Propagation Properties of Shock Waves in Polyurethane Foam based on Atomistic Simulations

Porous materials are widely used in the field of protection because of their excellent energy absorption characteristics.In this work,a series of polyurethane microscopic models are established and the effect of porosity on the shock waves is studied with classical molecular dynamics simulations.Firstly,shock Hugoniot relations for different porosities are obtained,which compare well with the experimental data.The pores collapse and form local stress wave,which results in the complex multi-wave structure of the shock wave.The microstructure analysis shows that the local stress increases and the local velocity decreases gradually during the process of pore collapse to complete compaction.Finally,it leads to stress relaxation and velocity homogenization.The shock stress peaks can be fitted with two exponential functions,and the amplitude of attenuation coefficient decreases with the increase of density.Besides,the pore collapse under shock or non-shock are discussed by the entropy increase rate of the system.The energy is dissipated mainly through the multiple interactions of the waves under shock.The energy is dissipated mainly by the friction between atoms under non-shock.

Experimental investigation on weak shock wave mitigation characteristics of flexible polyurethane foam and polyurea

In recent years,explosion shock wave has been considered as a signature injury of the current military conflicts.Although strong shock wave is lethal to the human body,weak shock wave can cause many more lasting consequences.To investigate the protection ability and characteristics of flexible materials and structures under weak shock wave loading,the blast wave produced by TNT explosive is loaded on the polyurethane foam with the density of 200.0 kg/m3(F-200)and 400.0 kg/m3(F-400),polyurea with the density of 1100.0 kg/m^(3)(P-1100)and structures composed of the two materials,which are intended for individual protection.Experimental results indicate that the shock wave is attenuated to weak pressure disturbance after interacting with the flexible materials which are not damaged.The shock wave protective capability of single-layer materials is dependent on their thickness,density and microscopic characteristics.The overpressure,maximum pressure rise rate and impulse of transmitted wave decrease exponentially with increase in sample thickness.For the same thickness,F-400 provides better protective capability than F-200 while P-1100 shows the best protective capability among the three materials.In this study,as the materials are not destroyed,F-200 with a thickness more than10.0 mm,F-400 with a thickness more than 4.0 mm,and P-1100 with a thickness more than 1.0 mm can attenuate the overpressure amplitude more than 90.0%.Further,multi-layer flexible composites are designed.Different layer layouts of designed structures and layer thickness of the single-layer materials can affect the protective performance.Within the research range,the structure in which polyurea is placed on the impact side shows the optimal shock wave protective performance,and the thicknesses of polyurea and polyurethane foam are 1.0 mm and 4.0 mm respectively.The overpressure attenuation rate reached maximum value of 93.3%and impulse attenuation capacity of this structure are better than those of single-layer polyurea and polyurethane foam with higher areal density.

Mechanical properties of foamed polyurethane solidified ballasted track

Foamed Polyurethane Solidified Ballasted Track(FPSBT),an innovative railway track,is formed by solidifying ballast bed with foamed polyurethane.Compared with the traditional Discrete Ballasted Track(DBT),FPSBT does not require regular maintenance such as tamping and cleaning.However,limited studies exist on the mechanical properties of FPSBT.In this study,Laboratory experiments are conducted on polyurethane samples to investigate the effects of polyurethane density on the mechanical properties of FPSBT.Furthermore,the performance of DBT and FPSBT with different polyurethane densities are compared,and the recommended polyurethane density is obtained.FPSBT exhibited negligible accumulation of deformation under cyclic loads,indicating excellent performance of FPSBT owing to the anti-deformation properties of polyurethane.Further,a track load vehicle test is conducted.FPSBT exhibited better load-transmitting ability than DBT.Finally,the construction and application of FPSBT in China are introduced.This study is expected to contribute to realizing a more extensive application of FPSBT.

