Insights on advanced substrates for controllable fabrication of photoanodes toward efficient and stable photoelectrochemical water splitting

Conversion of solar energy into H_(2) by photoelectrochemical(PEC)water splitting is recognized as an ideal way to address the growing energy crisis and environmental issues.In a typical PEC cell,the construction of photoanodes is crucial to guarantee the high efficiency and stability of PEC reactions,which fundamentally rely on rationally designed semiconductors(as the active materials)and substrates(as the current collectors).In this review work,we start with a brief introduction of the roles of substrates in the PEC process.Then,we provide a systematic overview of representative strategies for the controlled fabrication of photoanodes on rationally designed substrates,including conductive glass,metal,sapphire,silicon,silicon carbide,and flexible substrates.Finally,some prospects concerning the challenges and research directions in this area are proposed.

Facile electrochemical surface-alloying and etching of Au wires to enable high-performance substrates for surface enhanced Raman scattering

Surface-enhanced Raman Spectroscopy(SERS)is a nondestructive technique for rapid detection of analytes even at the single-molecule level.However,highly sensitive and reliable SERS substrates are mostly fabricated with complex nanofabrication techniques,greatly restricting their practical applications.A convenient electrochemical method for transforming the surface of commercial gold wires/foils into silver-alloyed nanostructures is demonstrated in this report.Au substrates are treated with repetitive anodic and cathodic bias in an electrolyte of thiourea,in a one-pot one-step manner.X-rays absorption fine structure(XAFS)spectroscopy confirms that the AuAg alloy is induced at the surface.The unique AuAg alloyed surface nanostructures are particularly advantageous when served as SERS substrates,enabling a remarkably sensitive detection of Rhodamine B(a detection limit of 10^(-14)M,and uniform strong response throughout the substrates at 10^(-12)M).

Localized-states quantum confinement induced by roughness in CdMnTe/CdTe heterostructures grown on Si(111) substrates

This work shows that despite a lattice mismatch of almost 20%, CdMnTe/CdTe/CdMnTe heterostructures grown directly on Si(111) have surprisingly good optical emission properties. The investigated structures were grown by molecular beam epitaxy and characterized by scanning transmission electron microscopy, macro-and micro-photoluminescence. Low temperature macro-photoluminescence experiments indicate three emission bands which depend on the CdTe layer thickness and have different confinement characteristics. Temperature measurements reveal that the lower energy emission band (at 1.48 eV)is associated to defects and bound exciton states, while the main emission at 1.61 eV has a weak 2D character and the higher energy one at 1.71 eV has a well-defined (zero-dimensional, 0D) 0D nature. Micro-photoluminescence measurements show the existence of sharp and strongly circularly polarized (up to 40%) emission lines which can be related to the presence of Mn in the heterostructure. This result opens the possibility of producing photon sources with the typical spin control of the diluted magnetic semiconductors using the low-cost silicon technology.

Active tuning of anisotropic phonon polaritons in natural van der Waals crystals with negative permittivity substrates and its application in energy transport

Phonon polaritons(PhPs)exhibit directional in-plane propagation and ultralow losses in van der Waals(vdW)crystals,offering new possibilities for controlling the flow of light at the nanoscale.However,these PhPs,including their directional propagation,are inherently determined by the anisotropic crystal structure of the host materials.Although in-plane anisotropic PhPs can be manipulated by twisting engineering,such as twisting individual vdW slabs,dynamically adjusting their propagation presents a significant challenge.The limited application of the twisted bilayer structure in bare films further restricts its usage.In this study,we present a technique in which anisotropic PhPs supported by bare biaxial vdW slabs can be actively tuned by modifying their local dielectric environment.Excitingly,we predict that the iso-frequency contour of PhPs can be reoriented to enable propagation along forbidden directions when the crystal is placed on a substrate with a moderate negative permittivity.Besides,we systematically investigate the impact of polaritonic coupling on near-field radiative heat transfer(NFRHT)between heterostructures integrated with different substrates that have negative permittivity.Our main findings reveal that through the analysis of dispersion contour and photon transmission coefficient,the excitation and reorientation of the fundamental mode facilitate increased photon tunneling,thereby enhancing heat transfer between heterostructures.Conversely,the annihilation of the fundamental mode hinders heat transfer.Furthermore,we find the enhancement or suppression of radiative energy transport depends on the relative magnitude of the slab thickness and the vacuum gap width.Finally,the effect of negative permittivity substrates on NFRHT along the[001]crystalline direction ofα-MoO3 is considered.The spectral band where the excited fundamental mode resulting from the negative permittivity substrates is shifted to the first Reststrahlen Band(RB 1)ofα-MoO_(3) and is widened,resulting in more significant enhancement of heat flux from RB 1.We anticipate our results will motivate new direction for dynamical tunability of the PhPs in photonic devices.

