Oil-in-water nanoemulsions loaded with lycopene extracts encapsulated by spray drying:Formulation,characterization and optimization

Lycopene is very susceptible to degradation once released from the protective chromoplast environment.In this study,oil-in-water(O/W)nanoemulsions coupled with spray drying technology were applied for the encapsulation and stabilization of lycopene extracted from tomato waste.Tomato extract was obtained by ultrasound-assisted extraction.Nanoemulsions were prepared by a high-speed rotor stator using isopropyl myristate as the oil phase and Pluronic F-127 as the emulsifier for the aqueous external phase.The effect of emulsification process parameters was investigated.Spray drying of the produced emulsions was attempted to obtain a stabilized dry powder after the addition of a coating agent.The effect of different coating agents(maltodextrin,inulin,gum arabic,pectin,whey and polyvinylpyrrolidone),drying temperature(120-170℃),and feed flow rate(3-9 ml·min^(-1))on the obtained particles was evaluated.Results revealed that the emulsion formulation of 20/80(O/W)with 1.5%(mass fraction)of Pluronic F-127 as stabilizer in the aqueous phase resulted in a stable nanoemulsion with droplet sizes in the range of 259-276 nm with a unimodal and sharp size distribution.The extract in the nanoemulsion was well protected at room temperature with a degradation rate of lycopene of about 50%during a month of storage time.The most stable emulsions were then processed by spray drying to obtain a dry powder.Spray drying was particularly successful when using maltodextrin as a coating agent,obtaining dried spherical particles with mean diameters of(4.87±0.17)μm with a smooth surface.The possibility of dissolving the spray dried powder in order to repristinate.The original emulsion was also successfully verified.

Research perspective and prospective of additive manufacturing of biodegradable magnesium-based materials

Biodegradable metals such as magnesium(Mg)and its alloys have attracted extensive attention in biomedical research due to their excellent mechanical properties and biodegradability.However,traditional casting,extrusion,and commercial processing have limitations in manufacturing components with a complex shape/structure,and these processes may produce defects such as cavities and gas pores which can degrade the properties and usefulness of the products.Compared to conventional techniques,additive manufacturing(AM)can be used to precisely control the geometry of workpieces made of different Mg-based materials with multiple geometric scales and produce desirable medical products for orthopedics,dentistry,and other fields.However,a detailed and thorough understanding of the raw materials,manufacturing processes,properties,and applications is required to foster the production of commercial Mg-based biomedical components by AM.This review summarizes recent advances and important issues pertaining to AM of Mg-based biomedical products and discusses future development and application trends.

Expansion Performance and Microstructure of High-performance Concrete using Differently Scaled MgO Agents and Mineral Powder

To investigate the assumptions proposed in this paper,the evolution law governing the strength and expansion performance of MgO and nano-MgO micro-expansive concrete in the environment of mineral powder was firstly observed in this study.Secondly,SEM,XRD,and TG-DSC microscopic tests were conducted to reveal the effects of the active mineral-powder admixture on the hydration degree and expansion performance of MgO and nano-MgO in HPC.Our experimental results successfully verified our hypothesis,which indicated that the expansion performance of macro-MgO and nano-MgO was indeed depressed by the addition of active mineral power admixtures,even though the mechanical property of concrete composites was effectively improved.Furthermore,the hydration test also demonstrated the negative interference on the mineral powders,which was induced by the expansion agents.It is found the amounts of hydrates tend to decrease because the mineral powder ratio reaches and exceeds 40%.Moreover,it is also concluded the effect of expansion agents is governed by the alkalinity cement paste,especially for the nano-MgO.In other words,the expansion performance of nano-MgO will vary more obviously with the hydration process,than MgO.The results of this study provide that effective experimental and theoretical data support the hydration-inhibition mechanism of magnesium expansive agents.

