Quantitative lithium substitution of carboxyl hydrogens in polyacrylic acid binder enables robust SiO electrodes with durable lithium storage stability

The design of advanced binders plays a critical role in stabilizing the cycling performance of large-volume-effect silicon monoxide(SiO)anodes.For the classic polyacrylic acid(PAA)binder,the self-association of-COOH groups in PAA leads to the formation of intramolecular and intermolecular hydrogen bonds,greatly weakening the bonding force of the binder to SiO surface.However,strengthening the binder-material interaction from the perspective of binder molecular regulation poses a significant challenge.Herein,a modified PAA-Li_(x)(0.25≤x≤1)binder with prominent mechanical properties and adhesion strength is specifically synthesized for SiO anodes by quantitatively substituting the carboxylic hydrogen with lithium.The appropriate lithium substitution(x=0.25)not only effectively increases the number of hydrogen bonds between the PAA binder and SiO surface owing to charge repulsion effect between ions,but also guarantees moderate entanglement between PAA-Li_x molecular chains through the ion-dipole interaction.As such,the PAA-Li_(0.25)/SiO electrode exhibits exceptional mechanical properties and the lowest volume change,as well as the optimum cycling(1237.3 mA h g^(-1)after 100cycles at 0.1 C)and rate performance(1000.6 mA h g^(-1)at 1 C),significantly outperforming the electrode using pristine PAA binder.This work paves the way for quantitative regulation of binders at the molecular level.

Synthesis and Properties of an AMPS-Modified Polyacrylic Acid Superplasticizer

A 2-acrylamide-2-methyl propylene sodium sulfonic （AMPS）-modified polyacrylic acid superplasticizer was synthesized using aqueous solution polymerization with the major monomers including the self-made active macromers polyethylene glycol mono-methyl ether acrylate acrylic （MPEGAA）, acrylic acid （AA）, AMPS, and sodium methyl allyl sulfonate （SMAS）. The ratios of the monomers were determined using an orthogonal experiment. This research focused on the effects of the dosages of different macromers, the polymerization conditions, and the length of MPEGAA side chains on the properties of the AMPS-modified polyacrylic acid super-plasticizer. The best polymerization conditions of the AMPS-modified polyacrylic acid superplasticizer are when （n（MPEGAA）：n（SMAS）：n（AMPS）：n（AA） equals 0.1：0.1：0.2：0.65, the molecular weight of monomethoxypolyethylene glycol is 1 200, the initiator ammonium persulfate accounts for 5% of the total mass of the polymerized monomers, the polymerization temperature is 80 ~C, and the reaction time is 4 h. The AMPS-modified polyacrylic acid superplasticizer synthesized in the best conditions exhibited excellent dispersivity and dispersion retainability. When the dosage ratio was 0.24%, the initial fluidity was 400 mm and the fluidity had nearly no loss after 1 h.

Synthesis of a Macromer, MPEGAA, Used to Prepare an AMPS-modified Polyacrylic Acid Superplasticizer

A macromer, methoxypolyethylene glycol acrylate （MPEGAA）, was synthesized by direct esterification using methoxypolyethylene glycol （MPEG-1200） and acrylic acid （AA） as the main materials. MPEGAA was then used to prepare a polyacrylic acid superplasticizer modified with 2-acrylamido-2- methylpropane sulfonic acid （AMPS）. A single-factor test was performed to investigate the effects of the molar ratio of acid to alcohol （n（AA）/n（MPEG））, inhibitor amount, catalyst amount, temperature, and time of esterification on the synthesis of MPEGAA. The experimental results showed that the optimal esterification conditions were as follows： n（AA）/n（MPEG）, 3.5：1; amount of hydroquinone （as an inhibitor）, 1.2%; amount of para-toluenesulfonic acid （as a catalyst）, 5.5%; reaction temperature, 95 ~C; and reaction time, 6 h. The AMPS- modified polyacrylic acid superplasticizer prepared under the optimal esterification conditions enabled the achievement and maintenance of high cement dispersibility. At an admixture amount of 0.15%, the cement paste fluidity was initially as high as 300 mm, and then decreased to 315 mm after 1 h and to 290 mm after 2 h.

The Synthesis Technique of Polyacrylic Acid Superplasticizer

Using water separation technique,acrylic acid （AA） and polyethylene glycol （PEG） 1000,of which the ratio was 1.5,were esterified and the optimum esterification ratio of 90% could be reached under the condition of 110 ℃×3 h.Using polyoxyethylene acrylate macromonomer （PA） prepared in the esterification,AA and sodium methylacryl sulfonate （MAS） as monomers,a copolymer which could be used as superplasticizer was prepared by free radical coolymerization in n（PA）：n（AA）：n（MAS） of 1：7：3.When the synthesis condition was 80 ℃× 5 h,the optimal dosage of initiator was 3.0%-4.0%,the fluidity of cement paste with the samples could reach 270 mm.By analyzing the effect of the content of residual small molecule sulfonic monomer on the properties of sample,n（MAS）/n（PA） was controlled in a range of 2.5-3.8.

