossing feature. Notably, NG/EDA with 50 µM EDA significantly increased neuron survival (29.3%) following oxygen and glucose deprivation by inhibiting ferroptosis. In addition, administering NG/EDA for 7 d significantly reduced infarct volume to 22.2% ± 7.2% and decreased neurobehavioral scores from 9.0 ± 0.6 to 2.0 ± 0.8. Such a pH/GSH dual-responsive nanoplatform might provide a unique and promising modality for neuroprotection in ischemic stroke and other central nervous system diseases.
文摘Biodegradable chitosan-g-poly (D, L-lactic acid) copolymers were prepared via two methods. (1) The lactide was grafted onto hydroxyl groups of chitosan by using macromolecular initiator sodium of trimethylsilyl-chitosan, (2) poly (D,L-lactic acid)(PLA) with low molecular weight can be linked to the amino group by coupling activated PLA to trimethylsilyl-chitosan. Two graft copolymers had hydrophilic-hydrophobic character and can be applied as carriers for drug delivery.
文摘A novel kind of copolymer with ABA-type block structure was synthesized by anionic ring-opening polymerization of beta-butyrolactone (beta-BL) in the presence of a PEG-based dicarboxylates as macroinitiators which were prepared by the esterification of aliphatic cyclic anhydride and poly(ethylene glycol) (PEG) oligomers (M-n = 2000, 4000 and 6000) and conversion of potassium dicarboxylates. The resultant copolymers as well as the intermediates were characterized by IR, H-1-NMR and GPC.
基金the National Metallurgical Laboratory,Jamshedpur for their kind support
文摘This study aims to beneficiate low grade goethitic iron ore fines using a selective flocculation process. Selective flocculation studies were conducted using different polymers such as starch amylopectin(AP), poly acrylic acid(PAA), and a graft copolymer(AP-g-PAA). The obtained results were analyzed; they indicate the enhancement of the iron ore grade from 58.49% to 67.52% using AP-g-PAA with a recovery of 95.08%. In addition, 64.45% Fe with a recovery of 88.79% was obtained using AP. Similarly, using PAA, the grade increased to 63.46% Fe with a recovery of 82.10%. The findings are also supported by characterizing concentrates using X-ray diffraction(XRD) and electron probe microanalysis(EPMA) techniques.
基金Funded by the National Natural Science Foundation of China (No.50873012)
文摘Poly[（alanino ethyl ester）0.67 （glycino ethyl ester）0.33 phosphazene] （PAGP） was synthesized, and morphology and diameter of the electrospun PAGP nanofibers were systematically evaluated by using a cool field emission scanning electron microscope （SEM） with changing the important processing variables such as applied voltage, polymeric concentration, and ambient temperature. The average diameter of PAGP nanofibers was inversely proportional to the applied voltage, but increased with the increase of solution concentration. Lower environmental temperature was unfavorable due to the nanofibers conglutination.
基金Supported by International Cooperation from Ministry of Science and Technology of China(No.2008DFA51170)
文摘Hydrophilic degraded gelatin was modified with hydrophobic poly(ε-caprolactone) (PCL) via a chemical grafting route.Firstly,PCL with one hydroxyl end group was prepared by the ring-opening polymerization of εcaprolactone (ε-CL) with tin (Ⅱ) 2-ethylhexanoate as catalyst and n-butyl alcohol as initiator.Secondly,the PCL reacted with isophorone diisocyanate (IPDI) to prepare PCL with isocyanate functional group (PCL-NCO).Hydroxylamine was used to degrade gelatin by the cleavage between asparagine and glycine residues of gelatin.PCL-NCO reacted with the hydroxyl/amino groups of degraded gelatin in a homogeneous system and yielded the PCL modified gelatin copolymers.The gelatin grafted PCL copolymers were measured by means of XRD,FTIR,DSC and 1 H NMR.The results confirmed the conjugation of PCL onto gelatin chains.The PCL modified gelatin can be used as biomaterials owing to their biocompatibility and biodegradation.
文摘In this study a low molecular weight triblock copolymer derived fromε-caprolactone and tetrahydrofuran was used as a non-reactive compatibilizer of immiscible PLA/PCL blends.Ternary blends with 0,1.5 wt%,3 wt%and 5 wt% copolymer and about 75 wt%PLA were prepared by single screw extrusion and characterized by scanning electron microscopy(SEM),differential scanning calorimetry(DSC),dynamic mechanical analysis(DMA),tensile and Izod impact testing.SEM micrographs showed that the size of the dispersed PCL domains was practically constant regardless of copolymer concentration.This result can be explained by the low shear rate employed during processing step and a decrease of PCL viscosity by presence of the triblock copolymer.However,when the copolymer concentration increased,strain at break of PLA/PCL blends also increased.PLA/PCL blend with 0 wt% copolymer presented 2%strain at break,whereas PLA/PCL blend with 5 wt%copolymer exhibited 90%.
