Influence of nanosized magnesia on the hydration of borehole-sealing cements prepared using different methods

Gas drainage is an efective technology for gas control in coal mines.A high borehole-sealing quality is the fundamental precondition for efcient gas drainage.The expansibilities of cement pastes used in borehole-sealing processes are critical for the borehole-sealing efect.Nanosized magnesia expansive agents are used to improve the expansibilities of cement pastes and improve the borehole-sealing efect.Nuclear magnetic resonance spectrometry and scanning electron microscopy were adopted to study the efects of nanosized magnesia on the hydration of borehole-sealing cements used with diferent preparation methods.The results showed that an increase in the mass fraction of the nanosized magnesia promoted cement hydration,and the mass fraction was positively correlated with the promotion efect.The use of diferent preparation methods did not change the water-phase distribution in the cement.When using the wet-mixing preparation method,nanosized magnesia promoted the induction,acceleration,and deceleration periods of hydration;when using the dry-mixing preparation method,the nanosized magnesia promoted the induction period of cement hydration,and the promotion efect was less obvious than that seen when using the wet-mixing method.When using the wet-mixing preparation method,the nanosized magnesia was uniformly dispersed,thus enlarging the surface area of the reaction,which provided more nucleation sites for the hydration products of the cement and therefore accelerated the hydration reaction.When using the dry-mixing preparation method,the nanosized magnesia powders were dispersed nonuniformly and aggregated.Under these conditions,only a few nanosized magnesia particles on the surfaces of the aggregated clusters took part in hydration,so only a small number of nucleation sites were provided for the hydration products of cement.This led to inconsistent hydration of cement pastes prepared using the dry-mixing method.The surface porosity of the cement prepared with the wet-mixing preparation method frst decreased and then increased with increases in the mass fraction of the nanosized magnesia.The cement surface exhibited compact hydration products and few pores,and the surface was relatively smooth.In comparison,the surface porosity of the cement prepared using the dry-mixing method fuctuated with increasing mass fraction of the nanosized magnesia,resulting in a rough cement surface and microfractures on some surfaces.The two preparation methods both reduced the surface porosity of the cement.The wet-mixing preparation was more efective and consistent in improving the compactness of the cement than the dry-mixing preparation.These results provide important guidance on the addition of nanosized magnesia in borehole-sealing engineering and the selection of cement preparation methods,and they also lay a solid foundation for realizing safe and efcient gas drainage.

Microstructures and properties of Al_2O_3 dispersion-strengthened copper alloys prepared through different methods

Al2O3 dispersion copper alloy powder was prepared by intemal oxidation, and three consolidation methods--high-velocity compaction （HVC）, hot pressing （HP）, and hot extrusion （HE）--were used to prepare Al2O3 dispersion-strengthened copper （Cu-Al2O3） alloys. The microstructures and properties of these alloys were investigated and compared. The results show that the alloys prepared by the HP and HE methods exhibited the coarsest and finest grain sizes, respectively. The alloy prepared by the HVC method exhibited the lowest relative density （98.3% vs. 99.5% for HP and 100% for HE）, which resulted in the lowest electrical conductivity （81% IACS vs. 86% IACS for HP and 87% IACS for HE）. However, this alloy also exhibited the highest hardness （77 HRB vs. 69 HRB for HP and 70 HRB for HE）, the highest compressive strength （443 MPa vs. 386 MPa for I/P and 378 MPa for HE）, and the best hardness retention among the investigated alloys. The results illustrate that the alloy prepared by the HVC method exhibits high softening temperature and good mechanical properties at high temperatures, which imply long service life when used as spot-welding electrodes.

Characterization and catalytic behavior of Na-W-Mn-Zr-S-P/SiO_2 prepared by different methods in oxidative coupling of methane

Na-W-Mn-Zr-S-P/SiO2 catalysts for oxidative coupling of methane （OCM） were prepared by incipient wetness impregnation, sol-gel and mixture slurry methods. The catalyst prepared by mixture slurry method showed the best catalytic performance among all samples. In addition, the effects of different addition sequences of Na, W, Mn, Zr, S and P on the catalytic performance were studied. The absence of Na before the addition of Mn and Zr in the catalysts preparation depressed the formation of the active phases of Mn2O3 and ZrO2 and decreased the activities of the catalysts significantly.