Effects of an AMPS-Modified Polyacrylic Acid Superplasticizer on the Performance of Cement-based Materials

A self-made AMPS-modified polyacrylic acid superplasticizer and two others of the same type but with different molecular structures, which are commercially available, are used in this study to investigate the effect of a 2-acrylamide-2-methyl propylene sulfonic （AMPS）-modified polyacrylic acid superplasticizer on the properties of cement-based materials. In the experiments, initial fluidity, 1 and 2 h fluidity over time after admixtion, bleeding rate of the net cement mortar, and adsorption capacity and rate of cement particles are determined by adding different dosages of the three superplasticizers into the cement paste to characterize the dispersivity and the dispersion retention capability of each superplasticizer. Water-reducing rates of three kinds of mortars are simultaneously determined to characterize the water-reducing capacity of each superplasticizer, as well as the 3 and 28 d compressive strengths to characterize the compression resistance. Results show that water-reducing effect and fluidity better maintain the capability of the AMPS-modified polyacrylic acid superplasticizer than the two commercially available polyacrylic acid superplasticizers, and the compressive strengths after 3 and 28 d show significant growth. In conclusion, the effects of water reduction and strengthening of the AMPS-modified polyacrylic acid superplasticizer are evidently better than those of the two commercially available polyacrylic acid superplasticizers.

Effect of Molecular Structure on the Performance of Polyacrylic Acid Superplasticizer

The effects of structure parameters, such as molecular structure, segment kinds, molecular weight, and organic functional groups, on the performance of polyacrylic acid superplasticizer were discussed. According to the differences of chain sections, functional groups, eic, polyacrylic acid superplasticizer could be divided into A, B, C three parts. Among them, A chain section included sulfonic acid groups, B chain section carboxyl groups, C chain section polyester. Polyacrylic acid superplasticizers with different matching of A, B, C chain sections, different length of C chain section and different molecular weights were synthesized by acrylic acid, polyethylene glycol, sodium methyl allylsulfonate; the relation between the molecular structure and perfolxnance was also studied. The expetimental results indicate that the water-reduction ratio increases obviously with the increment of the proportion of sodium methyl allylsulfonate chain section in the molecular; the slump retention increases greatly with the increment of the proportion of acrylic acid chain section; the dispersion of cement particles increases with the increment of the chain length of polyethylene glycol; when the molecular weight is in the range of 5000, the dispersion and slump retentibity increase with the increment of the average molecular weight of polymers.

A new approach for development of vaccine against visceral leishmaniasis: Lipophosphoglycan and polyacrylic acid conjugates

Objective: To determine the antileishmanial vaccine effectiveness of lipophosphoglycan(LPG) and polyacrylic acids(PAA) conjugates on in vivo mice models.Methods: LPG molecule was isolated and purified from large-scale Leishmania donovani parasite culture. Protection efficacies of LPG alone, in combination with Freund's adjuvant, in a physical mixture and in conjugate(consisting of various LPG concentrations) with PAA, were comparatively determined by various techniques, such as cultivation with the micro-culture method, assessment of in vitro infection rates of peritoneal macrophages, determination of parasite load in liver with Leishman-Donovan Units, and detection of cytokine responses.Results: Obtained results demonstrated that the highest vaccine-mediated immune protection was provided by LPG-PAA conjugate due to all parameters investigated. According to the Leishman-Donovan Units results, the sharpest decline in parasite load was seen with a ratio of 81.17% when 35 mg LPG containing conjugate was applied. This value was 44.93% for the control group immunized only with LPG. Moreover, decreases in parasite load were 53.37%, 55.2% and 65.8% for the groups immunized with 10 mg LPG containing LPG-PAA conjugate, a physical mixture of the LPG–PAA, and a mixture of LPG + Freund's adjuvant, respectively. Furthermore, cytokine results supported that Th1 mediated protection occurred when mice were immunized with LPG-PAA conjugate.Conclusions: It has been demonstrated in this study that conjugate of LPG and PAA has an antileishmanial vaccine effect against visceral leishmaniasis. In this respect, the present study may lead to new vaccine approaches based on high immunogenic LPG molecule and adjuvant polymers in fighting against Leishmania infection.

