The interface behavior of polyamide 1010 (PA1010) and polypropylene (PP) was studied. In order to improve their interfacial adhesion, functional PP was prepared by means of grafting glycidyl methacrylate (GMA) on PP m...The interface behavior of polyamide 1010 (PA1010) and polypropylene (PP) was studied. In order to improve their interfacial adhesion, functional PP was prepared by means of grafting glycidyl methacrylate (GMA) on PP main chains and used instead of plain PP. Several technological characterizations were performed here on their interfaces. ESCA was used to confirm that some kind of reaction occurred between end groups of PA1010 and epoxy species of PP-g-GMA. The peel test was adopted to measure interfacial adhesion. It was found that the fracture energy of interfaces between PA1010 and PP-g-GMA was dramatically increased with the content of GMA. Their interfaces were observed as being blurred by using SEM and TEM and a crack that could be seen in the case of the interfaces of the PA1010 and the plain PP disappeared.展开更多
Iron ore tailings filled polypropylene (PP) composites were produced using the compo-indirect squeeze casting (C-ISC) process. Particle sizes 150, 212 and 300 μm where considered for different volume fractions of 5% ...Iron ore tailings filled polypropylene (PP) composites were produced using the compo-indirect squeeze casting (C-ISC) process. Particle sizes 150, 212 and 300 μm where considered for different volume fractions of 5% to 30% at intervals of 5%. The tensile and impact behavior of the produced composites were investigated, experimentally, by carrying out uniaxial tensile and izod impact tests to obtain tensile strength, elongation at break, modulus of elasticity and impact strength. Empirical data were compared with results obtained from models proposed by Nielsen, Bigg and Einstein. The experimental results show that elongation at break for iron ore tailings filled PP reduces with increasing 150 μm particle size. Tensile strength reduces with increasing filler. The Bigg equation exhibited improved predictability with decreasing particle size of filler in PP;while the Einstein equation which assumes poor adhesion gives the best prediction of modulus of elasticity with increasing particle size in PP. Izod impact strength decreases with particle size but increases with increasing volume content of iron ore tailings from 5% to 25% for each particle size considered.展开更多
用多组分熔融接枝的方法将甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)共同接枝到聚丙烯 (PP)上 ,制得具有较高GMA接枝率的多单体接枝聚丙烯 ,PP g (GMA co St) .将PP g (GMA co St)与尼龙 6 (PA6 )进行共混 ,利用扫描电镜 (SEM) ,差示扫...用多组分熔融接枝的方法将甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)共同接枝到聚丙烯 (PP)上 ,制得具有较高GMA接枝率的多单体接枝聚丙烯 ,PP g (GMA co St) .将PP g (GMA co St)与尼龙 6 (PA6 )进行共混 ,利用扫描电镜 (SEM) ,差示扫描量热计 (DSC)和广角X射线衍射 (WAXD)对共混物的形态和结晶进行了研究 .在共混过程中 ,PP g (GMA co St)与PA6反应原位生成了PP g PA6 ,有效改善了共混物的相容性 ,分散相尺寸明显减小 .在PP g (GMA co St) PA6为 3 7的体系中 ,PP g (GMA co St)出现分级结晶现象 ,其在较低温度下的结晶属于均相成核结晶 .在PP g (GMA co St) PA6为 7 3的体系中 ,由于PA6相分散细微 ,在通常结晶温度下不结晶 ,而是在低温下均相成核与PP g (GMA co St)同时结晶 .WAXD证实体系中接枝PP ,PA6为分别结晶 。展开更多
基金This work was supported by the National Natural Science Foundation of China.
文摘The interface behavior of polyamide 1010 (PA1010) and polypropylene (PP) was studied. In order to improve their interfacial adhesion, functional PP was prepared by means of grafting glycidyl methacrylate (GMA) on PP main chains and used instead of plain PP. Several technological characterizations were performed here on their interfaces. ESCA was used to confirm that some kind of reaction occurred between end groups of PA1010 and epoxy species of PP-g-GMA. The peel test was adopted to measure interfacial adhesion. It was found that the fracture energy of interfaces between PA1010 and PP-g-GMA was dramatically increased with the content of GMA. Their interfaces were observed as being blurred by using SEM and TEM and a crack that could be seen in the case of the interfaces of the PA1010 and the plain PP disappeared.
文摘Iron ore tailings filled polypropylene (PP) composites were produced using the compo-indirect squeeze casting (C-ISC) process. Particle sizes 150, 212 and 300 μm where considered for different volume fractions of 5% to 30% at intervals of 5%. The tensile and impact behavior of the produced composites were investigated, experimentally, by carrying out uniaxial tensile and izod impact tests to obtain tensile strength, elongation at break, modulus of elasticity and impact strength. Empirical data were compared with results obtained from models proposed by Nielsen, Bigg and Einstein. The experimental results show that elongation at break for iron ore tailings filled PP reduces with increasing 150 μm particle size. Tensile strength reduces with increasing filler. The Bigg equation exhibited improved predictability with decreasing particle size of filler in PP;while the Einstein equation which assumes poor adhesion gives the best prediction of modulus of elasticity with increasing particle size in PP. Izod impact strength decreases with particle size but increases with increasing volume content of iron ore tailings from 5% to 25% for each particle size considered.
文摘用多组分熔融接枝的方法将甲基丙烯酸缩水甘油酯 (GMA)和苯乙烯 (St)共同接枝到聚丙烯 (PP)上 ,制得具有较高GMA接枝率的多单体接枝聚丙烯 ,PP g (GMA co St) .将PP g (GMA co St)与尼龙 6 (PA6 )进行共混 ,利用扫描电镜 (SEM) ,差示扫描量热计 (DSC)和广角X射线衍射 (WAXD)对共混物的形态和结晶进行了研究 .在共混过程中 ,PP g (GMA co St)与PA6反应原位生成了PP g PA6 ,有效改善了共混物的相容性 ,分散相尺寸明显减小 .在PP g (GMA co St) PA6为 3 7的体系中 ,PP g (GMA co St)出现分级结晶现象 ,其在较低温度下的结晶属于均相成核结晶 .在PP g (GMA co St) PA6为 7 3的体系中 ,由于PA6相分散细微 ,在通常结晶温度下不结晶 ,而是在低温下均相成核与PP g (GMA co St)同时结晶 .WAXD证实体系中接枝PP ,PA6为分别结晶 。
