Power Matching and Energy Efficiency Improvement of Hydraulic Excavator Driven with Speed and Displacement Variable Power Source

Mobile machinery energy efficiency and emission pollution are the national and worldwide issues. This paper contributes in solving these problems by applying a speed variable power source. Unfortunately, almost all of the speed variable systems have the dynamic response problem when the motor starts with full load or heavy load. To address this problem, a hydraulic accumulator is used to balance the load of the power source for assisting starting of the motor and a matching method combined with speed and displacement control of the pump is proposed to improve the energy efficiency and dynamic performance simultaneously under different working conditions. Also, the power source/valve combined control strategy of an independent metering system is designed to realize flow matching of the whole system. Firstly, a test system is established to study the dynamic performance and energy efficiency of the speed variable power source with an auxiliary accumulator. Working performance and energy consumption of the power source under different rotating speeds and different loads are studied. And then, the hydraulic excavator test rig with the proposed system is constructed. Furthermore, the working performance of the excavator with the speed-fixed and speed-variable strategy are studied comparatively. Results show that, compared with fixed-speed strategy, the electric power consumption during the idle period and partial load condition can be reduced about 2.05 kW and 1.37 kW. The energy efficiency of speed variable power source is about 40%-71%, which is higher than that of the fixed-speed power source by 3%–10%.

Effect of ultrasonic power and casting speed on solidification structure of 7050 aluminum alloy ingot in ultrasonic field

With the experiment and finite element simulation, the influences of power ultrasonic on the solidification structure of 7050 aluminum alloy ingot in semi-continuous casting were researched, and the effects of casting speed on solidification structure in ultrasonic field were also analyzed. The experiment and simulation results show that the solidification structure of the ingot is homogeneously distributed, and its grain size is obviously refined at ultrasonic power of 240 W. The average grain sizes, which can be seen from the Leica microscope, are less than 100 μm. When the casting speed is 45-50 mm/min, the best grain refinement is obtained.

The research of power saving frequency conversion speed regulation experiment system

A power saving frequency difference controlling method was introduced by the double inverter and motor experiment system.The characters of the system under differ- ent loads were investigated.The theoretical analysis and experiment results show the frequency difference method is a ideal power saving speed regulation method for the dou- ble inverter and motor system.The experiment system is simply structured,convenient to operate and provides a new way of character testing for frequency conversion speed regulation.

Design of Low Power and High Speed CMOS Comparator for A/D Converter Application

This paper presents an improved method for design of CMOS comparator based on a preamplifier-latch circuit driven by a clock. Design is intended to be implemented in Sigma-delta Analog-to-Digital Converter (ADC). The main advantage of this design is capable to reduce power dissipation and increase speed of an ADC. The design is simulated in 0.18 μm CMOS Technology with Cadence environment. Proposed design exhibits good accuracy and a low power consumption about 102 μW with operating sampling frequency 125 MHz and 1.8 V supply. Simulation results are reported and compared with earlier work done and improvements are observed in this work.

Research on H_2 speed governor for diesel engine of marine power station

The frequency stability of a marine power system is determined by the dynamic characteristic of the diesel engine speed regulation system in a marine power station. In order to reduce the effect of load disturbances and improve the dynamic precision of a diesel engine speed governor, a controller was designed for a diesel engine speed regulation system using H2 control theory. This transforms the specifications of the system into a standard H2 control problem. Firstly, the mathematical model of a diesel engine speed regulation system using an H2 speed governor is presented. To counter external disturbances and model uncertainty, the design of an H2 speed governor rests on the problem of mixed sensitivity. Computer simulation verified that the H2 speed governor improves the dynamic precision of a system and the ability to adapt to load disturbances, thus enhancing the frequency stability of marine power systems.