Difference among the quality indices,chemical composition and frying performance of galangal flavored sunflower oil prepared by three methods

Flavored vegetable oils have attracted more and more attentions from consumers and researchers due to their high oxidative stability and sensory quality.In the present study,the quality indices,chemical composition and frying performance of galangal flavored sunflower oil prepared by infusion method(GFSO-I),combination pressing method(GFSO-C)and direct addition method(GFSO-A)were investigated.The results displayed that the preparation time,the levels for the acid value(AV),peroxide value(PV),p-anisidine value(AnV),total oxidation value(TOTOX),and the values for total polar compounds(TPC),thiobarbituric acid(TBA),K232 and K268 of GFSO-C were prominently low(P<0.05),compared with that of GFSO-I and GFSO-A,while the fatty acid composition of them were similar.In the frying of Chinese Maye(tradional Chinese food,fried dough stick)at 180°C for 30 h,the values for TPC,TBA,K232 and K268,polymer,viscosity and b*of GFSO-C were obviously low(P<0.05),while the value for L*was obviously high(P<0.05),compared with that of GFSO-I and GFSO-A.In the sensory evaluation,the flavor,taste,crispness and overall acceptance of Chinese Maye fried by GFSO-C were better than that of Chinese Maye fried by GFSO-I and GFSO-A.Consequently,GFSO-C is more suitable for cooking,and the combination pressing method is optimal for industrial production of GFSO.

Plastic Deformation of Nano-TiO_2 Ceramics Prepared by Different Methods

The comparative study of the tensile plastic deformation of nano(n)-TiO2 ceramic prepared byphysical gas condensation (P) and chemical hydrolysis precipitation (C) methods was conductedby a gas pressure forming technique at 750~800℃. The results show that n-TiO2 (P) possessesexcellent property of tensile pIastic deformation comparing with n-TiO2(C). The reason for thisis attributed to the surface cleanness and soft agglomeration of n-TiO2 (P) particfe prepared inreIatively cIean vacuum condition.

Preparation methods,biological activities,and potential applications of marine algae oligosaccharides:a review

Marine algae are valuable sources of health-promoting molecules that have been consumed by Asians for decades.Among aquatic flora,marine algae stand out in terms of high content of marine algae polysaccharides(MAP)such as carrageenan,alginate,fucoidan,laminaran,agarose,rhamnan,and ulvan.When hydrolyzed,MAP generate marine algae oligosaccharides(MAO),which have attracted interest in recent years due to their superior solubility compared with MAP.Besides,MAO have been demonstrated numerous biological activities including antioxidant,antidiabetic,anti-inflammatory,antimicrobial,and prebiotic activities.Thus,this review summarizes the main chemical classes of MAO,their sources,and the main processes used for their production(i.e.,physical,chemical,and biological methods),coupled with a discussion of the advantages and disadvantages of these methods.Highlights of the biological activities of MAO and their potential applications in food,nutraceutical,and pharmaceuticals would also be discussed and summarized.

From concept to commercialization:A review of tubular solid oxide fuel cell technology

The reduced sealing difficulty of tubular solid oxide fuel cells(SOFCs)makes the stacking of tubular cell groups relatively easy,and the thermal stress constraints during stack operation are smaller,which helps the stack to operate stably for a long time.The special design of tubular SOFC structures can completely solve the problem of high-temperature sealing,especially in the design of multiple single-cell series integrated into one tube,where each cell tube is equivalent to a small electric stack,with unique characteristics of high voltage and low current output,which can significantly reduce the ohmic polarization loss of tubular cells.This paper provides an overview of typical tubular SOFC structural designs both domestically and internationally.Based on the geometric structure of tubular SOFCs,they can be divided into bamboo tubes,bamboo flat tubes,single-section tubes,and single-section flat tube structures.Meanwhile,this article provides an overview of commonly used materials and preparation methods for tubular SOFCs,including commonly used materials and preparation methods for support and functional layers,as well as a comparison of commonly used preparation methods for microtubule SOFCs,It introduced the three most important parts of building a fuel cell stack:manifold,current collector,and ceramic adhesive,and also provided a detailed introduction to the power generation systems of different tubular SOFCs,Finally,the development prospects of tubular SOFCs were discussed.

Effect of preparation methods on the adsorption property of municipal solid waste-based carbon materials

Three different preparation methods including steam physical activation, catalytic carbonation and KOH chemical activation methods were used to prepare municipal solid waste- based carbon materials. The methylene blue （MB） adsorption value was applied to evaluate the adsorption capabilities of the prepared carbon materials. The effects of preparation methods on adsorption capability and yield of products were investigated. The yield of carbon materials with the catalytic carbonation method is the highest, and the KOH activation method is the second level. Considering the adsorption performance, the KOH activation method is much more favorable. Among the different components of municipal solid waste-based carbon materials, the adsorption properties of the single component of paperboard, the double components of tire and paperboard, the triple components of tire, paperboard and polyvinyl chloride （PVC）, and the multi-component mixtures are better than those of other single-, double-, triple- and multi-component mixtures, respectively.

