Effects of nano TiN addition on the microstructure and mechanical properties of TiC based steel bonded carbides

TiC based steel bonded carbides with the addition of nano TiN were prepared by vacuum sintering techniques.The microstructure was investigated using scanning electron microscopy（SEM） and transmission electron microscopy（TEM）,and the mechanical properties,such as bending strength,impact toughness,hardness,and density,were measured.The results indicate that the grain size becomes small and there is uniformity in the steel bonded carbide with nano addition;several smaller carbide particles are also found to be inlaid in the rim of the larger carbide grains and prevent the coalescence of TiC grains.The smaller and larger carbide grains joint firmly,and then the reduction of the average size of the grains leads to the increase in the mechanical properties of the steel bonded carbides with nano addition.But the mechanical properties do not increase monotonously with an increase in nano addition.When the nano TiN addition accounts for 6-8 wt.% of the amount of steel bonded carbides,the mechanical properties reach the maximum values and then decrease with further increase in nano TiN addition.

Complex Precipitation Mechanism of Ti-Nb-V Microalloyed Bainitic Base High Strength Steel

The addition of high Ti（>0.1%） in microalloyed bainitic high strength steel was designed, and the precipitation morphology of steels with different Ti, Nb, and V contents was studied by utilizing transmission electron microscopy（TEM）. Based on the classical nucleation-crystal growth theory and the Johnson-Mehl-Avrami equation, the precipitation thermodynamic and kinetic model of second phase particles in austenite was established in the form of（Nbx,Vy,Tiz）C, and the complex precipitation mechanism of second phase particles was emphatically studied. The experimental results show that the complex precipitation particles could be divided into two categories: the coarser particles with about 100 nm grain size and the independent complex precipitation particles in the form of（Nb,V,Ti）C with 35-50 nm grain size. The latter has a better precipitation strengthening effect, and the calculated PTT curve shows a typical "C" shape. When the deformed storage energy is 3 820 J?mol-1, the fastest precipitation temperature of calculated PTT curve is 925 °C, and the calculated result is essentially consistent with experimental values. The increase of Ti content increased the nose point temperature and expanded the range of fastest precipitation temperature.

Seismic performance evaluation of steel frame-steel plate shear walls system based on the capacity spectrum method

This paper presents some methods that the standard acceleration design response spectra derived from the present China code for seismic design of buildings are transformed into the seismic demand spectra, and that the base shear force-roof displacement curve of structure is converted to the capacity spectrum of an equivalent single-degree-of-freedom （SDOF） system. The capacity spectrum method （CSM） is programmed by means of MATLABT.0 computer language. A dual lateral force resisting system of 10-story steel frame-steel plate shear walls （SPSW） is designed according to the corresponding China design codes. The base shear force-roof displacement curve of structure subjected to the monotonic increasing lateral inverse triangular load is obtained by applying the equivalent strip model to stimulate SPSW and by using the finite element analysis software SAP2000 to make Pushover analysis. The seismic performance of this dual system subjected to three different conditions, i.e. the 8-intensity frequently occurred earthquake, fortification earthquake and seldom occurred earthquake, is evaluated by CSM program. The excessive safety of steel frame-SPSW system designed according to the present China design codes is pointed out and a new design method is suggested.

Wear and corrosion resistance of laser-cladded Fe-based composite coatings on AISI 4130 steel

The wear and corrosion resistance of Fe_（72.2）Cr_（16.8）Ni_（7.3）Mo_（1.6）Mn_（0.7）C_（0.2）Si_（1.2） and Fe_（77.3）Cr_（15.8）Ni_（3.9）Mo_（1.1）Mn_（0.5）C_（0.2）Si_（1.2） coatings laser-cladded on AISI 4130 steel were studied.The coatings possess excellent wear and corrosion resistance despite the absence of expensive yttrium,tungsten,and cobalt and very little molybdenum.The microstructure mainly consists of dendrites and eutectic phases,such as duplex（γ＋α）-Fe and the Fe–Cr（Ni）solid solution,confirmed via energy dispersive spectrometry and X-ray diffraction.The cladded Fe-based coatings have lower coefficients of friction,and narrower and shallower wear tracks than the substrate without the cladding,and the main wear mechanism is mild abrasive wear.Electrochemical test results suggest that the soft Fe_（72.2）Cr_（16.8）Ni_（7.3）Mo_（1.6）Mn_（0.7）C_（0.2）Si_（1.2） coating with high Cr and Ni concentrations has high passivation resistance,low corrosion current,and positive corrosion potential,providing a better protective barrier layer to the AISI 4130 steel against corrosion.