Improving the Sound Absorption Properties of Flexible Polyurethane (PU) Foam using Nanofibers and Nanoparticles

Polyurethane foam as the most well-known absorbent materials has a suitable absorption coefficient only within a limited frequency range.The aim of this study was to improve the sound absorption coefficient of flexible polyurethane(PU)foam within the range of various frequencies using clay nanoparticles,polyacrylonitrile nanofibers,and polyvinylidene fluoride nanofibers.The response surface method was used to determine the effect of addition of nanofibers of PAN and PVDF,addition of clay nanoparticles,absorbent thickness,and air gap on the sound absorption coefficient of flexible polyurethane foam(PU)across different frequency ranges.The absorption coefficient of the samples was measured using Impedance Tubes device.Nano clay at low thicknesses as well as polyacrylonitrile nanofibers and polyvinyl fluoride nanofibers at higher thicknesses had a greater positive effect on absorption coefficient.The mean sound absorption coefficient in the composite with the highest absorption coefficient at middle and high frequencies was 0.798 and 0.75,respectively.In comparison with pure polyurethane foam with the same thickness and air gap,these values were 2.22 times at the middle frequencies and 1.47 times at high frequencies,respectively.Surface porosity rose with increasing nano clay,but decreased with increasing polyacrylonitrile nanofibers and polyvinyl fluoride nanofibers.The results indicated that the absorption coefficient was elevated with increasing the thickness and air gap.This study suggests that the use of a combination of nanoparticles and nanofibers can enhance the acoustic properties of flexible polyurethane foam.

超临界CO_(2)制备TPU/SiO_(2)复合泡沫及其性能研究

采用热塑性聚氨酯弹性体(TPU)作为基体,纳米二氧化硅(SiO_(2))充当填料,超临界二氧化碳(scCO_(2))为发泡剂,通过简单的物理共混的方式以及scCO_(2)发泡设备制备了TPU/SiO_(2)复合发泡材料;探究了不同SiO_(2)含量对复合发泡材料的影响.结果表明,纳米SiO_(2)粒子在TPU基体中有良好的分散性,所制备的TPU/SiO_(2)复合发泡材料混合均匀;纳米SiO_(2)粒子的添加调控了复合材料的发泡行为,使其泡孔尺寸稳定、分布范围从60~180μm下降至20~40μm.SiO_(2)粒子有效提高了TPU基体的结晶性,从而使得回弹从40上升至42,硬度从45.3 Shore C上升至54.38 Shore C;抗张强度从1.18 MPa上升至4.19 MPa,断裂伸长率从237.25%上升至460.03%.

PU发泡技术在现代家具中的应用及工艺解析

PU(聚氨酯)发泡技术在家具业应用非常广泛,泡沫塑料是近年来发展最快的工业塑料之一,主要应用于沙发和座椅、靠背垫、床垫和枕头以及仿木家具等的制造。本文以仿木家具为例,进行发泡工艺解析,以期为行业发展提供一些参考。

不同类型TPU的共混改性及其超临界发泡行为特征研究

以聚酯型和聚醚型不同类型热塑性聚氨酯(TPU)为考察对象,通过共混改性并采用超临界发泡技术制备了鞋用TPU复合发泡材料。研究了不同共混比例对复合材料官能团结构、熔体流动性,以及复合发泡材料的微观形貌结构、密度和发泡倍率的影响。结果表明,不同类型TPU共混后化学结构并未发生明显变化;随着聚醚TPU比例的增加,复合材料热稳定性略有降低,但其熔融指数提高;复合发泡材料泡孔为闭孔结构且孔径先增大后缩小并趋于均匀,密度先减小后增加,发泡倍率先增加后减小。当聚酯TPU与聚醚TPU共混比例为30∶70时,复合发泡材料密度最轻且达到0.132 g/cm^(3),发泡倍率最大且达到9.86倍。聚酯TPU与聚醚TPU二者在超临界发泡成型时存在协同作用。

