期刊文献+
共找到125篇文章
< 1 2 7 >
每页显示 20 50 100
Ni/Mo_2 N as a Highly Active Hydrodenitrogenation Catalyst
1
作者 Wen Yu ZHANG Xin Ping WANG +1 位作者 Heng Fang JIN Qin XIN (State key Laboratory of Catalysis,Dalian Institute of Chemical Physiscs,Chinese Academy Of Sciences,Dalian 116023)(Inner Mongolia Polytechnic Universal,Huhhot 010062) 《Chinese Chemical Letters》 SCIE CAS CSCD 1996年第9期849-852,共4页
The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K~973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is s... The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K~973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is shown that molybdenum nitrid(Mo2N) was formed above 923K and its intermediate MoO2 formed at about 573~623K under the rapid (5K/min.) TPR conditions.Mo2N is the most active species for pyridine HDN among MoO3,MoO2,MoS2,and Mo2N. Moreover,it can be promoted by adding Ni component.It is shown that the Ni/Mo2N catalyst prepared by adding some NiO into the precursor MoO3 has a steady HDN activity Which is far higher than that of the commercial sulfided NiMo/Al2O3(HR346) catalyst. 展开更多
关键词 MO Ni/Mo2 N as a highly active Hydrodenitrogenation catalyst
下载PDF
Active oxygen center in oxidative coupling of methane on La_(2)O_(3) catalyst 被引量:3
2
作者 Xiaohong Zhou Yaoqi Pang +4 位作者 Zebang Liu Evgeny I.Vovk Alexander Pvan Bavel Shenggang Li Yong Yang 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2021年第9期649-659,共11页
La_(2)O_(3) catalyzed oxidative coupling of methane(OCM) is a promising process that converts methane directly to valuable C_(2)(ethylene and ethane) products. Our online MS transient study results indicate that prist... La_(2)O_(3) catalyzed oxidative coupling of methane(OCM) is a promising process that converts methane directly to valuable C_(2)(ethylene and ethane) products. Our online MS transient study results indicate that pristine surface without carbonate species demonstrates a higher selectivity to C_(2) products, and a lower light-off temperature as well. Further study is focused on carbonate-free La_(2)O_(3) catalyst surface for identification of active oxygen species associated with such products behavior. XPS reveals unique oxygen species with O 1 s binding energy of 531.5 e V correlated with OCM catalytic activity and carbonates removal. However, indicated thermal stability of this species is much higher than the surface peroxide or superoxide structures proposed