Surface Modification of Polyethylene (PE) Films Using Dielectric Barrier Discharge Plasma at Atmospheric Pressure

Modification of the surface properties of polyethylene （PE） films is studied using air dielectric barrier discharge at atmospheric pressure. The treated samples are examined by Water contact angle measurements, Fourier transform infrared attenuated total reflection spectroscopy （FTIR-ATR）, X-ray photoelectron spectroscopy （XPS） and scanning electron microscopy （SEM）. With the increase in treating time, the water contact angle changes from 93.2° before treatment to a minimum of 53.3° after a treatment for 50 s. Both ATR and XPS results show some oxidized species are introduced into the sample surface by the plasma treatment and the tendency of the water contact angle with the treating time is the same as that of oxygen concentration on the treated sample surface. SEM result shows the surface roughness of PE samples increases with the treatment time increasing.

Surface Treatment of Polyethylene Terephthalate Film Using Atmospheric Pressure Glow Discharge in Air

Non-thermal plasmas under atmospheric pressure are of great interest in polymer surface processing because of their convenience, effectiveness and low cost. In this paper, the treatment of Polyethylene terephthalate (PET) film surface for improving hydrophilicity using the non-thermal plasma generated by atmospheric pressure glow discharge (APGD) in air is conducted. The discharge characteristics of APGD are shown by measurement of their electrical discharge parameters and observation of light-emission phenomena, and the surface properties of PET before and after the APGD treatment are studied using contact angle measurement, x-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). It is found that the APGD is homogeneous and stable in the whole gas gap, which differs from the commonly filamentary dielectric barrier discharge (DBD). A short time (several seconds) APGD treatment can modify the surface characteristics of PET film markedly and uniformly. After 10 s APGD treatment, the

The Aging Study on Polyethylene Terephthalate with Surface Modification by Water Vapor Plasma

The aging effects of the contact angle and surface energy on polyethylene terephthalate (PET) have been investigated with surface modification by water vapor plasma. The experimental results show that the contact angle of water and PET decreases obviously and surface energy increases. However, with the increase of the aging time, the contact angle and surface energy change back gradually to original state.

SURFACE TREATMENT OF POLY (ETHYLENE TEREPHTHALATE) FABRIC WITH POLYETHYLENEIMINE

A branched polyethyleneimine (BPEI) was applied to poly(ethylene terephthalate)(PET) fabric to improve its surface moisture absorption so that the fabric becomes lessliable to retention of electrostatic charg. The durability of this treatment was assessed bywashing and followed by measurement of charge development on the fabric. The treatedsamples showed improved surface wetting compared to the untreated. The results areconsistent with attachment of the BPEI to the PET surface by a cross-linking mechanism.

Influence of air addition on surface modification of polyethylene terephthalate treated by an atmospheric pressure argon plasma brush

An atmospheric pressure argon plasma brush with air addition is employed to treat polyethylene terephthalate(PET)surface in order to improve its hydrophilicity.Results indicate that the plasma plume generated by the plasma brush presents periodically pulsed current despite a direct current voltage is applied.Voltage-current curve reveals that there is a transition from a Townsend discharge regime to a glow one during one discharge period.Optical emission spectrum indicates that more oxygen atoms are produced in the plume with increasing air content,which leads to the better hydrophilicity of PET surface after plasma treatment.Besides,an aging behavior is also observed.The hydrophilicity improvement is attributed to the production of oxygen functional groups,which increase in number with increasing air content.Moreover,some grain-like structures are observed on the treated PET surface,and its mean roughness increases with increasing air content.These results are of great importance for the hydrophilicity improvement of PET surface with a large scale.

SURFACE MODIFICATION ON STEEL BY RARE EARTH AND LASER TREATMENT

ＳＵＲＦＡＣＥＭＯＤＩＦＩＣＡＴＩＯＮＯＮＳＴＥＥＬＢＹＲＡＲＥＥＡＲＴＨＡＮＤＬＡＳＥＲＴＲＥＡＴＭＥＮＴ①ＳｈｅｎＹｉｆｕ１，２，ＦｅｎｇＺｈｏｎｇｃｈａｏ１，ＣｈｅｎＪｉｚｈｉ１，ＬｉａｎｇＹｏｎｇ１１ＩｎｓｔｉｔｕｔｅｏｆＭｅｔａｌＲｅｓｅａ...