Piezoelectric Power Harvesting via Acoustic-Pressure Driven by Low-Speed Wind-Force with Resonating-Tube and Wind-Collector

Wind-driven power harvestings attract attentions since their target wind speeds are quite low less than the so-called cut-in wind speed, which is generally recognized as around 3 m/s. The extant power harvestings driven by wind-induced-air-column-resonations (i.e. acoustic-pressures) are still lacking simplicity, scale flexibility and solid strategies for practical applications. Therefore, the piezoelectric power harvesters via acoustic-pressures driven by low-speedwind-forces with resonating-tubes and wind-collectors were invented so as to complement all the lacks. The wind-collector as well as the resonating-tube contributed to upraise the power harvesting density. The champion power harvesting density of 19.5 nW/dm2 could be procured at 2.3 m/s of an artificial wind and the optimal resonating-tube and wind-collector. Power harvesting proofs from the natural wind with low mean speeds down to about 0.6 m/s were successfully obtained. The cut-in wind speed of the prototype piezoelectric power harvester was found to be quite low as about 0.4 m/s, signifying its ubiquity. Finally, a multi-bundle pendant-type piezoelectric power harvester was specifically presented together with professing the solid and multiple strategies for practical applications.

Bootstrapped Multi-Model Neural-Network Super-Ensembles for Wind Speed and Power Forecasting

The bootstrap resampling method is applied to an ensemble artificial neural network (ANN) approach (which combines machine learning with physical data obtained from a numerical weather prediction model) to provide a multi-ANN model super-ensemble for application to multi-step-ahead forecasting of wind speed and of the associated power generated from a wind turbine. A statistical combination of the individual forecasts from the various ANNs of the super-ensemble is used to construct the best deterministic forecast, as well as the prediction uncertainty interval associated with this forecast. The bootstrapped neural-network methodology is validated using measured wind speed and power data acquired from a wind turbine in an operational wind farm located in northern China.

Stability Enhancement of Small-Scale Power Grid with Renewable Power Sources by Variable Speed Diesel Power Plant

This paper proposes a power control method to improve a stability of a small-scale power grid with renewable energy sources. In an isolated small- scale power grid such as an island, diesel power plant is main power source which has an environmental burden and expensive running cost due to high priced fossil fuel. Thus, expanding installation of the renewable energy sources such as a wind power is strongly desirable. Such fluctuating energy sources, however, harm power quality of the small-scale power grid, and in addition, conventional power plant in the small-scale power grid cannot, in general, stabilize the grid system with such fluctuating power sources. In this study, Variable Speed Doubly-Fed Induction Generator (VS-DFIG) is proposed to be in-stalled at a diesel power plant instead of a conventional Fixed Speed Synchronous Generator (FS-SG), because quick control of a power balance in the small-scale power grid can be achieved by using the inertial energy of VS-DFIG. In addition, utilization of a Battery Energy Storage System (BESS) is also considered to assist cooperatively the VS-DFIG control. As a result of the simulation analysis by using the proposed method, it is verified that frequency fluctuations due to renewable energy source can be effectively reduced by quick power control of the VS-DFIG compared to the conventional FS-SG, and further control ability can be obtained by utilizing BESS. Moreover, the transient stability of a small-scale power grid during a grid fault can also be enhanced.

A Statistical Analysis of Wind Speed and Power Density Based on Weibull and Rayleigh Models of Jumla, Nepal

In the present study, wind speed data of Jumla, Nepal have been statistically analyzed. For this purpose, the daily averaged wind speed data for 10 year period (2004-2014: 2012 excluded) provided by Department of Hydrology and Meteorology (DHM) was analyzed to estimate wind power density. Wind speed as high as 18 m/s was recorded at height of 10 m. Annual mean wind speed was ascertained to be decreasing from 7.35 m/s in 2004 to 5.13 m/s in 2014 as a consequence of Global Climate Change. This is a subject of concern looking at government’s plan to harness wind energy. Monthly wind speed plot shows that the fastest wind speed is generally in month of June (Monsoon Season) and slowest in December/January (Winter Season). Results presented Weibull distribution to fit measured probability distribution better than the Rayleigh distribution for whole years in High altitude region of Nepal. Average value of wind power density based on mean and root mean cube seed approaches were 131.31 W/m2/year and 184.93 W/m2/year respectively indicating that Jumla stands in class III. Weibull distribution shows a good approximation for estimation of power density with maximum error of 3.68% when root mean cube speed is taken as reference.

