The relation between friction mechanism and force chains characteristics has not yet been fully studied in the powder metallurgy research area.In this work,a uniaxial compression discrete element model is established ...The relation between friction mechanism and force chains characteristics has not yet been fully studied in the powder metallurgy research area.In this work,a uniaxial compression discrete element model is established based on the compaction process of ferrous powder.Furthermore,the correlation mechanism between force chains and the friction mechanism during powder compaction is investigated.The simulation results reveal a strong correlation between the variation of the friction coefficient and the evolution of force chains.During the powder compaction,the friction coefficient would eventually tend to be stable,a feature which is also closely related to the slip ratio between particles.The side wall friction and the friction between particles would have an important effect on the direction of force chain growth in about one-third of the area near the side wall.The research results provide theoretical guidance for improving the densification process of the powder according to the force chain and friction.展开更多
Based on an analysis of the validity of the powder compaction equation of Kawakita,a modified compaction equation is proposed.It is shown by the statistical analysis on the experimental compaction data of various powd...Based on an analysis of the validity of the powder compaction equation of Kawakita,a modified compaction equation is proposed.It is shown by the statistical analysis on the experimental compaction data of various powders that in most cases the proposed equation provides a better description of the compaction data than Kawakita's equation,especially in the cases of the compaction of hard material powders.展开更多
Compaction processes are one the most important par ts of powder forming technology. The main applications are focused on pieces for a utomotive, aeronautic, electric and electronic industries. The main goals of the c...Compaction processes are one the most important par ts of powder forming technology. The main applications are focused on pieces for a utomotive, aeronautic, electric and electronic industries. The main goals of the compaction processes are to obtain a compact with the geometrical requirements, without cracks, and with a uniform distribution of density. Design of such proc esses consist, essentially, in determine the sequence and relative displacements of die and punches in order to achieve such goals. A.B. Khoei presented a gener al framework for the finite element simulation of powder forming processes based on the following aspects; a large displacement formulation, centred on a total and updated Lagrangian formulation; an adaptive finite element strategy based on error estimates and automatic remeshing techniques; a cap model based on a hard ening rule in modelling of the highly non-linear behaviour of material; and the use of an efficient contact algorithm in the context of an interface element fo rmulation. In these references, the non-linear behaviour of powder was adequately desc ribed by the cap plasticity model. However, it suffers from a serious deficiency when the stress-point reaches a yield surface. In the flow theory of plasticit y, the transition from an elastic state to an elasto-plastic state appears more or less abruptly. For powder material it is very difficult to define the locati on of yield surface, because there is no distinct transition from elastic to ela stic-plastic behaviour. Results of experimental test on some hard met al powder show that the plastic effects were begun immediately upon loading. In such mater ials the domain of the yield surface would collapse to a point, so making the di rection of plastic increment indeterminate, because all directions are normal to a point. Thus, the classical plasticity theory cannot deal with such materials and an advanced constitutive theory is necessary. In the present paper, the constitutive equations of powder materials will be discussed via an endochronic theory of plasticity. This theory provides a unifi ed point of view to describe the elastic-plastic behaviour of material since it places no requirement for a yield surface and a ’loading function’ to disting uish between loading an unloading. Endochronic theory of plasticity has been app lied to a number of metallic materials, concrete and sand, but to the knowledge of authors, no numerical scheme of the model has been applied to powder material . In the present paper, a new approach is developed based on an endochronic rate independent, density-dependent plasticity model for describing the isothermal deformation behavior of metal powder at low homologous temperature. Although the concept of yield surface has not been explicitly assumed in endochronic theory, it is shown that the cone-cap plasticity yield surface (Fig.1), which is the m ost commonly used plasticity models for describing the behavior of powder materi al can be easily derived as a special case of the proposed endochronic theory. Fig.1 Trace of cone-cap yield function on the meridian pl ane for different relative density As large deformation is observed in powder compaction process, a hypoelastic-pl astic formulation is developed in the context of finite deformation plasticity. Constitutive equations are stated in unrotated frame of reference that greatly s implifies endochronic constitutive relation in finite plasticity. Constitutive e quations of the endochronic theory and their numerical integration are establish ed and procedures for determining material parameters of the model are demonstra ted. Finally, the numerical schemes are examined for efficiency in the model ling of a tip shaped component, as shown in Fig.2. Fig.2 A shaped tip component. a) Geometry, boundary conditio n and finite element mesh; b) density distribution at final stage of展开更多