Surface Modification of Electrospun Poly(L-lactide)/Poly(ε-caprolactone)Fibrous Membranes by Plasma Treatment and Gelatin Immobilization

Biopolymer fibers have great potential for technical applications in biomaterials.The surface properties of fibers are of importance in these applications.In this study,electrospun poly(L-lactide)(PLLA)/poly(ε-caprolactone)(PCL)membranes were modified by cold plasma treatment and coating gelatin to improve the surface hydrophilic properties.The morphologies of the fibers were observed by scanning electron microscopy(SEM).Atomic force microscopy(AFM)was employed to show the surface characteristics of the fibers.The chemical feature of the fibrous membrane surfaces was examined by X-ray photoelectron spectroscopy(XPS).The surface wettability of the fibrous membrane was also characterized by water contact angle measurements.All these results show that plasma treatment can have profound effects on the surface properties of fibrous membranes by changing their surface physical and chemical features.Gelatin-PLLA/PCL membrane has great potential in applications of tissue engineering scaffolds.

Surface Modification of AB_2 and AB_5 Hydrogen Storage Alloy Electrodes by the Hot-Charging Treatment

The effect of the hot-charging treatment on the performance of AB(2) and AB(5) hydrogen storage alloy electrodes was investigated. The result showed that the treatment can markedly improve the voltage plateau ratio (VPR), the high rate discharge ability (HRDA), the diffusion coefficient of hydrogen DH and the discharge capacity of the AB2 hydrogen storage alloy electrode. The SEM analysis showed that the hot-charging treatment brings about a Ni-rich surface due to the dissolution of Zr oxides. It is also very helpful for the improvement of the kinetic properties of AB2 hydrogen storage alloy electrode because the microcracking of the surface results in fresh surface. This can be the basic modification treatment for NiMH battery used in electric vehicles (EVs) in the future. But for AB(5) type alloys, the treatment has the disadvantage of impairing the comprehensive electrochemical properties, because the surface of the alloy may be corroded during the treatment. The mechanism of the surface modification of the electrode is also proposed.

Surface Treatment of UHMWPE Fibers for Adhesion Promotion in Epoxy Polymers

Surface of Ultra-high molecular weight polyethylene （UHMWPE） fiber were treated by chromic acid chemical etching, pyrrole chemical vapour phase deposition and the complex of these two methods, respectively. The change of surface properties and structure of fibers were discussed by Fiour Transform Infrared Spectroscope （FTIR）, Dynamic Mechanical Analysis （DMA） and Scanning Electron Microscope （SEM）. The results show that some new oxygenous groups could be found on surface of UHMWPE fiber after chromic acid chemical etching, which enhanced intemolecular interaction with polypyrrcle. The adhesion of the fiber and resin natrix increased after pyrrole chemical vapour deposition. When chromic acid etching combined with pyrrole chemical vapor deposition, the treated fiber not only has the same properties as original fiber bat also outstanding adhesion to epoxy resin matrix, and its composites have better mechanic properties shear strength）, resulting from intemolecular interaction treated fiber and polypyrrole.

Enhanced Interfacial Adhesion in HDPE/HA Composites by Surface Modification of HA Particles via in situ Polymerization and Copolymerization

Hydroxyapatite （ HA ）- reinforced high density polyethylene （HDPE） was developed as a bone replacement material,In order to enhaace the interfacial bonding between HA and polyethylene and improve the mechanical properties of HDPE/ HA composites, the surface of the micron-sized HA particles was modified by in situ polymerization of butyl acrylate （ BA ） and in situ copolymerization of vinyl triethoxyl silane （ VTES ） and BA , then the modifwd HA particles were compounded with HDPE. The effects of the surface modification of HA on morphology and mechanical properties of HDPE/ HA composites were investigated. The experimental results show that the presence of HA particles does tuft inhibit the polymerization of BA . The poly（ butyl acrylate） （ PBA ） segments on the HA surface enhance the compatibility between HA and HDPE, improve the dispersion of HA particles in HDPE matrix, and enhance the interfacial adhesion between HA and matrix. Surface modifieations , especially by in situ copolymerization of VTES and BA, significantly increase notch impact strengths and marginal stiffness and tensile strengths of HDPE/HA composites. And it is found that there is a critical thickness of PBA coating on HA panicles for optimum mechanical properties of HDPE / HA composites.

