Comparative impact behaviours of ultra high performance concrete columns reinforced with polypropylene vs steel fibres

Polypropylene(PP) fibres have primarily used to control shrinkage cracks or mitigate explosive spalling in concrete structures exposed to fire or subjected to impact/blast loads, with limited investigations on capacity improvement. This study unveils the possibility of using PP micro-fibres to improve the impact behaviour of fibre-reinforced ultra-high-performance concrete(FRUHPC) columns. Results show that the addition of fibres significantly improves the impact behaviour of FRUHPC columns by shifting the failure mechanism from brittle shear to favourable flexural failure. The addition of steel or PP fibres affected the impact responses differently. Steel fibres considerably increased the peak impact force(up to 18%) while PP micro-fibres slightly increased the peak(3%-4%). FRUHPC significantly reduced the maximum midheight displacement by up to 30%(under 20°impact) and substantially improved the displacement recovery by up to 100%(under 20° impact). FRUHPC with steel fibres significantly improved the energy absorption while those with PP micro-fibres reduced the energy absorption, which is different from the effect of PP-macro fibre reported in the literature. The optimal fibre content for micro-PP fibres is 1% due to its minimal fibre usage and low peak and residual displacement. This study highlights the potential of FRUHPC as a promising material for impact-resistant structures by creating a more favourable flexural failure mechanism, enhancing ductility and toughness under impact loading, and advancing the understanding of the role of fibres in structural performance.

Exploring the effect of cooling rate on non-isothermal crystallization of copolymer polypropylene by fast scanning calorimetry

Polypropylene is commonly used as a binder for ceramic injection molding,and rapid cooling is often encountered during processing.However,the crystallization behavior of polypropylene shows a strong dependence on cooling rate due to its semi-crystalline characteristics.Therefore,the influence of cooling rate on the quality of final product cannot be ignored.In this study,the fast differential scanning calorimetry(FSC)test was performed to study the influence of cooling rate on the non-isothermal crystallization behavior and non-isothermal crystallization kinetics of a copolymer polypropylene(PP BC03B).The results show that the crystallization temperatures and crystallinity decrease as the cooling rate increases.In addition,two exothermic peaks occur when cooling rate ranges from 30 to 300 K·s^(-1),indicating the formation of another crystal phase.Avrami,Ozawa and Mo equations were used to explore the non-isothermal crystallization kinetics,and it can be concluded that the Mo method is suitable for this study.

Effects of cement content, polypropylene fiber length and dosage on fluidity and mechanical properties of fiber-toughened cemented aeolian sand backfill

Using aeolian sand(AS)for goaf backfilling allows coordination of green mining and AS control.Cemented AS backfill(CASB)exhibits brittle fracture.Polypropylene(PP)fibers are good toughening materials.When the toughening effect of fibers is analyzed,their influence on the slurry conveying performance should also be considered.Additionally,cement affects the interactions among the hydration products,fibers,and aggregates.In this study,the effects of cement content(8wt%,9wt%,and 10wt%)and PP fiber length(6,9,and 12 mm)and dosage(0.05wt%,0.1wt%,0.15wt%,0.2wt%,and 0.25wt%)on fluidity and mechanical properties of the fibertoughened CASB(FCASB)were analyzed.The results indicated that with increases in the three aforementioned factors,the slump flow decreased,while the rheological parameters increased.Uniaxial compressive strength(UCS)increased with the increase of cement content and fiber length,and with an increase in fiber dosage,it first increased and then decreased.The strain increased with the increase of fiber dosage and length.The effect of PP fibers became more pronounced with the increase of cement content.Digital image correlation(DIC)test results showed that the addition of fibers can restrain the peeling of blocks and the expansion of fissure,and reduce the stress concentration of the FCASB.Scanning electron microscopy(SEM)test indicated that the functional mechanisms of fibers mainly involved the interactions of fibers with the hydration products and matrix and the spatial distribution of fibers.On the basis of single-factor analysis,the response surface method(RSM)was used to analyze the effects of the three aforementioned factors and their interaction terms on the UCS.The influence surface of the two-factor interaction terms and the three-dimensional scatter plot of the three-factor coupling were established.In conclusion,the response law of the FCASB properties under the effects of cement and PP fibers were obtained,which provides theoretical and engineering guidance for FCASB filling.