by earlier computation models. Motivated by experimental results,DFT calculations reveal a new more stable peroxide structure, formed at the subsurface hexacoordinate lattice oxygen sites, with energy 2.18 e V lower than the previous models. The new model of subsurface peroxide provides a perspective for understanding of methyl radicals formation and C_(2) products selectivity in OCM over La_(2)O_(3) catalyst. 展开更多
关键词 In-situ XPS Online MS DFT Oxidative coupling of methane High C_(2)selectivity active oxygen center La_(2)O_(3)catalyst
下载PDF
Highly efficient and stable electrooxidation of methanol and ethanol on 3D Pt catalyst by thermal decomposition of In2O3 nanoshells
3
作者 Yuhang Xie Hulin Zhang +4 位作者 Guang Yao Saeed Ahmed Khan Xiaojing Cui Min Gao Yuan Lin 《Journal of Energy Chemistry》 SCIE EI CAS CSCD 2017年第1期193-199,共7页
In this paper In2O3nanoshells have been synthesized via a facile hydrothermal approach. The nanoshells can be completely cracked into pony-size nanocubes by annealing, which are then used as a support of Pt catalyst f... In this paper In2O3nanoshells have been synthesized via a facile hydrothermal approach. The nanoshells can be completely cracked into pony-size nanocubes by annealing, which are then used as a support of Pt catalyst for methanol and ethanol electrocatalytic oxidation. The prepared In2O3and supported Pt catalysts (Pt/In2O3) were characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), field effect scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). Cyclic voltammetry (CV), linear sweep voltammetry (LSV), chronoamperometry and electrochemical impedance spectroscopy (EIS) were carried out, indicating the excellent catalytic performance for alcohol electrooxidation can be achieved on Pt/In2O3nanocatalysts due to the multiple active sites, high conductivity and a mass of microchannels and micropores for reactant diffusions arising from 3D frame structures compared with that on the Pt/C catalysts. © 2016 Science Press 展开更多
关键词 Alcohols catalyst activity catalysts CHRONOAMPEROMETRY Cyclic voltammetry Decomposition Electrocatalysis Electrochemical impedance spectroscopy Electron microscopy ELECTROOXIDATION Energy dispersive spectroscopy ETHANOL High resolution transmission electron microscopy Methanol NANOSHELLS Nanostructured materials Nanostructures Platinum Scanning electron microscopy Transmission electron microscopy X ray diffraction X ray photoelectron spectroscopy X ray spectroscopy