Peanut Shell Activated Carbon： Characterization, Surface Modification and Adsorption of Pb^2＋ from Aqueous Solution

Metal ion contamination of drinking water and waste water, especially with heavy metal ion such as lead, is a serious and ongoing problem. In this work, activated carbon prepared from peanut shell （PAC） was used for the removal of Pb^2＋ from aqueous solution. The impacts of the Pb25 adsorption capacities of the acid-modified carbons oxidized with HNO3 were also investigated. The surface functional groups of PAC were confirmed by Fourier transform infrared （FTIR） spectroscopy, X-ray photoelectron spectroscopy （XPS）, Boehm titration. The textural properties （surface area, total pore volume） were evaluated from the nitrogen adsorption isotherm at 77 K. The experimental results presented indicated that the adsorption data fitted better with the Langmuir adsorption model. A comparative study with a commercial granular activated carbon （GAC） showed that PAC was 10.3 times more efficient compared to GAC based on Langmuir maximum adsorption capacity. Further analysis results by the Langmuir equation showed that HNO3 [20% （by mass）] modified PAC has larger adsorption capacity of Pb^2＋ from aqueous solution （as much as 35.5 mg·g^-1）. The adsorption capacity enhancement ascribed to pore widening, increased cation-exchange capacity by oxygen groups, and the promoted hydrophilicity of the carbon surface.

Insight into the remaining high surface energy of atmospheric DBD plasma-treated polyethylene web after three months' aging

In this paper, we report the modification of polyethylene(45 μm in thickness) webs through a roll-to-roll dielectric barrier discharge plasma treatment in an open atmospheric environment.Our work differs from the normal adopted corona discharge treatment at an atmospheric pressure, in that three monomers: allylamine, acrylic acid, and ethanol, are inlet into the discharge zone by argon(Ar) carrier gas. As a comparison, Ar plasma treatment is also carried out. We focus on the aging properties of treated plastics in the open air. It is found that the modified webs can retain the surface energy as high as 50.0?±?1 mN m^(-1) for more than three months. After characterization of the as-prepared and aged samples by the surface roughness, the wettability, and the chemical structure, the mechanism of retaining high surface energy is then presumed. We think that the initial high surface energy just after plasma treatment is correlated to the grafted functional groups, while the over 50.0 mN m^(-1) remaining surface energy after three month aging is due to the stable concentrations of oxygen-contained and nitrogencontained groups by post-reaction on the surfaces.

Surface modification for La_(1-x)Ce_x (NiCoMnAl)_5 hydride electrode by hot charging in potassium borohydride solution

The La 1- x Ce x (NiCoMnAl) 5 alloy electrodes were treated by hot charging in alkaline aqueous solution containing KBH 4. The activation behavior, hydrogen diffusion coefficient and maximum discharging capacity, high rate discharging capability of alloy electrodes were tested. The surface morphology and element content were observed by scanning electron microscope. The results show that the alloy electrode is fully activated after the second charging discharging cycle and has a high rate discharging capability of 85% at 900 mA/g. The surface has a lot of micro cracks and hydrogen diffusion coefficient is about (2～3)×10 -9 cm 2/s . Therefore, this method can markedly improve activation behavior and high rate charging capacity of the alloy electrode. The mechanism of this surface modification of the alloy electrode is also discussed. [

Surface Modification of Polyimide Film by Dielectric Barrier Discharge at Atmospheric Pressure

In this paper,polyimide（PI）films are modified using an atmospheric pressure plasma generated by a dielectric barrier discharge（DBD）in argon.Surface performance of PI film and its dependence on exposure time from 0 s to 300 s are investigated by dynamic water contact angle（WCA）,field emission scanning electron microscopy（FESEM）,and Fourier transform infrared spectroscopy in attenuated total multiple reflection mode（FTIR-ATR）.The study demonstrates that dynamic WCA exhibits a minimum with 40 s plasma treatment,and evenly distributed nano-dots and shadow concaves appeared for 40 s and 12 s Ar plasma treatment individually.A short period of plasma modification can contribute to the scission of the imide ring and the introduction of C-O and C=O（-COOH）by detailed analysis of FTIR-ATR.

