Review of the Analysis and Suppression for High-frequency Oscillations of the Grid-connected Wind Power Generation System

High-frequency oscillation(HFO)of gridconnected wind power generation systems(WPGS)is one of the most critical issues in recent years that threaten the safe access of WPGS to the grid.Ensuring the WPGS can damp HFO is becoming more and more vital for the development of wind power.The HFO phenomenon of wind turbines under different scenarios usually has different mechanisms.Hence,engineers need to acquire the working mechanisms of the different HFO damping technologies and select the appropriate one to ensure the effective implementation of oscillation damping in practical engineering.This paper introduces the general assumptions of WPGS when analyzing HFO,systematically summarizes the reasons for the occurrence of HFO in different scenarios,deeply analyses the key points and difficulties of HFO damping under different scenarios,and then compares the technical performances of various types of HFO suppression methods to provide adequate references for engineers in the application of technology.Finally,this paper discusses possible future research difficulties in the problem of HFO,as well as the possible future trends in the demand for HFO damping.

Low-frequency oscillation of train-network system considering traction power supply mode

The low-frequency oscillation(LFO)has occurred in the train-network system due to the introduction of the power electronics of the trains.The modeling and analyzing method in current researches based on electrified railway unilateral power supply system are not suitable for the LFO analysis in a bilateral power supply system,where the trains are supplied by two traction substations.In this work,based on the single-input and single-output impedance model of China CRH5 trains,the node admittance matrices of the train-network system both in unilateral and bilateral power supply modes are established,including three-phase power grid,traction transformers and traction network.Then the modal analysis is used to study the oscillation modes and propagation characteristics of the unilateral and bilateral power supply systems.Moreover,the influence of the equivalent inductance of the power grid,the length of the transmission line,and the length of the traction network are analyzed on the critical oscillation mode of the bilateral power supply system.Finally,the theoretical analysis results are verified by the time-domain simulation model in MATLAB/Simulink.

Potential Power of the Pyramidal Structure VIII: Exploration of Periodic Diurnal Oscillation of Pyramid Power and Bio-Entanglement

To date, numerous books have been published on so-called “pyramid power” but there have been few academic papers on this subject other than our own. Since 2007, to demonstrate the pyramid power, we have undertaken strictly scientific experiments using a pyramidal structure (PS) that we have carefully constructed. In previous reports, we used the edible cucumber, Cucumis sativus as an effective and practical biosensor. Through measurement and analysis of volatile components (gas concentrations) emitted from the biosensor, we were able to demonstrate the existence of the pyramid power and revealed some of its characteristics. In a paper published in 2022, we showed that gas concentration release from this biosensor displayed a circadian rhythm and that this rhythm changed with the season. Based on the result that the biosensor had a periodic diurnal oscillation called a circadian rhythm, we questioned whether or not pyramid power and Bio-Entanglement also had periodic diurnal oscillations. In this paper, we investigated that possibility. Our results have shown that pyramid power and Bio-Entanglement do not exhibit significant periodic diurnal oscillations. Thus we have revealed for the first time that the field associated with pyramid power is a type of static field that always exerts a constant influence. We expect that our research results will be widely accepted in the future and will become the foundation for a new research field in science, with a wide range of applications.

Improvement of circuit oscillation generated by underwater high voltage pulse discharges based on pulse power thyristor

High voltage fracturing technology was widely used in the field of reservoir reconstruction due to its advantages of being clean, pollution-free, and high-efficiency. However, high-frequency circuit oscillation occurs during the underwater high voltage pulse discharge process, which brings security risks to the stability of the pulse fracturing system. In order to solve this problem, an underwater pulse power discharge system was established, the circuit oscillation generation conditions were analyzed and the circuit oscillation suppression method was proposed. Firstly, the system structure was introduced and the charging model of the energy storage capacitor was established by the state space average method. Next, the electrode high-voltage breakdown model was established through COMSOL software, the electrode breakdown process was analyzed according to the electron density distribution image, and the plasma channel impedance was estimated based on the conductivity simulation results. Then the underwater pulse power discharge process and the circuit oscillation generation condition were analyzed, and the circuit oscillation suppression strategy of using the thyristor to replace the gas spark switch was proposed. Finally, laboratory experiments were carried out to verify the precision of the theoretical model and the suppression effect of circuit oscillation. The experimental results show that the voltage variation of the energy storage capacitor, the impedance change of the pulse power discharge process, and the equivalent circuit in each discharge stage were consistent with the theoretical model. The proposed oscillation suppression strategy cannot only prevent the damage caused by circuit oscillation but also reduce the damping oscillation time by77.1%, which can greatly improve the stability of the system. This research has potential application value in the field of underwater pulse power discharge for reservoir reconstruction.