Peak displacement patterns for the performance-based seismic design of steel eccentrically braced frames

Performance-based seismic design(PBSD) aims to assess structures at different damage states. Since damage can be directly associated to displacements, seismic design with consideration of displacement seems to be logical. In this study, simple formulae to estimate the peak floor displacement patterns of eccentrically braced frames(EBFs) at different performance levels subjected to earthquake ground motions are proposed. These formulae are applicable in a PBSD and especially in direct displacement-based design(DDBD). Parametric study is conducted on a group of 30 EBFs under a set of 15 far field and near field accelerograms which they scaled to different amplitudes to adapt various performance levels. The results of thousands of nonlinear dynamic analyses of EBFs have been post-processed by nonlinear regression analysis in order to recognize the major parameters that influence the peak displacement pattern of these frames. Results show that suggested displacement patterns have relatively good agreement with those acquired by an exact nonlinear dynamic analysis.

Mechanical Properties of Powder Based Steel used as Backing Plate in Heavy Duty Brake Pad Manufacturing

The aims of the present study is to develop a powder based steel used as backing plate for heavy duty brake pad applications. Three powder based back plate steel compositions namely B1 (C- 0.3, Cu – 1.5, P -0.3, Fe – 97.9), B2 (C- 0.1, Cu – 2.5, SiC-1, Fe – 96.4) and B3(C- 0.5, Cu – 2.5, SiC-1, Fe – 96.0) were prepared using a hot powder preform forging technique. The forged samples are of (25× 50×10 mm3) dimensions. These samples were hot rolled and annealed to relieve the residual stresses. These samples were characterized in terms of microstructure, porosity content/densification, hardness and tensile properties. Densification as high near to theoretical density has been realized. Hot powder preform forging using closed die showed better densification. Rolled and annealed microstructure showed lesser porosity content than the forged one. Phosphorous causes hardening of ferrite in solid solution with iron. Compositions B1, showed reasonable elongation and it improved further on annealing. It was observed in this present investigation that, the addition, such as SiC and Cu caused increase in strength. Steel developed in the investigation are used as powder based backing plate in Manufacturing of iron based brake pads used in heavy duty applications.

Microstructures and properties of Co-based alloy coatings prepared on surface of H13 steel

The Co-based alloy coatings had been prepared by laser cladding and vacuum fusion sintering. Microstructures of the coatings were investigated and the performance of thermal cycling was also tested using scanning electron microscopy （ SEM） and X-ray diffraction （ XRD ）. The results show that the coatings and substrates combine well. The main phase compositions of laser cladding coating are T-Co, Cr23 C6 and Ni2 9 Cro. 7 Feo. 36, while vacuum fusion sintering coating consists of Co, Cr7 C3, and Ni2.9 Cro. 7 Feo. 36. After thermal cycling, the minimum hot cracking width of laser cladding coating is 14 μm; moreover, laser cladding coating maintains high hardness and hot-cracking susceptibility. Those are beneficial to high temperature wear resistance of hot work dies.

Dephosphorization Thermodynamics of Crude Steel Using CaO-Based Flux

The experiments were carried out at 1 175-1 450 ℃ to study the phosphorus distribution ratio between molten Ca O-based slags and carbon saturated hot metal. The phosphate capacity of the slags and the activity coefficient of PO2. 5were calculated from the phosphorus distribution ratio. The effect of addition of Ca F2 and / or Ca Cl2 on the thermodynamic properties of slags was discussed. The correlation of optical basicity with phosphate capacity of slags was studied,and the dephosphorization ability of Ca O-based fluxes with various additives was compared with the results from different studies.

