Solvent de binding of water soluble binder in powder injection moulding

The solvent debinding of water soluble binder in powder injection moulding (MIM) was investigated systematically, including the effects of solvent types, temperature and the thickness of green parts on the solvent debinding rate. After studying the debinding of a green part with a thickness of 4.26 mm, it was found that, the debinding rate of polyethylene glycol(PEG) in water and alcohol was high initially, and then decreased; however, it would increase with temperature increasing. At room temperature, the dissolution rate of PEG in water was higher than that in alcohol, but the latter would be much faster with temperature increasing because the debinding activation energy in alcohol was 51.44 kJ·mol -1 ·K -1 , much higher than 24.23 kJ·mol -1 ·K -1 in water. With a green part thickness larger than 4.26 mm, the debinding was controlled by diffusion; but with that smaller than 2.36 mm, the debinding was controlled by both dissolution and diffusion.

Fabrication and properties of binder for powder extrusion molding

By optimizing formulation and fabrication methods, a new binder forplasticizing powder extrusion molding of hard metal, with excellent integrated properties anduniform distribution characters, has been developed. Thermal debonding mechanism and the extrudingtheological behaviours have been studied. The technology of fabrication of binder and thermaldebonding process have also been investigated. Using the novel binder, the hard-metalextrusion-molding rods with diameter up to 25mm, have been manufactured.

Properties of diamond tool binders with fine carbonyl Ni powder additions

Fine Ni powder is often added to Co and bronze-based metal binder powders for diamond tool segments.Ni is a lower cost substitute for extra-fine Co powder and increases the toughness of Co-Fe diamond binders at the expense of lower hardness and bend strength.In bronze-based diamond binder segments,Ni increases hardness and yield strength.Several grades of Ni powder are used commercially with both Co and bronze-based diamond binders.This paper compares properties of diamond binders containing carbonyl Ni powders including standard Inco(?) T255,T123 PM and T 110 PM.Binder materials were made by ball milling or dry mixing of the fine carbonyl Ni and Fe powders with either XF Co or air atomized bronze(90/10 Cu/Sn) powders.Co-based powder blends were hot pressed at 20～35 MPa and 700℃to 900℃.Bronze-based powder blends were cold pressed and sintered at 840℃.Apparent density,apparent hardness and bend strength(TRS) were compared for different binder compositions and processing conditions.

A novel binder and binder extraction method for powder injection molding of tungsten cemented carbide

An improved wax based multi component binder and a new debinding method termed high pressure condensed solvent extraction were developed for powder injection molding of tungsten cemented carbide. The results indicate that a critical powder loading of 65% (volume fraction) and an ideal rheological properties were obtained by the feedstock based on the binder. High debinding rate and specimens with high strength were obtained by the debinding method. Moreover, by making high temperature holding time adjustable, it makes the subsequent thermal degradation process more flexible to debinding atmosphere and carbon content of the as debinded specimens controllable. The transverse rupture strength, hardness and density of the as sintered specimens made by an optimized PIM process are 2.48 GPa, HRA90 and 14.72 g/cm 3, respectively. Good shape retention and about 0.02% dimension deviation were achieved.

Research and Application Status and Development Trend of Alkali-Activated Binder Powder for Mine Backfill

To improve the economic and social benefits of mining and backfill,it is necessary to find the backfill materials suitable for mineral mining,improve the various properties of the filling materials,and develop low cost,high performance new filling materials.Portland cement is neither environmentally friendly nor economical.Currently,we have begun to study and apply some industrial waste,such as slag,fly ash,and other solid wastes,with certain activities as the primary component of cementing material that will not only meet the technical requirements of filling,but also comprehensively utilize industrial waste and possess a benign,sustainable lifecycle for environmental protection.This study expounds the composition and reaction mechanism of alkali-activated binder powder used for cemented paste backfill material,summarizes the research and application status of alkaliactivated binder powders,including mechanics,durability,economic and environmental,and discusses future development directions for mine binder powders.It needs to continue to expand the utilization range of solid waste and improve the utilization rate of solid waste in the future.The development and research of this binder powder plays an important role in the progress of filling technologies.Hence,the research about alkali-activated binder powder contains great development potential and broad prospects.

