Pressure leaching technique of smelter dust with high-copper and high-arsenic

The application of pressure leaching technology in the treatment of high-copper and high-arsenic dust was studied.The pressure leaching technique was determined as follows:the liquid to solid ratio(mL/g)of 5:1,the leaching temperature of 453 K,the retention time of 2 h,the initial sulfuric acid concentration of 0.74 mol/L,the oxygen partial pressure of 0.7 MPa,and the agitation speed of 500 r/min.Under these conditions,95%of copper and 99%of zinc and only 6%of iron in the dust were leached,while about 20%of arsenic was also leached.The leaching technique was optimized further to restrain the leaching of arsenic by adding a small quantity of ferrous iron into the leaching system(c(Fe2 +)=0.036 mol/L).Copper and zinc can be effectively separated from arsenic and iron in the leach.The optimal pressure leaching technique of high-copper and high-arsenic smelter dust is proved to be effective.

Kinetics of iron removal from metallurgical grade silicon with pressure leaching

In this paper, the kinetics of pressure leaching for purification of metallurgical grade silicon with hydrochloric acid was investigated. The effects of particle size, temperature, total pressure, and concentration of hydrochloric acid on the kinetics and mechanism of iron removal were studied. It was found that the reaction kinetic model followed the shrinking core model, and the apparent activation energy of the leaching reaction was 46.908 kJ/mol. And the apparent reaction order of iron removal with pressure leaching was 0.899. The kinetic equation was obtained and the mathematical model of iron removal from metallurgical grade silicon （MG-Si） was given as follows：The values calculated from the equation were consistent with the experimental results.

Pressure leaching of zinc silicate ore in sulfuric acid medium

Zinc silicate ore was characterized mineralogically and the results showed that zinc exists mainly as hemimorphite and smithsonite in the sample.Sulfuric acid pressure leaching of zinc silicate ore was carried out to assess the effect of particle size,sulfuric acid concentration,pressure,reaction time and temperature on the extraction of zinc and the dissolution of silica.Under the optimum conditions employed,up to 99.25% of zinc extraction and 0.20% silica dissolution are obtained.The main minerals in leaching residue are quartz and small amounts of undissolved oxide minerals of iron,lead and aluminum are associated with quartz.

Microwave pretreatment for enhanced selective nitric acid pressure leaching of limonitic laterite

As clean energy,the microwave is commonly used to pretreat various ores.In this work,the microwave dielectric properties of limonitic laterite ore were measured by resonant cavity perturbation technique and the effects from microwave were systematically investigated.Results indicated that limonitic laterite had high microwave absorbance.After microwave pretreatment,the microstructure of the laterite became less aggregated and more porous and the main phase transformed from goethite to hematite that improved leaching in nitric acid(1.2 kg HNO3/kg ore);Ni,Co,Fe,and Mg extraction ratios were 95.2%,98.1%,1.8%and 15%,respectively,after leaching for 60 min at 200°C and 500 r/min.Furthermore,in the process of goethite to hematite by microwave pretreatment,the nickel-containing mineral is activated,which makes nickel be leached easily.The leaching process has high Ni extraction ratio compared to that without microwave(82%)and conventional pretreatment(90.4%).Therefore,microwave pretreatment of limonitic laterite before nitric acid pressure leaching is an effective way to improve the selectivity and extraction of the leach.

Intensification of pretreatment and pressure leaching of copper anode slime by microwave radiation

The application of microwave irradiation for pretreatment of copper anode slime with high nickel content prior to pressure sulfuric acid leaching has been proposed.The microwave-assisted pretreatment is a rapid and efficient process.Through the technology of microwave assisted pretreatment-pressure leaching of copper anode slime,copper,tellurium,selenium and nickel are almost completely recovered.Under optimal conditions,the leaching efficiencies of copper,tellurium,selenium and nickel are 97.12%,95.97%,95.37% and 93.90%,respectively.The effect of microwave radiation on the temperature of copper anode slime and leaching solution is investigated.It is suggested that the enhancement on the recoveries of copper,tellurium and selenium can be attributed to the temperature gradient which is caused by shallow microwave penetration depth and super heating occurring at the solid–liquid interface.The kinetic study shows that the pressure leaching of copper anode slime,with and without microwave assisted pretreatment,are both controlled by chemical reactions on the surfaces of particles.It is found that the activation energy calculated for microwave-assisted pretreatment-pressure leaching(49.47 kJ/mol) is lower than that for pressure leaching which is without microwave assisted pretreatment(60.57 kJ/mol).

