Constructing a stable interface on Ni-rich LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) cathode via lactic acid-assisted engineering strategy

Ni-rich layered oxides are potential cathode materials for next-generation high energy density Li-ion batteries due to their high capacity and low cost.However,the inherently unstable surface properties,including high levels of residual Li compounds,dissolution of transition metal cations,and parasitic side reactions,have not been effectively addressed,leading to significant degradation in their electrochemical performance.In this study,we propose a simple and effective lactic acid-assisted interface engineering strategy to regulate the surface chemistry and properties of Ni-rich LiNi_(0.8)Co_(0.1)Mr_(0.1)O_(2) cathode.This novel surface treatment method successfully eliminates surface residual Li compounds,inhibits structural collapse,and mitigates cathode-electrolyte interface film growth.As a result,the lactic acidtreated LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) achieved a remarkable capacity retention of 91.7% after 100 cycles at 0.5 C(25℃) and outstanding rate capability of 149.5 mA h g^(-1) at 10 C,significantly outperforming the pristine material.Furthermore,a pouch-type full cell incorporating the modified LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2) cathode demonstrates impressive long-term cycle life,retaining 81.5% of its capacity after 500 cycles at 1 C.More importantly,the thermal stability of the modified cathode is also dramatically improved.This study offers a valuable surface modification strategy for enhancing the overall performance of Ni-rich cathode materials.

Poly(lactic acid)-aspirin microspheres prepared via the traditional and improved solvent evaporation methods and its application performances

Drug-loaded microspheres are significant for the development of modern pharmaceutical products. It is well known that the taken of aspirin for long-term increases the risk of serious gastrointestinal complications, therefore a controllable delivery of aspirin is of importance to lighten those side effects. In this work, poly(lactic acid)(PLA) was chosen as the carrier to prepare PLA-aspirin microspheres by using the traditional and the improved solvent evaporation methods. It was found that no matter which experimental condition was, the encapsulation efficiency of aspirin was higher by using the improved method than that of the traditional method. Specifically, when the concentration of polyvinyl alcohol = 1%(mass),the polymer concentration = 1:20, the oil/water rate = 1:2.5, PLA-aspirin microspheres were obtained via the improved method with a high yield of 82.83%(mass) and an encapsulation efficiency of 44.09%. PLAaspirin microspheres were then prepared continuously using the improved method, which further enhanced the encapsulation efficiency to 54.56%. Approximate 85% aspirin released from microspheres within 7 days. Obvious degradation which was represented by reduction on hardness was observed by soaking microspheres in PBS for 60 days. This work is of interest because it provides a continuous route to prepare PLA-aspirin microspheres continuously with a high drug encapsulation efficiency.

Allergen degradation of bee pollen by lactic acid bacteria fermentation and its alleviatory effects on allergic reactions in BALB/c mice

Food allergy as a global health problem threatens food industry.Bee pollen(BP)is a typical food with allergenic potentials,although it performs various nutritional/pharmacological functions to humans.In this study,lactic acid bacteria(LAB)were used to ferment Brassica napus BP for alleviating its allergenicity.Four novel allergens(glutaredoxin,oleosin-B2,catalase and lipase)were identified with significant decreases in LAB-fermented BP(FBP)than natural BP by proteomics.Meanwhile,metabolomics analysis showed significant increases of 28 characteristic oligopeptides and amino acids in FBP versus BP,indicating the degradation of LAB on allergens.Moreover,FBP showed alleviatory effects in BALB/c mice,which relieved pathological symptoms and lowered production of allergic mediators.Microbial high-throughput sequencing analysis showed that FBP could regulate gut microbiota and metabolism to strengthen immunity,which were closely correlated with the alleviation of allergic reactivity.These findings could contribute to the development and utilization of hypoallergenic BP products.

