Optimizing the power conversion processes in diluted donor/acceptor heterojunctions towards 19.4%efficiency all-polymer solar cells

All polymer solar cells(all-PSCs)promise mechanically-flexible and morphologically-stable organic photovoltaics and have aroused increased interests very recently.However,due to their disorderly conformation structures within the photoactive film,inefficient charge generation and carrier transport are observed which lead to inferior photovoltaic performance compared to smaller molecular acceptor-based photovoltaics.Here,by diluting PM6 with a cutting-edge polymeric acceptor PY-IT and diluting PY-IT with PM6 or D18,donor-dominating or acceptor-dominating heterojunctions were prepared.Synchrotron X-ray and multiple spectrometer techniques reveal that the diluted heterojunctions receive increased structural order,translating to enhanced carrier mobility,improved exciton diffusion length,and suppressed non-radiative recombination loss during the power conversion.As the results,the corresponding PM6+1%PY-IT/PY-IT+1%D18 and PM6+1%PY-IT/PY-IT+1%PM6 devices fabricated by layer-by-layer deposition received superior power conversion efficiency(PCE)of 19.4%and 18.8%respectively,along with enhanced operational lifetimes in air,outperforming the PCE of 17.5%in the PM6/PY-IT reference device.

Cascade utilization of full spectrum solar energy for achieving simultaneous hydrogen production and all-day thermoelectric conversion

Solar-driven photocatalytic water/seawater splitting holds great potential for green hydrogen production.However,the practical application is hindered by the relatively low conversion efficiency resulting from the inadequate utilization of solar spectrum with significant waste in the form of heat.Moreover,current equipment struggles to maintain all-day operation subjected to the lack of light during nighttime.Herein,a novel hybrid system integrating photothermal catalytic(PTC)reactor,thermoelectric generator(TEG),and phase change materials(PCM)was proposed and designed(named as PTC-TEG-PCM)to address these challenges and enable simultaneous overall seawater splitting and 24-hour power generation.The PTC system effectively maintains in an optimal temperature range to maximize photothermal-assisted photocatalytic hydrogen production.The TEG component recycles the low-grade waste heat for power generation,complementing the shortcoming of photocatalytic conversion and achieving cascade utilization of full-spectrum solar energy.Furthermore,exceptional thermal storage capability of PCM allow for the conversion of released heat into electricity during nighttime,contributing significantly to the overall power output and enabling PTC-TEG-PCM to operate for more than 12 h under the actual condition.Compared to traditional PTC system,the overall energy conversion efficiency of the PTC-TEG-PCM system can be increased by∼500%,while maintaining the solar-to-hydrogen efficiency.The advancement of this novel system demonstrated that recycling waste heat from the PTC system and utilizing heat absorption/release capability of PCM for thermoelectric application are effective strategies to improve solar energy conversion.With flexible parameter designing,PTC-TEG-PCM can be applied in various scenarios,offering high efficiency,stability,and sustainability.

Application of Power Electronics Converters in Renewable Energy

Against the backdrop of global energy shortages and increasingly severe environmental pollution,renewable energy is gradually becoming a significant direction for future energy development.Power electronics converters,as the core technology for energy conversion and control,play a crucial role in enhancing the efficiency and stability of renewable energy systems.This paper explores the basic principles and functions of power electronics converters and their specific applications in photovoltaic power generation,wind power generation,and energy storage systems.Additionally,it analyzes the current innovations in high-efficiency energy conversion,multilevel conversion technology,and the application of new materials and devices.By studying these technologies,the aim is to promote the widespread application of power electronics converters in renewable energy systems and provide theoretical and technical support for achieving sustainable energy development.