基于改性竹粉/TPU复合发泡材料的制备及其发泡行为研究

以热塑性聚氨酯(TPU)为主基体,改性竹粉为填料,采用超临界发泡技术制备了鞋用TPU复合发泡材料。研究了不同改性竹粉含量对复合发泡材料形貌结构、热稳定性、熔体流动性、密度、发泡倍率的影响。结果表明,当添加改性竹粉后,复合发泡材料的微观泡孔形貌特征为闭孔结构;随着竹粉添加量的增加,并泡情况减少,孔径逐渐减小并逐渐趋于均一;在一定范围内,随着改性竹粉添加量的增加,复合材料的起始分解温度不变,熔点降低,熔融指数呈现上升趋势;当改性竹粉的添加量为5 phr时,复合发泡材料的密度最轻且达到0151 g/cm3,发泡倍率最大且达到855。

Performance characterization, of rigid polyurethane foam with refined alkali lignin and modified alkali lignin

The two kinds of rigid polyurethane （PU） foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight. The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams. The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples. The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently. Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples. The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.

Numerical study of forward smoldering combustionof polyurethane foam

A two-dimensional and two-phase numerical model is presented for the smolder propagation in a horizontal polyurethane foam. The chemical processes considered include endothermic pyrolysis and exotherrnic oxidation degradation of polyurethane foam and exothermic oxidation of char. The governing equations are discretized in space using the finite element method and solved by the software package FEMLAB. Predicted profiles of solid temperature as well as evolutions of solid compositions （including foam, char and ash） are presented at an airflow velocity of 0. 28 cm/s. The computed average smoldering velocity is 0. 021 4 cm/s, and the average maximum temperature is 644. 67 K. Based on the evolutions of solid compositions, the packed bed can be obviously divided into four zones： unreacted zone, fuel pyrolysis and oxidation zone, char oxidation zone and fuel burned-out zone. Simultaneously, the effects of inlet air velocity and fuel properties （including thermal conductivity, specific heat, density and pore diameter） are studied on the smoldering propagation. The results show that the smoldering velocity and temperature have a roughly linear increase with increasing inlet air velocity; the fuel density is the most important factor in determining smoldering propagation; radiation has a non-negligible role on the smoldering velocity for larger pore diameters of porous material. The computational results are compared with the experimental data and a general agreement is reached.

SBS/PU复合改性沥青混合料性能试验研究

【目的】研究苯乙烯-丁二烯-苯乙烯嵌段共聚物(styrene-butadiene-styrene block copolymer,SBS)与聚氨酯(polyurethane,PU)复合改性沥青混合料的路用性能。【方法】采用2.0%SBS与不同掺量(4.0%、6.0%、8.0%)的PU制备复合改性沥青,并使用这种改性沥青制备密级配沥青混合料AC-13,通过开展马歇尔试验、车辙试验、低温弯曲蠕变试验评价沥青混合料的高温抗车辙、低温抗裂、水稳定性,同时制备4.0%SBS改性沥青混合料和6.0%PU改性沥青混合料作为对照组。【结果】SBS/PU复合改性沥青混合料能够满足沥青路面的路用性能要求。其中,2.0%SBS+6.0%PU复合改性沥青混合料的动稳定度较基质沥青混合料、4.0%SBS改性沥青混合料、6.0%PU改性沥青混合料的分别提升144%、19%、52%,SBS/PU复合改性沥青混合料的高温稳定性较对照组有所提升,水稳定性与对照组相当,低温性能的改善效果不明显。【结论】综合考虑改性效果和经济性,SBS/PU复合改性沥青混合料的最佳掺量为2.0%SBS+6.0%PU。

Development of polyurethane foam dressing containing silver and asiaticoside for healing of dermal wound

