Recovery Stress in a Ni-Ti-Nb Shape Memory Alloy with Wide Transformation Hysteresis

The effect of deformation on recovery stress of Ni144.7Ti46.3Nb9 alloy has been studjed using tensile test at various temperatures and TEM observation. It ls shown that the recovery stress increases with jncreasing total strain ET and reaches a maximum value (max) as ET= 9% but the maximum recov erV strain of the alloy is only about 4.6%. This is different from that of Ti-Ni binary alloy in which is obtained usually at maximum recovery strain and the reason of the difference is dis Cussed. Deformation temperature Td has a little effect on recovery stress when Td is less than Ms However, recovery stress decreases sharply when Td is higher than M, and lowers approximately down to zero near Msσ

EFFECTS OF HEAT TREATMENT ON TENSILE PROPERTIES AND SHAPE MEMORY EFFECTS OF Ni-Ti-Nb ALLOY

ＥＦＦＥＣＴＳＯＦＨＥＡＴＴＲＥＡＴＭＥＮＴＯＮＴＥＮＳＩＬＥＰＲＯＰＥＲＴＩＥＳＡＮＤＳＨＡＰＥＭＥＭＯＲＹＥＦＦＥＣＴＳＯＦＮｉＴｉＮｂＡＬＬＯＹ①ＺｈｅｎｇＹｕｆｅｎｇ，ＣａｉＷｅｉ，ＬｕｏＹｉｃｈｕｎ，ＺｈａｏＬｉａｎｃｈｅｎｇＳｃｈｏｏ...

Role of Ag addition on microstructure,mechanical properties,corrosion behavior and biocompatibility of porous Ti-30 at%Ta shape memory alloys

In the present study,the thermal,mechanical,and biological properties of xAg/Ti-30Ta(x=0,0.41,0.82 and 2.48 at%)shape memory alloys(SMAs)were investigated.The study was conducted using optical and scanning electron microscopy(SEM),X-ray diffractometry(XRD),compression test,and shape memory testing.The xAg/Ti-Ta was made using a powder metallurgy technique and microwave-sintering process.The results revealed that the addition of Ag has a significant effect on the pore size and shape,whereas the smallest pore size of 11μm was found with the addition of 0.41 at%along with a relative density of 72%.The fracture stress and strain increased with the addition of Ag,reaching the minimum values around 0.41 at%Ag.Therefore,this composition showed the maximum stress and strain at fracture region.Moreover,0.82 Ag/Ti-Ta shows more excellent corrosion resistance and biocompatibility than other percentages,obtaining almost the same behaviour of the pure Ti and Ti-6Al-4V alloys,which can be recommended for their promising and potential response for biomaterial applications.

REVERSIBLE TRANSFORMATION BETWEEN MATRIX AND MARTENSITE IN Ni-Ti SHAPE MEMORY ALLOYS

The reversible transformation between matrix and martensite in Ni-Ti shape memory alloys has been dynamically observed under TEM.The orientation relation between martensite and austenite as well as the structural change near the transition temperature has been also studied with the help of HREM SADP.The results show that the orientation relation between martensite and austenite is[11]_A//[10]_M,[110]_A//[001]_M,(110)_A//(001)_M and the angle between(110)_A and(010)_M is about 6.5°.The crystal defects of martensite are found to be twin and stacking fault,and the twin plane as(100).

Relationship between phase composition and corrosion resistance of Ni-Ti-Nb based shape memory alloys

The stability and microstructure of Ni Ti Nb based shape memory alloys were investigated after alloyed with elements Zr, Cr and V. In artificial seawater (3.5%NaCl) and physiological solution (5%NaCl+0.1%H 2O 2), the results show that the alloying elements influence the corrosion behavior of Ni Ti Nb alloys. Generally, Zr improves the corrosion resistance of Ni Ti Nb alloy, Cr reduces its corrosion resistance and V does not change the property. In order to investigate the reason of the difference,the relation of the phase components and corrosion resistance of Ni Ti Nb based shape memory alloys were studied by element analysis and SEM.