Preparation of lactic acid bacteria compound starter cultures based on pasting properties and its improvement of glutinous rice flour and dough

The effects of 5 lactic acid bacteria(LAB)fermentation on the pasting properties of glutinous rice flour were compared,and suitable fermentation strains were selected based on the changes of viscosity,setback value,and breakdown value to prepare LAB compound starter cultures.The results revealed that Latilactobacillus sakei HSD004 and Lacticaseibacillus rhamnosus HSD005 had apparent advantages in increasing the viscosity and reducing the setback and breakdown values of glutinous rice flour.In particular,the compound starter created using the two abovementioned LAB in the ratio of 3:1 had better performance than that using a single LAB in improving the pasting properties and increasing the water and oil absorption capacity of glutinous rice flour.Moreover,the gelatinization enthalpy of the fermented samples increased significantly.For frozen glutinous rice dough stored for 28 days,the viscoelasticity of frozen dough prepared by compound starter was better than that of control dough,and the freezable water content was lower than that of control dough.These results indicate that compound LAB fermentation is a promising technology in the glutinous rice-based food processing industry,which has significance for its application.

Application of Next Generation Sequencing for Rapid Identification of Lactic Acid Bacteria

The rapid identification of lactic acid bacteria,which are essential microorganisms in the food industry,is of great significance for industrial applications.The identification of lactic acid bacteria traditionally relies on the isolation and identification of pure colonies.While this method is well-established and widely used,it is not without limitations.The subjective judgment inherent in the isolation and purification process introduces potential for error,and the incomplete nature of the isolation process can result in the loss of valuable information.The advent of next generation sequencing has provided a novel approach to the rapid identification of lactic acid bacteria.This technology offers several advantages,including rapidity,accuracy,high throughput,and low cost.Next generation sequencing represents a significant advancement in the field of DNA sequencing.Its ability to rapidly and accurately identify lactic acid bacteria strains in samples with insufficient information or in the presence of multiple lactic acid bacteria sets it apart as a valuable tool.The application of this technology not only circumvents the potential errors inherent in the traditional method but also provides a robust foundation for the expeditious identification of lactic acid bacteria strains and the authentication of bacterial powder in industrial applications.This paper commences with an overview of traditional and molecular biology methods for the identification of lactic acid bacteria.While each method has its own advantages,they are not without limitations in practical application.Subsequently,the paper provides an introduction of the principle,process,advantages,and disadvantages of next generation sequencing,and also details its application in strain identification and rapid identification of lactic acid bacteria.The objective of this study is to provide a comprehensive and reliable basis for the rapid identification of industrial lactic acid bacteria strains and the authenticity identification of bacterial powder.

Edaravone-loaded poly(amino acid) nanogel inhibits ferroptosis for neuroprotection in cerebral ischemia injury

Neurological injury caused by ischemic stroke is a major cause of permanent disability and death. The currently available neuroprotective drugs fail to achieve desired therapeutic efficacy mainly due to short circulation half-life and poor blood−brain barrier (BBB) permeability. For that, an edaravone-loaded pH/glutathione (pH/GSH) dual-responsive poly(amino acid) nanogel (NG/EDA) was developed to improve the neuroprotection of EDA. The nanogel was triggered by acidic and EDA-induced high-level GSH microenvironments, which enabled the selective and sustained release of EDA at the site of ischemic injury. NG/EDA exhibited a uniform sub-spherical morphology with a mean hydrodynamic diameter of 112.3 ± 8.2 nm. NG/EDA efficiently accumulated at the cerebral ischemic injury site of permanent middle cerebral artery occlusion (pMCAO) mice, showing an efficient BBB crossing feature. Notably, NG/EDA with 50 µM EDA significantly increased neuron survival (29.3%) following oxygen and glucose deprivation by inhibiting ferroptosis. In addition, administering NG/EDA for 7 d significantly reduced infarct volume to 22.2% ± 7.2% and decreased neurobehavioral scores from 9.0 ± 0.6 to 2.0 ± 0.8. Such a pH/GSH dual-responsive nanoplatform might provide a unique and promising modality for neuroprotection in ischemic stroke and other central nervous system diseases.

Corrosion resistance of Zn-AI layered double hydroxide/ poly（lactic acid） composite coating on magnesium alloy AZ31

A Zn-AI layered double hydroxide （ZnAI-LDH） coating consisted of uniform hexagonal nano-plates was firstly synthesized by co-precipitation and hydrothermal treatment on the AZ31 alloy, and then a poly（lactic acid） （PLA） coating was sealed on the top layer of the ZnAI-LDH coating using vacuum freeze-drying. The characteristics of the ZnAI-LDH/PLA composite coatings were investigated by means of XRD, SEM, FTIR and EDS. The corrosion resistance of the coatings was assessed by potentiodynamic polarization and electrochemical impedance spectroscopy （EIS）. The results showed that the ZnAI-LDH coating contained a compact inner layer and a porous outer layer, and the PLA coating with a strong adhesion to the porous outer layer can prolong the service life of the ZnAI-LDH coating. The excellent corrosion resistance of this composite coating can be attributable to its barrier function, ion-exchange and self-healing ability.