Form and Mechanism of Sulfate Attack on Cement-based Material Made of Limestone Powder at Low Water-binder Ratio under Low Temperature Conditions

The development of strength and the form of attack of cement-based material made of limestone powder at low water-binder ratio under low-temperature sulfate environment were studied. The results indicate that when water-binder ratio is lower than 0.40, the cement-based material with limestone powder has insignificant change in appearance after being soaked in 10% magnesium sulfate solution at low temperature for 120 d, and has significant change in appearance after being soaked at the age of 200 d. Expansion damage and exfoliation occur on the surface of concrete test cube at different levels. When limestone powder accounts for about 28 percent of cementitious material, with the decrease of water-binder ratio, the compressive strength loss has gradually decreased after the material is soaked in the magnesium sulfate solution at low temperature at the age of 200 d. After the specimen with the water-binder ratio of less than 0.4 and the limestone powder volume of greater than 20% is soaked in 10% magnesium sulfate solution at low temperature at the age of 200 d, gypsum attack-led destruction is caused to the concrete test cube, without thaumasite sulfate attack.

Chemistry principles for thermoplastic polymer binder formula selection for powder injection molding

The polymer binder selection is one of the very important aspects for the powder injection molding. However,even nowadays the binder selection is still mainly performed by try and error method. Six commercial or intensive studied binder fo rmulas were analyzed according to state diagram and chemical characteristics of ingredients in each binder formula. In addition,the interactions between the bi nder components and additives were also taken into account. Based on the analysi s,the optimum binder formula was selected and some selection criterions were pu t forward for the binder and additives.

Effect of Binder on the Structure and Properties of Silicon Powder-supported TiO_2 Photocatalysis Material

Recoverable TiO2 photocatalysis material supported by silicon powder was prepared with sol-gel method, afterwards the silica gol and sodium silicate were used as molding binder respectively to investigate their effects （including binder type and binder addition quantity） on the crystal structure and catalysis properties of photocatalyst. In this work, the catalysis activity was defined as the degradation rate of methyl orange solution upon ultraviolet lamp irradiation, and the specific areas were determined with nitrogen desorption method. TiO2 crystal form was measured with X-ray powder diffraction and their micro-morphology was observed with SEM. Experimental results indicate that these two binders do not affect the crystal form transformation of TiO2, but silica gol can increase the specific surface area of TiO2 photocatalyst obviously and the addition of sodium silicate can decrease it. In all, silica gol is a better candidate than sodium silicate for higher catalysis property. In conclusion, 6% silica gol is the optimal addition concentration. Under this condition, the ratio of anatase to rutile TiO2 is 64：36, the specific area is 29.67 m^2/g, and as expected, the degradation rate of methyl orange could be as high as 90% after irradiation for 5 days.

Development of Novel Binder for Hardmetal Powder Extrusion Molding

A novel binder system for hardmetal powder extrusion moulding (PEM) process has been developed. The binder system comprises a major fraction of a mixture of low molecular weight components (LMWCs) and a minor fraction of very finely dispersed polymer. The feedstocks are mixed as a thick slurry at a suitable temperature and are rapidly homogenized by stirring at an adequate shear force. The binders are removed by thermal debinding. The thermal debinding mechanism has been investigated by thermogravimetry (TG) and differential thermogravimetry (DTG). At the first stage of debinding, the LMWCs are removed. These open up pore channels which allows much faster removal of the remaining polymer component during the subsequent stage. The microstructures of the moulded green parts were observed by scanning electron microscopy (SEM). The debound samples were sintered at different temperatures, and the sintered samples properties were measured.

Part 1: Synthesis and Evaluation of Novel Nano Scale Powdered Polyurethane Acrylate Binders

Some new an aqueous polyurethane acrylate (waterborne binder) based on polyethylene glycol with different M. wt. mixed with polyol were carried out. Seven different polyurethane acrylate co-polymers were prepared aiming at substituting the two hydroxyl groups of polyethylene glycol (6000, 12,000 and 20,000 g/mol) and two primary hydroxyl groups of polyol through their reaction with corresponding calculated amounts of either isophorone diisoyanate or toluene diisocyanate and caped the remaining isocyanate group with either hydroxy ethyl acrylate or hydroxy propyl methacrylate to get on the polyurethane acrylate polymers [PUA]. From DSC measurement the result of Tg of synthesized PUA are in range from -8.78℃ to 36.4℃. So they can classify as soft binders. The infrared spectra, rheological properties, viscosity measurement, the weight average molecular weight, of the synthesize binders were investigated.