下载PDF
Comparative characterization of iridium loading on catalyst assessment under different conditions
4
作者 Zahra Amirsardari Akram Dourani +1 位作者 Mohamad Ali Amirifar Nooredin Ghadiri Massoom 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2021年第7期1233-1239,共7页
To discuss the potential role of iridium(Ir)nanoparticles loaded under atmospheric and high pressures,we prepared a series of cata-lysts with the same active phase but different contents of 10wt%,20wt%,and 30wt%on gam... To discuss the potential role of iridium(Ir)nanoparticles loaded under atmospheric and high pressures,we prepared a series of cata-lysts with the same active phase but different contents of 10wt%,20wt%,and 30wt%on gamma-alumina for decomposition of hydrazine.Un-der atmospheric pressure,the performance of the catalyst was better when 30wt%of the Ir nanoparticles was used with chelating agent that had greater selectivity of approximately 27%.The increase in the reaction rate from 175 to 220 h^(−1)at higher Ir loading(30wt%)was due to a good dispersion of high-number active phases rather than an agglomeration surface.As a satisfactory result of this investigation at high pressure,Ir catalysts with different weight percentages showed the same stability against crushing and activity with a characteristic velocity of approxim-ately 1300 m/s. 展开更多
关键词 iridium nanoparticles catalyst activity laboratory reactor atmospheric pressure high pressure
下载PDF
A highly active VOx-MnOx/CeO_(2) for selective catalytic reduction of NO:The balance between redox property and surface acidity 被引量:5
5
作者 Runnong Yang Zihan Gao +6 位作者 Ming Sun Guangying Fu Gao Cheng Wuyuan Liu Xiaobo Yang Xiangyun Zhao Lin Yu 《Journal of Rare Earths》 SCIE EI CAS CSCD 2021年第11期1370-1381,I0003,共13页
Excellent catalysts with low-temperature activity and relatively wide temperature window for selective catalytic reduction of NO with ammonia(NH_(3)-SCR) are highly demanded in view of the practical treatment of NO.He... Excellent catalysts with low-temperature activity and relatively wide temperature window for selective catalytic reduction of NO with ammonia(NH_(3)-SCR) are highly demanded in view of the practical treatment of NO.Herein,we have designed a highly active VOx-MnOx/CeO_(2) material based on the intrinsic requirement of SCR reaction for catalyst,namely redox sites and surface acid sites.The vanadium oxide and