The preparation and properties of N-doped carbon materials and their use for sodium storage

Defect engineering by heteroatom doping gives carbon materials some new characteristics such as a different electronic structure and a high electrochemical activity,making them suitable for high-performance applications.N-doping has been widely investigated because of its similar atom radius to carbon,high electronegativity as well as many different configurations.We summarize the preparation methods and properties of N-doped carbon materials,and discuss their possible use in sodium ion storage.The relationships between N content/configuration and crystallinity,electronic conductivity,wettability,chemical reactivity as well as sodium ion storage performance are discussed.

Novel wood-plastic composite fabricated via modified steel slag:Preparation,mechanical and flammability properties

A novel method was developed to enhance the utilization rate of steel slag(SS).Through treatment of SS with phosphoric acid and aminopropyl triethoxysilane(KH550),we obtained modified SS(MSS),which was used to prepare MSS/wood-plastic composites(MSS/WPCs)by replacing talcum powder(TP).The composites were fabricated through melting blending and hot pressing.Their mechanical and combustion properties,which comprise heat release,smoke release,and thermal stability,were systematically investigated.MSS can improve the mechanical strength of the composites through grafting reactions between wood powder and thermoplastics.Notably,MSS/WPC#50(16wt%MSS)with an MSS-to-TP mass ratio of 1:1 exhibited optimal comprehensive performance.Compared with those of WPC#0 without MSS,the tensile,flexural,and impact strengths of MSS/WPC#50 were increased by 18.5%,12.8%,and 18.0%,respectively.Moreover,the MSS/WPC#50 sample achieved the highest limited oxygen index of 22.5%,the highest vertical burning rating at the V-1 level,and the lowest horizontal burning rate at 44.2 mm/min.The formation of a dense and stable char layer led to improved thermal stability and a considerable reduction in heat and smoke releases of MSS/WPC#50.However,the partial replacement of TP with MSS slightly compromised the mechanical and flame-retardant properties,possibly due to the weak grafting caused by SS powder agglomeration.These findings suggest the suitability of MSS/WPCs for high-value-added applications as decorative panels indoors or outdoors.

Design,preparation,application of advanced array structured materials and their action mechanism analyses for high performance lithium-sulfur batteries

Lithium-sulfur battery(LSB)has brought much attention and concern because of high theoretical specific capacity and energy density as one of main competitors for next-generation energy storage systems.The widely commercial application and development of LSB is mainly hindered by serious“shuttle effect”of lithium polysulfides(Li PSs),slow reaction kinetics,notorious lithium dendrites,etc.In various structures of LSB materials,array structured materials,possessing the composition of ordered micro units with the same or similar characteristics of each unit,present excellent application potential for various secondary cells due to some merits such as immobilization of active substances,high specific surface area,appropriate pore sizes,easy modification of functional material surface,accommodated huge volume change,enough facilitated transportation for electrons/lithium ions,and special functional groups strongly adsorbing Li PSs.Thus many novel array structured materials are applied to battery for tackling thorny problems mentioned above.In this review,recent progresses and developments on array structured materials applied in LSBs including preparation ways,collaborative structural designs based on array structures,and action mechanism analyses in improving electrochemical performance and safety are summarized.Meanwhile,we also have detailed discussion for array structured materials in LSBs and constructed the structure-function relationships between array structured materials and battery performances.Lastly,some directions and prospects about preparation ways,functional modifications,and practical applications of array structured materials in LSBs are generalized.We hope the review can attract more researchers'attention and bring more studying on array structured materials for other secondary batteries including LSB.

Research Progress of High Entropy Ceramic Materials

High-entropy materials(HEMs)have better mechanical,thermal,and electrical properties than traditional materials due to their special"high entropy effect".They can also adjust the performance of high entropy ceramics by adjusting the proportion of raw materials,and have broad application prospects in many fields.This article provides a review of the high entropy effect,preparation methods,and main applications of high entropy ceramic materials,especially exploring relevant research on high entropy perovskite ceramics.It is expected to provide reference for the promotion of scientific research and the development of further large-scale applications of high-entropy ceramic materials.

