Open-circuit Fault-tolerant Control Strategy Based on Five-level Power Converter for SRM System

Switched reluctance motor power converters are prone to open-circuit faults because it need to withstand large voltages and currents.Due to the small number of traditional asymmetrical half bridge topology switches,it is difficult to carry out fault tolerant control when power converters has an open-circuit fault,resulting in larger output torque ripple.This paper presents a five-level power converter based on the traditional asymmetric half-bridge power converter.The five-level topology has more switching states and can work in multi-level mode.Based on the topology,different excitation and demagnetization voltages can be choose at different speeds.A fault-tolerance strategy is developed to decrease the influence of the open-circuit fault.The five-level power converter has four switches per phase,and two of them will be used in one of the operating mode.So the remaining two of the switches can be used for safe backup,enabling fault-tolerant control when an open-circuit occur.Since each phase of the five-level power converter proposed in this paper is independent of each other,a reasonable control strategy can be used to avoid the unbalance of the midpoint potential.Finally,the topology and fault-tolerant strategy proposed in this paper are verified by simulation and experiment.

1064 nm InGaAsP multi-junction laser power converters

Laser photovoltaic devices converting 1064 nm light energy into electric energy present a promising prospect in wireless energy transmission due to the commercial availability of high power 1064 nm lasers with very small divergence. Besides their high conversion efficiency, a high output voltage is also expected in a laser energy transmission system. Meanwhile,1064 nm InGaAsP multi-junction laser power converters have been developed using p^+-InGaAs/n^+-InGaAs tunnel junctions to connect sub-cells in series to obtain a high output voltage. The triple-junction laser power converter structures are grown on p-type InP substrates by metal-organic chemical vapor deposition(MOCVD), and InGaAsP laser power converters are fabricated by conventional photovoltaic device processing. The room-temperature I–V measurements show that the 1 × 1 cm^2 triplejunction InGaAsP laser power converters demonstrate a conversion efficiency of 32.6% at a power density of 1.1 W/cm^2, with an open-circuit voltage of 2.16 V and a fill factor of 0.74. In this paper, the characteristics of the laser power converters are analyzed and ways to improve the conversion efficiency are discussed.

Finite Control Set Model Predictive Control with Feedback Correction for Power Converters

As an open-loop model predictive control algorithm,finite control set model predictive control(FCS-MPC)scheme in power converter system is based on assumption that responses of optimal control implemented on prediction model agree well with actual system.The influence of model parameter mismatches and environment disturbance on control performance of scheme is neglected.Then,based on feedback correction strategy in traditional model predictive control algorithm,we derive a finite control set model predictive control with feedback correction scheme(FCS-MPCFC)that allows us to adjust prediction model output at current instant by model prediction error at previous instant,and the closed-loop correction of prediction model output is achieved.Simulations comparison analyses on a two-level three-phase inverter with multi-type model parameter mismatches controlled by traditional and improved FCS-MPC scheme are presented.Experiments are carried out on DSP controller platform.

Energy band adjustment of 808 nm GaAs laser power converters via gradient doping

The gradient doping regions were employed in the emitter layer and the base layer of GaAs based laser power converters(LPCs).Silvaco TCAD was used to numerically simulate the linear gradient doping and exponential gradient doping structure,and analyze the transport process of photogenerated carriers.Energy band adjustment via gradient doping improved the separation and transport efficiency of photogenerated carriers and reduced the total recombination rate of GaAs LPCs.Compared with traditional structure of LPCs,the photoelectric conversion efficiency of LPCs with linear and exponential gradient doping structure were improved from 52.7%to 57.2%and 57.7%,respectively,under 808 nm laser light at the power density of 1 W/cm^(2).

Exact Dynamic Modeling of PWM DC-to-DC Power Converters—Part I: Continuous Conduction Mode

A general approach is presented by which the exact frequency response of any transfer function of switched linear networks can be determined. This is achieved with a describing function approach using a state space equation formulation. This work presents a somewhat simplified set of equations to one previously given by one of the authors. To demonstrate application of the general formulation, the frequency responses of switched networks used as PWM DC-to-DC converters operating in continuous conduction mode (CCM) under voltage mode control are derived. (The accompanying paper, Part II, will present results for converters operating in discontinuous conduction mode (DCM)). From the general sets of equations developed here, both the control to output and input source variation to output frequency responses are derived. The describing function approach enables exact frequency response determination, even at high frequencies where the accuracy using average models may be compromised. Confirmation of the accuracy of the derived models is provided by comparing the responses with those obtained using the commercial simulator PSIM on a PWM boost converter. The magnitude and phase responses are shown to match perfectly over the full range of frequencies up to close to half the switching frequency. Matlab code that implements the models is given such that the user can easily adapt for use with other PWM converter topologies.

