期刊文献+
共找到4,015篇文章
< 1 2 201 >
每页显示 20 50 100
Analysis of the Application of Static Load Test in Bridge Bearing Capacity Testing
1
作者 Wei Fu Bo Liu 《Journal of Architectural Research and Development》 2024年第3期36-41,共6页
This article uses real engineering projects as examples to analyze how static load test technology is applied in testing the bridge-bearing capacity.The analysis covers aspects such as testing section layout,test load... This article uses real engineering projects as examples to analyze how static load test technology is applied in testing the bridge-bearing capacity.The analysis covers aspects such as testing section layout,test load and efficiency coefficient,loading plan,evaluation optimization,test result modification,and result evaluation.The aim is to support the accurate detection and evaluation of bridge-bearing capacity. 展开更多
关键词 Bridge engineering bearing capacity Static load test loading plan Test evaluation
下载PDF
Determination of the load bearing capacity of pre-stressed expandable props for ground support in underground mines 被引量:1
2
作者 Kunmeng Li Kaiyuan Jiang +3 位作者 Yuanhui Li Xin Wang Kai Liu Shuai Xu 《International Journal of Mining Science and Technology》 SCIE EI CAS CSCD 2023年第8期977-990,共14页
This paper aims to determine the load bearing capacity of pre-stressed expandable props with different geometries and load eccentricities for flexible support in underground mining or excavation.It is deduced that the... This paper aims to determine the load bearing capacity of pre-stressed expandable props with different geometries and load eccentricities for flexible support in underground mining or excavation.It is deduced that the expandable device could have much higher strength(>89 MPa)by laboratory tests,and the load bearing capacity of the expandable prop may depend on the stability of the supporting steel pipe structure.A good agreement was found between the laboratory test and numerical results in terms of the load bearing capacity and the final macro-bending failure pattern for expandable props with heights of 1.5 and 2.7 m,and the theoretical calculation for the strength of traditional steel structures is not directly suitable for the expandable props.Moreover,additional numerical simulations were performed for the expandable props with different normalized slenderness ratiosλ_(n)and loading eccentric distances e.The variation of stability coefficient of the expandable prop is in line with the Perry-Robertson equation and its correlation coefficients are fitted as a of 0.979 and b of 0.314.For estimating the load bearing capacity of the expandable props,the strength equation for traditional steel structures is improved by introducing a bending magnification factor and by modifying the normalized slenderness ratio to a converted slenderness ratio.Based on the underground field monitoring for the strength of expandable props with different heights,the empirical eccentric distances were back calculated,and a safety factor is introduced to obtain the designed strength of the expandable prop.In addition,a four-step design procedure is proposed for the expandable prop. 展开更多
关键词 Pillar stability load bearing capacity Expandable prop Slenderness ratio Eccentric distance
下载PDF
Estimation of Undrained Bearing Capacity for Offshore Soft Foundations with Cyclic Load 被引量:18
3
作者 Wang, JH Liu, YF +1 位作者 Xing, Y Di, HM 《China Ocean Engineering》 SCIE EI 1998年第2期213-222,共10页
The degradation strength of soils under cyclic loading is studied and a method for determining the cyclic degradation strength with cyclic triaxial tests is given in the paper. Furthermore, a dum my static method for ... The degradation strength of soils under cyclic loading is studied and a method for determining the cyclic degradation strength with cyclic triaxial tests is given in the paper. Furthermore, a dum my static method for estimating the undrained bearing capacity for offshore soft foundation under wave loads is developed. It can consider the effect of the difference of cyclic stress for different parts of the foundation on both the degradation strength of the foundation soil and the bearing capacity so that the estimated result can better reflect the real condition of foundation under cyclic loading. The method can be applied to plane and space problem. 展开更多
关键词 offshore engineering soft foundation soil dynamics bearing capacity cyclic load
下载PDF
H-M Bearing Capacity of A Modified Suction Caisson Determined by Using Load-/Displacement-Controlled Methods 被引量:11
4
作者 张雨坤 高玉峰 +1 位作者 李大勇 Ali H.Mahfouz 《China Ocean Engineering》 SCIE EI CSCD 2016年第6期926-941,共16页