Influence of preparation methods on the physicochemical properties and catalytic performance of MnO_x-CeO_2 catalysts for NH_3-SCR at low temperature

This work examines the influence of preparation methods on the physicochemical properties and catalytic performance of MnOx‐CeO2 catalysts for selective catalytic reduction of NO by NH3 (NH3‐SCR) at low temperature. Five different methods, namely, mechanical mixing, impregnation,hydrothermal treatment, co‐precipitation, and a sol‐gel technique, were used to synthesizeMnOx‐CeO2 catalysts. The catalysts were characterized in detail, and an NH3‐SCR model reaction waschosen to evaluate the catalytic performance. The results showed that the preparation methodsaffected the catalytic performance in the order: hydrothermal treatment > sol‐gel > co‐precipitation> impregnation > mechanical mixing. This order correlated with the surface Ce3+ and Mn4+ content,oxygen vacancies and surface adsorbed oxygen species concentration, and the amount of acidic sitesand acidic strength. This trend is related to redox interactions between MnOx and CeO2. The catalystformed by a hydrothermal treatment exhibited excellent physicochemical properties, optimal catalyticperformance, and good H2O resistance in NH3‐SCR reaction. This was attributed to incorporationof Mnn+ into the CeO2 lattice to form a uniform ceria‐based solid solution (containing Mn‐O‐Cestructures). Strengthening of the electronic interactions between MnOx and CeO2, driven by thehigh‐temperature and high‐pressure conditions during the hydrothermal treatment also improved the catalyst characteristics. Thus, the hydrothermal treatment method is an efficient and environment‐friendly route to synthesizing low‐temperature denitrification (deNOx) catalysts.

Influence of preparation methods on CuO-CeO_2 catalysts in the preferential oxidation of CO in excess hydrogen

Influence of three different preparation methods, i.e. impregnation, coprecipitation, and inverse coprecipitation, on the preferential oxidation of CO in excess hydrogen （PROX） over CuO-CeO2 catalysts has been investigated and CuO-CeO2 catalysts are characterized using BET, XPS, XRD, UV Raman, and TPR techniques. The results show that the catalysts prepared by coprecipitation have smaller particle sizes, well-dispersed CuOx species, more oxygen vacancies, and are more active in the PROX than those prepared by the other methods. However. the inverse coprecipitation depresses the catalytic performance of CuO-CeO2 catalysts and causes the growth of CuO-CeO2 because of different pH value in the precipitation process.

Effect of Preparation Methods of Bi_(2)O_(3) Nanoparticles on their Photocatalytic Activity

Bi 2O 3 nanoparticles were prepared by means of ammonia precipitation, polyol mediated methods and microemulsion chemical method. The structure and properties of the as-prepared nanoparticles, having been submitted to a heat-treatment test at 750 ℃, were characterized by means of XRD, BET, XPS and UV-Vis absorption techniques. The photocatalytic oxidation reactions of benzene, toluene and xylene were used as the model reaction to measure the photocatalytic activity of Bi 2O 3 nanoparticles, respectively. The results show that the crystallite size of Bi 2O 3 prepared with different methods and calcined at 750 ℃ were 50.6, 38.5 and 31.5 nm, respectively. The photocatalytic activity of Bi 2O 3 nanoparticles prepared with the microemulsion chemical method was higher than that of the particles prepared with the polyol mediated method; and that of the particles prepared with the micromulsion chemical method was the highest among the three. The degradation rates of the three pollutants xylene, toluene and benzene decreased in sequence.

Effect of preparation methods on the hydrocracking performance of NiMo/Al_(2)O_(3) catalysts

In this work,NiMo catalysts with various contents of MoO_(3)were prepared through incipient wetness impregnation by a twostep method(NMxA)and onepot method(NMxB).The catalysts were then characterized by XRD,XPS,NH3TPD,H_(2)TPR,HRTEM,and N_(2)adsorptiondesorption technologies.The performance of the NiMo/Al_(2)O_(3) catalysts was investigated by hydrocracking lowtemperature coal tar.When the MoO3 content was 15 wt%,the interaction between Ni species and Al_(2)O_(3) on the NM15B catalyst was stronger than that on the NM15A catalyst,resulting in the poor performance of the former.When the MoO^(3) content was 20 wt%,MoO_(3) agglomerated on the surface of the NM20A catalyst,leading to decreased number of active sites and specific surface area and reduced catalytic performance.The increase in the number of MoS_(2) stack layers strengthened the interaction between Ni and Mo species of the NM20B catalyst and consequently improved its catalytic performance.When the MoO_(3) content reached 25 wt%,the active metals agglomerated on the surface of the NiMo catalysts,thereby directly decreasing the number of active sites.In conclusion,the twostep method is suitable for preparing catalysts with large pore diameter and low MoO_(3) content loading,and the onepot method is more appropriate for preparing catalysts with large specific surface area and high MoO_(3) content.Moreover,the NMxA catalysts had larger average pore diameter than the NMxB catalysts and exhibited improved desulfurization performance.