manganese oxide are highly dispersed over the ceria mesosphere via simple incipient wetness impregnation.The loading of manganese could introduce acid sites and enhance the redox property remarkably,while the loading of vanadium increases acid sites and weakens redox property.Through tentatively controlling the appropriate loading ratio of the two components,the optimal catalyst achieves a balance between redox property and surface acidity.The work shed light on the development of new SCR catalyst with superior low temperature activity,wide work temperature window and good hydrothermal stability. 展开更多
关键词 Redox property Surface acidity highly active catalyst NH_(3)-SCR Rare earths
原文传递
Bi-Atom Electrocatalyst for Electrochemical Nitrogen Reduction Reactions 被引量:2
6
作者 Wenchao Zhang Bin-Wei Zhang 《Nano-Micro Letters》 SCIE EI CAS CSCD 2021年第7期86-90,共5页
The electrochemical nitrogen reduction reaction(NRR)to directly produce NH3 from N_(2) and H_(2)O under ambient conditions has attracted significant attention due to its ecofriendliness.Nevertheless,the electrochemica... The electrochemical nitrogen reduction reaction(NRR)to directly produce NH3 from N_(2) and H_(2)O under ambient conditions has attracted significant attention due to its ecofriendliness.Nevertheless,the electrochemical NRR presents several practical challenges,including sluggish reaction and low selectivity.Here,bi-atom catalysts have been proposed to achieve excellent activity and high selectivity toward the electrochemical NRR by Ma and his co-workers.It could accelerate the kinetics of N_(2)-to-NH_(3) electrochemical conversion and possess better electrochemical NRR selectivity.This work sheds light on the introduction of bi-atom catalysts to enhance the performance of the electrochemical NRR. 展开更多
关键词 Electrochemical nitrogen reduction reaction Bi-atom catalysts Excellent activity High selectivity
下载PDF
ZnCl_(2)活化废旧涤纶基活性炭的制备及吸附性能
7
作者 张帮程 王立 《无机盐工业》 CAS CSCD 北大核心 2024年第7期126-134,共9页
为了实现废旧涤纶织物的资源化利用,通过ZnCl_(2)活化-高温热解的方法制备了废旧涤纶基活性炭(WPT-AC),采用XRD、FT-IR和BET等表征技术对其物相晶型、特征基团、比表面积和孔隙结构进行了表征,通过正交试验确定了制备WPT-AC的最优工艺,... 为了实现废旧涤纶织物的资源化利用,通过ZnCl_(2)活化-高温热解的方法制备了废旧涤纶基活性炭(WPT-AC),采用XRD、FT-IR和BET等表征技术对其物相晶型、特征基团、比表面积和孔隙结构进行了表征,通过正交试验确定了制备WPT-AC的最优工艺,评价了WPT-AC吸附亚甲基蓝(MB)性能并分析了吸附机理。结果表明:在质量分数为45%的Zn Cl_(2)溶液、热解温度为900℃、升温速率为5℃/min和热解时间为90 min的最优工艺条件下,制备的WPT-AC比表面积高达1 089.72 m^(2)/g、产率为58.45%。丰富的孔隙结构有利于提高其对污染物的吸附。在WPT-AC投加量为2.0 g/L、MB初始质量浓度为500 mg/L、吸附温度为40℃、吸附时间为80 min的条件下,WPT-AC对MB的去除率为97.49%。WPT-AC对土霉素(CIP)同样具有较好的吸附效果,且Ni(Ⅱ)共存条件下由于静电吸引的存在有利于吸附性能的提高。准二级动力学模型和Langmuir等温吸附模型更适合拟合WPT-AC吸附MB过程。 展开更多