Indium recovery from zinc oxide flue dust by oxidative pressure leaching

Indium was recovered from zinc oxide flue dust(ZOFD)with sulfuric acid by oxidative pressure leaching in an autoclave, and the effects of different technological conditions on indium leaching were studied.Potassium permanganate and hydrogen peroxide were used as oxidants.The atmospheric pressure leaching experiments were also carried out.The experimental results show that the leaching rate of indium can be effectively improved by oxidative pressure leaching.The optimum conditions of pressure leaching are determined as sulfuric 5.10 mol/L acid,leaching time 150 min,temperature 90℃,and the H2O2 dosage of 0.5 mL/g or 2.5%KMnO4.The leaching rate of indium is more than 90%,which is increased by 13%compared with that of atmospheric pressure leaching process without oxidant under the optimum conditions.

E-pH diagram of ZnS-H_2O system during high pressure leaching of zinc sulfide

The values of GΘ,EΘ or pH from 110 to 160℃ were calculated and the relevant potential expressions were obtained.E-pH diagrams of ZnS-H2O system at oxygen partial pressure of 0.8 MPa,ionic activity of 1.0 and different temperatures were drawn through thermodynamical calculation.With the temperature increasing,the stable regions of S and Zn(Ⅱ) in the E-pH diagrams become gradually larger,but the amplification decreases over 150℃.The impacts of leaching parameters,such as temperature,liquid to solid ratio,initial acidic concentration,leaching time,oxygen partial pressure and stirring speed on the leaching rate of Zn(Ⅱ) and conversion rate of S in the single factor of high pressure leaching experiment of ZnS in autoclave,were studied.The leaching residue was examined by X-ray fluorescence(XRF) chemical composition identification and X-ray diffraction(XRD) phase identification,and the content of the leaching solution was tested by inductively coupled plasma-atomic emission spectrometry(ICP).The experimental results indicate that the leaching rate of zinc increases from 60.05% to 97.85% and the conversion rate of sulfur increases from 38.90% to 80.92% with the temperature increasing from 110℃ to 150℃,5:1 of liquid-to-solid ratio,150 g/L of initial acidic concentration,120 min of leaching time,0.8 MPa of oxygen partial pressure,and 480 r/min of stirring speed,which tend to be stable over 150℃.The experimental results correspond with theoretical calculation.

Pressure leaching of bismuth sulfide concentrate containing molybdenum and tungsten in alkaline solution

The leaching results of bismuth sulfide concentrate containing molybdenum and tungsten in air-H2O2-NaOH system, pressure-O2-Na2CO3 system and pressure-O2-NaOH system were investigated. The results show that the extraction of molybdenum, tungsten and sulfur goes up with the increase of NaOH concentration, oxygen partial pressure and reaction time. The extraction of molybdenum and tungsten also rises up with temperature, but the leaching ratio of sulfur increases initially to a peak of 98% at 150℃ and then decreases with the increase of temperature. Under the optimal conditions, the extraction of molybdenum, tungsten and sulfur is more than 95.6%, 93.8% and 96.0%, respectively, and the main phases of residue are Bi2O3 and Fe2O3. Therefore, the method of pressure leaching in alkaline solution is provided as an effective separation of molybdenum, tungsten and sulfur from bismuth and a beneficial pretreatment for consequent process.

Oxygen pressure leaching-flotation joint process for Jinbaoshan platinum group minerals

An oxygen pressure leaching-flotation joint process was proposed to treat Jinbaoshan platinum group minerals to produce a desired concentrate. The result demonstrates that leaching parameters which include particle size, stirring speed, liquid-solid ratio, and the dosage of calcium lignosulfonate, simultaneously affect the leaching rates of base metals and the recovery of platinum group metals (PGMs). The complete dissolution of base metals sulfides leads to a reduction in the amount of flotation carrier for enriching PGMs, decreasing the recovery of PGMs. The optimum leaching conditions are determined as follows: liquid-solid ratio of 10 mL/g, 73% occupancy of ore particle size below 0.043 mm, stirring speed of 400 r/min, and 0.6 g dosage of calcium lignosulfonate. Under optimal conditions, the leaching rates of Cu, Ni and Fe are 87.6%, 87.6% and 90.3%, respectively. The grade of PGMs enriched in the flotation concentrate is 420 g/t through the flotation technology.

Recovery of zinc from electric arc furnace dust by alkaline pressure leaching using iron as a reductant

To recover zinc from electric arc furnace(EAF)dust,a process of primary normal pressure leaching and secondary alkaline pressure leaching is proposed.First,under the alkaline pressure leaching system,the experiment of pure zinc ferrite being reduced by iron powder was carried out.Under the optimal reduction conditions(i.e.,temperature of 260℃,NaOH concentration of 6 mol/L,liquid-to-solid ratio of 50 mL/g,and a 5-fold excess of iron powder),89%of zinc was extracted.The iron in the reduced residue exists as a magnetite phase.Subsequently,the normal pressure leaching experiment was carried out with EAF dust as raw material,and 66%zinc was leached.The main phase of zinc in normal leaching residue was determined to be zinc ferrite.Then,the normal leaching residue was reduced by iron powder under the alkaline pressure leaching system,and 66.5%of zinc was extracted.After the two-stage leaching process,the leaching rate of zinc in EAF dust can achieve 88.7%.The alkaline pressure leaching solution can be returned as the normal pressure leaching solution,and the magnetite in the alkaline pressure leaching residue can be recovered by magnetic separation.