Mechanical and Morphological Properties of Wood Plastic Biocomposites Prepared from Toughened Poly（lactic acid） and Rubber Wood Sawdust （Hevea brasiliensis）

The present research aims to utilize the acrylic Core-Shell Rubber （CSR） particles to reduce the brittleness in Wood Plastic Composites （WPC） prepared from poly（lactic acid） （PLA） and rubber wood sawdust （Hevea brasiliensis）. Experimental works consisted of two major parts. The first part concentrated on toughening PLA by using CSR particles. Mechanical tests revealed that PLA had become tougher with a more than five times increment in the impact strength when the CSR was added at only 5 wt%. The modified PLA was less stiff with the significant reductions of both elastic and flexural moduli and strengths. The second part focused on producing WPC from the toughened PLA and rubber wood sawdust. The tensile moduli and the strengths of the PLA composites increased with rubber wood content. The composites turned out to be more brittle with reductions of both the impact strength and the tensile elongation at break at all the sawdust contents. Toughening PLA/wood flour with 5 wt% CSR improved both the impact strength and the tensile elongation at break. The toughness enhancement was also depicted by the plastic deformation observed on the surfaces of fractured PLA/CSR/wood sawdust composites.

Blends of Poly(lactic acid) with Thermoplastic Acetylated Starch

Blends of poly（lactic acid）（PLA） and thermoplastic acetylated starch（ATPS） were prepared by means of the melt mixing method. The results show that PLA and ATPS were partially miscible, which was confirmed with the measurement of Tg by dynamic mechanical analysis（DMA） and differrential scanning calorimetry（DSC）. The mechanical and thermal properties of the blends were improved. With increasing the ATPS content, the elongation at break and impact strength were increased. The elongation at break increased from 5% of neat PLA to 25% of the blend PLA/ATPS40. It was found that the cold crystallization behavior of PLA changed evidently by addition of ATPS. The cold crystallization temperature（Tcc） of each of PLA/ATPS blends was found to shift to a lower temperature and the width of exothermic peak became narrow compared with that of neat PLA. The thermogravimetry analysis（TGA） results showed that the peak of derivative weight for ATPS moved to higher temperature with increasing PLA content in PLA/ATPS blends. It can be concluded that PLA could increase the thermal stability of ATPS. The rheological measurement reveals the melt elasticity and viscosity of the blends decreased with the increased concentration of ATPS, which was favorable to the processing properties of PLA.

Effect of DOPO-containing Flame Retardants on Poly（lactic acid）： Non-flammability, Mechanical Properties and Thermal Behaviors

The flame retardancies of three kinds of 9,10-dihydro-9-oxa-10-phosphaphenan-threne 10-oxide（DOPO）- containing flame retardant（A1, A2, A3）/poly（lactic acid）（PLA） composites[PA-n/（Ax-y）, n= 1--12; x= l, 2, 3, denoting three kinds of flame retardants; y= 10%, 20%, 30%, 40%, denoting the mass fraction of Ax] were greatly enhanced by melt blending of flame retardant Ax with PLA, including twin-screw extrusion and injection-molding processes. With only 10%（mass fraction） of Ax added to PLA, good flame retardancy with limiting oxygen index（LOI） values of more than 33% was achieved. As the Ax mass fraction was further increased to 20%, PA-n/（Ax-20%） composites showed much better flame retardancy（LOI~〉35% and UL-94 V-0 rating）. Moreover, the thermal degradation behaviors and mechanical properties of PA-n/（Ax-y） composites were investigated via thermogravimetric analysis（TGA）, differen- tial thermal analysis（DTA）, tensile testing, notched impact-bar testing, and dynamic mechanical analysis（DMA）. TGA results show that PA-n/（Ax-y） composites have slower rate of mass loss and much higher char yield, compared to neat PLA. With the addition of Ax to PLA, the DTA and DMA results indicate slight variations in glass transition tcmpe- ratures（Tg） of PA-n/（Ax-y） composites. Based on TGA results under nonisothermal conditions, the thermal degrada- tion kinetics of PA-n/（Ax-y） composites were studied by KAssinger＇s and Ozawa＇s methods. These thermal degrada- tion dynamic analyses show lower activation energies（EK or Eo） for PA-n/（Ax-y） composites, corresponding to higher mass fractions of Ax（from 10% to 40%）. The PA-n/（Ax-y） composites with good flame retardancy and good mecha- nical properties obtained in this study could be potential candidates for fire- and heat-resistant applications in auto- motive engineering and building fields with more safety and excellent performance.