Preparation technology of ultra-fine powders of Auricularia auricular

Conventional mechanical method and mechanical method combined with vacuum freeze-drying technology were used to make the ultra-fine powders of edible fungus (Auricularia auricular). The content of basic nutrients, amino acid, micro structure and their properties of raw edible fungus and the edible fungus powders obtained with the two methods were analyzed and compared. The granularity size and micro-structure of the pulverized samples were analyzed by SEM and TEM technology. The average granularity size of the edible fungus powder obtained with mechanical method was 1–5 μm, while that obtained with mechanical method combined with vacuum freeze-drying process was 0.5–1 μm. The ultra-fine powders of edible fungus obtained with the two methods had better water recovery capability and quality, and their preserving time was longer than that of raw edible fungus. All the properties of the ultra-fine powders of edible fungus obtained with the vacuum freeze-drying technology were evidently superior to that of the conventional mechanical method. Keywords Auricularia auricula - Edible fungus - Ultra-fine powders - Vacuum freeze-drying CLC number TS205 Document code B Biography: YANG Chun-yu (1975), female, Ph. D. in Engineering Technology Center of Forestry and Wood Workine, Machinery, Northeast Forestry University, Harbin 150040, P. R. China.Responsible editor: Zhu Hong

Preparation of ultrafine rhenium powders by CVD hydrogen reduction of volatile rhenium oxides

A novel CVD process for the preparation of ultrafine rhenium powders was investigated using ammonium perrhenate as starting materials. In the process, volatile rhenium oxides, such as ReO4 and Re2O7, were vaporized under a controlled oxidizing atmosphere via the pyrolysis of ammonium perrhenate, and carried into reduction zone by carrier gas, and there reduced into rhenium powders by hydrogen gas. Thermodynamic calculations indicated that Re207 could be prevented from further decomposition through controlling the oxygen partial pressure higher than 10 1.248 Pa in the pyrolysis of ammonium perrhenate. This result was further validated via DSC-TGA analysis of ammonium perrhenate. The typical rhenium powders prepared by the CVD method proposed show irregular polyhedron morphology with particle size in the range of 100-800 nm and a Ds0 of 308 nm. The specific surface area and oxygen content were measured to be 4.37 m^2/g and 0.45%, respectively.

奶粉中脂肪酸的气相色谱-质谱分析

To determine the fatty acids in milk powders,the fatty oils of milk powders were extracted by Rose-Gettlieb method,the fatty acids in the fatty oils were esterified by potassium hydroxide-methanol,and then analyzed by gas chromatography-mass spectrometry (GC-MS).The results indicate that main fatty acids’ carbon chain were from 8 to 24,each fatty acid has different conents in different samples and the content was determined by area normalization.

BONDING INTERFACE AND WEAR BEHAVIOR OF CBN GRAINS BRAZED USING NANO-TiC POWDER MODIFIED FILLER

A new kind of composite fillers,composed of Ag-Cu-Ti alloy and nano-TiC powders,is utilized to braze cubic boron nitride （CBN） grains and tool substrate. The bonding system,including the interfacial microstructure and reactive products between CBN grains and filler layer,is observed by optical microscope and scanning electron microscope （SEM）. Resistant-to-wear experiments of the brazed grains are performed. Results show that the nano-TiC powders evenly distribute in the filler layer so that the resultants grow compactly and uniformly on the surface of CBN grain. This indicates that the chemical bond is established between CBN grains and nano-TiC modified filler. Accordingly,the bonding strength of the grains is ensured. The CBN grains are worn smoothly without grain pull-out.

