Differences of Polygonal Faults with Irregularly Polygonal Geometries: A Case Study from the Changchang Sag of Qiongdongnan Basin, Northern South China Sea

Polygonal faults(PFs)generally have a classic polygonal geometry in map view.However,under the influence of tectonic faults,diapirs,channels,and slopes,the classic polygonal geometry of PFs is not preserved,demonstrating differences(different characters)in map-view 3D seismic data covering an area of 334km^(2) of the Changchang(CC)sag,are used to document the mapview and cross-sectional characteristics of PFs.These data also help investigate the irregularly polygonal geometries of PFs due to the presence of influence factors,such as transtensional faults,submarine fans,channels,diapirs/gas chimneys,and the basal slope within the lower-middle Miocene strata.Results show that various irregularly polygonal geometries of PFs can be classified into enechelon and arcuate PFs,channel-segmenting and-bounding PFs,radial PFs,and rectangular PFs in map-view.En-echelon and arcuate PFs are induced by transtensional faults and exhibit a unique‘flower’structure in NE-and SE-trending cross-sections in the NW area of the study area.This finding is documented for the first time.Channel-segmenting PFs occur in the(northwest)low-amplitude muddy channel and are inhibited in the(southeast)high-amplitude sandy channel in the SW area.Radial PFs are radially aligned around a gas chimney/diapir containing some high-amplitude anomalies(HAAs)in the middle area.The presence of intrusive sandstones with HAAs along the periphery of the diapirs restricts the occurrence of PFs.Two high-amplitude submarine fans act as a mechanical barrier to the propagation of PFs.Meanwhile,the(moderate)slope in the NE area induces rectangular PFs.Additionally,the geneses of the PFs in the current study are comprehensively discussed.This study adds to our understanding of the differences between PFs with irregularly polygonal geometries.

Differences of polygonal faults related to upper Miocene channels:a case study from the Beijiao sag of Qiongdongnan basin,South China Sea

Deep-water coarse-grained channels are embedded within a polygonal fault tier,and the polygonal faults(PFs)present non-polygonal geometries rather than classic polygonal geometry in plan view.However,PFs present differences when they encounter deep-water(coarse-grained vs.fine-grained)channels with different lithology,which has not been further studied to date.Three-dimensional(3D)seismic data and a drilling well from Beijiao sag of Qiongdongnanbasin,South China Sea were utilized to document the plan view and cross-sectional properties of the PFs and their differences and genetic mechanism were investigated.Results show that,first,PFs can be divided morphologically into channel-segmenting PFs and channel-bounding PFs in plan view.The former virtually cuts or segments the axes of channels in highand low-amplitudes,and the latter nearly parallels the boundaries of the channels.Both are approximately perpendicular to each other.Secondly,channel-bounding PFs that related to low-amplitude channels are much longer than those of high-amplitude ones;channel-segmenting PFs related to low-amplitude channels are slightly longer than the counterparts related to high-amplitude channels.Lastly,the magnitudes(e.g.,heights)of the PFs are proportional to the scales(e.g.,widths and heights)of low-amplitude channels,whereas the magnitudes of the PFs are inversely proportional to the scales of high amplitude channels.Coarse-grained(high amplitude)channels act as a mechanical barrier to the propagation of PFs,whereas fine-grained(low-amplitude)channels are beneficial to the propagation and nucleation of PFs.Additionally,the genetic mechanism of PFs is discussed and reckoned as combined geneses of gravitational spreading and overpressure hydrofracture.The differences of the PFs can be used to reasonably differentiate coarse-grained channels from fine-grained channels.This study provides new insights into understanding the different geometries of the PFs related to coarse-grained and fine-grained channels and their genetic mechanism.