Polyurethane foam dressings for dermal wounds were formulated with natural polyols in order to improve the foam characteristics and the release of 2 active agents,silver and asiaticoside(AS)as an antimicrobial agent and an herbal wound healing agent,respectively.The foam was instantly formed by interaction of polyols and diisocyanate.Hydroxypropyl methylcellulose,chitosan and sodium alginate were individually mixed with themain polyols,polypropylene glycol,in the formulation while the active componentswere impregnated into the obtained foam dressing sheets.Although the type and amount of the natural polyols slightly affected the pore size,water sorption-desorption profile and compression strength of the obtained foam sheets,a prominent effect was found in the release of both active components.Among natural polyols formulations,foam sheets with alginate showed the highest silver and AS release.Non-cytotoxicity of these foam sheets to human fibroblast cells was confirmed.Antimicrobial testing on four bacteria strains showed that 1mg/cm^2 silver in formulations with 6%of natural polyols and without natural polyols had sufficient content of the silver release with comparable inhibition zone and significantly larger zone than other formulations.In pig study,the foam dressing with 6%alginate,1mg/cm^2 silver and 5%AS could improve wound healing in both the percentage of the wound closure and histological parameters of the dermal wound without any dermatologic reactions.In conclusion,this innovative foam dressing had potential to be a good candidate for wound treatment.

Electroless copper plating on microcellular polyurethane foam

In order to obtain substrates with good conductive foam for high porosity foam metal materials used in the metal electrodes,the technique of electroless copper plating on the microcellular polyurethane foam with pore size of 0.3 mm was investigated.The main factors affecting the deposition rate such as the solution composition,temperature,pH value and adding ultrasonic were explored.The results show that the optimum process conditions are CuSO4 16 g/L,HCHO 5 mL/L,NaKC4H4O6 30 g/L,Na2EDTA 20 g/L,K4Fe(CN)6 25 mg/L,pH value of 12.5-13.0 and temperature of 40-50℃.Under these technical conditions, the process has excellent bath stability.Adding ultrasonic on the process can elevate the deposition rate of copper by 20%-30%.The foam metal material with a porosity of 92.2%and a three-dimensional network structure,was fabricated by electro-deposition after the electroless copper plating.

Synthesis of CO2 Copolymer Based Polyurethane Foams

CO2-copolymer based polyurethane foams were synthesized and characterized in this paper. The foams were found to have higher strength and lower heat of combustion than the conventional polyether polyurethane foams. They may find wide applications in many fields.

Fabrication and characterization of novel foaming polyurethane hollow fiber membrane

Foam-like materials had attracted great interest as promising absorbent. In this study, thermoplastic polyurethane(TPU) block sponge was synthesized. Polyester(PET) braid tubular reinforced polyurethane(PU) spongy hollow fiber membrane was prepared by a concentric circular spinning method. The method was woven from an outer coated water-blown PU separation layer and inner PET braid tubular. We have developed a simple and useful preparation technique for the PU spongy hollow fiber membrane. For the first time, the PU spongy hollow fiber membrane was prepared using a coating and controlled foaming technique. The influence of toluene isocyanate index on the physical properties, morphology, and structure of flexible PU sponge was discussed in terms of water contact angle(CA), pure water flux(PWF), Fourier Transform Infrared Analysis(FTIR),pressure-responsive property, and pull-out strength. The morphologies of the membranes were investigated by scanning electron microscopy. We have characterized the foams from an intuitive point of view and demonstrated that the dimensional morphology of the membrane was closely related to isocyanate index. The result showed that the surface cell size of the PU sponge hollow fiber membrane gradually decreased with an increase of the isocyanate index. Due to the elasticity of PU at room temperature, the pressure responsive characteristic of the membrane was prepared. When isocyanate index was 1.05, the interface bonding strength of PU spongy hollow fiber membranes reached as high as 0.37 MPa, porosity and PWF were 71.5% and 415.5 L·m^-2·h^-1,respectively.

Preparation and Properties of Electrospun Polyvinylidene Fluoride (PVDF)/Polyurethane (PU) Composite Nanofiber Membranes

Polyvinylidene fluoride(PVDF)/polyurethane(PU)composite nanofiber membranes were prepared by mixing PVDF and PU at different mass ratios.The microstructure and the crystal structure of the composite nanofiber membranes were analyzed by scanning electron microscopy(SEM),Fourier transform infrared(FTIR)spectroscopy and X-ray diffraction(XRD).The hydrophilicity,mechanical properties and piezoelectric properties were also tested.Results showed that when the mass ratio of PVDF to PU was 9∶1,the fiber membrane had the best microstructure,and the crystal form of PVDF changed fromαcrystal toβcrystal in the electrospinning.The addition of PU improved the hydrophilicity,mechanical properties,and piezoelectric signal of the fiber membrane.When the mass ratio of PVDF to PU was 9∶1,the tensile strength reached the peak value of(10.39±0.41)N,and the output voltage reached the maximum value of(1.98±0.12)V.