Effects of thrombopoietin pre-treatment on peri-liver transplantation thrombocytopenia in a mouse model of cirrhosis with hypersplenism

BACKGROUND During cirrhosis,the liver is impaired and unable to synthesize and clear thrombopoietin properly.At the same time,the spleen assumes the function of hemofiltration and storage due to liver dysfunction,resulting in hypersplenism and excessive removal of platelets in the spleen,further reducing platelet count.When liver function is decompensated in cirrhotic patients,the decrease of thrombopoietin(TPO)synthesis is the main reason for the decrease of new platelet production.This change of TPO leads to thrombocytopenia and bleeding tendency in cirrhotic patients with hypersplenism.AIM To investigate the clinical efficacy of recombinant human TPO(rhTPO)in the treatment of perioperative thrombocytopenia during liver transplantation in cirrhotic mice with hypersplenism.METHODS C57BL/6J mice and TPO receptor-deficient mice were used to establish models of cirrhosis with hypersplenism.Subsequently,these mice underwent orthotopic liver transplantation(OLT).The mice in the experimental group were given rhTPO treatment for 3 consecutive days before surgery and 5 consecutive days after surgery,while the mice in the control group received the same dose of saline at the same frequency.Differences in liver function and platelet counts were determined between the experimental and control groups.Enzyme-linked immunosorbent assay was used to assess the expression of TPO and TPO receptor(c-Mpl)in the blood.RESULTS Preoperative administration of rhTPO significantly improved peri-OLT thrombocytopenia in mice with cirrhosis and hypersplenism.Blocking the expression of TPO receptors exacerbated peri-OLT thrombocytopenia.The concentration of TPO decreased while the concentration of c-Mpl increased in compensation in the mouse model of cirrhosis with hypersplenism.TPO pre-treatment significantly increased the postoperative TPO concentration in mice,which in turn led to a decrease in the c-Mpl concentration.TPO pre-treatment also significantly enhanced the Janus kinase(Jak)/signal transducers and activators of transcription pathway protein expressions in bone marrow stem cells of the C57BL/6J mice.Moreover,the administration of TPO,both before and after surgery,regulated the levels of biochemical indicators,such as alanine aminotransferase,alkaline phosphatase,and aspartate aminotransferase in the C57BL/6J mice.CONCLUSION Pre-treatment with TPO not only exhibited therapeutic effects on perioperative thrombocytopenia in the mice with cirrhosis and hypersplenism,who underwent liver transplantation but also significantly enhanced the perioperative liver function.

Evaluation of Different Substrates Compositions for Acclimatization of Tissue Culture Taro Plantlets in a Propagator

Taro is cultivated in most Regions of Cameroon and it is affected by taro leaf blight disease since 2010 which has decreased its production. Lack of disease-free planting materials has been a main problem to farmers. This study was carried out at International Institute of Tropical Agriculture (IITA) Yaounde and Institute of Agricultural Research for Development (IRAD) Bambui to assess different substrates for acclimatization of tissue culture taro plantlets in apropagator. No information is available on acclimatization of Cameroonian taro plantlets in different substrates. Taro plantlets from tissue culture were acclimatised in a propagator for six weeks under different substrates, the first substrate consisted of sterile three parts of soil and one part of river sand mixed together (3:1), the second substrate consisted of sterile two parts of soil and two parts of river sand mixed together (2:2), the third substrate consisted of sterile two parts of soil, one part of rice husk and one part of river sand mixed together (2:1:1) and the fourth substrate consisted of sterile one part of soil and three parts of river sand mixed together (1:3). After acclimatisation of the different taroplantlets (Dark green petiole with small leaves (L1), Red petiole with small leaves (L2), Light green petiole with large leaves (L3) and Light green petiole with small leaves (L4) in these four substrates, it was observed that the best growth rate of plant was recorded on substrate sand + soil (1:3). The other substrates showed moderate growth of plants. Substrate sand + soil (1:3) can be recommended for acclimatization of Cameroonian taro plantlets.