This paper presents a series of monotonically combined lateral loading tests to investigate the bearing capacity of the MSCs (modified suction caissons) in the saturated marine fine sand. The lateral loads were appl... This paper presents a series of monotonically combined lateral loading tests to investigate the bearing capacity of the MSCs (modified suction caissons) in the saturated marine fine sand. The lateral loads were applied under load- and displacement-controlled methods at the loading eccentricity ratios of 1.5, 2.0 and 2.5. Results show that, in the displacement-controlled test, the deflection-softening behavior of load-deflection curves for MSCs was observed, and the softening degree of the load-deflection response increased with the increasing external skirt length or the decreasing loading eccentricity. It was also found that the rotation center of the MSC at failure determined by the load-controlled method is slightly lower than that by the displacement-controlled method. The calculated MSC capacity based on the rotation center position in serviceability limit state is relatively conservative, compared with the calculated capacity based on the rotation center position in the ultimate limit state. In the limit state, the passive earth pressures opposite the loading direction under load- and displacement-controlled methods decrease by 46% and 74% corresponding to peak values, respectively; however, the passive earth pressures in the loading direction at failure only decrease by approximately 3% and 7%, compared with their peak values. 展开更多
关键词 MSC (modified suction caisson) saturated marine fine sand model tests load- and displacement-controlled loading laterally combined bearing capacity earth pressure
下载PDF
Load Bearing Capacity and Safety Analysis for Strain-hardening Austenitic Stainless Steel Pressure Vessels 被引量:7
5
作者 CHEN Gang DENG Yangchun 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2011年第2期179-186,共8页
By increasing the yield strengths of austenitic stainless steels for pressure vessels with strain hardening techniques,the elastic load bearing capacity of austenitic stainless steel pressure vessels can be significan... By increasing the yield strengths of austenitic stainless steels for pressure vessels with strain hardening techniques,the elastic load bearing capacity of austenitic stainless steel pressure vessels can be significantly improved.Two kinds of strain hardening methods are often used for austenitic stainless steel pressure vessels:Avesta model for ambient temperature applications and Ardeform model for cryogenic temperature applications.Both methods are obtained from conventional design rules based on the linear elastic theory,and only consider the hardening effect from materials.Consequently this limits the applications of strain hardening techniques for austenitic stainless steel pressure vessels because of safety concerns.This paper investigates the effect of strain hardening on the load bearing capacity of austenitic stainless steel pressure vessels under large deformation,based on the elastic-plastic theory.Firstly,to understand the effect of strain hardening on material behavior,the plastic instability loads of a round tensile bar specimen are derived under two different loading paths and validated by experiments.Secondly,to investigate the effect of strain hardening on pressure vessels strength, the plastic instability pressure under strain hardening is derived and further validated by finite element simulations.Further,the safety margin of pressure vessels after strain hardening is analyzed by comparing the safety factor values calculated from bursting tests,finite element analyses,and standards.The researching results show that the load bearing capacity of pressure vessels at ambient temperature is independent of the loading history when the effects of both material strain hardening and structural deformation are considered.Finite element simulations and bursting tests results show that the minimum safety factor of austenitic stainless steel pressure vessels with 5% strain hardening is close to the recommended value for common pressure vessels specified in the European pressure vessel standard.The proposed study also shows that in the strain hardening design of austenitic stainless steel pressure vessels,the calculation for plastic instability pressure could use theoretical formula or finite element analyses based on geometrical dimensions and material property parameters before strain hardening,but a 5%strain should be employed as a design limit.The proposed research can be used for the strain hardening design of austenitic stainless steel pressure vessels safely. 展开更多
关键词 pressure vessel austenitic stainless steel strain hardening load bearing capacity safety margin
下载PDF
Influence of Particles on the Loading Capacity and the Temperature Rise of Water Film in Ultra-high Speed Hybrid Bearing 被引量:3
6
作者 ZHU Aibin LI Pei +2 位作者 ZHANG Yefan CHEN Wei YUAN Xiaoyang 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2015年第3期541-548,共8页
