Simulation realization of skip cycle mode integrated control circuit in the switching power supply with low standby loss

This paper explores and proposes a design solution of an integrated skip cycle mode （SCM） control circuit with a simple structure. The design is simulated and implemented with XD10H-1.0μm modular DIMOS 650 V process. In order to meet the requirement of a wide temperature range and high yields of products, the schematic extracted from the layout is simulated with five process corners at 27℃ and 90℃. Simulation results demonstrate that the proposed integrated circuit is immune to noise and achieves skipping cycle control when switching mode power supply （SMPS） works with low load or without load.

A new high-performance AC/DC power factor correction switching converter based on one-cycle control technology and active floating-charge technology

A new family of converters,high-performance AC/DC power factor correction(PFC) switching converters with one-cycle control technology and active floating-charge technology,was derived and experimentally verified.The topology of a single-phase CCM and DCM Boost-PFC switching converter was also analyzed.Its operating prniciples and control methods were expounded.Based on these,a new type of AC/DC switching converter circuits for PFC combined with one-cycle control technology was presented herein.The proposed AC/DC switching converter significantly helps improve the converter efficiency and its power factor value.

Power Transformer No-Load Loss Prediction with FEM Modeling and Building Factor Optimization

Estimation of power transformer no-load loss is a critical issue in the design of distribution transformers. Any deviation in estimation of the core losses during the design stage can lead to a financial penalty for the transformer manufacturer. In this paper an effective and novel method is proposed to determine all components of the iron core losses applying a combination of the empirical and numerical techniques. In this method at the first stage all computable components of the core losses are calculated, using Finite Element Method (FEM) modeling and analysis of the transformer iron core. This method takes into account magnetic sheets anisotropy, joint losses and stacking holes. Next, a Quadratic Programming (QP) optimization technique is employed to estimate the incomputable components of the core losses. This method provides a chance for improvement of the core loss estimation over the time when more measured data become available. The optimization process handles the singular deviations caused by different manufacturing machineries and labor during the transformer manufacturing and overhaul process. Therefore, application of this method enables different companies to obtain different results for the same designs and materials employed, using their historical data. Effectiveness of this method is verified by inspection of 54 full size distribution transformer measurement data.

Switching of Capacitors in an Asymmetric Induction Motor with Single-Phase Power,Triggering Several Applied Loads

xThis study has as its objective to collaborate with the expansion in the market of electric energy in rural areas,offering as such an innovative prospect to the solution of associated problems through use of the asymmetric three-phase induction motor,supplied by a single-phase source.In this system,capacitor switching is applied during operation,while theoretical and practical results are presented for the application of this switching in a three-phase asymmetric induction motor of 20 hp.

Effects of Dimensional Tolerances on the Friction Power Loss of Hydrodynamic Journal Bearing System

According to the dimensional tolerances on hydrodynamic journal bearing system, a nonlinear oil film force model was established,and the Reynolds' equation was solved by adopting finite difference method. In order to fulfill different dimensional tolerances in the system,adopting 2kfactor design and using the eccentricity ratio corresponding to the stability critical curve,the effects of the friction power loss brought by the dimensional tolerances of the dynamic viscosity,bearing width,bearing diameter and journal diameter were analyzed. The effect on dynamic characteristics of the hydrodynamic journal bearing system was quantitatively analyzed,and the nonlinear dynamic analysis, modeling and calculation methods were studied while considering the manufacturing tolerances. The results show that in contrast to the impacts of the tolerances in journal diameter,dynamic viscosity and bearing width,the bearing diameter tolerance would lead to the rise in the power loss, and the dimensional tolerances have different degrees of impacts on the journal bearing system. The friction power loss decreased as the eccentricity ratio increased, and when the eccentricity ratio was 0. 695 the power loss came to the minimum.The investigation would find the best solution and reduce energy consumption,then control varieties of nonlinear dynamical behavior effectively,and provide a theoretical basis for hydrodynamic journal bearing system in parameter design.

Implementation strategy for soft switching PFC with low output voltage

This paper proposes a novel implementation strategy for soft switching PFC whose circuit is simple and can achieve low voltage output directly. The main circuit adopts current mode full-bridge converter and all the power switches can realize ZCS or ZVS in the way of phase-shlfted control, using the leakage inductance of the transformer, the junction capacitor of the switches and the stored energy of the output capacitor. The problems such as the function of phase-shlfted link in control circuit, the implementation conditions of soft switching and bias restrained are analyzed. The adoption of constant frequency PWM control makes the design of the input and output filter link and the high frequency transformer simple. The transformation ratio regulation so as to achieve low voltage output and electrical insulation can be realized by using high frequency transformer.