Exact Dynamic Modeling of PWM DC-to-DC Power Converters—Part II: Discontinuous Conduction Mode

This paper follows on from the first paper, Part I, where a general formulation of a describing function approach to frequency response determination of switched linear networks, such as PWM converters, was simplified and updated. The models assume a piecewise linear state space equation description of the system and results in a closed form solution for the sought after frequency response. In Part I, model derivation was demonstrated for the case of PWM converters operating in the continuous conduction mode (CCM). This operating mode does not feature any state dependent switching times. In this paper, Part II, frequency response models for any transfer function for PWM converters operating in discontinuous conduction mode (DCM) are derived based on the theory presented in Part I. This operating model features state dependent switching times. The describing function models developed are exact and therefore, in terms of accuracy, are to be preferred over averaged models which are widely used. The example of a boost dc-to-dc converter operating in DCM is simulated to obtain the control to output and input to output frequency responses and are compared with the models derived here. Excellent agreement between the simulated and model responses was found. Matlab code implementing the analytical models is also presented which the user can adapt for any other PWM converter topology. The models derived here may be used as a basis from which simplified models may be derived while still preserving required accuracy.

A Novel Serial Hybrid Three-level NPC Topology for Multi-MW Medium Voltage Wind Power Converters

提出一种新型的串联混合三电平中点钳位（neutralpoint clamped,NPC）拓扑,该拓扑是基于传统三电平NPC拓扑的改进和优化,引入大功率IGBT的串联应用。该新型拓扑中,桥臂的两个外管分别用两个低压IGBT串联,两个内管均用高压IGBT。在多兆瓦级中压风电变流器中,大功率IGBT的开关损耗很大,从而限制了开关频率。提出的新型拓扑通过低压IGBT的串联来减小功率器件的损耗,从而提高开关频率,同时可减小输出滤波器的尺寸。通过传统三电平拓扑和新型串联混合三电平拓扑IGBT损耗的对比,说明新拓扑的优势。通过改变门极驱动电阻实现串联IGBT的均压,对新拓扑的应用具有重大意义。最后通过新拓扑的单相样机验证新拓扑的正确性和可行性。

Harmonic Analysis of Hoist Drive System FED by Power Converter and Cycloconverter

There are a lot of large capacity nonlinear loads in power systems in coal mine, such as, hoist supply system fed by power converter and cycloconverter. The harmonics generated by those nonlinear loads are very serious. The model for harmonic analysis of power electronic converter and cycloconverter is established, and a novel method for harmonic analysis is proposed in this paper. The suggested method has advantages of less memory capacity need, fast estimation and high accuracy. The comput-ing results are good agreed with the measuring results. The suggested method is much useful for the harmonic prediction of power system in coal mine.

Loop-Shaping Based Control for Switch Mode DC-DC Power Converters

Renewable energy sources require switching regulators as an interface to a load with high efficiency, small size, proper output regulation, and fast transient response. Moreover, due to the nonlinear behavior and switching nature of DC-DC power electronic converters, there is a need for high-performance control strategies. This work summarized the dynamic behavior for the three basic switch-mode DC-DC power converters operating in continuous conduction mode, i.e. buck, boost, and buck-boost. A controller was designed using loop-shaping based on current-mode control that consists of two feedback loops. A high-gain compensator with wide bandwidth was used in the inner current loop for fast transient response. A proportional-integral controller was used in the outer voltage loop for regulation purposes. A procedure was proposed for the parameters of the controller that ensures closed-loop stability and output voltage regulation. The design-oriented analysis was applied to the three basic switch-mode DC-DC power converters. Experimental results were obtained for a switching regulator with a boost converter of 150 W, which exhibits non-minimum phase behavior. The performance of the controller was tested for voltage regulation by applying large load changes.

A New Type Power Converter and Its Application Prospect in Industry

A new type power convertsion mode is structured by combineing switch power conversion mode with linear amplifica-tion mode, so as to acquire their integrated optimal performances. The theoretical analyses and experimental results are presented in this paper. They are proved that the new type converter can match many kinds of loads, including nonlinear loads, with strong robustness, good waveforms and high efficiency. Its application prospect in industry can be expected, particularly for the conditions where serious static and dynamic performances are required.