Comparison of morphological and functional outcomes of mouse sciatic nerve repair with three biodegradable polymer conduits containing poly (lactic acid)

Poly（lactic acid）（PLA）-containing nerve guidance conduits（NGCs） are currently being investigated for nerve repair as an alternative to autograft, which leads to permanent functional impairment in the territory innervated by the removed nerve. Combination of polymers modifies the physical properties of the conduits, altering their nerve-guidance properties. Conduits made from PLA-only or combined with other polymers have been used successfully for nerve repair, but their efficiency has not been compared. We compared the morphological and functional outcomes of peripheral nerve repair by using NGCs made of poly（lactic acid） and combined or not with polycaprolactone（PLA/PCL） or polyvinylpyrrolidone（PLA/PVP）. To assess the functional recovery, we employed a mechanical hyperalgesia analysis, sciatic functional index（SFI）, and electroneuromyography. The mechanical hyperalgesia analysis showed that the PLA group improved more rapidly than the PLA/PVP and PLA/PCL groups; similarly, in the electroneuromyography assay, the PLA group exhibited higher amplitude than the PLA/PCL and PLA/PVP groups. However, the SFI improvement rates did not differ among the groups. Morphologically, the PLA group showed more vascularization, while the nerve fiber regeneration did not differ among the groups. In conclusion, the PLA-only conduits were superior to the other NGCs tested for nerve repair.

Melt Synthesis and Characterization of Poly(L-lactic Acid) Chain Linked by Multifunctional Epoxy Compound

High molecular weight（Mw） poly（L-lactic acid）s（PLLAs） were synthesized using multifunctional epoxy compound（Joncryl-ADR4370） as chain extender. The products were characterized by gel permeation chromatography（GPC） and spectroscopy（1HNMR and FTIR）. The results indicated that the Mw of PLLA increased with the increasing of the ratio of epoxy compound and the extending of reaction time. The highest Mw of PLLA reached 360 000 g/mol when the ratio of epoxy compound was 1.5 wt%. However, the reactants turned to cross-linking when the ratio of epoxy compound was over 1.5 wt%. Differential scanning calorimetry（DSC） measurements demonstrated that the glass transition（Tg） and melting temperatures（Tm） of products increased slightly as the increase of the molecular weight. Analysis of the hydrolytic degradation in vitro showed that the branched PLLA possessed the quicker degradability than that of the linear PLLA.

Preparation and phase change performance of Na_2HPO_4·12H_2O@poly(lactic acid) capsules for thermal energy storage

Micro-encapsulated phase-change materials(micro PCMs) with Na_2 HPO_4·12 H_2 O encapsulated in poly(lactic acid)(PLA) shell were prepared by a solvent evaporation–precipitation method that involves the use of a coaxial needle. The effects of PLA concentration, stirring speed, injection rate of core and shell solutions, and polyvinyl alcohol(PVA) concentration on phase change properties were investigated. The thermal properties of microP CMs were characterized by differential scanning calorimetry(DSC). The capsules prepared under the optimal conditions are about 2 mm in diameter and show a latent heat of up to 122.2 J·g^(-1).

Synthesis of the Biomimetic Polymer: Aliphatic Diamine and RGDS Modified Poly(d,l-lactic acid)

A novel poly（d, /-lactic acid） （PDLLA） based biomimetic polymer was synthesized by grafting maleic anhydride, butanediamine and arg-gly-asp-ser （RGDS） peptides onto the backbone of PDLLA, aiming to overcome the acidity and auto-accelerating degradation of PDLLA during degradation and to improve its biospecificity and biocompatibility. The synthetic copolymer was characterized by FTIR, ^13C NMR and amino acid analyzer （AAA）.