Drag Coefficient of a Non-Convex Polygonal Plate during Free Fall

Waterside creatures or aquatic organisms use a fin or web to generate a thrust force. These fins or webs have a non-convex section, referred to as a non-convex shape. We investigate the drag force acting on a non-convex plate during unsteady motion. We perform the experiment in a water tank during free fall. We fabricate the non-convex plate by cutting isosceles triangles from the side of a convex hexagonal plate. The base angle of the triangle is between 0° to 45°. The base angle is 0 indicates the convex hexagonal thin plate. We estimate the drag coefficient with the force balance acting on the model based on the image analysis technique. The results indicate that increasing the base angle by more than 30° increased the drag coefficient. The drag coefficient during unsteady motion changed with the growth of the vortex behind the model. The vortex has small vortices in the shear layer, which is related to the Kelvin-Helmholtz instabilities.

Radio-Anatomical Study of Anterior Variants of the Polygon of Willis

The anterior system of the polygon of Willis plays an anastomotic role between the carotid territories and communicates with the posterior system. It ensures adequate cerebral blood flow in the event of internal occlusion. Its ability to redistribute blood flow depends on its morphology, the presence and size of the vessels that constitute it and their variants, knowledge of which is essential. The morphology of the carotid system is not constant and a number of variants are well recognized with greater hemodynamic importance. In this context, we undertook this work which aims to seek the anatomical variants of the anterior part of the PW;to determine the diameters of the vessels of the latter and to correlate these results with epidemiological data. We carried out a retrospective, descriptive and analytical study over a period of 4 months at Fann University Hospital, targeting patients who had undergone brain MRI with a 3D TOF sequence whatever the indication. Patients with lesions of cerebrovascular pathologies such as ischemia, hemorrhage, aneurysm, arteriovenous malformations or presenting a limited analysis examination due to the presence of kinetic or other artifact, were not included. Demographic data and anatomical variants were studied as well as the measurements of any continuous arterial segment greater than 0.8 mm in diameter. Those less than 0.8 mm in diameter were considered hypoplastic. The C3 segment of the internal carotid arteries, the A1 segment of the anterior cerebral arteries, the anterior communicating artery, constituted our main measurement sites. The sex ratio was 1.06, the mean age of the patients was 43 years ± 17.9 with extremes of 11 and 85 years. The anterior configuration of the polygon was complete in 57.5% representing 50% of men and 65.5% of women, in 56% of subjects under 40 years old and 58% in subjects over 40 years old. We noted a predominance of type a in 47% of patients followed by type g found in 35% of patients. The morphology of the anterior system of the Willis polygon is a function of its variants, some of which have greater hemodynamic importance than others. Its knowledge is essential for the management of cerebrovascular diseases.

基于Polygon的雕塑法计算机辅助造型设计方法

计算机辅助设计技术已成为设计表现的必备手段,对于概念造型设计而言,接近传统手工方式的设计方法更易于被艺术设计师理解和接受。在对比目前主要计算机辅助造型方法的基础上,从分析传统手工雕塑造型的方式出发,针对概念设计和艺术造型设计的实际特征,提出了基于Polygon建模的雕塑法建模思路,给出了具体的建模步骤和合理布线的评价方法,并通过民间工艺品-泥塑马的造型实现过程进行了实例验证。实际运用证明,计算机雕塑建模方法对于艺术设计的三维软件建模理念具有较强的实用性,能够充分按照设计师的构思理念进行造型设计,对于创意设计而言更易于被造型设计师理解和运用。

Special properties of Eshelby tensor for a regular polygonal inclusion

When studying the regular polygonal inclusion in 1997, Nozaki and Taya discovered numerically some remarkable properties of Eshelby tensor： Eshelby tensor at the center and the averaged Eshelby tensor over the inclusion domain are equal to that of a circular inclusion and independent of the orientation of the inclusion. Then Kawashita and Nozaki justified the properties mathematically. In the present paper, some other properties of a regular polygonal inclusion are discovered. We find that for an N-fold regular polygonal inclusion except for a square, the arithmetic mean of Eshelby tensors at N rotational symmetrical points in the inclusion is also equal to the Eshelby tensor for a circular inclusion and independent of the orientation of the inclusion. Furthermore, in two corollaries, we point out that Eshelby tensor at the center, the averaged Eshelby tensor over the inclusion domain, and the line integral average of Eshelby tensors along any concentric circle of the inclusion are all identical with the arithmetic mean.