关键词 废旧涤纶基活性炭 吸附 亚甲基蓝 氯化锌活化 高温热解
下载PDF
丙烷无氧脱氢Co基催化剂的研究进展
8
作者 史琪 王妍 +2 位作者 高照 解则安 赵震 《工业催化》 CAS 2024年第8期9-16,共8页
近年来Co基催化剂应用于丙烷脱氢反应展现出高于传统贵金属Pt基催化剂的催化活性,且逐渐成为研究热点。由于Co物种的多价态和多种配位的复杂性,导致其活性位结构和反应机理的认识不统一,尤其是在高温和还原性气氛(丙烷及其衍生物)条件下... 近年来Co基催化剂应用于丙烷脱氢反应展现出高于传统贵金属Pt基催化剂的催化活性,且逐渐成为研究热点。由于Co物种的多价态和多种配位的复杂性,导致其活性位结构和反应机理的认识不统一,尤其是在高温和还原性气氛(丙烷及其衍生物)条件下,CoO_(x)活性位通常被不同程度地还原,容易转变为高度分散的Co^(2+)物种或超小金属Co,通常被认为是高效的活性位点。根据催化剂载体不同,对Co基丙烷脱氢催化剂进行分类,总结不同配位环境、分散度、价态的Co物种及对丙烷脱氢C-H活化、丙烯选择性和催化剂稳定性的影响,为进一步设计高效的Co基丙烷脱氢催化剂提供参考。 展开更多
关键词 催化剂工程 丙烷脱氢 高温还原 CoO_(x) 限域 配位不饱和活性位
下载PDF
活性炭负载锌催化剂的制备及其处理煤化工废水的试验研究
9
作者 王春 马俊斯 +2 位作者 张雪雯 郭剑浩 丁洪贵 《工业用水与废水》 CAS 2024年第3期45-49,55,共6页
为实现煤化工高盐废水水质处理效能的提升,以宁夏生产的煤制活性炭为载体,采用直接浸渍法、沉淀-煅烧法2种负载方法,选取Zn元素作为催化剂的活性组分,制备了用于臭氧氧化降解工艺用催化剂,考察了催化剂对宁夏宁东地区煤化工高盐废水中CO... 为实现煤化工高盐废水水质处理效能的提升,以宁夏生产的煤制活性炭为载体,采用直接浸渍法、沉淀-煅烧法2种负载方法,选取Zn元素作为催化剂的活性组分,制备了用于臭氧氧化降解工艺用催化剂,考察了催化剂对宁夏宁东地区煤化工高盐废水中COD去除情况的探究。结果表明:将活性炭与浓度为0.4 mol/L的氯化锌溶液按照m(活性炭)∶V(溶液)=1∶3的比例混合,完全沉淀后,在氮气环境保护下,在恒定300℃的温度下煅烧2 h,制得活性组分为氧化锌的ZnO/AC催化剂,其比表面积为1063.45 m2/g,COD去除率高达71.7%,处理后废水中Zn^(2+)质量浓度增加99.8882 mg/L,高比表面积有利于发挥物理吸附与化学催化的协同作用,提高活性炭基催化剂的催化性能。该臭氧催化剂催化效果显著,可用于煤化工高盐废水中有机物的去除。 展开更多
关键词 活性炭 催化剂 臭氧催化氧化 比表面积 COD去除率 煤化工 高盐废水
下载PDF
催化剂BCE-H 200在高密度聚乙烯装置上的应用
10
作者 邓起垚 吴希 +2 位作者 辛麟 荣力超 余宗蔚 《石化技术与应用》 CAS 2024年第1期40-44,共5页
在中韩(武汉)石油化工有限公司Hostalen ACP高密度聚乙烯装置上,采用国产催化剂BCE-H 200分别替代进口催化剂Z 501和Z 509生产了高密度聚乙烯注塑料和薄膜料。分析对比了3种催化剂的活性及粉料粒径分布、堆积密度,并对生产的注塑料和薄... 在中韩(武汉)石油化工有限公司Hostalen ACP高密度聚乙烯装置上,采用国产催化剂BCE-H 200分别替代进口催化剂Z 501和Z 509生产了高密度聚乙烯注塑料和薄膜料。分析对比了3种催化剂的活性及粉料粒径分布、堆积密度,并对生产的注塑料和薄膜料进行了表征分析。结果表明:BCE-H 200的活性较Z 501低13.8%,较Z 509高49.2%,其氢调敏感性较Z 501和Z 509低;BCE-H 200生产注塑料和薄膜料时,粉料的粒径分布比进口催化剂Z 501和Z 509更集中,细粉更少,但堆积密度低;采用催化剂BCE-H 200替代催化剂Z 501生产的注塑料刚性较高,韧性较低,相对分子质量分布更宽;采用催化剂BCE-H 200替代催化剂Z 509生产的薄膜料,力学性能变化不大,相对分子质量分布更宽。 展开更多
关键词 高密度聚乙烯 Hostalen ACP工艺 催化剂 注塑料 薄膜料 活性 粒径 堆积密度 相对分子质量及其分布
下载PDF
A novel and effective Zn/PEI-MCM catalyst for the acetylene hydration to acetaldehyde 被引量:1
11
作者 Qinqin Wang Mingyuan Zhu +1 位作者 Bin Dai Jinli Zhang 《Chinese Chemical Letters》 SCIE CAS CSCD 2019年第6期1244-1248,共5页