储能电站级联式PCS故障类型解析及智能溯源

储能电站能有效解决清洁能源的不稳定性和不可预测性。随着电化学储能电站的推广应用,其工程应用技术已完善,但在调试自动化和智能运检等高级应用方面还有较大的研究空间。此处针对级联H桥功率转换系统(PCS)核心部件的不同技术特性,将PCS的故障按发生对象进行组别分类,提取并解析各类故障暂态过程中的告警、保护信息,以及具体的暂态故障录波数据特征,多维度、全环节穷举出各类故障可能的起因,通过构建典型故障类型数据库实现PCS的故障智能溯源。

储能PCS叠层母线研究

该研究以储能变流器(PCS)叠层母排就如何降低电感为研究对象,进行了PCS及电感原理、叠层母排导体及绝缘材料选型介绍。通过电容端子排布、电容端子间距、IGBT是否偏心、母排层数等因素对电感的影响进行仿真研究。最后,对叠层母排及组装成子模块进行电气测试。结果表明:电容端纵向布置,N极靠内,电容引脚间距减小,IGBT居中布置且将3层极板改为2层极板,N极板与负极板分布在同一层,电感最优,为5.13 nH,电感降低29%。叠层母排局放测试,局放值为0.1 pC(1 kV,AC)。直流耐压测试,漏电流为0 mA(3 kV,DC)。叠层母排测试电感为5.3 nH,与仿真值保持一致。子模块测试电感为15.06 nH,满足要求。

Low Power Polarity Conversion Based on the Whole Annealing Genetic Algorithm

For an n-variable logic function,the power dissipation and area of the REED-MULLER （RM） circuit corresponding to each polarity are different. Based on the propagation algorithm of signal probability,the decomposition algorithm of a multi-input XOR/AND gate,and the multiple segment algorithm of polarity conversion,this paper successfully applies the whole annealing genetic algorithm （WAGA） to find the best polarity of an RM circuit. Through testing eight large-scale circuits from the Microelectronics Center North Carolina （MCNC） Benchmark, the SYNOPSYS synthesis results show that the RM circuits corresponding to the best polarity found using the proposed algorithm attain average power,area,and max delay savings of 77.2% ,62.4% ,and 9.2% respectively,compared with those under polarity 0.

Research on Energy Conversion System of Floating Wave Energy Converter

A wave power device includes an energy harvesting system and a power take-off system. The power take-off system of a floating wave energy device is the key that converts wave energy into other forms. A set of hydraulic power take-off system, which suits for the floating wave energy devices, includes hydraulic system and power generation system. The hydraulic control system uses a special“self-hydraulic control system”to control hydraulic system to release or save energy under the maximum and the minimum pressures. The maximum pressure is enhanced to 23 MPa, the minimum to 9 MPa. Quite a few experiments show that the recent hydraulic system is evidently improved in efficiency and reliability than our previous one, that is expected to be great significant in the research and development of our prototype about wave energy conversion.

Advanced Power Module Packaging and Integration Structures for High Frequency Power Conversion：From Silicon to GaN

The emerging of commercial high-voltage gallium nitride(GaN) power devices provides extraordinary switching performance over silicone devices, which enables high-voltage power conversion switching at megahertz range.Such outstanding features also pose strong challenges for device packaging design since the package parasitics can significantly influence the device switching characteristics, and thus can shadow the advantages brought by GaN devices. Designers have been dealing with these challenges brought by high du/dt and high-frequency switching operation even since the silicon(Si) era when fast switching Si MOSFET is first developed and came up with lots of inspiring advanced power module packaging structures to mitigate the problems.This paper presents a review of advanced power module packaging and integration structures that are suitable for high frequency power conversion.The review covers the heritage from the high frequency Si MOSFET packaging to the state-of-the-art for GaN devices.

Regulation of Power Conversion in Fuel Cells

Here we report a regulation about power conversion in fuel cells. This regulation is expressed as that total power produced by fuel cells is always proportional to the square of the potential difference between the \{equilibrium\} potential and work potential. With this regulation we deduced fuel cell performance equation which can describe the potential vs.the current performance curves, namely, polarization curves of fuel cells with three power source parameters: equilibrium potential E_0; internal resistance R; and power conversion coefficient K. The concept of the power conversion coefficient is a new criterion to evaluate and compare the characteristics and capacity of different fuel cells. The calculated values obtained with this equation agree with practical performance of different types of fuel cells.