Study of CNC Grinding Machining Method About Isometric Polygon Profile

The formed principle and CNC grinding machining method of isometric polygonal profile are studied deeply and systematically. Equation about section curve of isometric polygon profile is set up by means of geometric principle. With the use of differential geometry theory, the curve is proved to be with geometric feature of convex curve. It is referred to as Isometric Polygonal Curve (IPC), because that is a kind of convex curve on which the distance between any parallel tangent lines is equal. Isometric Polygonal Profile (IPP) or Isometric Polygonal Cone Profile (IPCP) or Isometric Polygonal Topless Cone (IPTC) is formed with the IPC and straight line as generating curve. But the machining and measuring of the IPCP are so inconvenient that it has little value. Keeping in mind the characteristic of the IPP and IPTC, this paper puts forward the program method of CNC grinding machining. Isometric polygonal profile connection is a kind of polygonal profile connection. It has the superiority over keys (prismatic key & spline etc), and can be suit for the situations such as high rotative velocity, large torque, high precision, and small fixed room and vibration. Nowadays, some countries such as America, Russia, German and Switzerland applied CNC machining to the machining of polygon surface coupling parts, which makes their applications in machine productions such as motor engine, heavy machine increase day by day. But reports about concrete machining technology of isometric polygonal profile and programming of CNC machining program are very few. CNC grinding of the IPP and IPTC is one kind of the precision machining technology. It is of great importance to the popularization of the IPP and IPTC connection. From the forming mechanism, we can see that the machining and measuring of the IPP and IPTC are convenient, and therefore they have the value of the popularization. But the machining and measuring of the IPCP are so inconvenient that it has little value. In the programming the CNC grinding of the IPP and IPTC, it is more reasonable to calculate the coordinate of node according to the approaching method of equal error arc. According to the method of CNC grinding mentioned above to design the grinding machine, the structure is simple and of economical and practical.

A NEW METHOD FOR POINT-POLYGON CLASSIFICATION BASED ON POINT-EDGE COMPARISON

A new method for point-polygon classification is presented in the paper. The basic idea of the method is first advanced and then two properties of polygon are introduced. The criterions for point-polygon classification are given explicitly. The analysis shows that the possesses perfect function, extensive suitability and high efficiency.

Prediction and Control of Wrinkle and Fracture for Stamping Regular Polygonal Box

Based on the deformation characteristic of regular polygonal box stamped parts and the superfluous triangle material wrinkle model,the criterion of regular polygonal box stamped parts without wrinkle was deduced and used to predict and control the wrinkle limit.According to the fracture model,the criterion of regular polygonal box stamped parts without fracture was deduced and used to predict and control the fracture limit.Combining the criterion for stamping without wrinkle with that without fracture,the stamping criterion of regular polygonal box stamped parts was obtained to predict and control the stamping limit.Taken the stainless steel0Cr18Ni9(SUS304)sheet and the square box stamped part as examples,the limit diagram was given to predict and control the wrinkle,fracture and stamping limits.It is suitable for the deep drawing without flange,the deep drawing and stretching combined forming with flange and the rigid punch stretching of plane blank.The limit deep-drawing coefficient and the minimum deep-drawing coefficient can be determined,and the appropriate BHF(blank holder force)and the deep-drawing force can be chosen.These provide a reference for the technology planning,the die and mold design and the equipment determination,and a new criterion evaluating sheet stamping formability,which predicts and controls the stamping process,can be applied to the deep drawing under constant or variable BHF conditions.