The effects of temperature (0-500°C) on the compressive strength,hardness,average relative density,and microstructure of Ti6Al4V powder green compacts prepared by magnetic pulse compaction were investigated.The...The effects of temperature (0-500°C) on the compressive strength,hardness,average relative density,and microstructure of Ti6Al4V powder green compacts prepared by magnetic pulse compaction were investigated.The results show that with increasing heating temperature,the compressive strength first increases and then decreases with the maximum value of 976.74 MPa at 400°C.The average relative density and hardness constantly increase,and their values reach 96.11% and HRA 69.8 at 500°C,respectively.The increase of partial welding is found among the junctions of particles inside the compacts; there is no obvious grain growth inside the compacts within the temperature range.展开更多
Ti6Al4V powder compaction was performed by using magnetic pulse compaction in air at 200℃.Effects of process parameters such as voltage,capacitance,discharge times on the microstructure,compressive strength,hardness ...Ti6Al4V powder compaction was performed by using magnetic pulse compaction in air at 200℃.Effects of process parameters such as voltage,capacitance,discharge times on the microstructure,compressive strength,hardness and relative density of compacts were investigated.The experimental results show that the relative density,hardness and compressive strength of compacted specimens increase with increasing voltage.In addition,the relative density and compressive strength of compacted specimens increase with the augmentation of capacitance in the range investigated.The relative density increases,the hardness firstly increases and then tends to be a fixed value;and the compressive strength firstly increases and then decreases from one to five times compaction.Both values of the hardness and compressive strength reach the maxima of HRA 69.1 and 1 062.31 MPa,at three times compaction,respectively.There are pores in and between particles.展开更多
The low-voltage-electromagnetic forming was applied to powder compaction.A series of experiments was performed to compact aluminum,copper and tin powders in an indirect working way.Having compacted high-density powder...The low-voltage-electromagnetic forming was applied to powder compaction.A series of experiments was performed to compact aluminum,copper and tin powders in an indirect working way.Having compacted high-density powder parts successfully,the authors analyzed the effects of voltage,capacitance,friction,compaction times,powder size and other factors on the densities of compacted specimens.The experimental results show that lower voltage but larger capacitance are beneficial to increasing the density and homogeneity of the compacted specimens,if the loading velocity and discharging energy are suitable.The higher the voltage,the greater the percentage of energy consumed by friction.If the equipment energy is limited,the iterative compaction is an efficient way to manufacture homogeneous and high-density powder parts.展开更多
A new technique, powder compact foaming process for the production of aluminumfoams has been studied in this article. According to this method, the aluminum pow-der is mixed with a powder foaming agent (TiH_2). Subseq...A new technique, powder compact foaming process for the production of aluminumfoams has been studied in this article. According to this method, the aluminum pow-der is mixed with a powder foaming agent (TiH_2). Subsequent to mixing, the powderblend is hot compacted to obtain a dense semi--finished product. Upon heating to tem-peratures within the range of the melting point, the foaming agent decomposes to evolvegas and the semi--finished product expands into a porous cellular aluminum. Foamingprocess is the key in this method. Based on experiments, the foaming characteris-tics were mainly analyzed and discussed. Experiments show that the aluminum--foamwith closed pores and a uniform cell structure of high porosity can be obtained usingthis method by adjusting the foaming parameters: the content of foaming agent andfoaming temperature.展开更多
This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface wi...This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.展开更多