Enhanced photocatalytic properties of hierarchical nanostructured TiO_2 spheres synthesized with titanium powders

Using Ti powder as reagent, TiO 2 nanoneedle/nanoribbon spheres were prepared via hydrothermal method in NaOH solution. The samples were characterized by field emission scanning electron microscopy （FESEM）, transmission electron microscopy （TEM） with selected area electron diffraction （SAED）, X-ray diffraction （XRD）, and UV-visible light absorption spectrum. The results indicate that the growth orientations of the crystals are influenced by the hydrothermal temperature and NaOH concentration. The diameter of the nanoneedle spheres and nanoribbon spheres （40 50 μm） are almost the same as that of Ti powders. TiO 2 nanoneedle/nanoribbon sphere powders are anatase after heat treatment at 450 °C for 1 h. Furthermore, methyl orange was used as a target molecule to estimate the photocatalytic activity of the specimens. Under the same testing conditions, the photocatalytic activities of the products decrease in the following order： TiO 2 nanoneedle sphere, TiO 2 nanoribbon sphere and P25.

Application of pre-alloyed powders for diamond tools by ultrahigh pressure water atomization

Copper, iron and cobalt based pre-alloyed powders for diamond tools were prepared by ultrahigh pressure water atomization（UPWA） process. Pre-alloyed powders prepared by different processes including UPWA, conventional water atomization （CWA） and elemental metal mechanical mixing （EMMM） were sintered to segments and then compared in mechanical properties, holding force between matrix and diamond, fracture morphology of blank and sintering diamond section containing matrix. The results showed that the pre-alloyed powder prepared by UPWA exhibits the best mechanical properties including the relative density, the hardness and the bending strength of matrix sinteredsegment. Sintered segments fractography of UPWA pre-alloyed powder indicatesmechanical mosaic strength and chemical bonding force between the pre-alloyed powder and the diamond, leading to the great increase in the holding force between matrix and diamond. The mechanical performance andthe service life of diamond tools were greatly improved by UPWA pre-alloyed powders.

Synthesis of (Ca, Mg)-α′-Sialon-AlN-BN powders from boron-rich blast furnace slag by microwave carbothermal reduction-nitridation

(Ca, Mg)-α′-Sialon-AlN-BN powders were synthesized by the carbothermal reduction and nitridation (CRN) method using boron-rich slag, one of the intermediate products from pyrometallurgy separation of pageit, as the staring material. The influences of synthesis temperature and holding time on the phase composition and microstructure during the microwave CRN were studied by XRD, SEM and EDS. The comparison between two heating techniques, conventional and microwave heating, on the synthesized powder was presented as well. The experimental results revealed that the phase compositions and microstructures of the synthesized products were greatly affected by the synthesis temperature and holding time. With an increase in the synthesis temperature or holding time, the relative amount of α′-Sialon increased and α′-Sialon became the main crystalline phase at 1400 °C for 6 h. The synthesized products also contained AlN, BN and a small amount of β-SiC. Elongated α′-Sialon grains, short rod AlN grains, aggregate nanoscale BN grains were observed in the synthesized powders. The reaction temperature of microwave heating method was reduced by 80 °C, the reaction time was shortened by 2 h, and more elongated α′-Sialon grains with large aspect ratio were observed.

Rapid synthesis of Ti(C,N) powders by mechanical alloying and subsequent arc discharging

Ti（C,N） powders were synthesized by mechanical alloying （MA） from a mixture of pure titanium and graphite under a nitrogen atmosphere in a planetary mill.Effects of arc discharging on phase transformation and microstructure of MA powders milled for 1-7 h were explored.The results show that Ti（C,N） powders were prepared after mechanical milling for 1 h and subsequent arc discharge treatment,whereas the synthesis reaction did not occur in 7 h by mechanical milling alone.The ions produced during arc discharging interacted with powder particles and accelerated the diffusion of atoms and the nucleation on the surface of the as-milled powder,which results in fast synthesis of Ti（C,N） powders.The formation mechanisms of the two synthesis processes are self-propagating reactive synthesis.