Optimal oxide-aperture for improving the power conversion efficiency of VCSEL arrays

The maximum power conversion efficiencies of the top-emitting,oxide-confined,two-dimensional integrated 2×2 and4×4 vertical-cavity surface-emitting laser（VCSEL） arrays with the oxide-apertures of 6 μm,16 μm,19 μm,26 μm,29 μm,36 μm,39 μm,and 46 urn are fabricated and characterized,respectively.The maximum power conversion efficiencies increase rapidly with the augment of oxide-aperture at the beginning and then decrease slowly.A maximum value of27.91%at an oxide-aperture of 18.6 μm is achieved by simulation.The experimental data are well consistent with the simulation results,which are analyzed by utilizing an empirical model.

Direct driven wind energy conversion system based on hybrid excitation synchronous machine

A novel direct-drive type wind power generation system based on hybrid excitation synchronous machine（HESM）is introduced in this paper.The generator is connected to an uncontrollable rectifier,and a fully controlled voltage-sourceinverter is used to connect the system to utility grid.An intermediate DC bus exists between the rectifier and inverter.A new control strategy is proposed which achieves the maximum power point tracking（MPPT） with the control of excitation current of HESM and stabilizes the DC link voltage with the control of inverter output current simultaneously.Specially-designed buck circuit is used to control the excitation current of HESM,and grid voltage-oriented vector control strategy is employed to realize the decoupling of the inverter output power.Simulation results and experiment in 3 kW lab prototype show an excellent static and dynamic performance of the proposed system.

OUTPUT MAXIMIZATION CONTROL FOR VSCF WIND ENERGY CONVERSION SYSTEM USING EXTREMUM CONTROL STRATEGY

The energy conversion optimization control strategy is presented for a family of horizontal-axis variablespeed fixed-pitch wind energy conversion systems,working in the partial load region.The system uses a variablespeed wind turbine(VSWT)driving a squirrel-cage induction generator(SCIG)connected to a grid.A new maximum power point tracking(MPPT)approach is proposed based on the extremum seeking control principles under the assumption that the wind turbine model and its parameters are poorly known.The aim is to drive the average position of the operation point close to optimality.Here the wind turbulence is used as search disturbance instead of inducing new sinusoidal search signals.The discrete Fourier transform(DFT)process of some available measures estimates the distance of operation point to optimality.The effectiveness of the proposed MPPT approach is validated under different operation conditions by numerical simulations in MATLAB/SIMULINK.The simulation results prove that the new approach can effectively suppress the vibration of system and enhance the dynamic performance of system.

基于PCS变主从协同控制的微电网平滑离网技术

当微电网由并网模式进入离网模式时,储能变流器和光伏逆变器采用传统控制方式可能会造成微电网系统振荡、储能系统过充和过放的问题。采用储能变流器和光伏逆变器并联运行的微电网结构,通过分析微电网各电源出力情况,提出一种在微电网离网时刻,考虑储能系统荷电状态(State of charge,SOC)的变主从协同控制策略,即将主从控制、对等控制、分层控制的优势结合起来,实现储能变流器在二次调压调频的下垂控制和PQ控制间灵活切换,实现微电网的平滑离网,防止储能系统过充和过放。最后搭建仿真模型,对所提方法的有效性进行验证。

Highly Efficient Power Conversion from Salinity Gradients with Ion-Selective Polymeric Nanopores

A polymeric nanopore membrane with selective ionic transport has been proposed as a potential device to convert the chemical potential energy in salinity gradients to electrical power. However, its energy conversion efficiency and power density are often limited due to the challenge in reliably controlling the size of the nanopores with the conventional chemical etching method. Here we report that without chemical etching, polyimide （PI） membranes irradiated with GeV heavy ions have negatively charged nanopores, showing nearly perfect selectivity for cations over anions, and they can generate electrical power from salinity gradients. We further demonstrate that the power generation efficiency of the PI membrane approaches the theoretical limit, and the maximum power density reaches 130m W/m2 with a modified etching method, outperforming the previous energy conversion device that was made of polymeric nanopore membranes.