An Improved Method of the Energy Loss Calculation Considering the Volatility of Wind Power Generation

The energy loss of the power grid is one of the key factors affecting the economic operation of power systems. How to calculate the electric energy consumption accurately will have a great influence on the planning, operation and management of the power grid. Currently there is a mountain of theoretical methods to calculate the line loss of the power system. However, these methods have some limitation, such as less considering the volatility of wind power resources. This paper presents an improved method to calculate the energy loss of wind power generation, considering the fluctuations of wind power generation. First, data are collected to obtain the curve of the typical daily expected output of wind farms for one month. Second, the curve of the typical daily expected output are corrected by the average electricity and the shape factor to obtain the curve of the typical daily equivalent output of wind farms for one month. Finally, the power flow is calculated by using typical daily equivalent output curve to describe the energy loss for one month. The results in the 110 kV main network show that the method is feasible.

IC Pattern Based Power Factor Maximization Model for Improved Power Stabilization

The voltagefluctuation in electric circuits has been identified as key issue in different electric systems.As the usage of electricity growing in rapid way,there exist higherfluctuations in powerflow.To maintain theflow or stabi-lity of power in any electric circuit,there are many circuit models are discussed in literature.However,they suffer to maintain the output voltage and not capable of maintaining power stability.To improve the performance in power stabilization,an efficient IC pattern based power factor maximization model(ICPFMM)in this article.The model is focused on improving the power stability with the use of IC(Inductor and Conductor)towards identifying most efficient circuit for the current duty cycle according to the input voltage,voltage in capacitor and output voltage required.The model with boost converter diverts the incoming voltage through number of conductors and inductors.By triggering specific inductor,a specific capacitor gets charged and a particular circuit gets on.The model maintains num-ber of IC(Inductor and Conductor)patterns through which the powerflow occurs.According to that,the pattern available,the mofset controls the level of power to be regulated through any circuit.From the pattern,the model computes the Cir-cuits Switching Loss and Circuits Conduction Loss for various circuits.Accord-ing to the input voltage,the model estimates Circuit Power Stabilization Support(CPSS)according to the voltage available in any capacitor and input voltage.Using the value of CPSS,the model trigger optimal number of circuits to maintain voltage stability.In this approach,more than one circuit has been triggered to maintain output voltage and to get charged.The proposed model not only main-tains power stability but also reduces the wastage in voltage which is not utilized.The proposed model improves the performance in voltage stability with less switching loss.

实际应用条件下Power MOSFET开关特性研究(下)

从功率MOSFET内部结构和极间电容的电压依赖关系出发,对功率MOSFET的开关现象及其原因进行了较深入分析。从实际应用的角度,对功率MOSFET开关过程的功率损耗和所需驱动功率进行了研究,提出了有关参数的计算方法,并对多种因素对开关特性的影响效果进行了实验研究,所得出的结论对于功率MOSFET的正确运用和设计合理的MOSFET驱动电路具有指导意义。

switched beam CDMA系统中小区容量和覆盖半径的计算

本文推导了switched beam系统中干扰因子的计算式,以及中断概率、基站接收机灵敏度、移动台最大可允许的发射功率、信干比的期望值、路径损耗与小区覆盖半径、小区容量的关系式,并以直线天线阵为例,计算了小区容量和小区的覆盖半径。

功率变换器中Power MOSFET功率损耗的数学分析及计算

为改善中、低压电力电子设备中开关器件的性能,给出了一种功率变换器的Power MOS-FET开关电路模型。其Power MOSFET的功率损耗主要由导通损耗和开关损耗构成,由此推导了功率变换器主电路中Power MOSFET的损耗计算公式,并根据实验波形的计算,得到Power MOS-FET的功率损耗。得到的计算结果表明:当开关频率较大时,开关损耗是Power MOSFET功率损耗的主要部分。

Unbalance Level Regulating Algorithm in Power Distribution Networks

The paper dwells on the unified power quality indexes characterizing the phenomenon of voltage unbalance in three-phase systems. Voltage unbalance is one of the commonest occurrences in the town mains of 0.38 kV voltage. The phenomenon describes as inequality of vector magnitude of phase voltage and shearing angle between them. Causes and consequences of the voltage unbalance in distribution networks have been considered. The algorithm, which allows switching one-phase load, has been developed as one of the methods of reducing the unbalance level. The algorithm is written in the function block diagram programming language. For determining the duration and magnitude of the unbalance level it is proposed to introduce the forecasting algorithm. The necessary data for forecasting are accumulated in the course of the algorithm based on the Function Block Diagram. The algorithm example is given for transforming substation of the urban electrical power supply system. The results of the economic efficiency assessment of the algorithm implementation are shown in conclusion. The use of automatic switching of the one-phase load for explored substation allows reducing energy losses (active electric energy by 7.63%;reactive energy by 8.37%). It also allows improving supply quality to a consumer. For explored substation the average zero-sequence unbalance factor has dropped from 3.59% to 2.13%, and the negative-sequence unbalance factor has dropped from 0.61% to 0.36%.