MCM-41 material was modified by polyethyleneimine (PEI) using ultrasonic assisted impregnation method with different PEI loading (P-MCM-x, x=0–15 wt%). The synthesised P-MCM-x materials and corresponding Zn/P-MCM-x c... MCM-41 material was modified by polyethyleneimine (PEI) using ultrasonic assisted impregnation method with different PEI loading (P-MCM-x, x=0–15 wt%). The synthesised P-MCM-x materials and corresponding Zn/P-MCM-x catalysts were characterised by FTIR, XRD, TEM, BET, XPS, TG and H2-TPR, as well as their catalytic performance in the hydration of acetylene was investigated. The results showed that the modified materials retained the mesoporous structure with good thermostability, and the corresponding Zn/P-MCM-x displayed the higher catalytic performance than that of Zn/MCM-41 catalyst, especially for the Zn/P-MCM-12 catalyst with about 88%C2H2 conversion and 85%selectivity, and the optimal content of PEI is 12 wt%. More importantly, the introduction of PEI enhanced metal-support interaction to make the better metal dispersion and more active sites, and the charge transfer from N atom to Zn species. These all would be responsible for the high activity of the modified Zn catalysts in the acetylene hydration. 展开更多
关键词 POLYETHYLENEIMINE Modified MCM-41 ACETYLENE HYDRATION Zinc catalyst High activity
原文传递
Highly dispersed Ru nanospecies on N-doped carbon/MXene composite for highly efficient alkaline hydrogen evolution 被引量:1
12
作者 Minying Wu Xueliang Fan +6 位作者 Wenbiao Zhang Bin Chen Tong Ye Qian Zhang Yuanyuan Fang Yajun Wang Yi Tang 《Chinese Chemical Letters》 SCIE CAS CSCD 2024年第4期153-159,共7页
Hydrogen has emerged as a promising environmentally friendly energy source. The development of lowcost, highly active, stable, and easily synthesized catalysts for hydrogen evolution reactions(HER) remains a significa... Hydrogen has emerged as a promising environmentally friendly energy source. The development of lowcost, highly active, stable, and easily synthesized catalysts for hydrogen evolution reactions(HER) remains a significant challenge. This study explored the synthesis of nitrogen-doped MXene-based composite catalysts for enhanced HER performance. By thermally decomposing RuCl_(3) coordinated with melamine and formaldehyde resin, we successfully introduced nitrogen-doped carbon(N–C) with highly dispersed ruthenium(Ru) onto the MXene surface. The calcination temperature played a crucial role in controlling the size of Ru nanoparticles(Ru NPs) and the proportion of Ru single-atom(Ru SA), thereby facilitating the synergistic enhancement of HER performance by Ru NPs and Ru SA. The resulting catalyst prepared with a calcination temperature of 600℃, Ti_(3)C_(2)T_x-N/C-Ru-600(TNCR-600), exhibited exceptional HER activity(η10= 17 m V) and stability(160 h) under alkaline conditions. This work presented a simple and effective strategy for synthesizing composite catalysts, offering new insights into the design and regulation of high-performance Ru-based catalysts for hydrogen production. 