基于Polygon之间相互切割的算法描述与实现

在地理信息系统(GIS)或一些图形处理中,经常会碰到地理图形切割,以及对切割后的数据进行处理。文章主要讨论了由Polygon切割Polygon生成Polygon算法的现实意义,以及如何实现切割后的Polygon自动生成算法的问题。

Experimental and Modeling Study of the Regular Polygon Angle-spiral Liner in Ball Mills

Load behavior is one of the most critical factors affecting mills＇ energy consumption and grinding efficiency, and is greatly affected by the liner profiles. Generally, as liner profiles vary, the ball mill performances are extremely different. In order to study the performance of the ball mill with regular polygon angle-spiral liners（RPASLs）, experimental and numerical studies on three types of RPASLs, including regular quadrilateral, pentagonal and hexagonal, are carried out. For the fine product of desired size, two critical parameters are analyzed： the energy input to the mill per unit mass of the fine product, E＊, and the rate of production of the fine product, F＊. Results show that the optimal structure of RPASLs is Quadrilateral ASL with an assembled angle of 50°. Under this condition, the specific energy consumption E＊ has the minimum value of 303 J per fine product and the production rate F＊ has the maximum value of 0.323. The production rate F＊ in the experimental result is consistent with the specific collision energy intensity to total collision energy intensity ratio Es/Et in the simulation. The relations between the production rate F＊ and the specific energy consumption E＊ with collision energy intensity Es and Et are obtained. The simulation result reveals the essential reason for the experimental phenomenon and correlates the mill performance parameter to the collision energy between balls, which could guide the practical application for Quadrilateral ASL.

Updating conventional soil maps by mining soil–environment relationships from individual soil polygons

Conventional soil maps contain valuable knowledge on soil–environment relationships.Such knowledge can be extracted for use when updating conventional soil maps with improved environmental data.Existing methods take all polygons of the same map unit on a map as a whole to extract the soil–environment relationship.Such approach ignores the difference in the environmental conditions represented by individual soil polygons of the same map unit.This paper proposes a method of mining soil–environment relationships from individual soil polygons to update conventional soil maps.The proposed method consists of three major steps.Firstly,the soil–environment relationships represented by each individual polygon on a conventional soil map are extracted in the form of frequency distribution curves for the involved environmental covariates.Secondly,for each environmental covariate,these frequency distribution curves from individual polygons of the same soil map unit are synthesized to form the overall soil–environment relationship for that soil map unit across the mapped area.And lastly,the extracted soil–environment relationships are applied to updating the conventional soil map with new,improved environmental data by adopting a soil land inference model(SoLIM)framework.This study applied the proposed method to updating a conventional soil map of the Raffelson watershed in La Crosse County,Wisconsin,United States.The result from the proposed method was compared with that from the previous method of taking all polygons within the same soil map unit on a map as a whole.Evaluation results with independent soil samples showed that the proposed method exhibited better performance and produced higher accuracy.

Optimal Polygonal Approximation of Digital Planar Curves Using Genetic Algorithm and Tabu Search

Three heuristic algorithms for optimal polygonal approximation of digital planar curves is presented. With Genetic Algorithm (GA), improved Genetic Algorithm (IGA) based on Pareto optimal solution and Tabu Search (TS), a near optimal polygonal approximation was obtained. Compared to the famous Teh chin algorithm, our algorithms have obtained the approximated polygons with less number of vertices and less approximation error. Compared to the dynamic programming algorithm, the processing time of our algorithms are much less expensive.

A COUNTER－EXAMPLE TO A FAST ALGORITHM FOR FINDING THE CONVEX HULL OF A SIMPLE POLYGON

A linear-time algorithm was recently published (International Conference Proceedings ofPacific Graphics' 94/CADDM' 94, August 26-29 , 1994 , Beijing , China) for computing the convexhull of a simple polygon. In this note we present a counter-example to that algorithm by exhibiting afamily of polygons for which the algorithm discards vertices that are on the convex hull.