基金Supported by Chinese Program for New Century Excellent Talents in University "NCET",Ministry of Education of P.R. China(No.2008DFA51170)
文摘A series of novel copolymers were successfully synthesized by ring-opening polymerization （ROP） of 3 （S）-methyl-morpholine-2,5-dione （MMD） and 5-methyl-5-benzyloxycarbonyl-1,3-dioxan-2-one （MBC） using stan- nous octoate as catalyst. The copolymers were characterized by means of ~H-NMR and FT-IR spectroscopy. Gel permeation chromatography （GPC） test shows that the average-number relative molecular mass and average-weight rela- tive molecular mass slightly increase with the increase of MBC content in feed. The results of differential scanning calorimetry （DSC） demonstrate that the glass transition temperature of copolymers increases with the increase of MBC content in copolymers. The copolymers of MMD and MBC are amorphous copolymers, as indicated by DSC results, while the homopolymer of MMD is semicrystalline.
基金supported by the Joint Foundation of Shaanxi Province Natural Science Basic Research Program and Shaanxi Coal Chemical Group Cov Ltd.(No.2019JLM-46)the National Natural Science Foundation of China(No.21674091).
文摘Main observation and conclusion Block copolymers not only combine properties of different segments but also generate new application prospects.Poly(α-amino acid)-b-poly(tetrahydrofuran)-b-poly(α-amino acid)(PAA-PTHF-PAA)is one of the copolymers.In this contribution,di-hydroxyl-ended HO-PTHF-OH is transferred into di-oxyamino-ended H2NO-PTHF-ONH2 quantitatively,which is used as a macroinitiator to polymerize sarcosine N-thiocarboxyanhydride(Sar-NTA)and N-phenyoxycarbonyl N-ε-carbobenzyloxy-D-lysine(ZDL-NPC).Well-defined triblock PAA-NHO-PTHF-ONH-PAA is produced with high molecular weight(up to 25.3 kg/mol)and narrow dispersity.The amphiphilic PSar-NHO-PTHF-ONH-PSar(STS)self-assembles into micelles with uniform diameters of 30—40 nm according to DLS.Owing to oxygen amide groups inside the backbone of these copolymers,the polyether-poly(amino acid)s block copolymers are cleavable under an acidic environment and therefore have potential applications in smart biomedicine and engineering.
基金financially supported by the National Natural Science Foundation of China(Nos.11272038,50803032,11032012,10925208,11202017 and 11120101001)the Fundamental Research Funds for the Central Universities(No.YWF-13-T-RSC-024)+2 种基金the 111 Project(No.B13003)the International Joint Research Center of Aerospace Biotechnology and Medical Engineering,Ministry of Science and Technology of Chinathe Program of Pearl River Young Talents of Science and Technology in Guangzhou,China(No.2013Z2200010)
文摘Chitosan-graft-poly（lactic acid） （CS-g-PLA） copolymer was synthesized through emulsion self-assembly in a water-in-oil （W/O） microemulsion. The water phase was composed of CS aqueous solution, while the oil phase was made up of PLA in chloroform. The W/O microemulsion was fabricated in the presence of surfactant span-80 and the self-assembly was performed between PLA and CS under the effect of N-（3-dimethylaminopropyl）-N＇ethylcarbodiimide hydrochloride （EDC＇HCI）. FTIR and IH-NMR analysis indicated PLA was grafted onto the backbone of CS via the reaction between the carboxyl groups in PLA and the amino groups in CS. 1H-NMR characterization further revealed the grafting content of PLA was 16%. The obtained CS-g-PLA could self-assemble to form micelles, their size distributed in the range of 125-375 nm with average diameter of 142 nm. The present design integrates the favorable biological properties of CS and the excellent mechanical properties of PLA, which makes CS-g-PLA copolymer a promising candidate as a carrier for targeted bioactive molecules delivery.
基金Supported by the Ministry of Science and Technology (Grant No. 2006AA02Z239)
文摘Three kinds of poly amino acids, poly-γ-glutamic acid, poly(ε-L-lysine) and multi-L-arginyl-poly (L-aspartic acid) can be synthesized by enzymatic process independently from ribosomal protein biosynthesis pathways in microorganism. These biosynthesized polymers have attracted more and more attentions because of their unique properties and various applications. In this review, the current knowledge on the biosynthesis, biodegradations and applications of these three poly amino acids are summarized.