The Humidity Sensor Using the Polyacrylic Emulsion Containing Magnesium Chloride

An impedance type humidity sensor based on the polyacrylic emulsion containing magnesium chloride (MgCl_2) without chemical modification was investigated.The impedances of the sensor were measured from various relative humidity in the frequency range between 0.1kHz and 100 kHz.The sensor has a good sensitivity from 60%RH to 90%RH.According to the experimental results,the response time is about 240 seconds in the adsorption process and 310 seconds in the desorption process.

IN SITU INTERFEROMETRIC STUDY ON THE GELATION PROCESS OF POLYACRYLIC ACID GELS

In situ interferometry was used to investigate the gelation process of polyacrylic acid (PAA) gels. The basic principle of the in situ interferometry technique is illustrated. It can give sufficient information for non-destructive and successful investigation of the whole gelation process. The effect of initiator concentration on the gelation process was studied. The polymerization rate of AA increases with increasing initiator concentration. The error arising from the thermal effect in the gelation process can be neglected.

Radiation synthesis and characterization of polyacrylic acid hydrogels

The pH-sensitive polyacrylic acid (PAA) hydrogels were synthesized by gamma-ray irradiation at an am- bient temperature. The influences of dose, monomer concentration, cross-linking agent content, pH, and ionic strength on the swelling ratio (SR) of the PAA hydrogels were investigated in detail. The results show that the SR of the hy- drogel decreases with an increase in the dose, monomer concentration, and cross-linking agent content. In alkaline so- lution, the SR of the hydrogels is much higher than that in acid solution. Also, the ionic strength can influence the SR of the hydrogels. The more the concentration, the lower the

Dynamic Behavior and Mass Transport in Polyacrylic Acid Gel by Dynamic Light Scattering

Dynamic behaviors on polyacrylic acid (PAA) gels and mass (small molecules) transports in the gels have been studied mainly by dynamic light scattering (DLS). The cross-linking degree (fc), monomer concentration (Cm) and temperature of the gels have significant influences on its dynamic behavior and mass transport in the gels. The increase of fc leads to decrease of the mesh sizes of the gels, thus the obstacle of the gels for mass transport is increased. As a result, small molecular diffusion Dk in the gels is decreased. So even if for small molecules, the Dk also is influenced.

Effects of an AMPS-modified Polyacrylic Acid Superplasticizer on the Performance of Concrete Materials

A self-made 2-acrylamide-2-methyl propylene sulfonic （AMPS）-modified polyacrylic acid superplasticizer and two other commercially available superplasticizers with different molecular structures are used in this study to investigate the effect of an AMPS-modified polyacrylic acid superplasticizer on the properties of concrete materials. In the experiments, initial and 1.5 h slumps over time after admixtion are determined by adding different dosages of three superplasticizers into the premixed concrete to characterize the slump loss resistance of the premixed concrete. The water-reducing rates of three different types of concrete are determined to characterize the water-reducing capacity of the concrete with each superplasticizer. The 3, 7 and 28 d compressive strength is determined to characterize the mechanical properties of the concrete with each superplasticizer. In the meanwhile, 1, 1.5 and 2.0 h slump loss rates over time after admixtion are determined by adding different dosages of the three superplasticizers into the high-performance concrete （HPC） to characterize the slump loss resistance of HPC. The 7, 28, 60 and 90 d compressive strength is determined to characterize the compressive properties of HPC with each superplasticizer. The dry shrinkage rates of three different types of HPC are determined with each superplasticizer. Electric flux after standard curing for 56 d and chloride ion diffusion coefficient after curing for 28 d of I-IPC are determined to characterize the impermeability of HPC with each superplasticizer. The cross-section was examined using a scanning electron microscopy （SEM） system. Results demonstrate that the AMPS-modified polyacrylic acid superplasticizer has better water-reducing effect and slump than the two commercially available polyacrylie acid superplasticizers. The AMPS-modified polyacrylic acid superplasticizer also shows significant improvement of the compressive strength, especially in comprehensive performance of HPC. In conclusion, the AMPS-modified polyacrylic acid superplastieizer is particularly suitable for the preparation of HPC.