Effect of preparation methods on the structure and catalytic performance of Fe–Zn/K catalysts for CO2 hydrogenation to light olefins

Potassium promoted iron–zinc catalysts prepared by co-precipitation method(C–Fe–Zn/K),solvothermal method(S–Fe–Zn/K)and hydrothermal method(H–Fe–Zn/K)could selectively convert CO_2to light olefins,respectively.The physicochemical properties of the obtained catalysts were determined by SEM,N_2physisorption,XRD,H_2-TPR,CO_2-TPD and XPS measurements.The results demonstrated that preparation methods had great influences on the morphology,phase structures,reduction and adsorption behavior,and hence the catalytic performance of the catalysts.The samples prepared by hydrothermal and co-precipitation method generated small uniform particles and led to lower specific surface area.In contrast,microspheres with larger specific surface area were formed by self-assembly of nanosheets using solvothermal method.ZnFe_2O_4was the only detectable phase in the fresh C–2Fe–1Zn/K,S–3Fe–1Zn/K and S–2Fe–1Zn/K samples.ZnFe_2O_4and ZnO co-existed with increasing Zncontent in S–1Fe–1Zn/K sample,while ZnO and Fe_2O_3could be observed over H–2Fe–1Zn/K sample.All the used samples contained Fe_3O_4,ZnO and Fe_5C_2.The peak intensity of ZnO was strong in the AR-H–2Fe–1Zn/K sample while it was the lowest in the AR-C–2Fe–1Zn/K sample after reaction.The formation of ZnFe_2O_4increased the interaction between iron and zinc for C–2Fe–1Zn/K and S–Fe–Zn/K samples,causing easier reduction of Fe_2O_3to Fe_3O_4.The surface basicity of the sample prepared by co-precipitation method was much more than that of the other two methods.During CO_2hydrogenation,all the catalysts showed good activity and olefin selectivity.The CO selectivity was increased with increasing Zncontent over S–Fe–Zn/K samples.H–2Fe–1Zn/K catalyst preferred to the production of C_5^+hydrocarbons.CO_2conversion of 54.76%and C_2~=–C_4~=contents of 57.38%were obtained on C–2Fe–1Zn/K sample,respectively.

Effect of preparation methods on Pt/alumina catalysts for the hydrogen iodide catalytic decomposition

Three kinds of Pt/alumina catalysts were prepared by impregnation-hydrogen reduction, impregnation-hydrazine reduction and electroless plating methods. Their differences in the structures, specific areas and particle sizes were characterized by XRD, BET and TEM, respectively. Furthermore, their catalytic activities for the hydrogen iodide （HI） decomposition were evaluated in a fixed bed reactor. The results show that the catalyst 5%Pt/Al2O3 prepared by the electroless plating has the optimum catalytic properties for HI decomposition owing to the high dispersion of the platinum nano-particles （〈5 nm） on the alumina supports.

Analysis and discussion of different methods of artificial ice-high specimen preparation

Because ice-high foundation soil is widely distributed in permafrost regions,the correct preparation of ice-high specimens is of critical interest in engineering design for foundation stability.Past research has shown that the uniaxial compression strength of ice-high frozen soils changes as the ice or total water content increases; the differences of different methods of specimen preparation are analyzed here and the advantages and disadvantages of them are presented.It is confirmed that the role of crushed ice is significantly different from that of naturally frozen ice in frozen soils,and the size and amount of crushed ice will influence the strength and deformation mechanism of frozen soils.Therefore,it is strongly recommended that when a ice-high specimen is artificially prepared,the ice should be frozen through natural means and not be replaced with crushed ice.

Classification of Preparation Methods and Wearability of Smart Textiles

In recent years,smart textiles have attracted the attention of scholars from all walks of life,but there is an imbalance between functionality and usability,which affects their marketization process.Firstly,five representative smart textiles are introduced and their respective wearability is described around preparation methods.Secondly,it is concluded that the preparation methods of smart textiles can be divided into two categories:fiber methods and finishing methods.The fiber methods refer to making smart fibers into smart textiles.Textiles made by fiber methods are breathable and feel good in the hand,but the mechanical properties are influenced by the production equipment,and the process cost is high.The finishing methods refer to the functional finishing of ordinary textiles.Although the finishing method is simple and convenient,it may reduce the comfort of the textile.Finally,applications and new research in various fields of smart textiles are presented with promising prospects.It is anticipated that this review will serve as a theoretical basis for future research and development of smart textiles.Researchers are expected to create new technologies to overcome the tension between functionality and usability,as well as to increase user comfort and convenience.