展开更多
关键词 HER activity highly dispersed Ru-based catalysts MXene Alkaline condition
原文传递
高活性低细粉含量催化剂在气相法Horizone工业装置的试用
13
作者 李元凯 黄肖思 郑培锦 《合成树脂及塑料》 CAS 北大核心 2023年第6期33-38,共6页
将丙烯聚合用高活性低细粉含量IC2催化剂在气相法Horizone工业装置进行了试用。结果表明:与对比催化剂相比,IC2催化剂活性提高了27%,氢调性能接近,共聚性能略差,催化剂孔隙率略高;采用IC2催化剂制备的聚丙烯粉料的细粉含量明显低于采用... 将丙烯聚合用高活性低细粉含量IC2催化剂在气相法Horizone工业装置进行了试用。结果表明:与对比催化剂相比,IC2催化剂活性提高了27%,氢调性能接近,共聚性能略差,催化剂孔隙率略高;采用IC2催化剂制备的聚丙烯粉料的细粉含量明显低于采用对比催化剂;采用IC2催化剂时反应器的料位需要适当调低,所制聚丙烯的等规指数与采用对比催化剂接近,产品性能接近。 展开更多
关键词 聚丙烯 Horizone工艺 细粉含量 催化剂 高活性
下载PDF
4.1Mt/a柴油加氢装置国Ⅴ标准长周期潜能分析
14
作者 姚立松 李云 《石化技术》 CAS 2023年第2期40-41,16,共3页
研究了国Ⅴ柴油质量标准下,国内某4.1Mt/a柴油加氢装置长周期运行潜能。根据催化剂反应温度工业数据,测算该装置一反催化剂平均失活速度0.0306℃/d、二反催化剂平均失活速度0.0284℃/d。一反、二反床层压降上升趋势平缓,压降不会成为装... 研究了国Ⅴ柴油质量标准下,国内某4.1Mt/a柴油加氢装置长周期运行潜能。根据催化剂反应温度工业数据,测算该装置一反催化剂平均失活速度0.0306℃/d、二反催化剂平均失活速度0.0284℃/d。一反、二反床层压降上升趋势平缓,压降不会成为装置长周期运行的制约因素。对高压空冷腐蚀情况进行测算,高压空冷的腐蚀系数Kp值为0.24,空冷入口流速2.52m/s,出口流速2.00m/s,管束内平均流速1.43m/s。综合以上分析认为:该柴油加氢装置长周期运行时长可达1364天。 展开更多
关键词 柴油加氢 催化剂活性 反应压降 高压空冷 腐蚀
下载PDF
CO_(2)加氢制高碳α-烯烃Fe基催化剂研究进展 被引量:2
15
作者 李自琴 王康洲 +3 位作者 高新华 马清祥 赵天生 张建利 《低碳化学与化工》 CAS 北大核心 2023年第3期11-21,共11页
随着“双碳”目标的提出,二氧化碳(CO_(2))减排和资源化利用受到研究者的广泛关注。CO_(2)耦合绿氢技术制高附加值化学品是CO_(2)资源化利用的有效途径之一。高碳α-烯烃是重要的化工原料,围绕非均相催化体系催化CO_(2)加氢制高碳α-烯... 随着“双碳”目标的提出,二氧化碳(CO_(2))减排和资源化利用受到研究者的广泛关注。CO_(2)耦合绿氢技术制高附加值化学品是CO_(2)资源化利用的有效途径之一。高碳α-烯烃是重要的化工原料,围绕非均相催化体系催化CO_(2)加氢制高碳α-烯烃的相关研究,总结分析了CO_(2)加氢制高碳α-烯烃的催化剂设计理念、反应机理、助剂、载体以及制备工艺对催化剂催化性能的影响和构效关系。其中,设计高效催化剂有效调控C—O键活化和C—C链增长仍存在挑战。对CO_(2)加氢制高碳α-烯烃的发展方向进行了展望,可为CO_(2)加氢制高碳α-烯烃新型催化剂的开发提供参考。 展开更多
关键词 CO_(2)加氢 Fe基催化剂 高碳α-烯烃 构效关系 反应机理
下载PDF
SiO_(2)包覆膜对介孔Pd/SiO_(2)催化蒽醌加氢制备双氧水的作用
16
作者 李大卫 王树东 +1 位作者 苏宏久 严华 《材料导报》 CSCD 北大核心 2023年第24期244-248,共5页
本工作以2-戊基蒽醌生产过氧化氢的反应过程为研究背景,使用平均孔径为12 nm的介孔球形氧化硅载体,利用强静电吸附(SEA)法制备了Pd/SiO_(2)催化剂,并使用四乙氧基硅烷包覆催化剂所负载的Pd颗粒,制备出用于蒽醌加氢的Pd@SiO_(2)/SiO_(2)... 本工作以2-戊基蒽醌生产过氧化氢的反应过程为研究背景,使用平均孔径为12 nm的介孔球形氧化硅载体,利用强静电吸附(SEA)法制备了Pd/SiO_(2)催化剂,并使用四乙氧基硅烷包覆催化剂所负载的Pd颗粒,制备出用于蒽醌加氢的Pd@SiO_(2)/SiO_(2)球形颗粒催化剂。相较于未经包覆修饰的Pd/SiO_(2)球形催化剂,Pd@SiO_(2)/SiO_(2)催化剂表现出较高的100%选择性,以及高加氢活性,时空产率高出16.4%;同时,利用物理吸附(BET)、粉末X射线衍射(XRD)、透射电镜(TEM)、H_(2)-TPR、XPS等手段对所制备的Pd@SiO_(2)/SiO_(2)及Pd/SiO_(2)催化剂进行表征,可观察到经包覆后,Pd颗粒表面有0.1 nm左右的SiO_(2)膜,催化剂的比表面积和孔容相较于载体有所增加,而孔径则减小;H_(2)-TPR及XPS表征结果则显示,在Pd@SiO_(2)/SiO_(2)上,由于SiO_(2)薄膜的包覆作用,Pd@SiO_(2)/SiO_(2)的Pd~0物种的结合能更高,Pd颗粒与载体间的相互作用更强;上述制备方法均使得Pd@SiO_(2)/SiO_(2)催化剂表现出较高的选择性及活性。 展开更多