Structure of Cu-Phthalocyanine Vacuum Deposited on Inclined Glass Substrates

Cu-phthalocyanine is widely studied as a hole-transport layer in organic electronic devices. Since Cu-phthalocyanine is a molecular solid, the crystal structure depends on a circumstance to a great extent. Vacuum deposited layers were known to consist of two consecutive layers. In this article, Cu-phthalocyanine was deposited on the glass substrate inclined at several angles. The thickness of the first layer was found to be dependent on the substrate angle.

Performance of Two Food Substrates in the Mass Rearing of Bactrocera dorsalis Hendel (Diptera: Tephritidae)

The fruit fly Bactrocera dorsalis Hendel is a major constraint to mango production in Burkina Faso. The objective of this study was to evaluate the performance of two types of food substrates in optimizing the mass rearing of B. dorsalis larvae. For this purpose, 200 eggs of B. dorsalis were divided into four batches of 50 eggs and incubated in Petri dishes containing the different food substrates (Diet 1 and Diet 2). This method was used to evaluate the rate and duration of egg hatching, as well as the development time of the different larval stages. In addition, 1200 pupae divided into four batches of 300 pupae, contained in PVC tubes, were placed inside the rearing cages to monitor the emergence of B. dorsalis. Ten pairs of B. dorsalis were placed in rearing cages and fed with Enzymatic Yeast Hydrolysate and sugar to evaluate the fecundity of female flies and the survival of both sexes. The developmental cycle length in Diet 1 and Diet 2 was 23.03 days and 23.24 days, respectively. Fecundity duration ranged from 57.75 ± 2.29 to 109.81 ± 3.81 days for females from Diet 1 and Diet 2, respectively. The pupal hatching rate varied significantly (P B. dorsalis, but the spawning index was 4 times higher with Diet 1. Most of the components of Diet 1 are available on the local market and are cheaper. Thus, we recommend the use of Diet 1 for B. dorsalis larvae mass rearing.

High-temperature annealing of(201)β-Ga_(2)O_(3) substrates for reducing structural defects after diamond sawing

A commercial epi-ready(201)β-Ga_(2)O_(3) wafer was investigated upon diamond sawing into pieces measuring 2.5×3 mm^(2).The defect structure and crystallinity in the cut samples has been studied by X-ray diffraction and a selective wet etching technique.The density of defects was estimated from the average value of etch pits calculated,including near-edge regions,and was obtained close to 109 cm^(-2).Blocks with lattice orientation deviated by angles of 1-3 arcmin,as well as non-stoichiometric fractions with a relative strain about(1.0-1.5)×10^(-4)in the[201]direction,were found.Crystal perfection was shown to decrease significantly towards the cutting lines of the samples.To reduce the number of structural defects and increase the crystal perfection of the samples via increasing defect motion mobility,the thermal annealing was employed.Polygonization and formation of a mosaic structure coupled with dislocation wall appearance upon 3 h of annealing at 1100℃ was observed.The fractions characterized by non-stoichiometry phases and the block deviation disappeared.The annealing for 11 h improved the homogeneity and perfection in the crystals.The average density of the etch pits dropped down significantly to 8×10^(6) cm^(-2).