Efficient and selective removal of Pb(Ⅱ) from landfill leachate using L-serine-modified polyethylene/polypropylene nonwoven fabric synthesized via radiation grafting technique

In this study,to efficiently remove Pb(Ⅱ) from aqueous environments,a novel L-serine-modified polyethylene/polypropylene nonwoven fabric sorbent(NWF-serine)was fabricated through the radiation grafting of glycidyl methacrylate and subsequent L-serine modification.The effect of the absorbed dose was investigated in the range of 5–50 kGy.NWF-serine was characterized by Fourier transform infrared spectroscopy,thermogravimetric analysis,and scanning electron microscopy.Batch adsorption tests were conducted to investigate the influences of pH,adsorption time,temperature,initial concentration,and sorbent dosage on the Pb(Ⅱ) adsorption performance of NWF-serine.The results indicated that Pb(Ⅱ) adsorption onto NWF-serine was an endothermic process,following the pseudo-second-order kinetic model and Langmuir isotherm model.The saturated adsorption capacity was 198.1 mg/g.NWF-serine exhibited Pb(Ⅱ) removal rates of 99.8% for aqueous solutions with initial concentrations of 100 mg/L and 82.1% for landfill leachate containing competitive metal ions such as Cd,Cu,Ni,Mn,and Zn.Furthermore,NWF-serine maintained 86% of its Pb(Ⅱ) uptake after five use cycles.The coordination of the carboxyl and amino groups with Pb(Ⅱ) was confirmed using X-ray photoelectron spectroscopy and extended X-ray absorption fine structure analysis.

Characterization and Modeling of Mechanical Properties of Additively Manufactured Coconut Fiber-Reinforced Polypropylene Composites

In the face of the increased global campaign to minimize the emission of greenhouse gases and the need for sustainability in manufacturing, there is a great deal of research focusing on environmentally benign and renewable materials as a substitute for synthetic and petroleum-based products. Natural fiber-reinforced polymeric composites have recently been proposed as a viable alternative to synthetic materials. The current work investigates the suitability of coconut fiber-reinforced polypropylene as a structural material. The coconut fiber-reinforced polypropylene composites were developed. Samples of coconut fiber/polypropylene (PP) composites were prepared using Fused Filament Fabrication (FFF). Tests were then conducted on the mechanical properties of the composites for different proportions of coconut fibers. The results obtained indicate that the composites loaded with 2 wt% exhibited the highest tensile and flexural strength, while the ones loaded with 3 wt% had the highest compression strength. The ultimate tensile and flexural strength at 2 wt% were determined to be 34.13 MPa and 70.47 MPa respectively. The compression strength at 3 wt% was found to be 37.88 MPa. Compared to pure polypropylene, the addition of coconut fibers increased the tensile, flexural, and compression strength of the composite. In the study, an artificial neural network model was proposed to predict the mechanical properties of polymeric composites based on the proportion of fibers. The model was found to predict data with high accuracy.

The Effect of Silane Grafted Polypropylente on the Property of Different Filler/Polypropylene Composites

Aim To determine the effect of silane grafted polypropylene on the property of different filler/polypropylene composites. Methods Polypropylene (PP) composites filled with talc(Ta), baryta sulfate and calcium carbonate coupled with silane grafted polypropylene (PP-g-Si) were made, their mechanical properties and thermal properties were investigated, respectively. Results As compared with the non-coupled composites, the mechanical properties of PP/Ta/PP-g-Si composites were improved to some extent, though the values of tensile modulus and the strain at peak were decreased. But for PP/BaSO4 and PP/CaCO3 composites, the values of their mechanical properties varied slightly or even decreased with increasing PP-g-Si content within the experimental component. Meanwhile, PP-g-Si also affected the melting and crystallization behavior of PP in the composites. Conclusion PP-g-Si offers compatibilization in PP/Ta composites, but offers no-compatibilization in PP/BaSO4 and PP/CaCO3 composites within the extent of the present range of PP-g-Si, which shows that PP-g-Si can be used as the macromolecular coupling agent of PP and Ta composite.