Magnesium has wide application in industry.The main purpose of this investigation was to improve the properties of magnesium by reinforcing it using B4C nanoparticles.The reinforced nanocomposites were fabricated usin...Magnesium has wide application in industry.The main purpose of this investigation was to improve the properties of magnesium by reinforcing it using B4C nanoparticles.The reinforced nanocomposites were fabricated using a powder compaction technique for 0,1.5vol%,3vol%,5vol%,and 10vol% of B4C.Powder compaction was conducted using a split Hopkinson bar(SHB),drop hammer(DH),and Instron to reach different compaction loading rates.The compressive stress–strain curves of the samples were captured from quasi-static and dynamic tests carried out using an Instron and split Hopkinson pressure bar,respectively.Results revealed that,to achieve the highest improvement in ultimate strength,the contents of B4C were 1.5vol%,3vol%,and 3vol% for Instron,DH,and SHB,respectively.These results also indicated that the effect of compaction type on the quasi-static strength of the samples was not as significant,although its effect on the dynamic strength of the samples was remarkable.The improvement in ultimate strength obtained from the quasi-static stress–strain curves of the samples(compared to pure Mg)varied from 9.9% for DH to 24% for SHB.The dynamic strength of the samples was improved(with respect to pure Mg)by 73%,116%,and 141%for the specimens compacted by Instron,DH,and SHB,respectively.The improvement in strength was believed to be due to strengthening mechanisms,friction,adiabatic heating,and shock waves.展开更多
During the production of pharmaceutical tablets using powder compaction, certain common problems can occur, such as sticking, tearing, cutting, and lamination. In the past, the compressibility of the powder was calcul...During the production of pharmaceutical tablets using powder compaction, certain common problems can occur, such as sticking, tearing, cutting, and lamination. In the past, the compressibility of the powder was calculated only along the axis of the device; consequently, critical areas of the material throughout the volume could not be identified. Therefore, finite element method (FEM) can be used to predict these defects in conjunction with the use of an appropriate constitutive model. This article summarizes the current research in the field of powder compaction, describes the Drucker-Prager Cap model calibration procedure and its implementation in FEM, and also examines the mechanical behavior of powder during compaction. In addition, the mechanical behavior of pharmaceutical powders in relation to changes in friction at the wall of the system is examined, and the dependence of lubrication effect on the geometry of the compaction space is also investigated. The influence of friction on the compaction process for the flat-face, fiat-face radius edge, and standard convex tablets is examined while highlighting how the effects of friction change depending on the shape of these tablets.展开更多
The flow behaviour of powders from a stationary shoe into a moving die, which mimics the die filling process in a rotary tablet press, was analysed using a discrete element method (DEM), in which 2D irregular shaped...The flow behaviour of powders from a stationary shoe into a moving die, which mimics the die filling process in a rotary tablet press, was analysed using a discrete element method (DEM), in which 2D irregular shaped particles were considered. The influence of the particle shape, size and size distribution, the number of particles used in the simulation, the initial height of powder bed in the shoe, and the filling speed on the average mass flow rate and the critical filling speed (the highest speed at which the die can be completely filled) were explored. It has been found that a maximum flow rate is obtained at the critical filling speed for all systems investigated and poly-disperse systems have higher mass flow rates and higher critical filling speeds than mono-disperse systems. In addition, the powder with particles which can tessellate generally has a lower filling rate and a lower critical titling speed.展开更多
基金supported by the Natural Science Foundation of Fujian Province,China(Grant No.2020J01869)the Initial Scientific Research Fund in Fujian University of Technology,China(Grant No.GY-Z19123)the Fujian Provincial Science and Technology Guiding Project,China(Grant No.2017H0002)。
文摘The relation between friction mechanism and force chains characteristics has not yet been fully studied in the powder metallurgy research area.In this work,a uniaxial compression discrete element model is established based on the compaction process of ferrous powder.Furthermore,the correlation mechanism between force chains and the friction mechanism during powder compaction is investigated.The simulation results reveal a strong correlation between the variation of the friction coefficient and the evolution of force chains.During the powder compaction,the friction coefficient would eventually tend to be stable,a feature which is also closely related to the slip ratio between particles.The side wall friction and the friction between particles would have an important effect on the direction of force chain growth in about one-third of the area near the side wall.The research results provide theoretical guidance for improving the densification process of the powder according to the force chain and friction.
文摘Based on an analysis of the validity of the powder compaction equation of Kawakita,a modified compaction equation is proposed.It is shown by the statistical analysis on the experimental compaction data of various powders that in most cases the proposed equation provides a better description of the compaction data than Kawakita's equation,especially in the cases of the compaction of hard material powders.
