A computational study was carried out on bubble dynamic behaviors and bubble size distributions in a pressurized lab-scale gas-solid fluidized bed of Geldart A particles.High-resolution 3-D numerical simulations were ...A computational study was carried out on bubble dynamic behaviors and bubble size distributions in a pressurized lab-scale gas-solid fluidized bed of Geldart A particles.High-resolution 3-D numerical simulations were performed using the two-fluid model based on the kinetic theory of granular flow.A finegrid,which is in the range of 3–4 particle diameters,was utilized in order to capture bubble structures explicitly without breaking down the continuum assumption for the solid phase.A novel bubble tracking scheme was developed in combination with a 3-D detection and tracking algorithm(MS3 DATA)and applied to detect the bubble statistics,such as bubble size,location in each time frame and relative position between two adjacent time frames,from numerical simulations.The spatial coordinates and corresponding void fraction data were sampled at 100 Hz for data analyzing.The bubble coalescence/break-up frequencies and the daughter bubble size distribution were evaluated by using the new bubble tracking algorithm.The results showed that the bubble size distributed non-uniformly over cross-sections in the bed.The equilibrium bubble diameter due to bubble break-up and coalescence dynamics can be obtained,and the bubble rise velocity follows Davidson’s correlation closely.Good agreements were obtained between the computed results and that predicted by using the bubble break-up model proposed in our previous work.The computational bubble tracking method showed the potential of analyzing bubble motions and the coalescence and break-up characteristics based on time series data sets of void fraction maps obtained numerically and experimentally.展开更多
The particle residence time distribution(RTD)and axial dispersion coefficient are key parameters for the design and operation of a pressurized circulating fluidized bed(PCFB).In this study,the effects of pressure(0.1-...The particle residence time distribution(RTD)and axial dispersion coefficient are key parameters for the design and operation of a pressurized circulating fluidized bed(PCFB).In this study,the effects of pressure(0.1-0.6 MPa),fluidizing gas velocity(2-7 m·s^(-1)),and solid circulation rate(10-90 kg·m^(-2)·s^(-1))on particle RTD and axial dispersion coefficient in a PCFB are numerically investigated based on the multiphase particle-in-cell(MP-PIC)method.The details of the gas-solid flow behaviors of PCFB are revealed.Based on the gas-solid flow pattern,the particles tend to move more orderly under elevated pressures.With an increase in either fluidizing gas velocity or solid circulation rate,the mean residence time of particles decreases while the axial dispersion coefficient increases.With an increase in pressure,the core-annulus flow is strengthened,which leads to a wider shape of the particle RTD curve and a larger mean particle residence time.The back-mixing of particles increases with increasing pressure,resulting in an increase in the axial dispersion coefficient.展开更多
Pressure fluctuations signals of a lab-scale fiuidized bed (15 cm inner diameter and 2 m height) at different superficial gas velocities were measured. Recurrence plot (RP) and recurrence rate (RR), and the simp...Pressure fluctuations signals of a lab-scale fiuidized bed (15 cm inner diameter and 2 m height) at different superficial gas velocities were measured. Recurrence plot (RP) and recurrence rate (RR), and the simplest variable of recurrence quantification analysis (RQA) were used to analyze the pressure signals. Different patterns observed in RP reflect different dynamic behavior of the system under study. It was also found that the variance of RR (a2R) Could reveal the peak dominant frequencies (PDF) of different dynamic systems: completely periodic, completely stochastic, Lorenz system, and fluidized bed. The results were compared with power spectral density. Additionally, the diagram of σ^2RR provides a new technique for prediction of transition velocity from bubbling to turbulent fluidization regime.展开更多
The effects of operating pressure on the gas-solid flow characteristics in a pressurized circulating fluidized bed(CFB)gasification system were studied by experiment and simulation.Elevated operating pressure was foun...The effects of operating pressure on the gas-solid flow characteristics in a pressurized circulating fluidized bed(CFB)gasification system were studied by experiment and simulation.Elevated operating pressure was found to increase the particle uniformity in the axial and radial directions.Experiments and simulations both showed that as the operating pressure increased,the pressure drops along the riser height decreased.The experimental pressure drops at the same locations decreased when the operating pressure increased,but the opposite trend was observed in the simulation results.A proper drag model must be developed for the accurate simulation of pressurized CFB operation,and the accuracy of electrical capacitance tomography(ECT)measurement and cross-correlation analysis should be improved for better prediction of the particle circulation flux.展开更多