An Investigation of Power Converters Fed BLDC Motor for Adjustable Speed

This paper reports the converter topologies which are employed for better Power Factor Correction at the input side. The Power Factor Correction is an important factor when considering the Power Quality. Based on the converter topologies, the Bridgeless converters are preferred in order to reduce the number of switching devices, losses associated with it and improve the Power Quality further more. This paper investigates about the Power Factor performances and conduction losses of the Bridgeless Power Factor Corrector Converters which see through the benefits and limitations by analyzing the Bridgeless Buck-Boost Converter, Bridgeless SEPIC converter and Bridgeless CUK converter. The resultant voltage is fed to the BLDC motor which is rapidly replacing the Induction motor for its better operating characteristics. These strategies are being analyzed using the MATLAB/Simulink software and the results are verified through the experimental analysis. The converter choice is preferred through the performance characteristics and Power Factor Correction at the supply. The Power Factor obtained should be within the acceptable limits under IEC 61000-3-2 standards.

Implementation of a Higher Quality dc Power Converter

Many single and three-phase converters are well developed, and covered up in most of electric markets. It is used in many applications in power systems and machine drives. However, an exact definite output signal from the dc side still not recognized. The waveforms of output voltage and current demonstrate an imperfect dc signal and constitute losses, harmonic distortion, low power factor, and observed some ripples. An approximately perfect rectifier bridge is the aim of this research. Perhaps it gives the ability to identify the parameters of the converter to obtain, as much as possible, a perfect dc signal with less ripple, high power factor and high efficiency. Design is implemented by simulation on Power Simulator PSIM, and practically, a series regulator LM723 is applied to provide regulating output voltage. Comparisons of both simulation and hardware results are made to observe differences and similarities.

Generic Modeling and Control Framework for Power Systems Dominated by Power Converters Connected Through a Passive Transmission and Distribution Grid

In this paper,a compact mathematical model having an elegant structure,together with a generic control framework,are proposed for generic power systems dominated by power converters that are interconnected through a passive transmission and distribution(T&D)grid,by adopting the port-Hamiltonian(pH)systems theory and the fundamental circuit theory.The models of generic T&D lines are developed and then the model of a generic T&D grid is established.With the proposed control framework,the controlled converters are proven to be passive and Input-to-State Stable(ISS).The compact mathematical model is scalable and can be applied to power systems with multiple power electronic converters with generic passive controllers,passive local loads,and different types of passive T&D lines connected in a meshed configuration without self-loops,so it is very generic.Moreover,the resulting power system is proven to be ISS as well.The analysis is carried out without assumptions on constant frequency/voltage,constant loads,and/or lossless networks,except the need of passivity for all parts involved,and without using the Clarke/Park transformations or the graph theory.To simplify the presentation,three-phase balanced systems are adopted but the results can be easily adapted for single-phase or unbalanced three-phase systems.

Application of Power Electronics Converters in Renewable Energy

Against the backdrop of global energy shortages and increasingly severe environmental pollution,renewable energy is gradually becoming a significant direction for future energy development.Power electronics converters,as the core technology for energy conversion and control,play a crucial role in enhancing the efficiency and stability of renewable energy systems.This paper explores the basic principles and functions of power electronics converters and their specific applications in photovoltaic power generation,wind power generation,and energy storage systems.Additionally,it analyzes the current innovations in high-efficiency energy conversion,multilevel conversion technology,and the application of new materials and devices.By studying these technologies,the aim is to promote the widespread application of power electronics converters in renewable energy systems and provide theoretical and technical support for achieving sustainable energy development.

Inertia response from full-power converter-based permanent magnet wind generators

With a high penetration of wind turbines,the proportion of synchronous generation in the power system will be reduced at times,thus creating operating difficulties especially during frequency events.Therefore,it is anticipated that many grid operators will demand inertia response from wind turbines.In this article,different ways for emulating inertia response in full-rated power converter-based wind turbines equipped with permanent magnet synchronous generators are considered.Supplementary control signals are added to the controller of the wind turbine to extract stored energy from the rotating mass and DC-link capacitors.Simulations in MATLAB/Simulink show that the inertia response is improved by adding a term proportional to the rate of change of frequency and by extracting the stored energy in the DC-link capacitors.