Enhance of Grafting Reaction of Acrylic Acid and Acrylamide onto Preirradiated Polypropylene Film

Grafting of acrylic acid (AAc) and acrylamide (AAm) onto preirradiated PP film was performed in aqueous solution of AAc and AAm, respectively. Electron beam accelerator was used as irradiation source. The effect of ferrous sulfate, sodium nitrate, methanol and glucose on the degree of grafting was demonstrated. The function of the different additives was compared by the grafting of different monomers (AAc and AAm). The results show that the four of these additives are elective on the grafting of AAc. Only two of these additives, ferrous sulfate and methanol were effective on the grafting of AAm.

医用丝线和Polypropylene缝线用于皮肤除皱的对比研究

目的:研究临床常用外科缝线医用丝线和在国外用于皮肤提升除皱术中的常用Polypropylene缝线对皮肤胶原蛋白的影响。方法:将21只造模成功的衰老家兔随机分为三组,即Polypropylene缝线(P)组、医用丝线(S)组和空白对照组。在缝线植入术后第3、7、15、30、45、60及90天切取P组和S组手术标记区及对照组取样区皮肤,做羟脯氨酸(HYP)的含量测定。结果:P组、S组和对照组在不同时间点测得的HYP含量差异有统计学意义(P<0.05)。测定时点与手术分组存在交互作用(P<0.05)。HYP含量为P组>S组>对照组。结论:Polypropylene缝线比医用丝线能更为有效的改善皮肤弹性和皱纹。

Preliminary study of viscoelastic properties of MAPP-modified wood flour/polypropylene composites

Viscoelastic properties of maleated polypropylene （MAPP）-modified wood flour/polypropylene composites （WPC） were investigated by both a compression stress relaxation method and dynamic mechanical analyses （DMA）. Three wood to polymer ratios （40：60, 60：40, and 80：20） and five MAPP loading levels （0, 1, 2, 4 and 8%） were used to study their effects on the viscoelastic prop- erties of MAPP-WPC. The results show that： 1） higher wood to polymer ratio corresponds to higher stress relaxation levels for unmodified WPC. The modification with MAPP has an obvious effect on the stress relaxation of MAPP-WPC at higher wood to polymer ratios （60：40 and 80：20）, but almost no effect at the 40：60 wood to polymer ratio. The optimal MAPP loading level for the wood to polymer ratio of 60：40 appears at 1%; 2） the storage modulus reaches its maximum at a MAPP loading level of 1% for wood to polymer ratios of 40：60 and 60：40, while for the 80：20 wood to polymer ratio, a higher storage modulus is observed at higher MAPP loading levels, which is quite consistent with the stress relaxation results. The results suggested that a suitable loading level of MAPP has a positive effect on the viscoelastic properties of WPC at higher wood to polymer ratios. Excessive MAPP loading would have resulted in adverse effects.

医用丝线和Polypropylene缝线对植入部位皮肤衰老因子影响的实验研究

目的通过衰老动物模型研究临床常用外科缝线医用丝线和皮肤提升除皱术中的常用聚丙烯缝线(Polypropylene缝线)对皮肤抗衰老指标的影响,探讨手术缝线对皮肤除皱的机制。方法将21只造模成功的衰老家兔随机分为三组,并于缝线植入术后第3,7,15,30,45,60,90天切取手术标记区及对照组取样区皮肤,测定皮肤组织中超氧化物歧化酶(SOD)的活性及过氧化氢(H2O2)的含量。结果缝线植入组和对照组在不同时间点测得的SOD及H2O2含量差异有统计学意义(P<0.05)。测定时点与手术分组存在交互作用(P<0.05)。结论植入缝线可以起到一定的抗衰老作用,Polypropylene缝线比医用丝线能更为有效地改善皮肤弹性和皱纹。

Fracture Properties of Cement Composites Reinforced with Steel Polypropylene Hybrid Fibres

Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.

Effect of maleic anhydride grafted styrene-ethylene-butylene-styrene （MA-SEBS） on impact fracture behavior of polypropylene / wood fiber composites

MA-SEBS as compatibilizer and impact modifier was incorporated into Polypropylene/Wood Fiber （PP/WF） to enhance interface adhesion and impact strength of the composite. The effect of MA-SEBS content on the impact fracture behavior of PP/WF composites was studied. The impact properties of composites with 8% MA-SEBS reached the maximum value. And further increasing of MA-SEBS content to 10% did not improve the fracture toughness, but improved the stiffness of composites by DMA analysis. This was attributed to the improved PP/WF adhesion. As the MA-SEBS content is more than 8%, the molecule interaction of PP and WF was expected to much stronger than lower MA-SEBS. Scanning electron microscopy （SEM） was performed to analyze the impact fracture surface and showed a stronger affinity for the wood surfaces.