Synergistic Effect of Atmospheric Pressure Plasma Pre-Treatment on Alkaline Etching of Polyethylene Terephthalate Fabrics and Films

Dyeing of PET materials by traditional methods presents several problems.Plasma technology has received enormous attention as a solution for the environmental problems related with textile surface modifications,and there has been a rapid development and commercialization of plasma technology over the past decade.In this work,the synergistic effect of atmospheric pressure plasma on alkaline etching and deep coloring of dyeing properties on polyethylene terephthalate（PET）fabrics and films was investigated.The topographical changes of the PET surface were investigated by atomic force microscopy（AFM）images,which revealed a smooth surface morphology of the untreated sample whereas a high surface roughness for the plasma and/or alkaline treated samples.The effects of atmospheric pressure plasma on alkaline etching of the structure and properties of PET were investigated by means of differential scanning calorimetry（DSC）,the main objective of performing DSC was to investigate the effect of the plasma pre-treatment on the T_g and T_m.Using a tensile strength tester YG065 H and following a standard procedure the maximum force and elongation at maximum force of PET materials was investigated.Oxygen and argon plasma pre-treatment was found to increase the PET fabric weight loss rate.The color strength of PET fabrics was increased by various plasma pre-treatment times.The penetration of plasma and alkaline reactive species deep into the PET structure results in better dyeability and leaves a significant effect on the K/S values of the plasma pre-treated PET.It indicated that plasma pre-treatment has a great synergistic effect with the alkaline treatment of PET.

Structural characteristics,dispersion,and modification of fibrous brucite

Fibrous bmcite has very unique structure and physical properties. Brucite fibers were exfoliated into single nanofibers by using dioctyl sodium sulfosuccinate （AOT） as a dispersant through mechanical agitation and ultrasonic dispersion; and then, the nanofibers were modified by stearic acid and （3-aminopropyl）triethoxysilane （y-APS） compound modification agent. The nanofibers were characterized by using X-ray diffraction （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, Fourier transform infrared spectroscopy （FTIR）, and thermal gravimetric analysis. It is found that AOT has good effect on the dispersion. The single fiber has a consis- tent morphology, and fibrous bmcite is dispersed and modified without destroying the crystal structure. Infrared and thermal analysis shows that the surface modification of fibrous brucite is achieved by forming chemical bonds between the coupling agent and magnesium hydroxide.

Mechariical and Abrasion Properties of Polyethylene Terephthalate Films Coated with SiO2/Epoxy Hybrid Material

Hybrid materials were prepared using a silane coupling agent, tetraethoxysilane （ TEOS ） as the precursor, dilute hydrochloric acid as the catalyst, and epoxy as the matrices. The films coated with hybrid materials were expected to improve abrasion resistance and mechanical properties. The morphology, mechanical properties, adhesion, and abrasion resistance of the polyethylene terephthalate （PET） films were characterized using an atomic force microscope, a tensile testing machine, a bagger knife, and a reciprocating fabric abrasion tester. The result of research indicated that the modification significantly affected the abrasion resistance and roughness. The-tensile strength and abrasion resistance of the modified PET films increased by 40% and 50% respectively at 3 % TEOS mass fraction.

Surface-modified Ag@Ru-P25 for photocatalytic CO_(2) conversion with high selectivity over CH_(4) formation at the solid–gas interface

Systematic optimization of the photocatalyst and investigation of the role of each component is important to maximizing catalytic activity and comprehending the photocatalytic conversion of CO_(2) reduction to solar fuels.A surface-modified Ag@Ru-P25 photocatalyst with H_(2)O_(2) treatment was designed in this study to convert CO_(2) and H_(2)O vapor into highly selective CH4.Ru doping followed by Ag nanoparticles(NPs)cocatalyst deposition on P25(TiO_(2))enhances visible light absorption and charge separation,whereas H_(2)O_(2) treatment modifies the surface of the photocatalyst with hydroxyl(–OH)groups and promotes CO_(2) adsorption.High-resonance transmission electron microscopy,X-ray photoelectron spectroscopy,X-ray absorption near-edge structure,and extended X-ray absorption fine structure techniques were used to analyze the surface and chemical composition of the photocatalyst,while thermogravimetric analysis,CO_(2) adsorption isotherm,and temperature programmed desorption study were performed to examine the significance of H_(2)O_(2) treatment in increasing CO_(2) reduction activity.The optimized Ag1.0@Ru1.0-P25 photocatalyst performed excellent CO_(2) reduction activity into CO,CH4,and C2H6 with a~95%selectivity of CH4,where the activity was~135 times higher than that of pristine TiO_(2)(P25).For the first time,this work explored the effect of H_(2)O_(2) treatment on the photocatalyst that dramatically increases CO_(2) reduction activity.