Vacuum Brazing of TiAl Based Alloy with 40Cr Steel

The vacuum brazing of TiAl based alloy with 40Cr steel was investigated using Ag-Cu-Ti filler metal. The experimental results show that the Ag, Cu, Ti atoms in the filler metal and the base metal inter-diffuse toward each other during brazing and react at the interface to form an inter-metallic AlCu 2Ti compound which joins two parts to produce a brazing joint with higher strength.

A new methodology for energy-based seismic design of steel moment frames

A procedure is proposed whereby input and hysteretic energy spectra developed for single-degree-of-freedom （SDOF） systems are applied to multi-degree-of-freedom （MDOF） steel moment resisting frames. The proposed procedure is verified using four frames, viz., frame with three-, five-, seven- and nine-stories, each of which is subjected to the fault- normal and fault-parallel components of three actual earthquakes. A very good estimate for the three- and five-story frames, and a reasonably acceptable estimate for the seven-, and nine-story frames, have been obtained. A method for distributing the hysteretic energy over the frame height is also proposed. This distribution scheme allows for the determination of the energy demand component of a proposed energy-based seismic design （EBSD） procedure for each story. To address the capacity component of EBSD, a story-wise optimization design procedure is developed by utilizing the energy dissipating capacity from plastic hinge formation/rotation for these moment frames. The proposed EBSD procedure is demonstrated in the design of a three-story one-bay steel moment frame.

Laser Shock Processing of an Austenitic Stainless Steel and a Nickel-base Superalloy

An austenitic stainless steel 1Cr18Ni9Ti and a solid solution-strengthened Ni-base superalloy GH30 were shock processed using a Q-switched pulsed Nd-glass laser. Microstructure, hardness and residual stress of the laser shock processed surface were investigated as functions of laser processing parameters. Results show that high density of dislocations and fine deformation twins are produced in the laser shock processed surface layers in both the austenitic stainless steel and the nickel-base superalloy. Extensive strain-induced martensite was also observed in the laser shock processed zone of the austenitic steel. The hardness of the laser shock processed surface was significantly enhanced and compressive stress as high as 400 MPa was produced in the laser shock processed surface.

Bauxite Based Bricks for Steel Ladle

1 Scope This standard specifies the classification, technical requirements, test methods, inspection rules, packing, marking, transportation, storage, and quality certificate of bauxite based bricks for steel ladle linings.

Development of ultra high strength special steels and wrought nickel base superalloys

Ultra-high strength special steels and wrought Ni-base superalloys are been ever increasingly applied in aircraft and aerospace,power generation,oil-gas and other industries.The development of those materials is driven by tougher working conditions,higher efficiency,environment consideration,resource limitation and cost reduction. This presentation will focus on the development of ultra high strength special steels and wrought Ni-base superalloys in aircraft industry. The examples of ultra-high strength steels include: (1) Ultra-high strength stainless steels for landing gear and other structures; (2)High speed and high temperature main shaft bearing steels; (3) Ultra-high strength steels for jet engine main shaft. New and modified Ni-base superalloys will be discussed by examples of (1 )Low cost,process-friendly superalloys with higher performance; (2)Modification of hard-to-processed superalloys. Future development of those materials will be addressed.

As-cast Medium Mn Steel with Nodular Carbide Modified by Y-base Heavy RE Compound

1.IntroductionMedium Mn steel was developed be-cause the wear resistance of Hadfield steel(Mn13)is poor under low or medium im-pact and extrusion abrasion[1-4].In theforegoing investigations[2-4]we found thatwith the increase of C content,theneedle-like and network carbide in mediumMn steel increased(as shown in Fig.1(a)and(c)).Although its wear resistance was largelyimproved,its impact toughness was greatlydecreased.In order to increase toughness,along-term high temperature heat-treatmentwas needed.But the treatment caused cracks

Stress Corrosion Cracking of Pressure Vessel Steel and Countermeasures by Titanium-Based & Cerium-Based Inhibitors in Subcritical Aqueous Environment

An overview of a severe kind of environmentally-assisted cracking-stress corrosion cracking (SCC) of pressure vessel steel (PVS),such as stainless steel 304, alloy 600,690 and other nickel-based alloys in subcritical (～300 ℃) aqueous environment was given. The mechanisms of SCC of metals under this inclement surrounding were briefly generalized. Herein,some pragmatic solutions to mitigate the SCC susceptibility and retard its propagation were presented. The titanium and cerium-based inhibitors addition countermeasure was highlighted.