The dynamic features of an agglomerate bubbling fluidization of nanoparticles were investigated through the analysis of pressure fluctuations. Experiments were carried out in a lab-scale fluidized bed at ambient condi...The dynamic features of an agglomerate bubbling fluidization of nanoparticles were investigated through the analysis of pressure fluctuations. Experiments were carried out in a lab-scale fluidized bed at ambient conditions using 10-15 nm silica nanoparticles without any surface modification. Pressure fluctuation signals were processed in both frequency and time-frequency domains to characterize the behavior of various scales of phenomena (i.e.. macro-, meso-, and micro-structures) during fluidization. Due to the aggregation of nanoparticles, three separate broad peaks were observed in the frequency spectra of the pressure signals measured in the bubbling fluidized bed of nanoparticles. A non-intrusive method based on the decoupling of pressure fluctuations recorded simultaneously in the plenum and in the bed was used to determine the approximate size of the bubbles in the bed.展开更多
The article presents an effort to create dimensionless scaling correlations of the overall bed porosity in the case of magnetically assisted fluidization in a tapered vessel with external transverse magnetic field. Th...The article presents an effort to create dimensionless scaling correlations of the overall bed porosity in the case of magnetically assisted fluidization in a tapered vessel with external transverse magnetic field. This is a stand of portion of new branch in the magnetically assisted fluidization recently created concerning employment of tapered vessels. Dimensional analysis based on "pressure transform" of the initial set of variables and involving the magnetic granular Bond number has been applied to develop scaling relationships of dimensionless groups representing ratios of pressures created by the fluid flow, gravity and the magnetic field over an elementary volume of the fluidized bed. Special attention has been paid on the existing data correlations developed for non-magnetic beds and the links to the new ones especially developed for tapered magnetic counterparts. A special dimensionless variable Xp = (Ar△Dbt)1/3√RgMQ combining Archimedes and Rosensweig numbers has been conceived for porosity correlation. Data correlations have been performed by power-law, exponential decay and asymptotic functions with analysis of their adequacies and accuracies of approximation.展开更多
Gas-solid fluidized beds are widely considered as nonlinear and chaotic dynamic systems. Pressure fluc- tuations were measured in a fluidized bed of 0.15 m in diameter and were analyzed using multiple approaches: dis...Gas-solid fluidized beds are widely considered as nonlinear and chaotic dynamic systems. Pressure fluc- tuations were measured in a fluidized bed of 0.15 m in diameter and were analyzed using multiple approaches: discrete Fourier transform (DFT), discrete wavelet transform (DWT), and nonlinear recur- rence quantification analysis (RQA). Three different methods proposed that the complex dynamics of a fluidized bed system can be presented as macro, meso and micro structures. It was found from DFT and DWT that a minimum in wide band energy with an increase in the velocity corresponds to the transition between macro structures and finer structures of the fluidization system. Corresponding transition veloc- ity occurs at gas velocities of 0.3, 0.5 and 0.6 m]s for sands with mean diameters of 150, 280 and 490/~m, respectively. DFT, DWT, and RQA could determine frequency range of0-3.125 Hz for macro, 3. ! 25-50 Hz for meso, and 50-200 Hz for micro structures. The RQA showed that the micro structures have the least periodicity and consequently their determinism and laminarity are the lowest. The results show that a combination of DFT, DWT, and RQA can be used as an effective approach to characterize multi-scale flow behavior in gas-solid fluidized beds.展开更多
In this paper, the pressure fluctuation in a fluidized bed was measured and processed via standard devia- tion and power spectrum analysis to investigate the dynamic behavior of the transition from the bubbling to tur...In this paper, the pressure fluctuation in a fluidized bed was measured and processed via standard devia- tion and power spectrum analysis to investigate the dynamic behavior of the transition from the bubbling to turbulent regime. Two types (Geldart B and D) of non-spherical particles, screened from real bed materials, and their mixture were used as the bed materials. The experiments were conducted in a semi- industrial testing apparatus. The experimental results indicated that the fluidization characteristics of the non-spherical Geldart D particles differed from that of the spherical particles at gas velocities beyond the transition velocity Uo