Catalytic performances of kaoline and silica alumina in the thermal degradation of polypropylene

Polypropylene was cracked thermally and catalytically in the presence of kaoline and silica alumina in a semi batch reactor in the temperature range 400℃～550℃ in order to obtain suitable liquid fuels.The dependencies between process temperatures,types of catalyst,feed compositions and product yields of the obtained fuel fractions were found.It was observed that up to 450℃ thermal cracking temperature,the major product of pyrolysis was liquid oil and the major product at other higher temperatures(475℃～550℃) are viscous liquid or wax and the highest yield of pyrolysis product is 82.85% by weight at 500℃.Use of kaoline and silica alumina decreased the reaction time and increased the yield of liquid fraction.Again the major pyrolysis product in catalytic pyrolysis at all temperatures was low viscous liquid oil.Silica alumina was found better as compared to kaoline in liquid yield and in reducing the reaction temperature.The maximum oil yield using silica alumina and kaoline catalyst are 91% and 89.5% respectively.On the basis of the obtained results hypothetical continuous process of waste polypropylene plastics processing for engine fuel production can be presented.

Multivariate Statistical Process Monitoring of an Industrial Polypropylene Catalyzer Reactor with Component Analysis and Kernel Density Estimation

Abstract Data-driven tools, such as principal component analysis （PCA） and independent component analysis （ICA） have been applied to different benchmarks as process monitoring methods. The difference between the two methods is that the components of PCA are still dependent while ICA has no orthogonality constraint and its latentvariables are independent. Process monitoring with PCA often supposes that process data or principal components is Gaussian distribution. However, this kind of constraint cannot be satisfied by several practical processes. To ex-tend the use of PCA, a nonparametric method is added to PCA to overcome the difficulty, and kernel density estimation （KDE） is rather a good choice. Though ICA is based on non-Gaussian distribution intormation, .KDE can help in the close monitoring of the data. Methods, such as PCA, ICA, PCA.with .KDE（KPCA）, and ICA with KDE,（KICA）, are demonstrated and. compared by applying them to a practical industnal Spheripol craft polypropylene catalyzer reactor instead of a laboratory emulator.

Effect of Oleic Acid-modified Nano-CaCO3 on the Crystallization Behavior and Mechanical Properties of Polypropylene

Oleic acid (OA)-modified CaCO3 nanoparticles were prepared using surface modification method. Infrared spectroscopy (IR) was used to investigate the structure of the modified CaCO3 nanoparticles, and the result showed that OA attached to the surface of CaCO3 nanoparticles with the ionic bond. Effect of OA concentration on the dispersion stability of CaCO3 in heptane was also studied, and the result indicated that modified CaCO3 nanoparticles dispersed in heptane more stably than unmodified ones. The optimal proportion of OA to CaCO3 was established. The effect of modified CaCO3 nanoparticles on crystallization behavior of polypropylene (PP) was studied by means of DSC. It was found that CaCO3 significantly increased the crystallization temperature, crystallization degree and crystallization rate of PP, and the addition of modified CaCO3 nanoparticles can lead to the formation of β-crystal PP. Effect of the modified CaCO3 content on mechanical properties of PP/CaCO3 nanocomposites was also studied. The results showed that the modified CaCO3 can effectively improve the mechanical properties of PP. In comparison with PP, the impact strength of PP/CaCO3 nanocomposites increased by about 65% and the flexural strength increased by about 20%.

Preparation and mechanical properties of polypropylene fiber reinforced calcined kaolin-fly ash based geopolymer

To improve the environmental benefits and solve the problems of large shrinkage and high brittleness, the partial replacement of calcined kaolin by fly ash as a raw material for geopolymer synthesis and the influences of polypropylene (PP) fiber on the mechanical properties and volume stability were investigated. The results show that compressive strength of the geopolymer containing 33.3%(mass fraction) fly ash by steam curing at 80 ℃ for 6 d is improved by 35.5%. The 3-day compressive strength, flexural strength and impacting energy of geopolymers containing 0.05%PP fiber increase by 67.8%, 36.1% and 6.25%, while the shrinkage and modulus of compressibility decrease by 38.6% and 31.3%, respectively. The results of scanning electron microscopy (SEM) and the appearances of crack growths confirm that PP fiber can offer a bridging effect over the harmful pores and defects and change the expanding ways of cracks, resulting in a great improvement of strength and toughness.

