This paper dealt with the influence of residual stress on the dimensional instability of 7075 aluminum cone-shaped shells. Finite element method was introduced to calculate residual stress distributions in 7075 alumin...This paper dealt with the influence of residual stress on the dimensional instability of 7075 aluminum cone-shaped shells. Finite element method was introduced to calculate residual stress distributions in 7075 aluminum cone-shaped shells during conventional heat treatment (CHT) and deep cryogenic treatment (DCT). An example was given to demonstrate effects of deep cryogenic treatment (DCT) and conventional heat treatment (CHT) on dimensional instability. It is concluded that initial residual stresses have detrimental influence on the dimensional instability of 7075 aluminum cone-shaped shells.展开更多
In this study,the cooling rate was manipulated by quenching with water of different temperatures(30,60 and 100℃).Surface and internal residual stresses in the quenched 6061 aluminum alloy samples were measured using ...In this study,the cooling rate was manipulated by quenching with water of different temperatures(30,60 and 100℃).Surface and internal residual stresses in the quenched 6061 aluminum alloy samples were measured using hole-drilling and crack compliance methods,respectively.Then,the processability of the quenched samples was evaluated at cryogenic temperatures.The mechanical properties of the as-aged samples were assessed,and microstructure evolution was analyzed.The surface residual stresses of samples W30℃,W60℃and W100℃is−178.7,−161.7 and−117.2 MPa,respectively along x-direction,respectively;and−191.2,−172.1 and−126.2 MPa,respectively along y-direction.The sample quenched in boiling water displaying the lowest residual stress(~34%and~60%reduction in the surface and core).The generation and distribution of quenching residual stress could be attributed to the lattice distortion gradient.Desirable plasticity was also exhibited in the samples with relatively low quenching cooling rates at cryogenic temperatures.The strengthes of the as-aged samples are 291.2 to 270.1 MPa as the quenching water temperature increase from 30℃to 100℃.Fine and homogeneous β"phases were observed in the as-aged sample quenched with boiling water due to the clusters and Guinier-Preston zones(GP zones)premature precipitated during quenching process.展开更多
Use of magnesium is the need of the hour due to its low density as well as its high strength-to-weight and stiffness-to-weight ratio etc.This study focuses on the effectiveness of liquid nitrogen(LN_(2))assisted cryog...Use of magnesium is the need of the hour due to its low density as well as its high strength-to-weight and stiffness-to-weight ratio etc.This study focuses on the effectiveness of liquid nitrogen(LN_(2))assisted cryogenic machining on the surface integrity(SI)characteristics of AZ91 magnesium alloy.Face milling using uncoated carbide inserts have been performed under liquid nitrogen(LN_(2))assisted cryogenic condition and compared with conventional(dry)milling.Experiments are performed using machining parameters in terms of cutting speeds of 325,475,625 m/min,feed rates of 0.05,0.1,0.15 mm/teeth and depth of cuts of 0.5,1,1.5 mm respectively.Most significant surface integrity characteristics such as surface roughness,microhardness,microstructure,and residual stresses have been investigated.Behaviour of SI characteristics with respect to milling parameters have been identified using statistical technique such as ANOVA and signal-to-noise(S/N)ratio plots.Additionally,the multi criteria decision making(MCDM)techniques such as additive ratio assessment method(ARAS)and complex proportional assessment(COPRAS)have been utilized to identify the optimal conditions for milling AZ91 magnesium alloy under both dry and cryogenic conditions.Use of LN_(2)during machining,resulted in reduction in machining temperature by upto 29%with a temperature drop from 251.2℃under dry condition to 178.5℃in cryogenic condition.Results showed the advantage of performing cryogenic milling in improving the surface integrity to a significant extent.Cryogenic machining considerably minimized the roughness by upto 28%and maximised the microhardness by upto 23%,when compared to dry machining.Cutting speed has caused significant impact on surface roughness(95.33%-dry,92.92%-cryogenic)and surface microhardness(80.33%-dry,82.15%-cryogenic).Due to the reduction in machining temperature,cryogenic condition resulted in compressive residual stresses(maximumσ║=-113 MPa)on the alloy surface.Results indicate no harm to alloy microstructure in both conditions,with no alterations to grain integrity and minimal reduction in the average grain sizes in the near machined area,when compared to before machined(base material)surface.The MCDM approach namely ARAS and COPRAS resulted in identical results,with the optimal condition being cutting speed of 625 m/min,a feed rate of 0.05 mm/teeth,and a depth of cut of 0.5 mm for both dry and cryogenic environments.展开更多
文摘This paper dealt with the influence of residual stress on the dimensional instability of 7075 aluminum cone-shaped shells. Finite element method was introduced to calculate residual stress distributions in 7075 aluminum cone-shaped shells during conventional heat treatment (CHT) and deep cryogenic treatment (DCT). An example was given to demonstrate effects of deep cryogenic treatment (DCT) and conventional heat treatment (CHT) on dimensional instability. It is concluded that initial residual stresses have detrimental influence on the dimensional instability of 7075 aluminum cone-shaped shells.