Influence of high energy ball milling on Al-30Si powder and ceramic particulate

The influence of high energy ball milling on Al 30Si powder and ceramic particulate SiC was studied by means of SEM, XRD and DSC. The results show that Al 30Si powder and their microstructure are obviously refined after high energy ball milling process. The alloy powder and SiC p stick closely to each other without interfacial reaction. DSC results detect no reaction but relaxation of the samples. So high energy ball milling can be used as an effective method for ceramic particulate pre treatment in the fabrication of MMC.

Measurement and Influence Factors of the Flowability of Microcapsules with High-content β-Carotene

The flowability of five kinds of microencapsulation powders,with differentβ-carotene contents and by two alternative particle-forming technologies i.e.spray-drying and starch-catching beadlet technology,was meas- ured.The actual flow properties of the five powders were compared based on bin-flow test,and three flow indexes (Hausner ratio,repose angle and flow index)were measured.It was found that the repose angle is the most suitable index to reflect the flowability of these powders for the particle properties would not be altered due to compaction or tapping during the measuring process.Particle size and particle size distribution play most important roles in the flowability of these granular materials,which was also influenced by other factors like shape,surface texture,sur- face roughness,etc.Microcapsules with wall material of gelatin and a layer of modified starch absorbed on the sur- face showed excellent flowabilities and good mechanical properties,and they are favorable for tabletting to supply β-carotene.

Influence of cerium ions on the anatase-rutile phase transition of TiO_2 prepared by sol-gel auto-igniting synthesis

The anatase-rutile phase transformation of TiO_2 doped cerium up to 5 molpercent was studied by X-ray diffraction and X-ray photoelectron spectroscopy. The samples wereprepared by sol-gel auto-igniting synthesis process from a TiO(NO_3)_2-Ce(NO_3)_2-NH_4NO_3-citricacid complex compound system. The combusted amorphous powders were calcined at differenttemperatures. Significant structural changes were observed during the various stages of the phasetransformation. It was concluded that at low dopant contents, cerium ions were incorporated into theTiO_2 structure, and the anatase phase was stabilized; but at larger amounts, part of the dopantwas segregated on the surface of TiO_2 and the rutile formation was accelerated at elevatedcalcination temperature.

Impact mechanism of gas temperature in metal powder production via gas atomization

This paper aims at studying the influence mechanism of gas temperatures(300 K,400 K,500 K,and 600 K)on gas atomization by simulating the integral atomization process of the close-coupled nozzle in vacuum induction gas atomization(VIGA).The primary atomization is simulated by the volume of fluid(VOF)approach,and the second atomization is studied by the discrete phase model(DPM)combined with the instability breakage model.The results show that,at an increased gas temperature,the influences of gas-liquid contact angle and gas temperature in the recirculation zone on the primary atomization are virtually negligible.However,increasing the gas temperature will increase the gas-liquid relative velocity near the recirculation zone and decrease the melt film thickness,which are the main reasons for the reduced mass median diameter(MMD,d50)of primary atomized droplets.During the secondary atomization,increasing the gas temperature from 300 K to 600 K results in an increase in the droplet dispersion angle,which is beneficial to the formation of spherical metal powder.In addition,increasing the gas temperature,the positive effect of gas-liquid relative velocity increase on droplets refinement overweighs the negative influence of the GMR decrease,resulting in the reduced MMD and diameter distribution interval.From the analysis of the atomization mechanism,the increase in atomization efficiency caused by increasing the temperature of the atomizing gas,including primary atomization and secondary atomization,is mainly due to the increase in the gas drag force difference between the inner and outer sides of the annular liquid film.