关键词 介孔氧化硅材料 双氧水 蒽醌加氢 钯贵金属催化 氧化硅包覆 高选择性 高活性
下载PDF
不同压力硫化的渣油加氢催化剂的活性相研究 被引量:1
17
作者 袁蕙 贾燕子 徐广通 《光谱学与光谱分析》 SCIE EI CAS CSCD 北大核心 2023年第S01期209-210,共2页
开发溶剂保护转移、制样、Raman和CO-FTIR(准)原位表征等系列方法,研究不同压力硫化的渣油加氢脱硫催化剂活性中心的类型、分布、配位状态等差异。结果表明高压液相硫化有利于金属活性相的完全硫化和助剂化的提高,适度钝化部分酸性中心... 开发溶剂保护转移、制样、Raman和CO-FTIR(准)原位表征等系列方法,研究不同压力硫化的渣油加氢脱硫催化剂活性中心的类型、分布、配位状态等差异。结果表明高压液相硫化有利于金属活性相的完全硫化和助剂化的提高,适度钝化部分酸性中心且促进NiMoS相的形成。这为深入研究实际工业渣油加氢催化剂高压硫化活性相提供技术支撑,并有助于加深理解活性相的本质,为催化剂配方和硫化工艺条件的优化提供信息。 展开更多
关键词 渣油加氢催化剂 活性相 高压硫化
下载PDF
应对焦化石脑油加氢装置长周期运行的催化剂策略研究
18
作者 陈光 徐大海 +1 位作者 丁贺 范思强 《炼油技术与工程》 CAS 2023年第9期42-45,共4页
目前焦化石脑油加氢装置要实现长周期稳定运行,需要重点解决两大问题:焦化石脑油的二烯烃含量高,在较高的反应温度下易缩合生焦,导致反应器压力降上升;前序加工阶段使用的含硅添加剂会造成二氧化硅在催化剂表面沉积,导致催化剂失活快、... 目前焦化石脑油加氢装置要实现长周期稳定运行,需要重点解决两大问题:焦化石脑油的二烯烃含量高,在较高的反应温度下易缩合生焦,导致反应器压力降上升;前序加工阶段使用的含硅添加剂会造成二氧化硅在催化剂表面沉积,导致催化剂失活快、运行周期短。针对上述问题提出了解决方案:对焦化石脑油加氢工艺流程进行了改进,增设了低温脱二烯烃保护反应器;配套开发了容硅能力强的加氢捕硅剂及高活性加氢精制催化剂。应用结果表明:焦化石脑油加氢装置的运行周期大幅延长,为装置的长周期运行提供了技术保障。 展开更多
关键词 焦化石脑油 加氢装置 加氢捕硅剂 低温保护反应器 高活性加氢精制催化剂 硅杂质沉积量
下载PDF
高活性低水比GS-HA乙苯脱氢催化剂工业应用总结
19
作者 黎志刚 《炼油技术与工程》 CAS 2023年第5期46-49,共4页
介绍了GS-HA乙苯脱氢催化剂在中国石化海南炼油化工有限公司80 kt/a苯乙烯装置低水比工业试验,分析了低水比运行期间装置的节能效果和产生的经济效益。结果表明:该催化剂的乙苯转化率和苯乙烯选择性保持在64.5%以上和96.4%以上,说明该... 介绍了GS-HA乙苯脱氢催化剂在中国石化海南炼油化工有限公司80 kt/a苯乙烯装置低水比工业试验,分析了低水比运行期间装置的节能效果和产生的经济效益。结果表明:该催化剂的乙苯转化率和苯乙烯选择性保持在64.5%以上和96.4%以上,说明该剂催化性能和稳定性优异,装置综合能耗降低1950.88 MJ/t(以苯乙烯计),节约蒸汽5.21 t/h,苯乙烯产量增加13.4 t/d,创造了良好的经济效益。运行后期平均水比为1.25,乙苯转化率保持在65.4%以上,苯乙烯选择性在96.8%以上,苯乙烯单体收率大于63.4%,反应性能优异,苯乙烯产量稳定,催化剂稳定性好,装置运行周期达到57个月,创国内装置单批催化剂满负荷运行的最长纪录。 展开更多
关键词 高活性 低水比 乙苯脱氢催化剂 反应器升温 转化率 选择性 综合能耗 经济效益
下载PDF
基于钛镁催化剂合成瓶用聚酯的动力学研究 被引量:7
20
作者 关震宇 周文乐 +1 位作者 张玉梅 王华平 《纺织学报》 EI CAS CSCD 北大核心 2021年第3期64-70,共7页
为研究钛镁复合催化剂(TMPC)在瓶用高黏聚酯制备过程中的活性与耐水解性对合成聚酯性能的影响,通过测试聚酯合成过程中TMPC的水解特性,聚酯的数均分子量、乙醛含量、色相等指标,研究了不同催化体系的酯化、熔融缩聚和固相缩聚反应动力... 为研究钛镁复合催化剂(TMPC)在瓶用高黏聚酯制备过程中的活性与耐水解性对合成聚酯性能的影响,通过测试聚酯合成过程中TMPC的水解特性,聚酯的数均分子量、乙醛含量、色相等指标,研究了不同催化体系的酯化、熔融缩聚和固相缩聚反应动力学。结果表明:TMPC催化剂耐水解,在酯化及缩聚过程均有明显的催化作用,在相同聚合条件下按用量推算相当于锑系催化剂活性的36倍,其缩聚时间比乙二醇锑(EGA)缩短60 min,酯化反应活化能均低于EGA与乙二醇钛(EGT)催化剂,固相缩聚速度与EGA接近,活化能略高于EGA;TMPC作为催化剂,经固相缩聚获得了数均分子量为25734 g/mol的高黏聚酯,其色相与EGA催化聚酯相当,而乙醛含量低至0.59μg/g,可作为催化瓶用高黏聚酯的绿色高效催化剂。 展开更多
关键词 钛镁催化剂 瓶用聚酯 高黏聚酯 聚合反应动力学 乙醛含量
下载PDF
上一页 1 2 7 下一页 到第
使用帮助 返回顶部