Modeling of Ni_4Ti_3 precipitation during stress-free and stress-assisted aging of bi-crystalline NiTi shape memory alloys

The phase field method was applied to study the microstructure evolution of Ni4Ti3 precipitates during stress-free and stress-assisted aging of bi-crystalline NiTi shape memory alloys （SAMs） with two different initial Ni-contents of 51.5% and 52.5% （mole fraction）, respectively. The simulation results show that, during stress-free aging of the NiTi alloy with a low supersaturation of Ni （i.e., Ti-51.5%Ni）, the Ni4Ti3 precipitates exhibit a heterogeneous distribution with a high number density of particles at the grain boundary, leaving most of the grain interiors free of precipitates; while for the NiTi alloy with a high supersaturation of Ni （i.e., Ti-52.5%Ni）, the Ni4Ti3 precipitates show a homogeneous distribution across the entire simulation system. The stress-assisted aging can give rise to homogeneous distribution of the precipitates, regardless of the initial Ni-content; however, the distribution of variant type within the two grains is heterogeneous.

COMPOSITION TRIANGLE DIAGRAMS OF Ni-Mn-Ga MAGNETIC SHAPE MEMORY ALLOYS

A statistical work has been done to collect the composition ranges of Ni-Mn-Ga alloys exhibiting different structures and martensite start temperature （M,）, large magnetostrain or the co-existence of magnetic and structural transitions. The alloys with five-layered （5M）, seven-layered （7M） modulated and non-modulated （T） martensitic structures were mapped in the graph. An empirical formula has been presented to reflect the effect of elements nickel （Ni ）, manganese （ Mn ） and gallium （Ga）, on the martensite start temperature （M3）. The martensitic structure is sensitive to the composition and the martensitic transformation temperature is most drastically affected by the Ni content. The alloys with large magnetostrain or co-existence effect of the magnetic and structural transitions were also listed in a limited area.

Influences of 2.5wt%Mn addition on the microstructure and mechanical properties of Cu-Al-Ni shape memory alloys

The influences of 2.5wt%Mn addition on the microstructure and mechanical properties of the Cu-11.9wt%Al-3.8wt%Ni shape memory alloy（SMA） were studied by means of scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,and differential scanning calorimeter（DSC）.The experimental results show that Mn addition influences considerably the austenite-martensite transformation temperatures and the kind of martensite in the Cu-Al-Ni alloy.The martensitic transformation changes from a mixedβ1→β＇1＋γ＇1 transformation to a singleβ1→β＇1 martensite transformation together with a decrease in transformation temperatures.In addition,the observations reveal that the grain size of the Cu-Al-Ni alloy can be controlled with the addition of 2.5wt%Mn and thus its mechanical properties can be enhanced.The Cu-Al-Ni-Mn alloy exhibits better mechanical properties with the high ultimate compression strength and ductility of 952 MPa and 15%,respectively.These improvements are attributed to a decrease in grain size.However,the hardness decreases from Hv 230 to Hv 140 with the Mn addition.

Martensite Aging Effect and Thermal Cyclic Characteristics in Ti-Pd and Ti-Pd-Ni High Temperature Shape Memory Alloys

The effect of thermal cycling and aging in martensitic state in Ti-Pd-Ni alloys were investigated by DSC and TEM observations. It is shown that the thermal cycling causes the decreases in M, and Af temperatures in Ti50Pd50-xNix (x=10, 20, 30) alloys, but no obvious thermal cycling effect was observed in Ti50Pd50Pd40Ni10 alloys and the aging effect shows a curious feature, i.e., the Af temperature does not saturate even after relatively long time aging, which is considered to be due to the occurrence of recovery recrystallization during aging.