Extraction of molybdenum and nickel from Ni-Mo ore by pressure acid leaching

A direct hydrometallurgical route for nickel and molybdenum extraction from a nickel-molybdenum （Ni-Mo） ore using pressure acid leaching was studied. The nickel and molybdenum were extracted by acid leaching under oxygen pressure. Compared with traditional roasting methods, this hydrometallurgical method eliminates SO2 and As203 emission （the Ni-Mo ore containing 15%-25% S）. Compared with existing alkali leaching recovery of molybdenum process, almost all the nickel and considerable molybdenum were extracted in the acid leaching process. Under oxygen pressure conditions, almost all the nickel and a substantial part of the molybdenum were dissolved into the acid leaching liquor and the other part of the molybdenum was left in the acid leach residue. The acid leach residue was further leached under alkaline （NaOH） conditions. Under optimal experimental conditions, the extraction rates nickel and molybdenum reached 97% and 96%, respectively.

Leaching behavior of metals from limonitic laterite ore by high pressure acid leaching

The leaching behavior of metals from a nickeliferous limonitic laterite ore was investigated by high pressure acid leaching process for the extraction of nickel and cobalt.The effects of sulfuric acid added,leaching temperature,leaching time and liquid/solid（L/S） ratio on metals extraction were examined.More than 97% Ni,96% Co,93% Mn,95% Mg and less than 1% Fe are extracted under optimum conditions.Analysis of the high pressure acid leaching residue by chemical and XRD analysis indicates that the residual iron and sulfur are mainly present in phases of hematite and alunite,respectively.The high pressure leaching process provides a simple and efficient way for the high recovery of nickel and cobalt from laterite ore,leaving residue as a suitable iron resource.

φ-pH diagram of V-Ti-H_2O system during pressure acid leaching of converter slag containing vanadium and titanium

To analyze the thermodynamic characteristics of leaching process of converter slag, φ-pH diagram of V-Ti-H2O system at oxygen partial pressure of 0.5 MPa, ionic mass concentration of 0.1 mol/kg and temperatures ranging from 60 to 200 ℃ was obtained by recently published critically assessed standard Gibbs energies and activity coefficients of various species. When pH2, stable regions of V3＋, VO2＋ and VO2＋ exist in the stable region of TiO2. The pH values of stable regions of vanadium and titanium decrease and redox potentials become more positive with the temperature increasing. Vanadium and titanium could be separated by one-step leaching based on thermodynamics. The experiment results of pressure acid leaching of converter slag show that leaching rates of vanadium and titanium are 96.87% and 8.76% respectively, at 140 ℃ of temperature, 0.5 MPa of oxygen partial pressure, 0.055-0.075mm of particle size, 15：1 of liquid to solid ratio, 120 min of leaching time, 500 r/min of stirring speed and 200 g/L of initial acid concentration. Vanadium and titanium could be selectively separated in the pressure acid leaching process, and the experiment result is in agreement with thermodynamic calculation result.

Extraction of vanadium from vanadium slag by high pressure oxidative acid leaching

To extract vanadium in an environment friendly manner, this study focuses on the process of leaching vanadium from vanadium slag by high pressure oxidative acid leaching. Characterizations of the raw slag, mineralogy transformation, and the form of leach residues were made by X-ray diffraction, scanning electron microscopy, and energy dispersive X-ray spectroscopy. The result shows that the vana-dium slag is composed of major phases of fayalite, titanomagnetite, and spinel. During the high pressure oxidative acid leaching process, the fayalite and spinel phases are gradually decomposed by sulfuric acid, causing the release of vanadium and iron in the solution. Meanwhile, unreacted silicon and titanium are enriched in the leach residues. With the initial concentration of sulfuric acid at 250 g·L^-1, a leaching tem-perature of 140℃, a leaching time of 50 min, a liquid-solid ratio of 10：1 mL·g^-1, and oxygen pressure at 0.2 MPa, the leaching rate of vana-dium reaches 97.69%.