Recovery of waste rare earth fluorescent powders by two steps acid leaching

The effects of the acid leaching and alkali fusion on the leaching efficiency of Y,Eu,Ce,and Tb from the waste rare earth fluorescent powders were investigated in this paper.The results show that hydrochloric acid is better than sulfuric acid in the first acid leaching,and NaOH is better than Na2CO3in the alkali fusion.In the first acid leaching,the Wloss is 20.94%when the waste rare earth fluorescent powders are acid leached in H?concentration 3 mol L-1and S/L ratio 1:3 for 4 h due to red powders dissolved.The better results of the alkali fusion can be got at 800℃ for 2 h when the NaOH is used.The blue powders and the green powders can be dissolved into NaAlO2and oxides such as rare earth oxide(REO).The REO can be dissolved in H?concentration 5 mol L-1,S/L1:10 for 3 h in the second acid leaching.The leaching rates of the Y,Eu,Ce,and Tb are 99.06%,97.38%,98.22%,and 98.15%,respectively.The leaching rate of the total rare earth is 98.60%.

Silicon assistant carbothermal reduction for SiC powders

The silicon assistant method to increase the reaction yield of carbothermal reduction of silica at a lower temperature is reported. The effect of silicon on the carbothermal reduction process has been investigated in detail. Compared with traditional reduction, the introduction of silicon can change the reaction path and further increase the conversion of silicon carbide at a lower temperature. It is considered that the assistant reduction consists of three steps： vaporizing and melting of silicon, formation of silicon monoxide, and synthesis of silicon carbide. The morphology of the synthesized SiC powders through the silicon assistant method can be affected apparently by the experimental temperature.

Preparation of electrolytic copper powders with high current efficiency enhanced by super gravity field and its mechanism

Super gravity field was employed to enhance electrolytic reaction for the preparation of copper powders.The morphology, microstructure and size of copper powders were characterized by scanning electron microscopy,X-ray diffractometry and laser particle analysis.The results indicated that current efficiencies of electrolytic copper powders under super gravity field increased by more than 20% compared with that under normal gravity condition.Cell voltage under super gravity field was also much lower.The size of copper powders decreased with the increase of gravity coefficient(G).The increase of current efficiency can be contributed to the disturbance of electrode/electrolyte interface and enhanced mass transfer of Cu2+ in super gravity field.Meanwhile,the huge gravity acceleration would promote the detachment of copper powders from electrode surface during electrolytic process,which can prevent the growth of copper powders.

Preparation of high emissivity NiCr_2O_4 powders with a spinel structure by spray drying

Spray-drying was used to produce the high emissivity NiCr2O4 powders with a spinel structure. Preliminary investigations focused on fabricating the high emissivity powders for infrared radiation coatings and finding the relationship between microstructure and emissivity. The NiCr2O4 powders were characterized for composition, microstructure, and infrared emissivity by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, infrared radiant instrument, and Fourier transform infrared spectra （FT-IR）. Thermogravimetry and differential thermal analysis show that the appropriate baking temperature for NiCr2O4 powder preparation is about 1200？C. The emissivity measurement and FT-IR spectra show that, because of the special spinel structure, the NiCr2O4 powders have a high emissivity about 0.91. Spray-drying is a suitable method to produce the high emissivity ceramic powders.

PRODUCTION METHODS AND APPLICATIONS FOR HIGH-QUALITY METAL POWDERS AND SPRAYFORMED PRODUCTS

Metal powders of superlative quality, i.e. high cleanliness, rapidly solidified and spherical shape, have seen an increasing demand in the market. The leading technology for the production of such powders is the inert gas atomization of metal alloy melts. To fulfill these requirements, the metal alloy is usually produced in a vacuum induction melting furnace (VI-GA = vacuum induction melting/gas atomization) and poured by means of a preheated tundish system into a gas nozzle where the metal stream is disintegrated by a high kinetic energy inert gas jet. The produced micro-droplets solidify in a free fall inside the atomization tower. For special applications, super-clean and ceramic-free metal powders can be produced by using the EIGA (electrode induction melting/gas atomization) melting- and atomizing system. As an alternative to the metal powder route, the sprayforming technology allows to produce semi-finished products in one step. In this case, the metal droplets produced by the high-energy inert gas nozzle system are directly solidified on a substrate, allowing to form billets, rolls and tubes.