Ultra-high speed machining technology enables high efficiency, high precision and high integrity of machined surface. Previous researches of hybrid bearing rarely consider influences of solid particles in lubricant an... Ultra-high speed machining technology enables high efficiency, high precision and high integrity of machined surface. Previous researches of hybrid bearing rarely consider influences of solid particles in lubricant and ultra-high speed of hybrid bearing, which cannot be ignored under the high speed and micro-space conditions of ultra-high speed water-lubricated hybrid bearing. Considering the impact of solid particles in lubricant, turbulence and temperature viscosity effects of lubricant, the influences of particles on pressure distribution, loading capacity and the temperature rise of the lubricant film with four-step-cavity ultra-high speed water-lubricated hybrid bearing are presented in the paper. The results show that loading capacity of the hybrid bearing can be affected by changing the viscosity of the lubricant, and large particles can improve the bearing loading capacity higher. The impact of water film temperature rise produced by solid particles in lubricant is related with particle diameter and minimum film thickness. Compared with the soft particles, hard particles cause the more increasing of water film temperature rise and loading capacity. When the speed of hybrid bearing increases, the impact of solid particles on hybrid bearing becomes increasingly apparent, especially for ultra-high speed water-lubricated hybrid bearing. This research presents influences of solid particles on the loading capacity and the temperature rise of water film in ultra-high speed hybrid bearings, the research conclusions provide a new method to evaluate the influence of solid particles in lubricant of ultra-high speed water-lubricated hybrid bearing, which is important to performance calculation of ultra-high speed hybrid bearings, design of filtration system, and safe operation of ultra-high speed hybrid bearings. 展开更多
关键词 hybrid bearing liquid-solid flow solid particles loading capacity temperature rise
下载PDF
Vertical bearing capacity of pile based on load transfer model 被引量:7
7
作者 赵明华 杨明辉 邹新军 《Journal of Central South University of Technology》 EI 2005年第4期488-493,共6页
The load transfer analytical method is applied to study the bearing mechanism of piles with vertical load in this paper. According to the different hardening rules of soil or rock around the pile shaft, such as work-s... The load transfer analytical method is applied to study the bearing mechanism of piles with vertical load in this paper. According to the different hardening rules of soil or rock around the pile shaft, such as work-softening, ideal elasto-plastic and work-hardening, a universal tri-linear load transfer model is suggested for the development of side and tip resistance by various types of soil (rock) with the consideration of sediment at the bottom of the pile. Based on the model, a formula is derived for the relationship between the settlement and load on the pile top to determine the vertical bearing capacity, taking into account such factors as the characteristics of the stratum, the side resistance along the shaft, and tip resistance under the pile tip. A close agreement of the calculated results with the measured data from a field test pile lends confidence to the future application of the present approach in engineering practice. 展开更多
关键词 pile foundation load transfer model top settlement vertical bearing capacity
下载PDF
Undrained Bearing Capacity of Spudcan Under Combined Loading 被引量:2
8
作者 王立忠 舒恒 +1 位作者 李玲玲 国振 《China Ocean Engineering》 SCIE EI 2011年第1期15-30,共16页
The bearing capacities of spudcan foundation under pure vertical (/1), horizontal (H), moment (M) loading and the combined loading are studied based on a series of three-dimensional finite element analysis. The ... The bearing capacities of spudcan foundation under pure vertical (/1), horizontal (H), moment (M) loading and the combined loading are studied based on a series of three-dimensional finite element analysis. The effects of embedment ratio and soil non-homogeneity on the bearing capacity are investigated in detail. The capacities of spudcan under different pure loading are expressed in non-dimensional bearing capacity factors, which are compared with published results. Ultimate limit states under combined loading are presented by failure envelopes, which are expressed in terms of dimensionless and normalized form in three-dimensional load space. The comparison between the presented failure envelopes and available published numerical results reveals that the size and shape of failure envelopes are dependent on the embedment ratio and the non-homogeneity of the soil. 展开更多
关键词 soft clay SPUDCAN bearing capacity combined loading finite element
下载PDF
Determination of ultimate bearing capacity of uplift piles using intact and non-intact load−displacement curve 被引量:5
9