11.2 W/mm power density AlGaN/GaN high electron-mobility transistors on a GaN substrate

In this letter,high power density AlGaN/GaN high electron-mobility transistors(HEMTs)on a freestanding GaN substrate are reported.An asymmetricΓ-shaped 500-nm gate with a field plate of 650 nm is introduced to improve microwave power performance.The breakdown voltage(BV)is increased to more than 200 V for the fabricated device with gate-to-source and gate-to-drain distances of 1.08 and 2.92μm.A record continuous-wave power density of 11.2 W/mm@10 GHz is realized with a drain bias of 70 V.The maximum oscillation frequency(f_(max))and unity current gain cut-off frequency(f_(t))of the AlGaN/GaN HEMTs exceed 30 and 20 GHz,respectively.The results demonstrate the potential of AlGaN/GaN HEMTs on freestanding GaN substrates for microwave power applications.

Evolution of microstructure, stress and dislocation of AlN thick film on nanopatterned sapphire substrates by hydride vapor phase epitaxy

A crack-free AlN film with 4.5 μm thickness was grown on a 2-inch hole-type nano-patterned sapphire substrates(NPSSs) by hydride vapor phase epitaxy(HVPE). The coalescence, stress evolution, and dislocation annihilation mechanisms in the AlN layer have been investigated. The large voids located on the pattern region were caused by the undesirable parasitic crystallites grown on the sidewalls of the nano-pattern in the early growth stage. The coalescence of the c-plane AlN was hindered by these three-fold crystallites and the special triangle void appeared. The cross-sectional Raman line scan was used to characterize the change of stress with film thickness, which corresponds to the characteristics of different growth stages of AlN. Threading dislocations(TDs) mainly originate from the boundary between misaligned crystallites and the c-plane AlN and the coalescence of two adjacent c-plane AlN crystals, rather than the interface between sapphire and AlN.

Effects of Scarification and Substrates on Seed Germination Quality for Domestication of Stereospermum kunthianum(Bignoniaceae)

The demand for medicinal plants at the origin of phyto-drugs,like all ethnobotanical plants,threatens their existence today.The aim of this work was to determine suitable methods for optimizing the possibilities of regenerating Stereospermum kunthianum.To achieve this objective,3 levels of mechanical scarification(light scarification,medium scarification and deep scarification)were applied to the seeds of this species using a rough instrument,and 5 days after germination,the seedlings were transplanted into 5 types of substrate to study their effects on seedling growth.The length of the seedlings was measured using a graduated ruler.The results obtained showed that the best latency time was 2 days for average seed scarifications.The highest germination half-time was 4.00±0.06 days observed for average seed scarification,the highest germination speed was 22.50±1.00 and the highest germination rate was 100.00%±0.00%for average scarification.The homogeneous substrate mixes black earth/woodsilk and Fine sand/woodsilk were more effective for seedling growth(1.9 cm/day in the juvenile state)and development.Medium seed scarification is the most effective method for regenerating Stereospermum kunthianum,and the black earth/wood shavings substrate mix is the best for its cultivation.

A Pore-Forming Strategy Toward Porous Carbon-Based Substrates for High Performance Flexible Lithium Metal Full Batteries

Self-standing carbon-based substrates with satisfied structural stability and property adjustability have promising applications in flexible lithium(Li)metal batteries(FLMBs).Current strategies for modifying carbon materials are normally carried out on powder carbon,and very few of them are suitable for self-standing carbon substrates.Herein,a pore-forming strategy based on the redox chemistry of metallic oxide nanodots is developed to prepare two porous carbon substrates for anode and cathode.Starting with cotton cloth,the resulting hollow carbon fibers substrate with nanopores effectively prevents from Li dendrites formation and large volume change in lithium metal anode(LMA).Simulations indicate that the porous structure leads to homogeneous ion flux,Li-ion concentration,and electric field during Li deposition.Li symmetrical cell based on this substrate remains stable for 8300 h with an ultralow voltage hysteresis of 9 mV.Via a similar route,porous carbon cloth substrate is obtained for subsequently seeding V_(2)O_(5)nanowires to prepare the cathode.The assembled FLMBs pouch cell delivers a capacity of 8.2 mAh with a high capacity retention of~100%even under dramatic deformation.The demonstrated strategy has far-reaching potential in preparing free-standing porous carbon-based materials for flexible energy storage devices.