Power control scheme for multiple antenna systems with space-time coding in Rayleigh fading channels

Two optimal power control （PC） schemes under the power constraint for space-time coded multiple input multiple output systems over the flat Rayleigh fading channel with the imperfect channel state information （CSI） are presented. One is based on the minimization of a bit error rate （BER）, and the other is based on the maximization of a fuzzy signal-to-noise ratio. In these schemes, different powers are allocated to individual transmit an- tennas rather than equal power in the conventional one. For the first scheme, the optimal PC procedure is developed. It is shown that the Lagrange multiplier for the constrained optimization in the power control does exist and is unique. A practical iterative algorithm based on Newton＇s method for finding the Lagrange multiplier is proposed. In the second scheme, some existing schemes are included, and a suboptimal PC procedure is developed by means of the asymptotic performance analysis. With this suboptimal scheme, a simple PC calculation formula is provided, and thus the calculation of the PC will be straightforward. Moreover, the suboptimal scheme has the BER performance close to the optimal scheme. Simulation results show that the two PC schemes can provide BER lower than the equal PC and antenna selection scheme under the imperfect CSI.

Power Allocation for Wireless Powered MIMO Transmissions with Non-Linear RF Energy Conversion Models

We study a radio frequency(RF) wireless energy transfer(WET) enabled multiple input multiple output(MIMO) system. A time slotted transmission pattern is considered. Each slot can be divided into two phases, downlink(DL) WET and uplink(UL) wireless information transmission(WIT). Since energy conversion efficiency of the energy harvesting circuits are non.linear, the conventional linear model leads to a mismatch for resource allocation. In this paper, the power allocation algorithm considering the practical non.linear energy harvesting circuits is studied. The optimization problem is formulated to maximize the energy efficiency of system with multiple constraints, i.e., the transmission power, the received power and the minimum harvested energy, which is a non.convex problem. We transform the objective function from fractional form into an equivalent objective function in subtractive form and provide an iterative power allocation algorithm to achieve the optimal solution. Numerical results show that our proposed algorithm with the non.linear RF energy conversion models can achieve much better performance than the algorithm with the conventional linear model.

Three-Dimensional Study of the Effect of the Angle of Incidence of a Magnetic Field on the Electrical Power and Conversion Efficiency of a Polycrystalline Silicon Solar Cell under Multispectral Illumination

A three-dimensional approach to the effect of magnetic field incidence angle on electrical power and conversion efficiency is performed on a front-illuminated polycrystalline silicon bifacial solar cell. A solution of the continuity equation allowed us to present the equations of photocurrent density, photovoltage and electric power. The influence of the angle of incidence of the magnetic field on the photocurrent density, the photovoltage and the electric power has been studied. The curves of electrical power versus dynamic junction velocity were used to extract the values of maximum electrical power and dynamic junction velocity and to calculate those of conversion efficiency. From this study, it is found that the conversion efficiency values increase with the angle of incidence of the magnetic field.

STABILIZATION EFFECT OF MULTI-MACHINE POWER SYSTEM BY USING ADJUSTA BLE SPEED GENERATOR

This paper describes a stabilization effect after installating an adjustable speed generator (ASG) in a multi machine power system. A personal computer based ASG module has been de veloped for the simulations in parallel with the analog power system simulator i n the Research Laboratory of the Kyushu Electric Power Co. The three phase ins t antaneous value based ASG model has been developed in the Matlab/Simulink envir onment for its detailed and real time simulations, which have been performed on a digital signal processor (DSP) board with AD and DA conversion interfaces inst alled in a personal computer (PC). Simulational results indicate the hig hly improved overall stability of the multi machine power system after installa ting the ASG.

Proposal of New PCCS Method for PCS in a PV Generation System

This paper proposes a new peak current control switching(PCCS)method for single-phase inverter in photovoltaic(PV)generation system.This method minimizes the difference between a peak current and the current command with a constant switching frequency.In this paper,the principle and the simulation results of the proposed method are described.In this paper,the principle and the simulated transient characteristics of this PCCS method are described.From the results,it is clarified that the proposed switching method is effective.

Study on Purchasing Power Conversion Coefficient at Par

The basic theory of the purchasing power at par refers to the rate of one country＇s currency to U.S. dollar while purchasing ＂a basket＂ goods and services in the same quantity and quality respectively in this country and U.S.A. This paper gives out calculation method of purchasing power conversion coefficient at par and how to calculate the non-base year purchasing power at par.