作者 WANG Qin-ke MAJian-lin +2 位作者 JI Yu-kun ZHANG Jian CHEN Wen-long 《Journal of Central South University》 SCIE EI CAS CSCD 2022年第2期470-485,共16页
Based on the field destructive test of six rock-socketed piles with shallow overburden,three prediction models are used to quantitatively analyze and predict the intact load−displacement curve.The predicted values of ... Based on the field destructive test of six rock-socketed piles with shallow overburden,three prediction models are used to quantitatively analyze and predict the intact load−displacement curve.The predicted values of ultimate uplift capacity were further determined by four methods(displacement controlling method(DCM),reduction coefficient method(RCM),maximum curvature method(MCM),and critical stiffness method(CSM))and compared with the measured value.Through the analysis of the relationship between the change rate of pullout stiffness and displacement,a method used to determine the ultimate uplift capacity via non-intact load−displacement curve was proposed.The results show that the predicted value determined by DCM is more conservative,while the predicted value determined by MCM is larger than the measured value.This suggests that RCM and CSM in engineering applications can be preferentially applied.Moreover,the development law of the change rate of pullout stiffness with displacement agrees well with the attenuation form of power function.The theoretical predicted results of ultimate uplift capacity based on the change rate of pullout stiffness will not be affected by the integrity of the curve.The method is simple and applicable for the piles that are not loaded to failure state,and thus provides new insights into ultimate uplift capacity determination of test piles. 展开更多
关键词 load−displacement curve prediction model determination method of bearing capacity change rate of pullout stiffness
下载PDF
Contact Force Distribution and Static Load-carrying Capacity of Large Size Double Row Four-point Contact Ball Bearing 被引量:7
10
作者 Yan-shuang WANG Qian-qian YUAN 《Defence Technology(防务技术)》 SCIE EI CAS 2013年第4期229-236,共8页
Clearance not only affects the startup torque,rotation precision and stiffness of bearing,but also affects the load distribution,load-carrying capacity and life of bearing.A computational model in which the clearance ... Clearance not only affects the startup torque,rotation precision and stiffness of bearing,but also affects the load distribution,load-carrying capacity and life of bearing.A computational model in which the clearance of bearing is first included is presented for determining the contact force distribution and static load-carrying capacity of a double row four-point contact ball bearing which is subjected to the combined radial,axial and overturning moment loadings.The relation between the negative axial clearance and the contact force distribution is analyzed.The static load-carrying capacity curves are established,and the effects of the changes in negative axial clearance,curvature radius coefficient of raceway groove and initial contact angle on the static load-carrying capacity are analyzed.The results show that,with the increase in the absolute value of negative clearance,the maximum contact load decreases first and then increases.The clearance values in the range of 0.2 mme0 mm have little effect on the static load-carrying capacity of bearing.With the increase in the curvature radius coefficient of raceway groove and the decrease in the initial contact angle,the static load capacity of bearing decreases. 展开更多
关键词 四点接触球轴承 承载能力 接触力 静态 双排 大尺寸 轴向游隙 轴向间隙
下载PDF
Numerical and experimental analyses for bearing capacity of rigid strip footing subjected to eccentric load 被引量:1
11
作者 卢谅 王宗建 K.ARAI 《Journal of Central South University》 SCIE EI CAS 2014年第10期3983-3992,共10页
A footing may get an eccentric load caused by earthquake or wind, thus the bearing capacity of footing subjected to eccentric load become a fundamental geotechnical problem. The conventional limit equilibrium method u... A footing may get an eccentric load caused by earthquake or wind, thus the bearing capacity of footing subjected to eccentric load become a fundamental geotechnical problem. The conventional limit equilibrium method used for this problem usually evaluates the material properties only by its final strength. But the classical finite element method(FEM) does not necessarily provide a clear collapse mechanism associated with the yield condition of elements. To overcome these defects, a numerical procedure is proposed to create an explicit collapse mode combining a modified smeared shear band approach with a modified initial stress method. To understand the practical performance of sand foundation and verify the performance of the proposed procedure applied to the practical problems, the computing results were compared with the laboratory model tests results and some conventional solutions. Furthermore, because the proposed numerical procedure employs a simple elasto-plastic model which requires a small number of soil parameters, it may be applied directly to practical design works. 展开更多