Transformation behavior and shape memory effect of Ti_(50-x)Ni_(48)Fe_2Nb_x alloys by aging treatment

The influence of aging treatment on transformation behavior and shape memory of the Ti 50_x Ni_(48) Fe_2 Nb_x(x=0,0.6,0.8,1.0,and 1.2) alloys was investigated using differential scanning calorimeter(DSC),mechanical drawing machine,and microhardness tester in this paper.It is indicated that the aging treatment has a significant effect on the phase transformation temperatures(M_s,M_f,M_p,A_s,A_f,and A_p) and microhardness of the samples.The phase transformation temperatures are found to decrease initially with the increasing aging temperature from 300 to 500 ℃ and increase with further increase of the aging temperature.The aging treatment at intermediate temperature between 400 and 500 ℃ results in an improved shape memory effect.In addition,the highest microhardness value is also obtained.

Effect of Pre-strain on the Transformation and Recovery Behaviours of a Ti_(44)Ni_(47)Nb_9 Shape Memory Alloy

The recovery strain, stress and transformation temperature of different pre-strained specimens of Ti44Ni47Nb9 were investigated by tensile test and electrical resistance measurement. The results indicated that pre-strain increases the reverse martensitic transformation temperature (A ' (s)) and hysteresis (A(s) - M-s). The recovery strain and stress are higher if the specimens are pre-strained between M-s and A(s) temperature than outside this temperature range. There exists an optimal pre-strain value, about 10%, at which the specimen exhibits maximum recovery strain and stress.

Factors Affecting Transformation Temperatures in Fe-Mn-Si-Cr-Ni Shape Memory Alloy

The effects of prestrain and annealing temperature on phase transformation temperatures in Fel4Mn5Si8Cr4Ni shape memory alloy have been studied. The results showed that when the annealing temperature was 673 K, both the At and the Ms temperatures increased appreciably as the prestrain increased, the As temperature increased slightly with increasing prestrain; the resistivity difference at 303 K between the heating and cooling curve also increased with increasing prestrain, which agreed with the recovery strain. The shape memory effect in Fe-Mn-Si-Cr-Ni shape memory alloy is caused by the stress-induced γ→ε martensite transformation and its reverse transformation. When the prestrain was 10%, the Ms temperature decreased remarkably as the annealing temperature increased.

Two-way Shape Memory Effect in a Ti-Ni-Nb Shape Memory Alloy with Wide Hysteresis

A two-way shape memory effect (TWSM E) in the Ti46.3Ni44.7Nb9 alloy has been systematically investigated by means of bending test and transmission electron microscopy (TEM ) observations. Based on the analysis of the microstructure after training. the mechanism of TWSME in the Ti46.3 Ni44.7Nb9 alloy has been discussed.

Shape Memory Effect of As-aged Fe-14Mn-5Si-8Cr-4Ni-0.2C Alloy

The effects of aging temperature on shape memory effect, mechanical properties and microstruc-ture of Fe-14Mn-5Si-8Cr-4Ni-0.2C shape memory alloy have been studied. The results showed that the second phase particles rich in chromium, manganese and silicon precipitate during aging, and thereby increase the hardness and strength of the alloy. The shape recovery ratio can be remarkably improved by aging and a maximum value can be obtained at 1223 K, which is 68% higher than that of the specimen in solid solution state. When the aging temperature is below 1223 K, the amount of second phase particles increases as the aging temperature increases. The size of austenite grain increases with increasing aging temperature. When the temperature is over 1223 K, the second phase particles can not precipitate. The lack of second phase particles and the increase of grain size make the hardness and shape recovery ratio drastically decrease, when the temperature is over 1223 K.