Study on the Properties of Microcapsulated Chlorocyclophosphazene Polypropylene Composites

Microcapsulated chlorocyclophosphazenes were synthesized,and then microcapsulated chlorocyclo- phosphazene/polypropylene(PP)composites were prepared.The results showed that microcapsulated chlorocyclo- phosphazene had good high thermal stability through thermogravimetric analysis(TGA).The flammability and mechanical properties of microcapsulated chlorocyclophosphazene/polypropylene composites were investigated by limiting oxygen index experiment,UL 94V flame retardancy test,cone calorimetry,tensile experiment,and impact test,respectively.It was shown that the microcapsulated chlorocyclophosphazene/PP composites had better tensile strength,impact strength,flame retardant properties and smoke suppress properties compared with chlorocyclo- phosphazene/PP composites.

One-step synthesis of hydrophobic magnesium hydroxide nanoparticles and their application in flame-retardant polypropylene composites

Hydrophobic magnesium hydroxide(MH) nanoparticles were prepared by a one-step synthesis method in a high-gravity environment generated by a novel impinging stream–rotating packed bed(IS-RPB) reactor. The reactant solutions were simultaneously and continuously pumped into the IS-RPB reactor, and then Tween80 was added as a surface modifier. The morphology, structure, and properties of blank and hydrophobic MH were characterized. The effects of MH nanoparticles on the flame retardancy, thermal stability, and mechanical properties of PP/MH composites were also studied. We found that the obtained MH nanoparticles exhibited hexagonal lamella with a mean size of 30 nm, excellent hydrophobic properties(e.g., high water contact angle of 112°), and improved thermal stability of MH. The limiting oxygen index(LOI) further showed that increased MH loading can significantly improve flame-retardant performance, which reached 29.3% for PP/MH composites with 30 wt% hydrophobic samples. The thermal stability and mechanical properties of the PP/MH composites with hydrophobic samples were also much higher than those of PP/MH composites with blank MH. Results showed that the one-step synthesis had high potential application in the large-scale production of hydrophobic MH nanoparticles.

Effect of chemical modification on the properties of wood/polypropylene composites

Aluminate-based coupling agent was added as a compatibilizer to make the chemical modification of wood powder. The mechanical properties and morphology of wood powder/polypropylene composites were studied. The results showed that the compatibilizer can increase the impact strength of the wood/polypropylene composites, but it has a slightly negative effect on the tensile and flexural strength. For dynamic mechanical properties and Differential Scanning Calorimetry, Aluminate-based coupling agent can slightly increase the storage modulus and loss modulus, and decrease the melt point and the Calorie of Melt. Scanning electron microscopy showed that Aluminate-based coupling agent had a stronger affinity between the wood and polypropylene surfaces. These results suggested that Aluminate-based coupling agent may play a useful role in improving wood powder/polypropylene composites properties.

Effect of polypropylene fiber and coarse aggregate on the ductility and fluidity of cemented tailings backfill

Adding polypropylene(PP)fibers and coarse aggregates has become a popular way to enhance the strength and stability of the cemented tailings backfilling(CTB)body.It is essential to explore the influence of tailings-aggregate ratio and fiber content on the mechanical properties of CTB samples.The comprehensive tests of the unconfined compressive strength(UCS),slump and microstructure were designed,and the regression models were established to characterize the effect of the strength,ductility and fluidity.The results indicate that the tailings-aggregate ratio of 5:5 and PP fiber content of 0.5 kg/m^(3) are the optimum point considering the UCS,cracking strain,peak strain and post-peak ductility.The tailings-aggregate ratio is consistent with the unary quadratic to the UCS and a linear model with a negative slope to the slump.Microstructural analysis indicates that PP fiber tends to bridge the cracks and rod-mill sand to serve as the skeleton of the paste matrix,which can enhance the compactness and improve the ductility of the CTB.The results presented here are of great significance to the understanding and application of coarse aggregates and fibers to improve the mechanical properties of CTB.