文摘Compaction processes are one the most important par ts of powder forming technology. The main applications are focused on pieces for a utomotive, aeronautic, electric and electronic industries. The main goals of the compaction processes are to obtain a compact with the geometrical requirements, without cracks, and with a uniform distribution of density. Design of such proc esses consist, essentially, in determine the sequence and relative displacements of die and punches in order to achieve such goals. A.B. Khoei presented a gener al framework for the finite element simulation of powder forming processes based on the following aspects; a large displacement formulation, centred on a total and updated Lagrangian formulation; an adaptive finite element strategy based on error estimates and automatic remeshing techniques; a cap model based on a hard ening rule in modelling of the highly non-linear behaviour of material; and the use of an efficient contact algorithm in the context of an interface element fo rmulation. In these references, the non-linear behaviour of powder was adequately desc ribed by the cap plasticity model. However, it suffers from a serious deficiency when the stress-point reaches a yield surface. In the flow theory of plasticit y, the transition from an elastic state to an elasto-plastic state appears more or less abruptly. For powder material it is very difficult to define the locati on of yield surface, because there is no distinct transition from elastic to ela stic-plastic behaviour. Results of experimental test on some hard met al powder show that the plastic effects were begun immediately upon loading. In such mater ials the domain of the yield surface would collapse to a point, so making the di rection of plastic increment indeterminate, because all directions are normal to a point. Thus, the classical plasticity theory cannot deal with such materials and an advanced constitutive theory is necessary. In the present paper, the constitutive equations of powder materials will be discussed via an endochronic theory of plasticity. This theory provides a unifi ed point of view to describe the elastic-plastic behaviour of material since it places no requirement for a yield surface and a ’loading function’ to disting uish between loading an unloading. Endochronic theory of plasticity has been app lied to a number of metallic materials, concrete and sand, but to the knowledge of authors, no numerical scheme of the model has been applied to powder material . In the present paper, a new approach is developed based on an endochronic rate independent, density-dependent plasticity model for describing the isothermal deformation behavior of metal powder at low homologous temperature. Although the concept of yield surface has not been explicitly assumed in endochronic theory, it is shown that the cone-cap plasticity yield surface (Fig.1), which is the m ost commonly used plasticity models for describing the behavior of powder materi al can be easily derived as a special case of the proposed endochronic theory. Fig.1 Trace of cone-cap yield function on the meridian pl ane for different relative density As large deformation is observed in powder compaction process, a hypoelastic-pl astic formulation is developed in the context of finite deformation plasticity. Constitutive equations are stated in unrotated frame of reference that greatly s implifies endochronic constitutive relation in finite plasticity. Constitutive e quations of the endochronic theory and their numerical integration are establish ed and procedures for determining material parameters of the model are demonstra ted. Finally, the numerical schemes are examined for efficiency in the model ling of a tip shaped component, as shown in Fig.2. Fig.2 A shaped tip component. a) Geometry, boundary conditio n and finite element mesh; b) density distribution at final stage of
文摘The effects of temperature (0-500°C) on the compressive strength,hardness,average relative density,and microstructure of Ti6Al4V powder green compacts prepared by magnetic pulse compaction were investigated.The results show that with increasing heating temperature,the compressive strength first increases and then decreases with the maximum value of 976.74 MPa at 400°C.The average relative density and hardness constantly increase,and their values reach 96.11% and HRA 69.8 at 500°C,respectively.The increase of partial welding is found among the junctions of particles inside the compacts; there is no obvious grain growth inside the compacts within the temperature range.
文摘Ti6Al4V powder compaction was performed by using magnetic pulse compaction in air at 200℃.Effects of process parameters such as voltage,capacitance,discharge times on the microstructure,compressive strength,hardness and relative density of compacts were investigated.The experimental results show that the relative density,hardness and compressive strength of compacted specimens increase with increasing voltage.In addition,the relative density and compressive strength of compacted specimens increase with the augmentation of capacitance in the range investigated.The relative density increases,the hardness firstly increases and then tends to be a fixed value;and the compressive strength firstly increases and then decreases from one to five times compaction.Both values of the hardness and compressive strength reach the maxima of HRA 69.1 and 1 062.31 MPa,at three times compaction,respectively.There are pores in and between particles.
文摘The low-voltage-electromagnetic forming was applied to powder compaction.A series of experiments was performed to compact aluminum,copper and tin powders in an indirect working way.Having compacted high-density powder parts successfully,the authors analyzed the effects of voltage,capacitance,friction,compaction times,powder size and other factors on the densities of compacted specimens.The experimental results show that lower voltage but larger capacitance are beneficial to increasing the density and homogeneity of the compacted specimens,if the loading velocity and discharging energy are suitable.The higher the voltage,the greater the percentage of energy consumed by friction.If the equipment energy is limited,the iterative compaction is an efficient way to manufacture homogeneous and high-density powder parts.