Stability of interacting grid-connected power converters

The power grid in a typical micro distribution system is non-ideal,presenting itself as a voltage source with significant impedance.Thus,grid-connected converters interact with each other via the non-ideal grid.In this study,we consider the practical scenario of voltage-source converters connected to a three-phase voltage source with significant impedance.We show that stability can be compromised in the interacting converters.Specifically,the stable operating regions in selected parameter space may be reduced when grid-connected converters interact under certain conditions.In this paper,we develop bifurcation boundaries in the parameter space with respect to Hopftype instability.A small-signal model in the dq-frame is adopted to analyze the system using an impedance-based approach.Moreover,results are presented in design-oriented forms so as to facilitate the identification of variation trends of the parameter ranges that guarantee stable operation.

Robust Nonlinear Current Sensorless Control of the Boost Converter with Constant Power Load

The boost converter feeding a constant power load (CPL) is a non-minimum phase system that is prone to the destabilizing effects of the negative incremental resistance of the CPL and presents a major challenge in the design of stabilizing controllers. A PWM-based current-sensorless robust sliding mode controller is developed that requires only the measurement of the output voltage. An extended state observer is developed to estimate a lumped uncertainty signal that comprises the uncertain load power and the input voltage, the converter parasitics, the component uncertainties and the estimation of the derivative of the output voltage needed in the implementation of the controller. A linear sliding surface is used to derive the controller, which is simple in its design and yet exhibits excellent features in terms of robustness to external disturbances, parameter uncertainties, and parasitics despite the absence of the inductor’s current feedback. The robustness of the controller is validated by computer simulations.

Analysis and control of wind-driven self-excited induction generators connected to the grid through power converters

The analysis of the wind-driven self-excited induction generators （SEIGs） connected to the grid through power converters has been developed in this paper. For this analysis, a method of representing the grid power as equivalent load resistance in the steady-state equivalent circuit of SEIG has been formulated. The technique of genetic algorithm （GA） has been adopted for making the analysis of the proposed system simple and straightfor- ward. The control of SEIG is attempted by connecting an uncontrolled diode bridge rectifier （DBR） and a line commutated inverter （LCI） between the generator term- inals and three-phase utility grid. A simple control technique for maximum power point tracking （MPPT） in wind energy conversion systems （WECS）, in which the firing angle of the LCI alone needs to be controlled by sensing the rotor speed of the generator has been proposed. The effectiveness of the proposed method of MPPT and method of analysis of this wind-driven SEIG-converter system connected to the grid through power converters has been demonstrated by experiments and simulation. These experimental and simulated results confirm the usefulness and successful working of the proposed system and its analysis.

Characterizations of high-voltage vertically-stacked GaAs laser power converter

Six-junction vertically-stacked Ga As laser power converters（LPCs） with n^＋-Ga As/p^＋-Al0.37 Ga0.63 As tunnel junctions have been designed and grown by metal-organic chemical vapor deposition for converting the power of 808 nm lasers. The LPC chips are characterized by measuring current–voltage（I–V） characteristics under 808 nm laser illumination, and a maximum conversion efficiency ηc of 53.1% is obtained for LPCs with an aperture diameter of 2 mm at an input laser power of 0.5 W. In addition, the characteristics of the LPCs are analyzed by a standard equivalent-circuit model, and the reverse saturation current, ideality factor, series resistance and shunt resistance are extracted by fitting of the I–V curves.

Circulating Current Suppression Method with Adaptive Virtual Impedance for Multi-bidirectional Power Converters Under Unbalanced Conditions

Multi-paralleled bidirectional power converters(BPCs)are commonly used to improve the power capacity and reliability in an AC/DC hybrid microgrid.However,circulating current through multi-BPCs has been one of the challenges and it can be aggravated in the presence of non-ideal operating conditions,such as unbalanced AC voltages,and the mismatch of hardware parameters.In order to suppress the circulating current,this paper proposes a distributed method based on adaptive virtual impedance,which also employs positive sequence power droop control and voltage deviation compensation control.The traditional positive sequence power droop control is adopted to only regulate the positive components of the BPCs output voltage.The negative sequence power term is fed to an adaptive virtual impedance generator to modify the damping characteristics of the BPCs.Also,an adaptive virtual impedance-based voltage deviation compensation method is proposed to recover the fluctuated output voltage of the BPCs due to droop action and the power fluctuations.The fully distributed regulation of adaptive virtual impedance enables the load power to be shared accurately among BPC modules and thus the circulating current can be effectively suppressed.The proposed control strategy does not require an additional communication system and the precise parameters of hardware equipment and line impedance.Furthermore,the effectiveness of the proposed method is verified by the experimental results.