The standard deviation of the pressure fluctuation measured in the bed increased with the gas velocity, while that measured in the plenum remained constant. Compared to the coarse particles, the fine particles exerted a stronger influence on the dynamic behavior of the fluidized bed and promoted the fluidization regime transition from bubbling toward turbulent. The power spectrum of the pressure fluctuation was calculated using the auto-regressive (AR) model; the hydrodynamics of the flu- idized bed were characterized by the major frequency of the power spectrum of the pressure fluctuation. By combining the standard deviation analysis, a new method was proposed to determine the transition velocity Uk via the analysis of the change in the major frequency. The first major frequency was observed to vary within the range of 1.5 to 3 Hz.展开更多
This paper presents the results of an ongoing investigation into transient pressure pulses using Shan- non entropy. Pressure fluctuations (produced by gas-solid two-phase flow during fluidized dense-phase conveying)...This paper presents the results of an ongoing investigation into transient pressure pulses using Shan- non entropy. Pressure fluctuations (produced by gas-solid two-phase flow during fluidized dense-phase conveying) are recorded by pressure transducers installed at strategic locations along a pipeline. This work validates previous work on identifying the flow mode from pressure signals (Mittal, Mallick, & Wypych, 2014). Two different powders, namely fly ash (median particle diameter 45 μm, particle den- sity 1950 kg/m3. loosely poured bulk density 950 kg/m3) and cement (median particle diameter 15 p,m, particle density 3060 kg/m3, loosely poured bulk density 1070 kg/m3), are conveyed through different pipelines (51 mm I.D. × 70 m length and 63 mm I.D. × 24 m length). The transient nature of pressure fluc- tuations (instead of steady-state behavior) is considered in investigating flow characteristics. Shannon entropy is found to increase along straight pipe sections for both solids and both pipelines. However, Shannon entropy decreases after a bend. A comparison of Shannon entropy among different ranges of superficial air velocity reveals that high Shannon entropy corresponds to very low velocities (i.e. 3-5 m/s) and very high velocities (i.e. 11-14 m/s) while low Shannon entropy corresponds to mid-range velocities (i.e. 6-8 m/s).展开更多
Most hydrodynamic fluidized bed models, including CFD codes, neglect any effects of the plenum chamber volume. Experiments were performed in a 0.13 m ID fluidization column to determine plenum chamber volume effects o...Most hydrodynamic fluidized bed models, including CFD codes, neglect any effects of the plenum chamber volume. Experiments were performed in a 0.13 m ID fluidization column to determine plenum chamber volume effects on fluidized bed hydrodynamics for FCC and glass particles. Two low-pressure-drop distributors were used, one with a single orifice, and the other with 33 orifices and the same total open area as the single orifice. The results show two peaks in the frequency spectra for the single-orifice distributor, one representing bubble eruption at the bed surface and the other of higher frequency corresponding to the bubbling frequency at the distributor. The latter decreased slightly with increasing plenum volume and with increasing bed depth. For the multi-orifice distributor, broad frequency spectra from pressure measurements became narrower and moved towards higher frequency with decreasing plenum volume.展开更多
Fluidized beds frequently involve non-spherical particles, especially if biomass is present. For spheri- cal particles, numerous experimental investigations have been reported in the literature. In contrast, complex-s...Fluidized beds frequently involve non-spherical particles, especially if biomass is present. For spheri- cal particles, numerous experimental investigations have been reported in the literature. In contrast, complex-shaped particles have received much less attention. There is a lack of understanding of how par- ticle shape influences flow-regime transitions. In this study, differently shaped Geldart group D particles are experimentally examined. Bed height, pressure drop, and their respective fluctuations are analyzed. With increasing deviation of particle shape from spheres, differences in flow-regime transitions occur with a tendency for the bed to form channels instead of undergoing smooth fluidization. The correlations available in the literature for spherical particles are limited in their applicability when used to predict regime changes for complex-shaped particles. Hence, based on existing correlations, improvements are derived.展开更多