Influence of binder composition on the rheological behavior of injection-molded microsized SiC suspensions

The influence of four kinds of binders consisting of paraffin wax （PW）, random-polypropylene （RPP）, high-density polyethylene （HDPE）, and stearic acid （SA） on the theological behavior of injection-molded SiC feedstocks was investigated over a temperature range of 150℃ to 180℃ and a shear rate range of 4 s^-1 to 1259 s^^-1. The results showed that all the feedstocks exhibited pseudoplastic flow behavior. The wax-based binder of multipolymer components （PW-RPP-HDPE） exhibited better comprehensive rheological properties compared with the binder of monopolymer components （PW-RPP or PW-HDPE）. The addition of 5wt% SA to the binder could reduce the viscosity of the feedstock but enhance the rheological stability by improving the wettability between the binder and the SiC powder. The binder of 65wt% PW ＋ 15wt% HDPE ＋ 15wt% RPP ＋ 5wt% SA was found to be a better binder for microsized SiC injection molding.

Thermal debinding dynamics of novel binder system

The thermal debinding dynamics of newly developed binders for cemented carbides extrusion molding was studied. It is shown that the thermal debinding processes can be divided into two stages: low temperature region, in which the low molecular mass components (LMMCs) are removed; and high temperature region, in which the polymer components are removed. The rate of thermal debinding is controlled by diffusion mechanism. The thermal debinding activation energies were solved out by differential method and integral method. The results show that the addition of other components acted as a catalyzer can effectively decrease the activation energy of thermal debinding processes.

Binder composition and debinding process in PIM of AlN

The thermal degradation behaviors of AlN green specimens were studied by thermogravimetry analysis during the ceramic powder injection molding debinding process. The optimum binder composition and the debinding cycle were demonstrated by observing the TGA and DTA plots of AlN green specimens and analyzing the microstructure at different temperatures. By adding HDPE into the PW EVA binder used in powder injection molding AlN can effectively reduce the mass lose rate in debinding process and improve the shape retention ability. At last, aluminum nitride ceramic with high room temperature thermal conductivity of 162.5?W·m -1 ·K -1 was produced. [

Debinding and sintering of warm compacted and binder-treated complex iron-base part

Regular elemental powders were used in warm flow compaction instead of the expensive micron-sized powders to fabricate cross-shaped parts. Debinding behaviors,sintering properties and shape consistency of the sintered parts were studied. Binder removal was accomplished by heating green compacts at intermediate temperatures with optimal heating rates until the debinding temperature was reached. Results show that by controlling debinding process,complex parts with good shape consistence can be obtained by warm compaction of binder-treated powder. Fine and shiny surface was obtained and no surface defect can be observed for sintered parts debinded at 2 ℃/min,while defect can be observed in sintered parts debinded at 4 ℃/min.

A STUDY OF HIGH LOFT NONWOVEN FABRICS USING POWDER BONDING TECHNOLOGY

In this paper, two types of high loft nonwoven fabrics have been constructed in the laboratory apparatus made by ourselves with different binders (polyamide and polyethylene powder) and varying binder contents (10%, 20%, 30% and 40%). The tensile and compression properties of these nonwoven fabrics were tested. It was found that one can reduce powder binder content to increase loft and softness of nonwoven fabrics, but it has to sacrifice its tensile strength. Adhesion force between binder and single fibre was also explored. The experiments showed that the adhesion force at the interface between binder and fibre depends on the fibre variety, the fibre surface morphology, heating temperature and heating time etc..

Rheologic behavior and PIM processing of WC-TiC-Co powder feedstock

An improved wax-based binder was developed for the powder injection molding (PIM) of WC-TiC-Co cemented carbides. The critical powder loading and the rheologic behavior of the feedstock were determined. It was found that the critical powder loading could achieve up to 62.5% (volume fraction) and the feedstock exhibited a pseudo-plastic flow behavior. The injection molding, debinding and sintering processes were studied. The dimension deviation of the sintered samples could be controlled in the range of ±0.2% with the optimized processing parameters and the mechanical properties were better than or equivalent to those of the same alloy made by conventional press-sintering process.