A new wide area damping controller design method considering signal transmission delay to damp interarea oscillations in power system

Wide area damping controller(WADC) is usually utilized to damp interarea low frequency oscillation in power system. However, conventional WADC design method neglects the influence of signal transmission delay and damping performance of WADC designed by the conventional method may deteriorate or even has no effect when signal transmission delay is beyond delay margin, an index that denotes delay endurance degree of power system. Therefore, a new design method for WADC under the condition of expected damping factor and required signal transmission delay is presented in this work. An improved delay margin with less conservatism is derived by adopting a new Lyapunov-Krasovskii function and more compact bounding technique on the derivative of Lyapunov-Krasovskii functional. The improved delay margin, which constructs the correlation of damping factor and signal transmission delay, can be used to design WADC. WADC designed by the proposed method can ensure that power system satisfies expected damping factor when WADC input signal is delayed within delay margin. Satisfactory test results demonstrate the effectiveness of the proposed method.

A low-phase-noise and low-power crystal oscillator for RF tuner

A 37. 5 MHz differential complementary metal oxide semiconductor （CMOS） crystal oscillator with low power and low phase noise for the radio frequency tuner of digital radio broadcasting digital radio mondiale （DRAM） and digital audio broadcasting （DAB） systems is realized and characterized. The conventional cross-coupled n-type metal oxide semiconductor （NMOS） transistors are replaced by p-type metal oxide semiconductor （PMOS） transistors to decrease the phase noise in the core part of the crystal oscillator. A symmetry structure of the current mirror is adopted to increase the stability of direct current. The amplitude detecting circuit made up of a single- stage CMOS operational transconductance amplifier （OTA） and a simple amplitude detector is used to improve the current accuracy of the output signals. The chip is fabricated in a 0. 18- pxn CMOS process, and the total chip size is 0. 35 mm x 0. 3 mm. Under a supply voltage of 1.8 V, the measured power consumption is 3.6 mW including the output buffer for 50 testing loads. The proposed crystal oscillator exhibits a low phase noise of - 134. 7 dBc/Hz at 1-kHz offset from the center frequency of 37. 5 MHz.

Characteristic Analysis of Power Oscillations Caused by Disharmony Among Voltage-source-controlled Units in Three-terminal Local Power Grid

Previous studies have demonstrated that disharmony among voltage-source-controlled units(VSCUs)may occur on an alternating current(AC)transmission or distribution line under steady-state operating conditions(SSOCs)or quasistatic operating conditions(QSSOCs).As the studies on frequency disharmony have been expanded to multiple disharmonized vS-CUs in the local power grid,its adverse effects on AC lines and equivalent load(EL)at the bus without active voltage control ability(non-active bus)need to be investigated further.Considering the locality of disharmony and common topological con-nections among VSCUs,this paper adopts a Y-type three-termi-nal local power grid(LPG)as the research object.The disharmony among the three VSCUs is discussed.Firstly,for the load at non-active bus,the formulas for single-phase instantaneous voltage,load current,load power,as well as average power un-der disharmony operating conditions(DOCs)are derived.The characteristic indicators of the above electrical quantities are defined,which can measure the amplification and reduction de-grees of the above electrical quantities before and after disharmony.Secondly,for the line directly connected to VSCUs,the formulas for single-phase instantaneous line current and power and the average power under DOCs are derived.The characteristic indicators of power flow are defined,which can be used to quantify the peak amplification impact of oscillation before and after disharmony.Finally,the case study on the Y-type three-terminal LPG under the single-disharmony and the multi-dis-harmony switching scenarios indicates that the long-period pow-er oscillation caused by disharmony may occur in the load flow at the non-active bus and the line flow.The oscillation causes a serious decrease in load capability and a significant amplification of the peak of line power oscillation.

Investigation on the Oscillating Buoy Wave Power Device

An oscillating buoy wave power device (OD) is a device extracting wave power by an oscillating buoy. Being excited by waves, the buoy heaves up and down to convert wave energy into electricity by means of a mechanical or hydraulic device. Compared with an Oscillating Water Column (OWC) wave power device, the OD has the same capture width ratio as the OWC does, but much higher secondary conversion efficiency. Moreover, the chamber of the OWC, which is the most expensive and difficult part to be built, is not necessary for the OD, so it is easier to construct an OD. In this paper, a numerical calculation is conducted for an optimal design of the OD firstly, then a model of the device is built and, a model test is carried out in a wave tank. The results show that the total efficiency of the OD is much higher than that of the OWC and that the OD is a promising wave power device.