Selective recovery of lithium from spent lithium iron phosphate batteries using oxidation pressure sulfuric acid leaching system

Oxidation pressure leaching was proposed to selectively dissolve Li from spent LiFePO_(4) batteries in a stoichiometric sulfuric acid solution.Using O_(2) as an oxidant and stoichiometric sulfuric acid as leaching agent,above 97% of Li was leached into the solution,whereas more than 99% of Fe remained in the leaching residue,enabling a relatively low cost for one-step separation of Li and Fe.And then,by adjusting the pH of leachate,above 95% of Li was recovered in the form of the Li_(3)PO_(4) product through iron removal and chemical precipitation of phosphate.

Pressure leaching of converter vanadium slag with waste titanium dioxide

The process of pressure leaching the converter vanadium slag with waste titanium dioxide without roasting was studied. Mineralogy analysis indicates that the con- verter vanadium slag contains mainly three mineral phases： magnetite, titanium magnetite, and silicate phase. Vana- dium is in combination with iron, titanium, manganese, aluminum, and silicon. The impacts of leaching tempera- ture, leaching time, stirring speed, liquid-to-solid ratio, and initial leaching agent concentration were investigated on the waste titanium dioxide leaching process. The results indi- cate that under the optimal conditions, the vanadium and the iron leaching rates are 96.85 % and 93.50 %, respectively, and the content of titanium is 12.6 % in the residue. The main mineral phases for the residues under the optimal operation conditions are quartz, ilmenite, anatase, and sili- cate phase, and the residues can be reused as the extraction of titanium raw materials for titanium dioxide production technology by the sulfate method.

An investigation of oxygen pressure acid leaching of Gacun complex Cu-Pb bulk concentrate

The treatment of the Gacun complex Cu-Pb bulk concentrate with high Zn,Ag,etc.,by oxygen pressure acid leaching was studied.The pri-mary copper and leadminerals in the concentrate are tetrahedrite and galena.The treatment of tetrahedrite was rarely studied,and most of silver occurred in themineral too.The optimum operating parameters of oxygen pressure acid leaching were established by conditional tests.Under these parameters,the result of pilot scale test showed that the leaching percentages of copper and zinc were separately as high as 98.9 wt.% and 94.9 wt.%,while lead and silver were transformed into sulfate and sulfide precipitations,respectively.The copper and zinc in lixivium were reclaimed by extraction-electrowinning and purification-electrowinning,respectively,and the lead and silver in the residue were reclaimed separately by carbonate transformation-silicofluoric acid leaching and thiourea leaching.

Pressure acid leaching of zinc sulfide concentrate

Effects of particle size of the zinc sulfide concentrate,leaching temperature,solid-to-liquid ratio and additive amount on pressure acid leaching process of the zinc sulfide concentrate were studied.The results indicate that the additive can improve the reaction kinetics and the conversion rate.And sulfur can be successfully separated from the zinc sulfide concentrate as elemental sulfur.The reasonable experiment parameters are obtained as follows:the leaching temperature 150℃,oxygen partial pressure 1 MPa,additive amount 1%,solid-to-liquid ratio 1:4,leaching time 2 h,initial sulfuric acid concentration 15%,and particle size less than 44μm.Under the optimum conditions,the leaching rate of the zinc can reach 95%and the reduction rate of the sulfur can reach 90%.

Recovery of gallium from zinc concentrate by pressure oxygen leaching

Zinc concentrate with high gallium content is one of the main resources of gallium.The gallium presents in the form of isomorphism in tetrahedron coordination with sulfur in sphalerite.The research was to investigate the amenability of zinc concentrate with high gallium to pressure oxygen leaching.The particle size,sulfuric acid concentration,oxygen partial pressure,additive amount,and time of reaction were studied.The extraction yields of gallium and zinc are 86%and 98%,respectively.The optimal condition is 100 g of zinc concentrate with particle size smaller than 38 lm,sulfuric acid concentration150 g L-1,leaching temperature 150℃,leaching time120 min,oxygen partial pressure 0.7 MPa,additive amount of 0.2 wt%.

Pressure acid leaching of black shale for extraction of vanadium

Extraction of vanadium from black shale was attempted in pressure acid leaching.The chemical components of the sample obtained from Guizhou Province of China show that it contains 3.258%V2O5,52.880%SiO2 and 16.140%Al2O3.Phase analyses of vanadium indicates vanadium mainly exists in the free oxide and mica.Vanadium contents in the two phases are 18%and 53%, respectively.The contents of V3 +,V 4+and V 5+are almost equal.Under the optimum parameters of one-step leaching(reaction time of 3 h,sulfuric addition of 25%,temperature of 150℃,liquid to solid ratio of 1.2 mL/g,catalyst(FeSO4)addition of 5%and size of 85%particle 0.074 mm),about 77%of vanadium is recovered.After two-step countercurrent leaching,the leach recovery of vanadium can reach above 90%.Air replacing oxygen is completely feasible.The impurity metals can dissolve into solution in different degrees.