The hydrodynamics of a gas-liquid-solid fluidized bed was investigated by applying the S statistics method to pressure fluctuations measured under various operating conditions in a laboratory-scale bed. S statistics t...The hydrodynamics of a gas-liquid-solid fluidized bed was investigated by applying the S statistics method to pressure fluctuations measured under various operating conditions in a laboratory-scale bed. S statistics tests reveal the existence of three transition velocities, especially at low gas velocities. Four distinct fluidization regimes, namely, the compacted bed, agitated bed and coalesced and discrete bubble regimes were detected. A comparison of reconstructed attractors of pressure fluctuations measured at different axial positions along the riser and with various solid loadings showed significant differences in the signals compared before fluidization, especially at minimum liquid agitation velocity. Close to the minimum liquid fluidization velocity and high liquid velocities, the variation in particle size has an insignificant effect on the bed hydrodynamics. Therefore, S statistics is a reliable method to demar- cate different fluidization regimes and to characterize the influence of various operating conditions on the hydrodynamics of gas-liquid-solid fluidized beds. The method is applicable in large-scale industrial installations to detect dynamic changes within a bed, such as regime transitions or agglomeration.展开更多
基金supported by the National Natural Science Foundation of China(21908062)。
文摘A computational study was carried out on bubble dynamic behaviors and bubble size distributions in a pressurized lab-scale gas-solid fluidized bed of Geldart A particles.High-resolution 3-D numerical simulations were performed using the two-fluid model based on the kinetic theory of granular flow.A finegrid,which is in the range of 3–4 particle diameters,was utilized in order to capture bubble structures explicitly without breaking down the continuum assumption for the solid phase.A novel bubble tracking scheme was developed in combination with a 3-D detection and tracking algorithm(MS3 DATA)and applied to detect the bubble statistics,such as bubble size,location in each time frame and relative position between two adjacent time frames,from numerical simulations.The spatial coordinates and corresponding void fraction data were sampled at 100 Hz for data analyzing.The bubble coalescence/break-up frequencies and the daughter bubble size distribution were evaluated by using the new bubble tracking algorithm.The results showed that the bubble size distributed non-uniformly over cross-sections in the bed.The equilibrium bubble diameter due to bubble break-up and coalescence dynamics can be obtained,and the bubble rise velocity follows Davidson’s correlation closely.Good agreements were obtained between the computed results and that predicted by using the bubble break-up model proposed in our previous work.The computational bubble tracking method showed the potential of analyzing bubble motions and the coalescence and break-up characteristics based on time series data sets of void fraction maps obtained numerically and experimentally.
基金Financial support of this work by National Natural Science Foundation of China(51976037)。
文摘The particle residence time distribution(RTD)and axial dispersion coefficient are key parameters for the design and operation of a pressurized circulating fluidized bed(PCFB).In this study,the effects of pressure(0.1-0.6 MPa),fluidizing gas velocity(2-7 m·s^(-1)),and solid circulation rate(10-90 kg·m^(-2)·s^(-1))on particle RTD and axial dispersion coefficient in a PCFB are numerically investigated based on the multiphase particle-in-cell(MP-PIC)method.The details of the gas-solid flow behaviors of PCFB are revealed.Based on the gas-solid flow pattern,the particles tend to move more orderly under elevated pressures.With an increase in either fluidizing gas velocity or solid circulation rate,the mean residence time of particles decreases while the axial dispersion coefficient increases.With an increase in pressure,the core-annulus flow is strengthened,which leads to a wider shape of the particle RTD curve and a larger mean particle residence time.The back-mixing of particles increases with increasing pressure,resulting in an increase in the axial dispersion coefficient.
基金Supports from the Iran National Science Foundation(INSF) in lran(No.91001766)
文摘Pressure fluctuations signals of a lab-scale fiuidized bed (15 cm inner diameter and 2 m height) at different superficial gas velocities were measured. Recurrence plot (RP) and recurrence rate (RR), and the simplest variable of recurrence quantification analysis (RQA) were used to analyze the pressure signals. Different patterns observed in RP reflect different dynamic behavior of the system under study. It was also found that the variance of RR (a2R) Could reveal the peak dominant frequencies (PDF) of different dynamic systems: completely periodic, completely stochastic, Lorenz system, and fluidized bed. The results were compared with power spectral density. Additionally, the diagram of σ^2RR provides a new technique for prediction of transition velocity from bubbling to turbulent fluidization regime.
基金the support from the Key Special Project for Transfer and Transformation of Scientific and Technological Achievements of Chinese Academy of Sciences(Hongguang Project).