Influence of substrate effect on near-field radiative modulator based on biaxial hyperbolic materials

Relative rotation between the emitter and receiver could effectively modulate the near-field radiative heat transfer(NFRHT)in anisotropic media.Due to the strong in-plane anisotropy,natural hyperbolic materials can be used to construct near-field radiative modulators with excellent modulation effects.However,in practical applications,natural hyperbolic materials need to be deposited on the substrate,and the influence of substrate on modulation effect has not been studied yet.In this work,we investigate the influence of substrate effect on near-field radiative modulator based onα-MoO_(3).The results show that compared to the situation without a substrate,the presence of both lossless and lossy substrate will reduce the modulation contrast(MC)for different film thicknesses.When the real or imaginary component of the substrate permittivity increases,the mismatch of hyperbolic phonon polaritons(HPPs)weakens,resulting in a reduction in MC.By reducing the real and imaginary components of substrate permittivity,the MC can be significantly improved,reaching 4.64 forε_(s)=3 at t=10 nm.This work indicates that choosing a substrate with a smaller permittivity helps to achieve a better modulation effect,and provides guidance for the application of natural hyperbolic materials in the near-field radiative modulator.

Enhanced resonance frequency in Co2FeAl thin film with different thicknesses grown on flexible graphene substrate

The flexible materials exhibit more favorable properties than most rigid substrates in flexibility,weight saving,mechanical reliability,and excellent environmental toughness.Particularly,flexible graphene film with unique mechanical properties was extensively explored in high frequency devices.Herein,we report the characteristics of structure and magnetic properties at high frequency of Co2FeAl thin film with different thicknesses grown on flexible graphene substrate at room temperature.The exciting finding for the columnar structure of Co2FeAl thin film lays the foundation for excellent high frequency property of Co2FeAl/flexible graphene structure.In-plane magnetic anisotropy field varying with increasing thickness of Co2FeAl thin film can be obtained by measurement of ferromagnetic resonance,which can be ascribed to the enhancement of crystallinity and the increase of grain size.Meanwhile,the resonance frequency which can be achieved by the measurement of vector network analyzer with the microstrip method increases with increasing thickness of Co2FeAl thin film.Moreover,in our case with graphene film,the resonance magnetic field is quite stable though folded for twenty cycles,which demonstrates that good flexibility of graphene film and the stability of high frequency magnetic property of Co2FeAl thin film grown on flexible graphene substrate.These results are promising for the design of microwave devices and wireless communication equipment.

Recess-free enhancement-mode AlGaN/GaN RF HEMTs on Si substrate

Enhancement-mode(E-mode)GaN-on-Si radio-frequency(RF)high-electron-mobility transistors(HEMTs)were fabri-cated on an ultrathin-barrier(UTB)AlGaN(<6 nm)/GaN heterostructure featuring a naturally depleted 2-D electron gas(2DEG)channel.The fabricated E-mode HEMTs exhibit a relatively high threshold voltage(VTH)of+1.1 V with good uniformity.A maxi-mum current/power gain cut-off frequency(fT/fMAX)of 31.3/99.6 GHz with a power added efficiency(PAE)of 52.47%and an out-put power density(Pout)of 1.0 W/mm at 3.5 GHz were achieved on the fabricated E-mode HEMTs with 1-μm gate and Au-free ohmic contact.

Facile SERS screening of melamine in bovine milk with 2D printed AgNPs/glass fabric filter paper as the flexible substrate

Melamine is one of the most frequently detected adulterants in dairy products.The current study proposes a surface-enhanced Raman spectroscopy(SERS)-based analytical tool for fast and reliable screening of melamine in bovine milk.A hand-held Raman spectrometer was used in conjunction with a substrate composed of silver nanoparticles(AgNPs)that was 2D printed onto glass fiber(GF)filter paper.Under optimized conditions,a sensitive and fingerprint-like signal at 674 cm^(-1) was obtained.The AgNPs/GF substrate exhibited high sensitivity to melamine in milk down to 1.9498×10^(-5)mg/mL,which is well below the USA and EU safety limits(2.5×10^(-3)mg/mL).Remarkably,the proposed technology was also highly reproducible,showing spot-to-spot and block-to-block variations below 3.3%and 4.9%at 674 cm^(-1) in Raman intensity,respectively.The characteristic peak intensity and concentration of melamine showed an acceptable linear relationship(R^(2)=0.9909)within the range of 0.0001-1 mg/mL.Overall,the method established in this study can provide an efficient and effective method for the quantitative target screening and detection of melamine in dairy products.