Rheologic behavior and PIM processing of WC-TiC-Co powder feedstock

An improved wax-based binder was developed for the powder injection molding(PIM) of WC-TiC-Co cemented carbides. The critical powder loading and the rheologic behavior of thefeedstock were determined. It was found that the critical powder loading could achieve up to 62.5percent (volume fraction) and the feedstock exhibited a pseudo-plastic flow behavior. The injectionmolding, debinding and sintering processes were studied. The dimension deviation of the sinteredsamples could be controlled in the range of + -0.2 percent with the optimized processing parametersand the mechanical properties were better than or equivalent to those of the same alloy made byconventional press-sintering process.

陶瓷结合剂金刚石团聚磨料探索

细粒度金刚石微粉大量积压是目前金刚石微粉制造行业面临的问题之一,为促进其应用,以铝硼硅结合剂为黏接剂、Si粉和Ti粉为添加剂制造团聚磨料试样,并将制成的团聚磨料加入铝硼硅结合剂中制成陶瓷结合剂试样,对所制试样的抗弯强度、物相构成和微观形貌进行分析。结果表明:添加Si或Ti的铝硼硅黏结剂均能起到团聚金刚石的作用;当团聚磨料中Si或Ti的质量分数为10.0%时,所制得的陶瓷结合剂试样抗弯强度最大,且添加Si的团聚磨料试样抗弯强度为43.74 MPa;当Si或Ti的质量分数超过10.0%时,团聚磨料试样中出现大量Si或者TiO2峰,其抗弯强度急剧下降;添加Si的团聚磨料试样与添加Ti的团聚磨料试样相比,其具有更大的粒度和更均匀的粒度分布,添加Si的铝硼硅黏结剂可将1~2μm的磨料团聚为5~10μm的磨料。

先进陶瓷黏结剂喷射增材制造技术发展与展望

在过去的20年中,陶瓷黏结剂喷射增材制造技术已经成为制造复杂陶瓷构件的一种革命性方法,特别是在航空航天、生物医疗、电子信息等多个关键领域展现出显著的应用潜力与价值。本文全面回顾了此技术的基础原理、材料选择、工艺流程、性能特征及制造缺陷,并针对未来的挑战和目标进行了深入展望。文中首先详细概述了该技术的成型原理,对其与其他增材制造工艺的优势和局限进行了对比分析;然后综合总结了国际研究进展,重点包括陶瓷粉末的性能与处理、黏结剂的配置与其在粉床中的动力学行为、工艺参数的调整与后续致密化工艺,并讨论了这些因素如何影响初坯和最终制件的密度、孔隙结构、组织特性及性能;最后,基于现有研究成果和应用局限,本文对粉末原材料、黏结剂的设计、工艺参数优化等方面提出了前瞻性的发展建议。本篇综述旨在为理解和应用陶瓷黏结剂喷射增材制造提供全面的科学研究和工程实践指导。

Rheological characteristics of aged asphalt binder

Different aging levels(RTFOT,PAV-10h,PAV-20h and PAV-30 h) of asphalt binders with various mass ratios of mineral powder to asphalt(0,0.4,0.8,1.2,1.6,2.0) were used to investigate the rheological properties of aged asphalt binders with respect to their short and long terms aging characteristics.Viscosity test,dynamic shear test and creep test were conducted.The test results indicate that the viscosity of aged asphalt binder increases sharply with the extension of aging period.Complex shear modulus of aged asphalt increases,which indicates that the stiffness of asphalt binders can increase.The phase angle for aged asphalt binders reduces,which indicates that the elastic portion for viscoelastic property of asphalt binders increases.|G*|·sin δ increases after aging procedure which means that the fatigue resistance becomes poor.The creep test results show that creep strain curves varies remarkably for virgin and aged asphalt binders.The total strain during loading period and the permanent strain decreases significantly for aged asphalt binders,which implies that the elastic portion increases and the viscous portion decreases.