三电平辅助变流器寿命优化控制

辅助变流系统是动车组车辆上关键的电气组成部分,主要为空调机组、风机、照明等交流负载提供稳定的三相电源。结温是影响动车组三电平辅助变流器IGBT(Insulated-gate Bipolar Transistor)模块寿命的主要因素。为了提高动车组三电平中点钳位(Neutral-Point Clamped,NPC)型辅助变流器寿命,提出一种降低结温的模型预测电流控制(Model Predictive Current Control,MPCC)策略。首先,考虑传统MPCC在每个采样周期需要代入27个电压矢量循环计算,计算量较大,因此将三电平基本电压矢量划分在间隔60°的6个扇区中,通过计算电压矢量在两相静止坐标下的相角,进而判断参考电压矢量所处扇区,将备选矢量数目从27缩减至10,减少了计算量;其次,传统MPCC直接应用于动车组辅助变流器会使IGBT模块的结温较高,老化速度加快,对变流器安全稳定运行产生不可预测的损害,本文对IGBT模块的开关损耗和导通损耗进行近似等效,得到了和集射极电压、集电极电流相关的功率损耗因子。通过预测每相电流的方向,进而预测IGBT模块的开关和导通情况,动态加入功率损耗因子,并在代价函数中约束每相IGBT及其续流二极管(Free Wheeling Diode,FWD)的功率损耗,使得最优电压矢量在降低功率损耗的同时保证一定的控制性能。通过仿真与实验验证,本文所提方法相比传统MPCC策略降低了功率器件的结温,提高了变流器寿命。

High-Performance AC-DC Power Electronic Converter Generator for Hybrid-Solar Vehicles

This paper describes the principles of operation and the physical model of an advanced AC-DC converter generator （with the electronic converter acting as an AC-DC rectifier with reverse-conducting MOSFETs （metal-oxide semiconductor field-effect transistors） as fast-electronic switches with a relatively low ON-state voltage drop） for HSVs. An AC-DC converter, when seen as an AC-DC rectifier, can be used in many fields, e.g., for multi-functional AC-DC/DC-AC convener generator^starter and conventional DC-AC convener motors and AC-DC converter generators or generator sets, welding machines, etc. The paper also describes a novel AC-DC convener, with reverse-conducting transistors and without the use of optoelectronic separation （which does not require a separate power supply）, which may be easily realized in IC （integrated-circuit） technology. Computer simulation allows for waveform evaluation for timing analysis of all components of the AC-DC-converter＇s physical model, both during normal operation as well as in some states of emergency. The paper also presents the results of bench experimental studies where the MOSFETs were used as fast-electronic switches with a relatively low ON-state voltage drop. For experimental studies, a novel AC-DC converter has been put together on the Mitsubishi FM600TU-3A module. The AC-DC converter with reverse-conducting transistors in a double-way connection has a lot of advantages compared to the conventional AC-DC convener acting as a diode rectifier, such as higher energy efficiency and greater reliability resulting from the lower temperature of electronic switches.

A Novel Single-Switch Single-Stage Electronic Ballast

A single-stage single-switch high- frequency electronic ballast topology is presented. The circuit topology is the integration of a buck power- factor-correction （PFC） converter and a class E resonant inverter with only one active power switch. The buck converter is operated in discontinuous conduction mode and at a fixed switching frequency, and constant duty cycle to achieve high power factor and it can be controlled easily. Detailed analysis of the operation and characteristics of the circuit is provided. Simulation results satisfy present standard requirements.