A Low Power and High Speed Viterbi Decoder Based on Deep Pipelined, Clock Blocking and Hazards Filtering

A high speed and low power Viterbi decoder architecture design based on deep pipelined, clock gating and toggle filtering has been presented in this paper. The Add-Compare-Select (ACS) and Trace Back (TB) units and its sub circuits of the decoder have been operated in deep pipelined manner to achieve high transmission rate. The Power dissipation analysis is also investigated and compared with the existing results. The techniques that have been employed in our low-power design are clock-gating and toggle filtering. The synthesized circuits are placed and routed in the standard cell design environment and implemented on a Xilinx XC2VP2fg256-6 FPGA device. Power estimation obtained through gate level simulations indicated that the proposed design reduces the power dissipation of an original Viterbi decoder design by 68.82% and a speed of 145 MHz is achieved.

核电半速汽轮发电机励磁绕组匝间短路时转子涡流损耗研究

为研究核电半速汽轮发电机励磁绕组匝间短路时转子涡流损耗特性,推导了核电半速汽轮发电机空载运行时励磁绕组匝间短路故障下,定子分数次谐波环流产生的合成磁动势表达式,分析合成磁动势相对于转子的转速,揭示了转子表面产生涡流的原因以及涡流的频率特性。结合涡流损耗计算方法,以一台核电半速汽轮发电机为例进行了仿真验证。在此基础上,对核电半速汽轮发电机励磁绕组不同位置发生相同程度匝间短路,以及励磁绕组发生不同程度匝间短路过程进行了仿真,计算了转子各阻尼条及槽楔中的涡流及涡流损耗,揭示了励磁绕组匝间短路时影响转子阻尼条及槽楔中涡流和涡流损耗的因素。为核电半速汽轮发电机励磁绕组匝间短路故障时,分析转子发热的影响因素提供了理论基础。

On maximum power point tracking control strategy for variable speed constant frequency wind power generation

Based on the characteristic of AC-excited variable speed constant frequency(VSCF)wind power generation,the vector control technique was applied in a doubly fed induction generator(DFIG).Maximum wind energy or maximum output power point can be tracked by decoupling control of active power and reactive power.The research result shows that the net power of generation system delivered to grid in maximum wind energy tracking mode is not the most.We presented a novel maximum power point tracking(MPPT)control strategy by analyzing the DFIG mathematic model and power relations which delivered the maximum power to the grid.The maximum power point could be tracked automatically without measuring wind speed in the control strategy and the control was independent of optimal turbine power curve,which had excellent dynamic and static performances and robustness.Simulation and experimental results testify the accuracy and validity of the control strategy.

A novel technology for control of variable speed pumped storage power plant

Variable speed pumped storage machines are used extensively in wind power plant and pumped storage power plant. This paper presents direct torque and flux control(DTFC) of a variable speed pumped storage power plant(VSPSP). By this method both torque and flux have been applied to control the VSPSP. The comparison between VSPSP's control strategies is studied. At the first, a wind turbine with the capacity 2.2 k W and DTFC control strategies simulated then a 250 MW VSPSP is simulated with all of its parts(including electrical, mechanical, hydraulic and its control system) by MATLAB software. In all of simulations, both converters including two-level voltage source converter(2LVSC) and three-level voltage source converter(3LVSC) are applied. The results of applying 2LVSC and 3LVSC are the rapid dynamic responses with better efficiency, reducing the total harmonic distortion(THD) and ripple of rotor torque and flux.

计及误差信息的自适应超短期风速预测模型

为提升超短期风速预测精度,提出一种计及误差信息的自适应混合预测模型。应用自适应噪声的完备集合经验模态分解模型与鲸鱼优化的变分模态分解模型分别对风速样本数据与预测误差进行分解,同时计算各子序列的模糊熵以判断序列复杂程度。在此基础上,应用鲸鱼优化的长短期网络预测复杂程度较高的序列,差分自回归移动平均模型预测复杂程度较低的序列。最后,将初始风速预测结果和风速误差预测值相加得到基于误差修正的超短期风速预测值。结果表明,修正预测误差与考虑分解策略可有效提升点预测的性能,与基准模型相比,所提模型在多场景下均具备优良的预测精度。