Split Addition of Nitrogen-Rich Substrate at Thermophilic and Mesophilic Stages of Composting: Effect on Green House Gases Emission and Quality of Compost

Composting as a solution to the increasing generation of municipal solid waste (MSW), also contribute to GHGs emission when not controlled and could lack some basic nutrients, especially nitrogen. This study assessed the split-additions of nitrogen-rich substrate to composting materials and their effect on GHGs emissions as well as the quality of the composts. Nitrogen-rich substrates formulated from pig and goat manure were co-composted with MSW for a 12-weeks period by split adding at mesophilic (˚C) and thermophilic (>50˚C) stages in five different treatments. Representative samples from the compost were taken from each treatment for physicochemical, heavy metals and bacteriological analysis. In-situ CH4, CO2, N2O gas emissions were also analyzed weekly during composting. It was observed that all the treatments showed significant organic matter decomposition, reaching thermophilic temperatures in the first week of composting. The absence affects the suitable agronomic properties. All nitrogen-rich substrate applied at thermophilic stage (Treatment two) recorded the highest N, P and K concentrations of 1.34%, 0.97% and 2.45%, respectively with highest nitrogen retention. In terms of GHG emissions, CO2 was highest at the thermophilic stage when N-rich substrate was added in all treatment, while CH4 was highest in the mesophilic stage with N-rich substrate addition. N2O showed no specific trend in the treatments. Split addition of the N-rich substrate for co-composting of MSW produced compost which is stable, has less nutrient loss and low GHG emissions. Split addition of a nitrogen-rich substrate could be an option for increasing the fertilizer value of MSW compost.

Effect of substrate temperature and oxygen plasma treatment on the properties of magnetron-sputtered CdS for solar cell applications

Cadmium sulfide(CdS)is an n-type semiconductor with excellent electrical conductivity that is widely used as an electron transport material(ETM)in solar cells.At present,numerous methods for preparing CdS thin films have emerged,among which magnetron sputtering(MS)is one of the most commonly used vacuum techniques.For this type of technique,the substrate temperature is one of the key deposition parameters that affects the interfacial properties between the target film and substrate,determining the specific growth habits of the films.Herein,the effect of substrate temperature on the microstructure and electrical properties of magnetron-sputtered CdS(MS-CdS)films was studied and applied for the first time in hydrothermally deposited antimony selenosulfide(Sb_(2)(S,Se)_(3))solar cells.Adjusting the substrate temperature not only results in the design of the flat and dense film with enhanced crystallinity but also leads to the formation of an energy level arrangement with a Sb_(2)(S,Se)_(3)layer that is more favorable for electron transfer.In addition,we developed an oxygen plasma treatment for CdS,reducing the parasitic absorption of the device and resulting in an increase in the short-circuit current density of the solar cell.This study demonstrates the feasibility of MS-CdS in the fabrication of hydrothermal Sb_(2)(S,Se)_(3)solar cells and provides interface optimization strategies to improve device performance.

Strained-Si pMOSFETs on Very Thin Virtual SiGe Substrates

Strained-Si pMOSFETs on very thin relaxed virtua l SiGe substrates are presented.The 240nm relaxed virtual Si 0.8 Ge 0.2 layer on 100nm low-temperature Si(LT-Si) is grown on Si(100) substrates by molecular beam epitaxy.LT-Si buffer layer is used to release stress of the SiGe layer so as to make it relaxed.DCXRD,AFM,and TEM measurements indicate that the strain relaxed degree of SiGe layer is 85%,RMS roughness is 1.02nm,and threading dislocation density is at most 107cm -2 .At room temperature,a maximum hole mobility of strained-Si pMOSFET is 140cm2/(V·s).Device performance is comparable to that of devices achieved on several microns thick relaxed virtual SiGe substrates.