文摘The effects of operating pressure on the gas-solid flow characteristics in a pressurized circulating fluidized bed(CFB)gasification system were studied by experiment and simulation.Elevated operating pressure was found to increase the particle uniformity in the axial and radial directions.Experiments and simulations both showed that as the operating pressure increased,the pressure drops along the riser height decreased.The experimental pressure drops at the same locations decreased when the operating pressure increased,but the opposite trend was observed in the simulation results.A proper drag model must be developed for the accurate simulation of pressurized CFB operation,and the accuracy of electrical capacitance tomography(ECT)measurement and cross-correlation analysis should be improved for better prediction of the particle circulation flux.
文摘The dynamic features of an agglomerate bubbling fluidization of nanoparticles were investigated through the analysis of pressure fluctuations. Experiments were carried out in a lab-scale fluidized bed at ambient conditions using 10-15 nm silica nanoparticles without any surface modification. Pressure fluctuation signals were processed in both frequency and time-frequency domains to characterize the behavior of various scales of phenomena (i.e.. macro-, meso-, and micro-structures) during fluidization. Due to the aggregation of nanoparticles, three separate broad peaks were observed in the frequency spectra of the pressure signals measured in the bubbling fluidized bed of nanoparticles. A non-intrusive method based on the decoupling of pressure fluctuations recorded simultaneously in the plenum and in the bed was used to determine the approximate size of the bubbles in the bed.
文摘The article presents an effort to create dimensionless scaling correlations of the overall bed porosity in the case of magnetically assisted fluidization in a tapered vessel with external transverse magnetic field. This is a stand of portion of new branch in the magnetically assisted fluidization recently created concerning employment of tapered vessels. Dimensional analysis based on "pressure transform" of the initial set of variables and involving the magnetic granular Bond number has been applied to develop scaling relationships of dimensionless groups representing ratios of pressures created by the fluid flow, gravity and the magnetic field over an elementary volume of the fluidized bed. Special attention has been paid on the existing data correlations developed for non-magnetic beds and the links to the new ones especially developed for tapered magnetic counterparts. A special dimensionless variable Xp = (Ar△Dbt)1/3√RgMQ combining Archimedes and Rosensweig numbers has been conceived for porosity correlation. Data correlations have been performed by power-law, exponential decay and asymptotic functions with analysis of their adequacies and accuracies of approximation.
文摘Gas-solid fluidized beds are widely considered as nonlinear and chaotic dynamic systems. Pressure fluc- tuations were measured in a fluidized bed of 0.15 m in diameter and were analyzed using multiple approaches: discrete Fourier transform (DFT), discrete wavelet transform (DWT), and nonlinear recur- rence quantification analysis (RQA). Three different methods proposed that the complex dynamics of a fluidized bed system can be presented as macro, meso and micro structures. It was found from DFT and DWT that a minimum in wide band energy with an increase in the velocity corresponds to the transition between macro structures and finer structures of the fluidization system. Corresponding transition veloc- ity occurs at gas velocities of 0.3, 0.5 and 0.6 m]s for sands with mean diameters of 150, 280 and 490/~m, respectively. DFT, DWT, and RQA could determine frequency range of0-3.125 Hz for macro, 3. ! 25-50 Hz for meso, and 50-200 Hz for micro structures. The RQA showed that the micro structures have the least periodicity and consequently their determinism and laminarity are the lowest. The results show that a combination of DFT, DWT, and RQA can be used as an effective approach to characterize multi-scale flow behavior in gas-solid fluidized beds.
基金the financial support of the Strategic Priority Research Program of the Chinese Academy of Sciences(No.XDA07030100)the Technology Planning Project of Jiangxi Province(No.20122BBG70087)financial contributions from the Chongqing Science and Technology Commission(No.2011AC4068)
文摘In this paper, the pressure fluctuation in a fluidized bed was measured and processed via standard devia- tion and power spectrum analysis to investigate the dynamic behavior of the transition from the bubbling to turbulent regime. Two types (Geldart B and D) of non-spherical particles, screened from real bed materials, and their mixture were used as the bed materials. The experiments were conducted in a semi- industrial testing apparatus. The experimental results indicated that the fluidization characteristics of the non-spherical Geldart D particles differed from that of the spherical particles at gas velocities beyond the transition velocity Uo The standard deviation of the pressure fluctuation measured in the bed increased with the gas velocity, while that measured in the plenum remained constant. Compared to the coarse particles, the fine particles exerted a stronger influence on the dynamic behavior of the fluidized bed and promoted the fluidization regime transition from bubbling toward turbulent. The power spectrum of the pressure fluctuation was calculated using the auto-regressive (AR) model; the hydrodynamics of the flu- idized bed were characterized by the major frequency of the power spectrum of the pressure fluctuation. By combining the standard deviation analysis, a new method was proposed to determine the transition velocity Uk via the analysis of the change in the major frequency. The first major frequency was observed to vary within the range of 1.5 to 3 Hz.