Fixed time integral sliding mode controller and its application to the suppression of chaotic oscillation in power system

Chattering phenomenon and singularity are still the main problems that hinder the practical application of sliding mode control. In this paper, a fixed time integral sliding mode controller is designed based on fixed time stability theory, which ensures precise convergence of the state variables of controlled system, and overcomes the drawback of convergence time growing unboundedly as the initial value increases in finite time controller. It makes the controlled system converge to the control objective within a fixed time bounded by a constant as the initial value grows, and convergence time can be changed by adjusting parameters of controllers properly. Compared with other fixed time controllers, the fixed time integral sliding mode controller proposed in this paper achieves chattering-free control, and integral expression is used to avoid singularity generated by derivation. Finally, the controller is used to stabilize four-order chaotic power system. The results demonstrate that the controller realizes the non-singular chattering-free control of chaotic oscillation in the power system and guarantees the fixed time convergence of state variables, which shows its higher superiority than other finite time controllers.

High power high beam quality diode-pumped 1319-nm Nd:YAG oscillator-amplifier laser system

This paper demonstrated a high power and high beam quality diode-pumped 1319-nm Nd：YAG master oscillator-power amplifier laser system. A thermally near-unstable resonator with four-rod birefringence compensation fiat-fiat cavity was adopted as the master oscillator. A solid etalon was inserted in the unidirectional ring resonator to compress the laser linewidth. Under a repetition rate of 500 Hz and pulse width of 160 μs, the master oscillator delivers an average output power of 16.8 W at 1319 nm with linear polarisation, beam quality factor M^2=1.16 and linewidth of 3.2 GHz. A double-pass power amplifier with two amplifier stages was employed for higher power scaling and the output power was amplified to be 25.9 W with M^2 = 1.43.

PROPOSALS CONCERNING THE RESEARCH WORK OF TURBOGENERATOR TORSIONAL OSCILLATIONS IN CHINA

In this paper,proposals in the following arcas of turbogenerator torsionaloscillation(TTO)researches in China are presented:* Concerning the focal points of TTO studies;* Concerning the modelling and data acquisition of TTO;* Concerning the computation and analysis of TTO transients;* Concerning the monitoring and analyzing devices of TTO;* Concerning the countermeasures against TTO.It is concluded that researches centered on torsional oscillations caused by system dis-turbances and switching events should begin the carlier the better.

PMU Based Monitoring and Estimation of Inter-area Power Oscillation for Singapore-Malaysia Interconnection Power System

This paper proposes a PMU （phasor measurement unit） based monitoring and estimation scheme of power system small-signal stability in Singapore-Malaysia interconnection power system through a 50-Hz and 500 kV transmission line. Two PMUs are installed in the power system interconnection network of Singapore-Malaysia. One PMU is located in Singapore and the other one in Malaysia （Penang）. Both PMUs measure the single-phase voltage phasor. The data filtering technique based on FFT （Fast Fourier Transform） is employed to extract oscillation data for single mode. Finally, some analysis results of monitoring and estimation of Singapore-Malaysia interconnected power system based on application practice of the CampusWAMS are presented and analyzed.

CHAOTIC OSCILLATION OF ANONLINEAR POWER SYSTEM

For a nonlinear power transmission system, the residue calculus method is introduced and applied to study its heteroclinic bifurcation. There a cone region and a strip region of parameters are obtained, in which the power transmission system displays chaotic oscillation. This gives a theoretic analysis and a computational method for the purpose to control the nonlinear system with deviation stably running.

Analysis of Nonlinear Characteristics of Turbine Governor and Its Impact on Power System Oscillation

In this paper, the model of turbine governor?based on the physical principles is constituted to improve the accuracy of power system dynamic simulation, making the results of simulation consistent with the actual situation. The unit and grid coupling model which reflects the interaction between thermal system of power plant and power system is built using EMTDC/PSCAD. The influence of nonlinear characteristics on the valve opening and the steam turbine mechanical power is also analyzed in this paper. The results of simulation show that the improper setting of parameters reflecting nonlinear characteristics of turbine governor can lead to the cyclical oscillations of the valve opening and the?steam turbine mechanical power, and even can lead to the power oscillation persistently. The research achievements in this paper have a certain reference value on exploring the causes of power oscillation from the prime mover.