Effect of Cellular Structure on Mechanical Properties of Polyurethane Foam Curing Materials

Based on the mechanical properties and microstructure of polyurethane foam solidified material, a two-dimensional model of polyurethane foam solidified material was constructed. Polyurethane foam was obtained by fully and uniformly mixing the two components. The research was carried out through the combination of experimental test and finite element simulation. The experimental results show that when the pore density is constant, the size of the bubble hole is an important factor affecting the mechanical properties of the model. The smaller the size of the bubble hole, the less likely it is to produce stress concentration inside the model, and the stronger the resistance to material deformation. Under the random distribution, the lower the density of the polyurethane cured material, the higher the probability of damage between the adjacent bubbles, which is not conducive to the stability of the material. The density of the cured material should not be lower than 199 kg/m^3.

Broadband microwave absorption properties of polyurethane foam absorber optimized by sandwiched cross-shaped metamaterial

The effect of a sandwiched cross-shaped metamaterial absorber(CMMA) on microwave absorption properties of the double-layered polyurethane foam absorber(PUFA) is investigated. Combining with the sandwiched CMMA, the bandwidth of -10-dB reflection loss for PUFA is broadened from 7.4 GHz to 9.1 GHz, which is attributed to the overlap of two absorption peaks originating from CMMA and PUFA, respectively. The values of the two absorption peaks located at 10.15 GHz and 14.7 GHz are -38.44 dB and -40.91 dB, respectively. Additionally, distribution of surface current,electromagnetic field and power loss density are introduced to investigate the absorption mechanism of the CMMA. The electromagnetic field distribution of the double-layered PUFA and the three-layered hybrid absorber are comparatively analyzed to ascertain the influence of CMMA. The results show that the proposed hybrid absorber can be applied to the anti-electromagnetic interference and stealth technology.

Performance characterization of rigid polyurethane foam with refined alkali lignin and modified alkali lignin

The two kinds of rigid polyurethane(PU) foams were prepared with respectively adding the refined alkali lignin and alkali lignin modified by 3-chloro-1,2-epoxypropane to be instead of 15% of the polyether glycol in weight.The indexes of mechanical performance, apparent density, thermal stability and aging resistance were separately tested for the prepared PU foams.The results show that the mechanical property, thermal insulation and thermal stability for PU foam with modified alkali lignin are excellent among two kinds of PU foams and control samples.The additions of the refined alkali lignin and modified alkali lignin to PU foam have little effect on the natural aging or heat aging resistance except for decreasing hot alkali resistance apparently.Additionally, the thermal conductivity of modified alkali lignin PU foam is lowest among two kinds of PU foams and control samples.The alkali lignin PU foam modified by 3-chloro-1,2-epoxypropane could be applied in the heat preservation field.

Compression behavior and constitutive model establishment of fly ash cenosphere/polyurethane aluminum alloy syntactic foam

The aluminum matrix syntactic foam was fabricated by pressure infiltration technique,and the filling material is syntactic foam material with fly ash cenosphere as the main component and polyurethane foam as the binder.Split Hopkinson pressure bar(SHPB)dynamic compression and quasi-static tests were carried out to examine the compressive response of syntactic foam in this study.Then the dynamic constitutive model was established.Results show that the compressive stress-strain curve of syntactic aluminum foam is similar to that of other metallic foam materials:both kinds of aluminum matrix syntactic foams have strain rate effect,and the syntactic foam has higher compressive strength and energy absorption than the same density aluminum foams.However,due to the different sizes of cenospheres,the dynamic compression results of two kinds of syntactic foams are different,and the energy absorption effect of syntactic foam with small size under dynamic impact is the best.In the range of strain rate and density studied experimentally,the curves of constitutive model fit well with the curves of experimental data.