Feasibility of 0.02% Nb-Based Microalloyed Steel for the Application of One-Step Quenching and Partitioning Heat Treatment

To attain an enhanced combination of mechanical properties for low alloyed steel, the current study has been made to fulfill that growing need in the industry. Its results are introduced within this paper. One step Quenching and Partitioning (Q&P) heat treatment has been applied on Niobium-based microalloyed steel alloy with 0.2 %C, in the form of 2 mm thickness sheets. The target of this study is to investigate the viability of applying that significantly recommended, results-wise, heat treatment on the highly well-suited alloy steel samples, to achieve the main target of enhanced properties. A single temperature of 275°C was used as quenching and Partitioning temperature. Four Partitioning periods (30, 200, 500, and 1000 Seconds) were used for soaking at the same temperature. The results were analyzed in the light of microstructural investigation and mechanical testing. All applied cycles did not enhance the strength but moderately improved the ductility and toughness, mainly caused by the slightly high soaking temperature used. Niobium impact of grain refining was apparent through all cycles. The cycle of 500 Seconds Partitioning time obtained optimum values at that particular temperature. The 1000 Seconds Cycle obtained the worst combination of properties. A set of recommendations are set. More research is required at this point, where a lower Partitioning temperature is advised. In the light of the applied combination of parameters, the Partitioning period at such temperature is advised to be between 500 and 1000 Seconds. A high probability that periods closer to 500 than 1000 Seconds will produce better results. More research is needed between those two values of Partitioning time to precisely determine the optimum time at that temperature on that specific alloy.

Hot corrosion behavior of Ni–16Cr–xAl based alloys in mixture of Na_2SO_4-NaCl at 600 ℃

The hot corrosion behaviors of Ni–16Cr–xAl（x=4.5%, 6.8%, 9.0%, mass fraction） based alloys in Na2SO4–25% NaCl molten salts at 600 °C were investigated. The effects of pre-oxidation and Al content on the resistance to hot corrosion were examined. The hot corrosion resistance of Ni–16Cr–xAl based alloy with Al addition from 4.5% to 9.0% increases with increasing Al content. The alloy with Al content of 9.0% shows the highest hot corrosion resistance among the examined alloys because more β–NiAl phases are obtained to sustain the Al2O3 scale repaired during hot corrosion. Pre-oxidized specimens have a superior hot corrosion resistance compared with the as-cast specimens, due to a protective oxide scale formed after pre-treatment.

Fracture Properties of Cement Composites Reinforced with Steel Polypropylene Hybrid Fibres

Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.

Seismic assessment of unanchored steel storage tanks by endurance time method

Liquid storage tanks are essential structures that are often located in residential and industrial areas; thus an assessment of their seismic performance is an important engineering issue. In this paper, the seismic response ofunanchored steel liquid storage tanks is investigated using the endurance time （ET） dynamic analysis procedure and compared to responses obtained for anchored tanks under actual ground motions and intensifying ET records. In most cases, the results from ground motions are properly obtained with negligible differences using ET records. It is observed that uplifting of the tank base, which is closely related to the tank aspect ratio, has the greatest significance in the responses of the tank and can be predicted with reasonable accuracy by using currently available ET records.

Comprehensive Utilization of Natural Magnesium-Containing Resources and the Development of MgO-Based Refractories

This paper presents the ways of comprehensive utilization of the natural magnesium containing resources and the trends of the MgO based refractories used in high temperature industries. In the first part, the uses and productions of metal Mg, sorel cement, Mg (OH) 2 fire retardant, light magnesium carbonate, light magnesia and magnesium sulphate are described. In the second part, the developments of MgO based refractories used in steelmaking process, nonferrous metallurgy, cement rotary kiln and waste melting furnace are described from some applied theories, including corrosion resistant and slaking resistant MgO CaO materials, chrome free bricks such as MgO CaO ZrO 2 , MgO MgO Al 2 O 3 , MgO MgO·Al 2 O 3 ZrO 2 , MgO MgO·Al 2 O 3 2MgO ·TiO 2 and MgO FeO·Al 2 O 3 , and MgO containing monolithic refractories etc.