Incoherent and coherent beam combination for master oscillator/power amplifier system with stimulated Brillouin scattering mirror

In this paper, we studied incoherent and coherent beam combining for the master oscillator/power amplifier （MOPA） system with stimulated Brillouin scattering （SBS） mirror. Optic field intensity distributions in the near and far field are numerically calculated for the two kinds of system. The results show that good beam quality in the far field could be obtained. It provides a theoretical basis for experimental research in the future.

Homotopy Analysis Method for a Conservative Nonlinear Oscillator with Fractional Power

In this paper, the homotopy analysis method is applied to deduce the periodic solutions of a conservative nonlinear oscillator for which the elastic force term is proportional to u1/3. By introducing the auxiliary linear operator and the initial guess of solution, the homotopy analysis solving is set up. By choosing the suitable convergence-control parameter, the accurate high-order approximations of solution and frequency for the whole range of initial amplitudes can easily be obtained. Comparison of the results obtained using this method with those obtained by different methods reveals that the former is more accurate, effective and convenient for these types of nonlinear oscillators.

Power Series Solution for Strongly Non-linear Conservative Oscillators

This paper compares the accuracy of the power series approach with that of the modified Lindstedt-Poincare method for strongly nonlinear vibration.The free vibration of an undamped Duffing oscillator is considered because it has an exact solution.In the power series approach,the time variable is transformed into an“oscillating time”which reduces the governing equation to a form well-conditioned by the power series method.The results show that the power series approach provides extremely accurate vibration frequencies,even at large values of the nonlinear parameter,compared with errors of up to nine percent for the modified Lindstedt-Poincare method.

Solution of Duffing-Harmonic Oscillator by the Power Series Method

This paper provides a power series solution to the Duffing-harmonic oscillator and compares the frequencies with those obtained by the harmonic balance method.To capture the periodic motion of the oscillator,the power series expansion is used upon transforming the time variable into an“oscillating time”which reduces the governing equation to a form well-conditioned for a power series solution.A recurrence equation for the series coefficients is established in terms of the“oscillating time”frequency which is then determined by employing Rayleigh’s energy principle.The response of the oscillator is compared with a numerical solution and good agreement is demonstrated.

Generation of Optimal Voltage Reference for Limit Cycle Oscillation in Digital Control-Based Switching Power Supply

Digital control of a general-purpose switching power supply is one of the key technologies to perform the high reliability and the intelligent function demanded for the next generation. The contribution of this paper is the development of a digital control-based switching power supply. In the developed system, the generation method of the optimal voltage reference to eliminate the limit cycle oscillation of output voltage due to the AD/DA resolution is proposed. In the proposed method, the variation of the input power source voltage can be also compensated. The effectiveness of the proposed optimal reference generation method is experimentally verified.

Ring Oscillator for 60 Meter Bandwidth

The 60-meter band range is tremendously useful in telecommunication,military and governmental applications.The I.T.U.(International Telecommunication Union)required isolationism to former radio frequency services because the various frequency bands are extremely overloaded.The allocation of new frequency bands are a lengthy procedure as well as time taking.As a result,the researchers use bidirectional,amateur radio frequency communication for 60-meter band,usually the frequency slot of 5250-5450 KHz,although the entire band is not essentially obtainable for all countries.For transmission and reception of these frequencies,a local oscillator is used in the mixer unit to generate the local signal for mixing the input and reference signals.For this function different type of oscillators are used.In this paper,a three-stage ring oscillator is designed with 1 V supply.Ring oscillators(RO)is the base to explore like to identifying,specify with modelling resources in the disparity in behaviour of the circuit in terms of industrialized design and layout parameters.This type of oscillators are free from noise as inductor is not used to the circuit as in LC oscillator,Heartly oscillator,Colpitt and tuned oscillators.The present approach of circuit designing,the scaling of CMOS(Complementary Metal Oxide Semiconductor)transistor will moderate,the procedure variability.In the forthcoming article,a ring oscillator with fixed capacitor(1 pF)and with variable capacitors(1 to 100 pF)is analysed.The frequency analysis with different capacitor is performed.The total delay of 3-stage oscillator is 4.82 ns with 5.2 MHz oscillation frequency.The overall Power dissipation of the circuit is 1.852μWat 1 V supply.The simulation analysis is performed on 45 nm CMOS technology with both transistor width are 278 and 420 nm.