Lactic Acid Inhibits NF-kB Activation by Lipopolysaccharide in Rat Intestinal Mucosa Microvascular Endothelial Cells

To investigate whether lactic acid could inhibit the LPS-activation of NF-κB p65 in rat intestinal mucosa microvascular endothelial cells （RIMMVECs）, RIMMVECs, cultured in vitro, were pretreated with different concentrations of lactic acid and then exposed to lipopolysaccharide （LPS）. Cells and cell culture media were then collected at different time intervals. Production of tumor necrosis factor-a （TNF-a） and interleukin-6 （IL-6） was examined at the protein level by enzyme-linked immunosorbent assay. The influence of lactic acid on the LPS-activation of NF-κB was examined at mRNA and protein levels by real-time quantitative PCR and Western blot analysis, respectively. TNF-a and IL-6 protein levels were significantly decreased after pretreatment with lactic acid compared with cells exposed to LPS only. After pretreatment with 7.5, 5.0, and 2.5 μL mL-1 lactic acid, NF-κB mRNA levels were increased by 1.51-, 2.62- and 3.00-fold, respectively, compared with levels in control cells without LPS treatment. Western blot analysis indicated that the level of NF-κB p65 in the lactic acid-pretreated group was significantly lower than that in the group treated with LPS only （positive control） and was unchanged compared with the group without LPS treatment （blank control）. These results suggest that lactic acid may inhibit LPS-activation of NF-κB, leading to the down-regulation of TNF-a and IL-6.

Preparation and properties of short natural fiber reinforced poly(lactic acid) composites

The natural fiber/poly(lactic acid) (PLA) composites were prepared with ramie and jute short fiber as reinforcement and PLA as matrix. The mechanical and thermal properties of the composites were investigated. The results show that the properties of the composites are better than those of plain PLA. When the content of the fiber is 30%, the composites can get the best mechanical properties. The dynamic mechanical analysis results show that the storage moduli of the PLA/ramie and PLA/jute composites increase with respect to the plain PLA. The Vicat softening temperature of the composites is greatly higher than that of PLA. The results of thermogravimetric analysis show that adding fiber to the PLA matrix can improve the degradation temperature of PLA.

Synergistic effect of MXene on the flame retardancy and thermal degradation of intumescent flame retardant biodegradable poly(lactic acid)composites

The effect of Ti3C2 MXene nanosheets on the intumescent flame retardant(IFR)poly(lactic acid)(PLA)composites was investigated among a series of PLA/IFR/MXene,which were prepared by melt blending 0-2.0 wt%MXene,10.0 wt%-12.0 wt%IFR and PLA together.The results of limiting oxygen index(LOI)and vertical burning(UL-94)discover that the combination of 0.5 wt%MXene and 11.5 wt%IFR synergistically improves the fire safety of PLA to reach UL-94 V-0 rating with LOI value of 33.0%.The PLA/IFR/MXene composites perform an obvious reduction in peak of heat release rate(HRR)in cone calorimeter tests(CCTs).Furthermore,the carbon residues after CCTs were characterized by scanning electron microscope(SEM),laser Raman spectroscopy(LRS),X-ray diffraction(XRD)and X-ray photoelectron spectroscopy(XPS).It is demonstrated that both the titanium composition of the MXene structure and the characteristics of the two-dimensional material enhance the PLA/IFR/MXene composite materials’ability to produce a dense barrier layer to resist burnout during thermal degradation.

A novel artificial nerve graft for repairing longdistance sciatic nerve defects:a self-assembling peptide nanofiber scaffold-containing poly (lactic-co-glycolic acid) conduit

In this study, we developed a novel artificial nerve graft termed self-assembling peptide nanofiber scaffold （SAPNS）-containing poly（lactic-co-glycolic acid） （PLGA） conduit （SPC） and used it to bridge a 10-mm-long sciatic nerve defect in the rat. Retrograde tracing, behavioral testing and histomorphometric analyses showed that compared with the empty PLGA conduit implantation group, the SPC implantation group had a larger number of growing and extending axons, a markedly increased diameter of regenerated axons and a greater thickness of the myelin sheath in the conduit. Furthermore, there was an increase in the size of the neuromuscular junction and myofiber diameter in the target muscle. These findings suggest that the novel artificial SPC nerve graft can promote axonal regeneration and remyelination in the transected peripheral nerve and can be used for repairing peripheral nerve injury.