关键词 bearing capacity eccentric load slip surface shear band finite element method model test
下载PDF
ULTIMATE LOAD-BEARING CAPACITY OF CYLINDER DERIVED FROM AUTOFRETTAGE UNDER IDEAL CONDITION 被引量:14
12
作者 ZHU Ruilin 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2008年第5期80-87,共8页
According to the basic theory on autofrettage and according to the 4th strength theory, several parameters and their relations are studied under ideal condition, including σej/σy, the equivalent stress of total stre... According to the basic theory on autofrettage and according to the 4th strength theory, several parameters and their relations are studied under ideal condition, including σej/σy, the equivalent stress of total stresses at elastoplastic juncture; σei/σy, the equivalent stress of total stresses at inside surface; σej'/σy, the equivalent stress of residual stresses at elastoplastic juncture; σei'/σy, the equivalent stress of residual stresses at inside surface; and p/σy, load-bearing capacity of an autofrettaged cylinder. By theoretical study on relations between the parameters, noticeable results and laws are achieved: to satisfy |σei'|=σy. the relation between kj and k is, k^2lnkj^2-k^2-kj^2+2=0, when k→∞, kj = √e = 1.648 72, as based on the 3rd strength theory, where k is the outside/inside radius ratio of a cylinder, kj is the ratio of elastoplastic juncture radius to inside radius of a cylinder; If the plastic region covers the whole wall of a cylinder, for compressive yield not to occur after removing autofrettage pressure, the ultimate k is k=-2.218 46 as based on the 3rd strength theory; With k=2.218 46, a cylinder's ultimate load-bearing capacity equals its entire yield pressure, or p/σy=21nk/√3; The maximum and optimum load-bearing capacity of an autofrettaged cylinder is just 2 times the loading which an unautofrettaged cylinder can bear elastically, or p/σy=2(k^2-1)/√3 k^2, and the limit of the load-bearing capacity of an autofrettaged cylinder is also just 2 times that of an unautofrettaged cylinder. The conclusions are the same as based on the 3rd strength theory, but some equations are different from each other. 展开更多
关键词 Cylinder Autofrettage load-bearing capacity
下载PDF
Effect of Optimum Plastic Depth on Stresses and Load-bearing Capacity of Autofrettaged Cylinder 被引量:2
13
作者 ZHU Ruilin ZHU Guolin 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2013年第2期365-370,共6页
Autofrettage is an effective measure to even distribution of stresses and raise load-bearing capacity for (ultra-)high pressure apparatus. Currently, the research on autofrettage has focused mostly on specific engin... Autofrettage is an effective measure to even distribution of stresses and raise load-bearing capacity for (ultra-)high pressure apparatus. Currently, the research on autofrettage has focused mostly on specific engineering problems, while general theoretical study is rarely done. To discover the general law contained in autofrettage theory, by the aid of the authors’ previous work and according to the third strength theory, theoretical problems about autofrettage are studied including residual stresses and their equivalent stress, total stresses and their equivalent stress, etc. Because of the equation of optimum depth of plastic zone which is presented in the authors’ previous work, the equations for the residual stresses and their equivalent stress as well as the total stress and their equivalent stress are simplified greatly. Thus the law of distribution of the residual stresses and their equivalent stress as well as the total stress and their equivalent stress and the varying tendency of these stresses are discovered. The relation among various parameters are revealed. The safe and optimum load-bearing conditions for cylinders are obtained. According to the results obtained by theoretical analysis, it is shown that if the two parameters, namely ratio of outside to inside radius, k, and depth of plastic zone, kj, meet the equation of optimum depth of plastic zone, when the pressure contained in an autofrettaged cylinder is lower than two times the initial yield pressure of the unautofrettaged cylinder, the equivalent residual stress and the equivalent total stress at the inside surface as well as the elastic-plastic juncture of a cylinder are lower than yield strength. When an autofrettaged cylinder is subjected to just two times the initial yield pressure of the unautofrettaged cylinder, the equivalent total stress within the whole plastic zone is just identically equal to the yield strength, or it is a constant. The proposed research theoretically depicts the stress state of ultra-)high pressure autofrettaged cylinder more accurately and more reasonably and provides the reference for design of (ultra-)high pressure apparatus. 展开更多