Electrochemical behavior of Cu-Zn-Al shape memory alloy after surface modification by electroless plated Ni-P

The electrochemical behavior of Cu-Zn-Al shape memory alloy (SMA) with andwithout electroless plated Ni-P was investigated by electrochemical methods, in artificial Tyrode'ssolution. The results showed that Cu-Zn-Al SMA engendered dezincification corrosion in Tyrode'ssolution. The anodic active current densities as well as electrochemical dissolution sensitivity ofthe electroless plated Ni-P Cu-Zn-Al SMA increased with NaCl concentration rising, pH of solutiondecreasing and environmental temperature uprising. X-ray diffraction analysis indicated that aftersurface modification by electroless plated Ni-P, an amorphous plated film formed on the surface ofCu-Zn-Al SMA. This film can effectively isolate matrix metal from corrosion media and significantlyimprove the electrochemical property of Cu-Zn-Al SMA in artificial Tyrode's solution.

Temperature Dependent Work-hardening Behaviour in an Fe-Mn-Si-Cr-Ni Shape Memory Alloy

The work-hardening behaviour in an Fe-Mn-Si-Cr-Ni alloy has been investigated using tensile test at different temperatures and TEM observation. It was found that besides the intersection of εmartensite, the intersections of ε martensite with stacking fault and the cross-slip of dislocation which is difficult to occur in the alloy with low stacking fault energy are also important factors to the temperature dependent work-hardening behaviour.

Microstructure and Mechanical Properties of Cross-rolled Ti_(50)Ni_(47)Fe_3 Shape Memory Alloy

The microstructures, the phase transformation characteristics, and the mechanical properties of the Ti50Ni47Fe3 alloy in as-forged and as-cross-rolled states were investigated. It is found that, after cross-rolling, the phase transformation temperature （Ms） of the alloy decreases drastically and the grains get refined. Moreover, its yield strength and fracture strength after cross-rolling hit 540 MPa and 687 MPa respectively, up by about 200 MPa over those in as-forged state.

ORDERING OF VACANCIES IN RAPIDLYQUENCHED TiNi SHAPE MEMORY ALLOY

The modification of the electron diffraction pattern(EDP) of B2 in an as rapidly quenched then short time aged Ti Ni shape memory alloy(SMA) has been studied systematically using TEM. It was found that the diffusion scattering rings in EDP of an as rapidly quenched Ti-Ni SMA is associated with short range order (SRO) of vancancies in parent B2. After aging at 450℃ for 5 min the diffusion scattering rings are replaced by 1/2 {001} and 1 / 4 {012} extra reflections. It indicates that the SRO of vacancies has transformed into long range order (LRO) of vacancies,moreover,the LRO of vacancies exists in microdomains.

Thermodynamic Analysis on Relation Between T_0 and σ_M in a Ti_(44)Ni_(47)Nb_9 Shape Memory Alloy

The effect of heat treatment on martensitic transformation behavior has been investigated in Ti44Ni47Nb9 alloy. The relation between transformation temperatures and critical stress of stress induced martensitic transformation is interpreted in terms of thermodynamic theory. It is shown that the decrease in transformation temperature in specimens of slow cooling rate or low temperature aging after solution heat treatment results from the changes of Ni/Ti ratio in the matrix. The increase of critical stress of stress induced martensitic transformation is a consequence of the decrease of transformation temperatures.

Experimental investigation of the cyclic degradation of the one-way shape memory effect of NiTi alloys

Based on stress-and strain-controlled cyclic tension-unloading-heat-cooling tests,cyclic degradation of the one-way shape memory effect(OWSME)of NiTi shape memory alloys(SMAs)was investigated.It was seen,in thermo-mechanical coupled cyclic tests,that residual strain after each cycle accumulated,but the martensite reorientation stress and dissipation energy-per-cycle decreased as the number of cycles increased.Meanwhile,the cyclic degradation of OWSME was aggravated by increasing the stress/strain amplitude.In addition,the stress-strain response of NiTi SMAs was further investigated by performing simultaneous thermo-mechanical coupled cyclic tests with various phase-angle differences between the mechanical and thermal cyclic loadings.It can be concluded that such cyclic response depends significantly on prescribed phase-angle differences.Obtained experimental results are helpful for both the development of constitutive models and engineering applications of NiTi SMAs.