文摘A new technique, powder compact foaming process for the production of aluminumfoams has been studied in this article. According to this method, the aluminum pow-der is mixed with a powder foaming agent (TiH_2). Subsequent to mixing, the powderblend is hot compacted to obtain a dense semi--finished product. Upon heating to tem-peratures within the range of the melting point, the foaming agent decomposes to evolvegas and the semi--finished product expands into a porous cellular aluminum. Foamingprocess is the key in this method. Based on experiments, the foaming characteris-tics were mainly analyzed and discussed. Experiments show that the aluminum--foamwith closed pores and a uniform cell structure of high porosity can be obtained usingthis method by adjusting the foaming parameters: the content of foaming agent andfoaming temperature.
文摘This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.
文摘Magnesium has wide application in industry.The main purpose of this investigation was to improve the properties of magnesium by reinforcing it using B4C nanoparticles.The reinforced nanocomposites were fabricated using a powder compaction technique for 0,1.5vol%,3vol%,5vol%,and 10vol% of B4C.Powder compaction was conducted using a split Hopkinson bar(SHB),drop hammer(DH),and Instron to reach different compaction loading rates.The compressive stress–strain curves of the samples were captured from quasi-static and dynamic tests carried out using an Instron and split Hopkinson pressure bar,respectively.Results revealed that,to achieve the highest improvement in ultimate strength,the contents of B4C were 1.5vol%,3vol%,and 3vol% for Instron,DH,and SHB,respectively.These results also indicated that the effect of compaction type on the quasi-static strength of the samples was not as significant,although its effect on the dynamic strength of the samples was remarkable.The improvement in ultimate strength obtained from the quasi-static stress–strain curves of the samples(compared to pure Mg)varied from 9.9% for DH to 24% for SHB.The dynamic strength of the samples was improved(with respect to pure Mg)by 73%,116%,and 141%for the specimens compacted by Instron,DH,and SHB,respectively.The improvement in strength was believed to be due to strengthening mechanisms,friction,adiabatic heating,and shock waves.
基金supported by the Scientific Grant Agency of the Ministry of Education of the Slovak Republic for the research project,titled"Basic Research of the Operations in the Mechanics of Particulate Material"No.1/0652/13the Slovak University of Technology to support young researchers(Grant No.1312)/2013
文摘During the production of pharmaceutical tablets using powder compaction, certain common problems can occur, such as sticking, tearing, cutting, and lamination. In the past, the compressibility of the powder was calculated only along the axis of the device; consequently, critical areas of the material throughout the volume could not be identified. Therefore, finite element method (FEM) can be used to predict these defects in conjunction with the use of an appropriate constitutive model. This article summarizes the current research in the field of powder compaction, describes the Drucker-Prager Cap model calibration procedure and its implementation in FEM, and also examines the mechanical behavior of powder during compaction. In addition, the mechanical behavior of pharmaceutical powders in relation to changes in friction at the wall of the system is examined, and the dependence of lubrication effect on the geometry of the compaction space is also investigated. The influence of friction on the compaction process for the flat-face, fiat-face radius edge, and standard convex tablets is examined while highlighting how the effects of friction change depending on the shape of these tablets.
基金support from the Engineering and Physical Sciences Research Council (EPSRC), United Kingdom, through an EPSRC Advanced Research Fellowship award (Grants No: EP/C545230 and EP/C545249)
文摘The flow behaviour of powders from a stationary shoe into a moving die, which mimics the die filling process in a rotary tablet press, was analysed using a discrete element method (DEM), in which 2D irregular shaped particles were considered. The influence of the particle shape, size and size distribution, the number of particles used in the simulation, the initial height of powder bed in the shoe, and the filling speed on the average mass flow rate and the critical filling speed (the highest speed at which the die can be completely filled) were explored. It has been found that a maximum flow rate is obtained at the critical filling speed for all systems investigated and poly-disperse systems have higher mass flow rates and higher critical filling speeds than mono-disperse systems. In addition, the powder with particles which can tessellate generally has a lower filling rate and a lower critical titling speed.