关键词 thick-wall cylinder AUTOFRETTAGE residual stress load-bearing capacity
下载PDF
Ultimate Bearing Capacity of Hollow Spherical Joints Welded with Circular Pipes under Eccentric Loads
14
作者 韩庆华 周全智 +1 位作者 陈越 于宝林 《Transactions of Tianjin University》 EI CAS 2007年第1期28-34,共7页
The hollow spherical joints welded with circular pipes applied to the National Swimming Center of China are subjected to large bending moments, but the influence of bending moments is not considered in the design equa... The hollow spherical joints welded with circular pipes applied to the National Swimming Center of China are subjected to large bending moments, but the influence of bending moments is not considered in the design equations in Technical Specification for Latticed Shells. Based on the von Mises yield criterion, multilinear isotropic hardening rule and associated flow rule, the elasto-plastic finite element model is put forward to analyze the behavior of the joints, and a calculation method for the joints under bending moments or eccentric loads is proposed. It is shown by the analytical results of joint that the stiffening rib can improve the ultimate bearing capacity by 10% for joints under axial tensile load, by 40% for joints under axial compressive load, and by 50% for joints under bending moment. The unified calculation equations for joints with or without stiffening rib are put forward, which can be applied to calculating the ultimate bearing capacity of the hollow spherical joints with circular pipes under eccentric loads. 展开更多
关键词 hollow spherical joints welded with circular pipes bearing capacity finite element method elastoplasticity eccentric load influence of stiffening rib
下载PDF
Discussion on bearing capacity of soft rock ground based on in-situ load test
15
作者 Gao Wenhua Zhu Jianqun Huang Ziyong Liu Dong 《Engineering Sciences》 EI 2010年第4期37-41,共5页
The suitability of five methods was discussed here,taking the typical results from in-situ load test of Renshou Mansion and Caifu Plaza in Yueyang City for example.It shows that bearing capacity can be obtained by the... The suitability of five methods was discussed here,taking the typical results from in-situ load test of Renshou Mansion and Caifu Plaza in Yueyang City for example.It shows that bearing capacity can be obtained by the proportion load and limit load from p-s curve with the first and the second point of contraflexure easily.It is recommended that the accurate value of bearing capacity can be obtained by hyperbola fitting method and minimum curvature radius method theoretically.The rebound method is clear in principle,in which the elastoplasticity characteristic is thought about.Out of consideration for the unsteadiness and unobviousness of bearing capacity from relative settlement method,it can be only adopted as reference.So bearing capacity of soft rock ground should be determined by weathering condition of soft rock and curve type. 展开更多
关键词 rock mechanics soft rock bearing capacity of ground in-situ load test of rock ground characteristic curve
下载PDF
Load-Bearing Capacity of the Footing Resting on a Reinforced Fly Ash Slope
16
作者 Kulbir Singh Gill Anil Kumar Choudhary +1 位作者 Jagada Nand Jha Sanjay Kumar Shukla 《Journal of Civil Engineering and Architecture》 2012年第5期627-632,共6页
In several parts of the world, disposal of waste materials such as fly ash is a great problem. Application of waste materials as structural fills in foundations is one of the best solutions to disposal problems, becau... In several parts of the world, disposal of waste materials such as fly ash is a great problem. Application of waste materials as structural fills in foundations is one of the best solutions to disposal problems, because wastes can be used in large volumes in such applications. There may be difficulty due to poor load-bearing capacity of fly ash, especially when footing rests on the top of the fly ash fill slope. Inclusion of polymeric reinforcements as horizontal sheets within the fill may be one of the most viable solutions to improving the load-bearing capacity of reinforced fly ash slope, and it is particularly important for the situations where foundations need to be located either on the top of a slope or on slope itself. The present work is aimed at investigating the efficacy of a single layer of reinforcement in improving the lo, ad-bearing capacity when it gets incorporated within the body of a model fly ash embankment slope. An increase in load bearing capacity due to the incorporation of reinforcement in the model slope was found by conducting laboratory tests. Experimental results were compared by numerical values obtained using software GEO5 and PLAXIS. 展开更多
关键词 Reinforced fly ash slope polymeric reinforcement load bearing capacity numerical analysis.