基金Project(2021GK1040)supported by the Major Projects of Scientific and Technology Innovation of Hunan Province,ChinaProject(52375398)supported by the National Natural Science Foundation of China。
文摘In this study,the cooling rate was manipulated by quenching with water of different temperatures(30,60 and 100℃).Surface and internal residual stresses in the quenched 6061 aluminum alloy samples were measured using hole-drilling and crack compliance methods,respectively.Then,the processability of the quenched samples was evaluated at cryogenic temperatures.The mechanical properties of the as-aged samples were assessed,and microstructure evolution was analyzed.The surface residual stresses of samples W30℃,W60℃and W100℃is−178.7,−161.7 and−117.2 MPa,respectively along x-direction,respectively;and−191.2,−172.1 and−126.2 MPa,respectively along y-direction.The sample quenched in boiling water displaying the lowest residual stress(~34%and~60%reduction in the surface and core).The generation and distribution of quenching residual stress could be attributed to the lattice distortion gradient.Desirable plasticity was also exhibited in the samples with relatively low quenching cooling rates at cryogenic temperatures.The strengthes of the as-aged samples are 291.2 to 270.1 MPa as the quenching water temperature increase from 30℃to 100℃.Fine and homogeneous β"phases were observed in the as-aged sample quenched with boiling water due to the clusters and Guinier-Preston zones(GP zones)premature precipitated during quenching process.
基金supported by the ARDB,DRDO,New Delhi[Sanction Code:MSRB/TM/ARDB/GIA/19-20/044].
文摘Use of magnesium is the need of the hour due to its low density as well as its high strength-to-weight and stiffness-to-weight ratio etc.This study focuses on the effectiveness of liquid nitrogen(LN_(2))assisted cryogenic machining on the surface integrity(SI)characteristics of AZ91 magnesium alloy.Face milling using uncoated carbide inserts have been performed under liquid nitrogen(LN_(2))assisted cryogenic condition and compared with conventional(dry)milling.Experiments are performed using machining parameters in terms of cutting speeds of 325,475,625 m/min,feed rates of 0.05,0.1,0.15 mm/teeth and depth of cuts of 0.5,1,1.5 mm respectively.Most significant surface integrity characteristics such as surface roughness,microhardness,microstructure,and residual stresses have been investigated.Behaviour of SI characteristics with respect to milling parameters have been identified using statistical technique such as ANOVA and signal-to-noise(S/N)ratio plots.Additionally,the multi criteria decision making(MCDM)techniques such as additive ratio assessment method(ARAS)and complex proportional assessment(COPRAS)have been utilized to identify the optimal conditions for milling AZ91 magnesium alloy under both dry and cryogenic conditions.Use of LN_(2)during machining,resulted in reduction in machining temperature by upto 29%with a temperature drop from 251.2℃under dry condition to 178.5℃in cryogenic condition.Results showed the advantage of performing cryogenic milling in improving the surface integrity to a significant extent.Cryogenic machining considerably minimized the roughness by upto 28%and maximised the microhardness by upto 23%,when compared to dry machining.Cutting speed has caused significant impact on surface roughness(95.33%-dry,92.92%-cryogenic)and surface microhardness(80.33%-dry,82.15%-cryogenic).Due to the reduction in machining temperature,cryogenic condition resulted in compressive residual stresses(maximumσ║=-113 MPa)on the alloy surface.Results indicate no harm to alloy microstructure in both conditions,with no alterations to grain integrity and minimal reduction in the average grain sizes in the near machined area,when compared to before machined(base material)surface.The MCDM approach namely ARAS and COPRAS resulted in identical results,with the optimal condition being cutting speed of 625 m/min,a feed rate of 0.05 mm/teeth,and a depth of cut of 0.5 mm for both dry and cryogenic environments.