混合级联十一电平逆变器功率与开关损耗双均衡倍频调制方法

混合级联多电平逆变器可以利用较少的开关器件实现较高电平输出,进而得到了广泛应用;但实现高低压单元间功率均衡难度更大。直流侧采用电池组模块进行供电时,功率达不到均衡会使得各H桥单元对应的电池组模块处于不同的放电特性,增大了故障概率和维修难度且增加了后期的维修成本。针对此问题,提出2种1:1:1:2混合级联十一电平逆变器功率和开关损耗双均衡倍频调制方法。首先,2种方法分别对3个低压单元采用三角载波、重构载波进行移相,从而实现在全调制度范围内将逆变器的等效开关频率由fc提高至6fc/12fc;使得低压单元各开关器件开关次数均围绕在60次/174次左右上下浮动,实现了低压单元内开关损耗均衡;使得调制度M=0.9/0.6/0.3时低压单元输出功率均围绕在657.5 W/293.5 W/73.5 W上下浮动,实现低压单元间的功率均衡,其次对高压单元采用阶梯波低频调制,随调制度的变化对导通角进行动态调整,使得高压单元各开关器件开关次数均为1次,实现了高低压单元内开关损耗均衡;使得调制度M=0.9/0.6/0.3时高压单元与低压单元输出功率均围绕在1317 W/657.5 W、586 W/293.5 W、146.5 W/73.5 W上下浮动,实现了高低压单元间功率均衡,之后对比分析2种方法各自的优缺点及其适用场合。最后,通过实验验证该方法的正确性和可行性,并给出了直流电压比为1:1:1:...:x的混合级联H桥逆变器双均衡的普适方法。

电动汽车用永磁同步电机的损耗分析

永磁同步电机(PMSM)作为电动汽车驱动电机的首选结构,被绝大多数的电动汽车使用。文章对永磁同步电机的功率损耗因素进行分析,并分析了功率损耗的数学计算模型。通过一款油冷式高速永磁同步电机展开了计算和实验,验证了数学计算模型的正确性。为研究油冷式永磁同步电机的功率损耗提供了一种方法。

一种无桥高增益单级LED驱动电路及其混合控制策略

中小功率的LED驱动电源中,传统两级LED驱动电源存在体积大、成本高以及传统Boost PFC电路在低压输入时导通损耗大等问题。为此提出一种由无桥二次型Boost PFC电路和DC-DC LLC电路集成的无桥高增益单级LED驱动电路,实现了高电压增益、功率开关器件软开关、一套控制电路和高电路转换效率。针对单级电路在电网输入电压变化引起直流母线电压变动范围大等问题,设计一种适用于所提电路的APWM-PFM混合控制策略,并对混合控制原理和控制过程进行详细分析。最后设计一台200 W的实验样机,在输入电压80~120 Vrms范围内,占空比最大为0.5,最大电压增益为6.7,直流母线电压基于网侧特性和LLC电路特性设计在700 V以内,样机的功率因数值均高于0.990,THD均低于15%。在满载条件下,110 Vrms输入时,样机效率为93.20%,相比于传统无桥PFC,电压增益提高了2.21倍,实现了高电压增益和软开关,有效提升了在低压输入条件下的电路转换效率。仿真和实验结果验证了所提出电路和控制方法的有效性。

集中式光伏电站发电效率提升研究综述

随着国家“双碳”目标的逐步推进,新能源特别是光伏发电占比不断提高,集中式光伏电站因其较高的发电效率而备受关注,成为我国未来电力发展的重要方向。集中式光伏电站是目前光伏发电领域中发展较为成熟的一种形式,其大规模的设计和建设为发电领域的可持续发展提供有效的解决方案。然而,如何进一步提升其发电效率一直是一个重要的研究课题。在集中式光伏发电站发电过程中,其发电效率与诸多因素有关。因此,为提升集中式光伏电站发电效率,该研究针对诸多影响因素进行分析,并给出具体提升策略,具有较高的实用性和推广价值。

基于改进鲸鱼算法优化模糊控制的开关电源

针对反激式开关电源的控制策略问题,传统的模糊PID控制下的电源输出稳定性低,同时出现负载突变时的控制效果较差。利用鲸鱼优化算法对模糊PID控制系统进行优化,并且使用Tent映射对鲸鱼算法中初始种群进行混沌化,通过混沌鲸鱼优化算法对模糊PID控制系统中的论域进行优化,使得该控制系统下的反激式开关电源输出稳定度和抗干扰能力得到提升。基于Matlab软件完成反激式开关电源建模进行仿真研究。仿真结果表明,CWOA-FPID下的反激式开关电源的稳定性优于鲸鱼算法和粒子群算法优化下的控制器,当负载从10Ω变到5Ω时,本文下的控制策略相比较其它两个算法在电压恢复时间和电压输出突变都有显著优势。验证了改进鲸鱼算法优化的模糊PID控制器能够更好的满足反激式开关电源的控制要求。