下载PDF
The Plate Load Test in the Application of Dynamic Compaction Test of Subgrade Bearing Capacity
17
作者 Xichang Zhang Yuehong Su Zhi Zhang 《土木工程与技术(中英文版)》 2013年第2期34-39,共6页
关键词 土木工程 建筑工程 建筑设计 建筑材料
下载PDF
Finite element analysis of effect of soil displacement on bearing capacity of single friction pile 被引量:3
18
作者 王丽 郑刚 欧若楠 《Journal of Central South University》 SCIE EI CAS 2014年第5期2051-2058,共8页
Effect of soil displacement on friction single pile in the cases of tunneling,surcharge load and uniform soil movement was discussed in details with finite element method.Lateral displacement of the pile caused by soi... Effect of soil displacement on friction single pile in the cases of tunneling,surcharge load and uniform soil movement was discussed in details with finite element method.Lateral displacement of the pile caused by soil displacement reached about 90% of the total displacement,which means that P-Δ effect of axial load can be neglected.The maximum moment of pile decreased from 159 kN·m to 133 kN·m in the case of surcharge load when the axial load increased from 0 to the ultimate load.When deformation of pile caused by soil displacement is large,axial load applied on pile-head plays the role of reducing the maximum bending moment in concrete pile to some extent.When pile is on one side of the tunnel,soil displacements around the pile are all alike,which means that the soil pressures around the pile do not decrease during tunneling.Therefore,Q-s curve of the pile affected by tunneling is very close to that of pile in static loading test.Bearing capacities of piles influenced by surcharge load and uniform soil movement are 2480 kN and 2630 kN,respectively,which are a little greater than that of the pile in static loading test(2400 kN).Soil pressures along pile increase due to surcharge load and uniform soil movement,and so do the shaft resistances along pile,as a result,when rebars in concrete piles are enough,bearing capacity of pile affected by soil displacement increases compared with that of pile in static loading test. 展开更多
关键词 TUNNELING surcharge load uniform soil movement friction pile bearing capacity
下载PDF
Influence of cyclic loading on the fracture toughness and load bearing capacities of all-ceramic crowns 被引量:2
19
作者 Rao-Rao Wang Cheng-Lin Lu +1 位作者 Gang Wang Dong-Sheng Zhang 《International Journal of Oral Science》 SCIE CAS CSCD 2014年第2期99-104,共6页
The purpose of this study was to investigate how cyclic loading influenced the fracture toughness of hot-press lithium disilicate and zirconia core materials and whether there was an increase in the propensity for cro... The purpose of this study was to investigate how cyclic loading influenced the fracture toughness of hot-press lithium disilicate and zirconia core materials and whether there was an increase in the propensity for crown failure. Two types of all-ceramic crowns including the IPS e.max Press system (n=24) and the Lava zirconia system (n=24), were selected. Sectioned specimens were subjected to cyclic loading with the maximum magnitude of 200 N (R=0.1) until two million cycles. The material properties including Young's modulus (E) and hardness (H) and the fracture toughness (K,c) of the core materials were evaluated using indentation methods (n= 12 each). The load-bearing capacities of the specimens were examined by means of monotonic load to fracture (n=12 each). It was found that the material properties, including E, Hand Knc, of the two types of dental ceramics, were reduced. Statistical analysis indicated that there were no significant influences of fatigue loading on material properties E and H for both types of dental ceramics or Kgc for zirconia, while for the IPS e.max Press core, K,c, which was parallel to the direction of the lithium disilicate crystals, was significantly reduced (P-0.001). A conclusion was drawn that zirconia possesses high mechanical reliability and sustainable capacity to resist fatigue loading, while fatigue loading remarkably degraded the anisotropic mechanical behaviour of hot-press lithium disilicate ceramics. 展开更多
关键词 dental ceramics fatigue loading fracture toughness load-bearing capacity
下载PDF
Bearing capacity and mechanical behavior of CFG pile composite foundation
20
作者 陈秋南 赵明华 +1 位作者 周国华 张主华 《Journal of Central South University》 SCIE EI CAS 2008年第S2期45-49,共5页
CFG pile (i.e., pile constructed by granular materials of cement, fly-ash and gravel) composite foundation is applied in subsoil treatment widely and successfully. In order to have a further study of this kind of subs... CFG pile (i.e., pile constructed by granular materials of cement, fly-ash and gravel) composite foundation is applied in subsoil treatment widely and successfully. In order to have a further study of this kind of subsoil treatment technology, the influencing factors and calculation methods of the vertical bearing capacity of single CFG pile and the CFG pile composite foundation were discussed respectively. And based on the obtained solutions, effects by the cushion and measurements to reduce negative friction area were analyzed. Moreover, the developing law of settlement and bearing capacity eigenvalue controlled by the material strength with the increase of load were given for the CFG composite foundation. The in-situ static load test was tested for CFG pile. The results of test show that the maximum test load or half of the ultimate load is used from all the points of test, the average bearing capacity eigenvalue of single pile is 390 kN, and slightly greater than the design value of bearing capacity. The bearing capacity eigenvalues of composite foundation for 3 piles are greater than 300 kPa, and the mechanical properties of CFG pile composite foundation are almost identical in the case of the same load and cushion thickness. The pile-soil stress ratio and the load-sharing ratio can be adjusted through setting up cushion thickness. 展开更多
关键词 CFG PILE composite FOUNDATION properties of bearing capacity in-situ static load PILE-SOIL stress ratio
下载PDF
上一页 1 2 201 下一页 到第
使用帮助 返回顶部