Erosion resistance of treated dust soils based on the combined enzymatically induced carbonate precipitation and polyacrylic acid

The majority of cities worldwide are grappling with the challenge of dust pollution.Recently,the application potential of enzymatically induced carbonate precipitation(EICP),a novel environmentally friendly method,for dust control has been convincingly demonstrated.However,the long-term durability of EICP treatment is consistently a significant concern,particularly in regions prone to recurrent erosion caused by rainfall.As a result,the erosion durability of the EICP-treated dust soils requires further investigation.To address this,Polyacrylic acid(PAA)was added to the cementation solution in this study as the combined PAA and EICP treatment for dust control.The results showed that the addition of PAA slightly affected urea degradation;however,the combined PAA and EICP treatment significantly improved surface strength from 300 kPa to 500 kPa,especially for the wind-erosion resistance compared with the EICP treatment alone.The surface strength of samples treated with the combined PAA and EICP still exhibited a decrease due to repeated rainfall erosion,along with a reduction in calcium carbonate(CaCO_(3))contents.Nevertheless,the decreasing slopes of surface strength(k=13.434,14.002,or 14.186)in response to repeated rainfall for EICP-PAA-treated slopes were much smaller than those for EICP-treated samples(k=14.271),as well as the decreasing slopes of CaCO_(3)contents,which suggested the slopes with the combined treatment had significantly improved durability.By comparing the cementation effect and the influence of repeated rainfalls on treated dust samples,the EICP-PAA(50 g/L)treatment achieved better dust control effects.Overall,the combined treatment of EICP-PAA shows promising potential for effectively suppressing dust generation and enhancing erosion durability.

Nanometer TiO_2 Modified Polyacrylic Copolymer Sizing Agent

A series of new-type nanometer TiO2 modified polyacrylic copolymer sizing agent were synthesized from acrylic acid, ethyl acrylate, nanometer TiO2, oleic acid etc. by orthogonal design method. Results of the studies show that the synthetic method used in this paper was a new way and had never been found in the synthesis of acrylate sizing agent, and that the properties of those new-type size-agent were be improved, which had potential for substituting PVA (polyvinyl alcohol) sizing agent. The technology for solving the problem of nano-scale powder agglomeration and dispersion were also studied. The transmission electron microscope (TEM) observation showed that nano-TiO2had good dispersion and stability in aqueous solution and in sizing agent solution.

Preparation and Properties of pH-Responsive Intelligent Medical Dressing Based on Bacterial Cellulose/Polyacrylic Acid

Bacterial cellulose/polyacrylic acid (BC/PAA) pH-responsive hydrogels were prepared by free-radical polymerization (in situ) using BC as the raw material and AA as the monomer. The hydrogels were loaded with curcumin (Cur) to prepare pH-responsive intelligent medical dressings. The preparation process of the hydrogels was optimized by a single factor and response surface experiment using their swelling degree as an index. The structures of BC/PAA pH-responsive hydrogels were characterized by scanning electron microscope (SEM), Fourier Transform Infrared spectrometer (FTIR), X-ray diffraction (XRD), and tensile tester, and the swelling properties, mechanical properties, bacteriostatic properties, and drug release behavior were investigated. The results showed that the BC/PAA pH-responsive hydrogel has a three-dimensional network structure with the swelling rate up to 1600 g/g, compressive strength of up to 8 KPa, and good mechanical properties, and the drug release behavior was in line with the logistic dynamics model, and it has good inhibitory effects on common pathogens of wound infection: E. coli, S. aureus, and P. aeruginosa.

Adsorption of sodium polyacrylate at interface of dicalcium silicate-sodium aluminate solution

The adsorption isotherm of sodium polyacrylate on dicalcium silicate（2CaO-SiO2） in sodium aluminate solution at 80 ℃ was studied.The type of surface adsorption of sodium polyacrylate is saturated adsorption,and the adsorption behavior belongs to L-type,according with the monolayer adsorption model of Langmuir equation.The surface coverage of sodium polyacrylate is 1.06 mol/μm2.The relation curve between the surface pressure and the molecular area of adsorption film was obtained by Gibbs formula.The variation of interfacial energy caused by adsorption as well as the relationship between the relation curve and the type of adsorption was discussed.

SYNTHESIS AND APPLICATION OF NEW DETERGENT BUILDER POLYACRYLATE SODIUM

The low molecular weight polyacrylate sodium (PAA Na) detergent builder was synthesized with K 2S 2O 8 as initiator in a neutral aqueous medium. The influences of reaction conditions on the viscosity average molecular weight were studied. The critical value of synthetic PAA Na inhibiting the precipitation of CaCO 3 was determined and compared with that of other common builders. It is confirmed from SEM graphs that PAA Na can make CaCO 3 crystal defective. Washing tests show synthetic PAA Na can partially replace sodium tripolyphosphate (STPP) and is a potential polymeric detergent builder in low phosphate powder detergents.

计算机系统模拟语言CSSP的设计和实现

本文提出了用于计算机性能评价的CSSP模拟系统,该系统由计算机系统模拟语言CSSP和编译系统组成.CSSP是以PASCAL语言为基础、面向事件的计算机系统模拟语言,它兼有PASCAL语言和模拟语言的功能.