A novel virtual node method for polygonal elements

A novel polygonal finite element method （PFEM） based on partition of unity is proposed, termed the virtual node method （VNM）. To test the performance of the present method, numerical examples are given for solid mechanics problems. With a polynomial form, the VNM achieves better results than those of traditional PFEMs, including the Wachspress method and the mean value method in standard patch tests. Compared with the standard triangular FEM, the VNM can achieve better accuracy. With the ability to construct shape functions on polygonal elements, the VNM provides greater flexibility in mesh generation. Therefore, several fracture problems are studied to demonstrate the potential implementation. With the advantage of the VNM, the convenient refinement and remeshing strategy are applied.

Ordering polygonal chains with respect to Hosoya index

The Hosoya index of a graph is defined as the total number of the matching of the graph. In this paper, the ordering of polygonal chains with respect to Hosoya index is characterized.

Stabilization for Equal-Order Polygonal Finite Element Method for High Fluid Velocity and Pressure Gradient

This paper presents an adapted stabilisation method for the equal-order mixed scheme of finite elements on convex polygonal meshes to analyse the high velocity and pressure gradient of incompressible fluid flows that are governed by Stokes equations system.This technique is constructed by a local pressure projection which is extremely simple,yet effective,to eliminate the poor or even non-convergence as well as the instability of equal-order mixed polygonal technique.In this research,some numerical examples of incompressible Stokes fluid flow that is coded and programmed by MATLAB will be presented to examine the effectiveness of the proposed stabilised method.

A new method of quality improvement for quadrilateral mesh based on small polygon reconnection

In this paper, a new method of topological cleanup for quadrilateral mesh is presented. The method first selects a patch of mesh around an irregular node. It then seeks the best connection of the selected patch according to its irregular valence using a new topological operation： small polygon reconnection （SPR）. By replacing the original patch with an optimal one that has less irregular valence, mesh quality can be improved. Three applications based on the proposed approach are enumerated： （1） improving the quality of a quadrilateral mesh, （2） converting a triangular mesh to a quadrilateral one, and （3） adapting a triangle generator to a quadrilateral one. The presented method is highly effective in all three applications.

Quantitative detection of locomotive wheel polygonization under non-stationary conditions by adaptive chirp mode decomposition

Wheel polygonal wear is a common and severe defect,which seriously threatens the running safety and reliability of a railway vehicle especially a locomotive.Due to non-stationary running conditions(e.g.,traction and braking)of the locomotive,the passing frequencies of a polygonal wheel will exhibit time-varying behaviors,which makes it too difficult to effectively detect the wheel defect.Moreover,most existing methods only achieve qualitative fault diagnosis and they cannot accurately identify defect levels.To address these issues,this paper reports a novel quantitative method for fault detection of wheel polygonization under non-stationary conditions based on a recently proposed adaptive chirp mode decomposition(ACMD)approach.Firstly,a coarse-to-fine method based on the time–frequency ridge detection and ACMD is developed to accurately estimate a time-varying gear meshing frequency and thus obtain a wheel rotating frequency from a vibration acceleration signal of a motor.After the rotating frequency is obtained,signal resampling and order analysis techniques are applied to an acceleration signal of an axle box to identify harmonic orders related to polygonal wear.Finally,the ACMD is combined with an inertial algorithm to estimate polygonal wear amplitudes.Not only a dynamics simulation but a field test was carried out to show that the proposed method can effectively detect both harmonic orders and their amplitudes of the wheel polygonization under non-stationary conditions.

No Fit Polygon for Nesting Problem Solving with Hybridizing Ant Algorithms

In design science, these two kinds of problems are mutually nested, however, the nesting could not blind us for the fact that their problem-solving and solution justification methods are different. The ant algorithms research field, builds on the idea that the study of the behavior of ant colonies or other social insects is interesting, because it provides models of distributed organization which could be utilized as a source of inspiration for the design of optimization and distributed control algorithms. In this paper, a relatively new type of hybridizing ant search algorithm is developed, and the results are compared against other algorithms. The intelligence of this heuristic approach is not portrayed by individual ants, but rather is expressed by the colony as a whole inspired by labor division and brood sorting. This solution obtained by this method will be evaluated against the one obtained by other traditional heuristics.