文摘This paper presents the results of an ongoing investigation into transient pressure pulses using Shan- non entropy. Pressure fluctuations (produced by gas-solid two-phase flow during fluidized dense-phase conveying) are recorded by pressure transducers installed at strategic locations along a pipeline. This work validates previous work on identifying the flow mode from pressure signals (Mittal, Mallick, & Wypych, 2014). Two different powders, namely fly ash (median particle diameter 45 μm, particle den- sity 1950 kg/m3. loosely poured bulk density 950 kg/m3) and cement (median particle diameter 15 p,m, particle density 3060 kg/m3, loosely poured bulk density 1070 kg/m3), are conveyed through different pipelines (51 mm I.D. × 70 m length and 63 mm I.D. × 24 m length). The transient nature of pressure fluc- tuations (instead of steady-state behavior) is considered in investigating flow characteristics. Shannon entropy is found to increase along straight pipe sections for both solids and both pipelines. However, Shannon entropy decreases after a bend. A comparison of Shannon entropy among different ranges of superficial air velocity reveals that high Shannon entropy corresponds to very low velocities (i.e. 3-5 m/s) and very high velocities (i.e. 11-14 m/s) while low Shannon entropy corresponds to mid-range velocities (i.e. 6-8 m/s).
基金the Natural Sciences and Engineering Research Council of Canada for supporting this project financially
文摘Most hydrodynamic fluidized bed models, including CFD codes, neglect any effects of the plenum chamber volume. Experiments were performed in a 0.13 m ID fluidization column to determine plenum chamber volume effects on fluidized bed hydrodynamics for FCC and glass particles. Two low-pressure-drop distributors were used, one with a single orifice, and the other with 33 orifices and the same total open area as the single orifice. The results show two peaks in the frequency spectra for the single-orifice distributor, one representing bubble eruption at the bed surface and the other of higher frequency corresponding to the bubbling frequency at the distributor. The latter decreased slightly with increasing plenum volume and with increasing bed depth. For the multi-orifice distributor, broad frequency spectra from pressure measurements became narrower and moved towards higher frequency with decreasing plenum volume.
文摘Fluidized beds frequently involve non-spherical particles, especially if biomass is present. For spheri- cal particles, numerous experimental investigations have been reported in the literature. In contrast, complex-shaped particles have received much less attention. There is a lack of understanding of how par- ticle shape influences flow-regime transitions. In this study, differently shaped Geldart group D particles are experimentally examined. Bed height, pressure drop, and their respective fluctuations are analyzed. With increasing deviation of particle shape from spheres, differences in flow-regime transitions occur with a tendency for the bed to form channels instead of undergoing smooth fluidization. The correlations available in the literature for spherical particles are limited in their applicability when used to predict regime changes for complex-shaped particles. Hence, based on existing correlations, improvements are derived.
文摘The hydrodynamics of a gas-liquid-solid fluidized bed was investigated by applying the S statistics method to pressure fluctuations measured under various operating conditions in a laboratory-scale bed. S statistics tests reveal the existence of three transition velocities, especially at low gas velocities. Four distinct fluidization regimes, namely, the compacted bed, agitated bed and coalesced and discrete bubble regimes were detected. A comparison of reconstructed attractors of pressure fluctuations measured at different axial positions along the riser and with various solid loadings showed significant differences in the signals compared before fluidization, especially at minimum liquid agitation velocity. Close to the minimum liquid fluidization velocity and high liquid velocities, the variation in particle size has an insignificant effect on the bed hydrodynamics. Therefore, S statistics is a reliable method to demar- cate different fluidization regimes and to characterize the influence of various operating conditions on the hydrodynamics of gas-liquid-solid fluidized beds. The method is applicable in large-scale industrial installations to detect dynamic changes within a bed, such as regime transitions or agglomeration.