Vibration attenuation performance of wind turbine tower using a prestressed tuned mass damper under seismic excitation

With the rapid development of large megawatt wind turbines,the operation environment of wind turbine towers(WTTs)has become increasingly complex.In particular,seismic excitation can create a resonance response and cause excessive vibration of the WTT.To investigate the vibration attenuation performance of the WTT under seismic excitations,a novel passive vibration control device,called a prestressed tuned mass damper(PS-TMD),is presented in this study.First,a mathematical model is established based on structural dynamics under seismic excitation.Then,the mathematical analytical expression of the dynamic coefficient is deduced,and the parameter design method is obtained by system tuning optimization.Next,based on a theoretical analysis and parameter design,the numerical results showed that the PS-TMD was able to effectively mitigate the resonance under the harmonic basal acceleration.Finally,the time-history analysis method is used to verify the effectiveness of the traditional pendulum tuned mass damper(PTMD)and the novel PS-TMD device,and the results indicate that the vibration attenuation performance of the PS-TMD is better than the PTMD.In addition,the PS-TMD avoids the nonlinear effect due to the large oscillation angle,and has the potential to dissipate hysteretic energy under seismic excitation.

Theoretical Analysis on Deflection and Bearing Capacity of Prestressed Bamboo-Steel Composite Beams

A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shear deformation.Furthermore,the calculation model for flexural capacity is proposed considering the two stages of loading.The theoretical results are verified with 8 specimens considering different prestressed load levels,load schemes,and prestress schemes.The results indicate that the proposed theoretical analysis provides a feasible prediction of the deflection and bearing capacity of bamboo-steel composite beams.For deflection analysis,the method considering the slippage and shear deformation provides better accuracy.The theoretical method for bearing capacity matches well with the test results,and the relative errors in the serviceability limit state and ultimate limit state are 4.95%and 5.85%,respectively,which meet the accuracy requirements of the engineered application.

Laminated Solid Timber Slab with Transverse Prestressing Using the Strategy of Interleaved Vertical Displacement of Lamellae

This article presents a study on the structural behavior of transversely prestressed laminated timber slabs,focusing on an innovative approach:vertically misaligned lamellae.This misalignment,achieved by sliding vertically the wooden lamellae rather than aligning them,enhances the slab’s cross-section moment of inertia,thereby improving load-bearing capacity and stiffness.Testing involved two groups of structural size specimens:one with vertically aligned lamellae(control group)and the other with misaligned lamellae(study group).Results showed the study group exhibited 42%superior stiffness and 10%less load capacity compared to the control.Failures typically occurred individually in the lamellae,particularly in those with defects or lower modulus of elasticity,concentrated in the middle third of the slabs’free span where tensile stresses peak.Despite a higher number of failed lamellae,the study group demonstrated promising performance.Analysis of prestressing bar indicated no damage at all in the thread,suggesting potential for reducing bar diameter.These findings offer crucial insights into applying these slabs in timber construction as well as to any kind of construction.

Discussion on Detection and Evaluation of Simply Supported Prestressed Concrete Small Box Girder Bridge After a Fire

The article takes a simply supported prestressed concrete small box girder bridge project as an example for inspection and evaluation after a fire incident.This includes appearance detection,concrete color hardness detection,concrete strength detection,concrete surface damage layer detection,reinforcement protective layer detection,and concrete carbonation detection.It is hoped that this analysis can be used as a reference for the detection and evaluation of future bridge projects with fire incidents to smoothen its subsequent repair and maintenance.

Model test of the stability degradation of a prestressed anchored rock slope system in a corrosive environment

The long-term stability of a prestressed anchored slope might be influenced by the durability of the anchorage structure.To understand long-term stability of anchored rock slopes,the research presented herein evaluated the performance evolution of a prestressed anchored bedding slope system in a corrosive environment by model test.The corrosion process in a prestressed anchor bar was monitored in terms of its open-circuit potential(OCP),corrosion current density(CCD),and electrochemical impedance spectroscopy(EIS).The stability of the prestressed anchored slope was evaluated by monitoring changes in anchorage force and displacements.The experimental results show that prestress and oxygen could reduce the corrosion resistance of the anchor bar,and anchor bars in a chloride-rich environment are very susceptible to corrosion.Prestressed tendons in a corrosive environment suffer a loss of anchorage force,the prestress decreases rapidly after locking,and the rate thereof decreases until stabilising;in the later stage,corrosion leads to the reduction of the cross-sectional area of the steel bar which may cause the reduction in anchorage force again.Anchorage force controls the deformation and stability of the anchored slope,the prestress loss caused by later corrosion may lead to an increased rate of displacement and stability degradation of the prestressed anchored rock slope.

Study on damage-stress loss coupling model of rock and prestressed anchor cable in dry-wet environment

The loss of anchoring force is one of the problems to be solved urgently.The anchorage loss is a key factor causing the failure of anchoring engineering,so it is crucial to study the time-dependent variation of anchoring force.Alternating dry and wet(D-W)conditions have a significant effect on deformation of rock.The anchoring system is composed of anchoring components and rock mass,and thus rock deformation has a significant impact on the loss of anchoring force.Quantifying rock deformation under the effects of D-W cycles is a prerequisite to understanding the factors that influence loss of anchoring force in anchor bolts.In this study,we designed an anchoring device that enabled real-time monitoring of the variation in strain during D-W periods and rock testing.Nuclear magnetic resonance(NMR)measurements showed that under D-W conditions,the increment in porosity was smaller for prestressed rock than unstressed rock.The trends of prestress loss and strain variation are consistent,which can be divided into three characteristic intervals:rapid attenuation stage,slow attenuation stage and relatively stable stage.At the same stress level,the rate of stress loss and strain for the soaking specimen was the highest,while that of the dried specimen was the lowest.In the same D-W cycling conditions,the greater the prestress,the smaller the strain loss rate of the rock,especially under soaking conditions.The characteristics of pore structure and physical mechanical parameters indicated that prestress could effectively suppress damage caused by erosion related to D-W cycles.The study reveals the fluctuation behavior of rock strain and prestress loss under D-W conditions,providing a reference for effectively controlling anchoring loss and ideas for inventing new anchoring components.

Design on the Prestressed Concrete Frame Beam-column

A bidirectional ribbed concrete beam slab structure was widly adopted for the upper space of industrial buildings.To maintain ample space and minimize the presence of conventional columns,a bidirectional prestressed concrete beam is often employed.The intersection node of the prestressed concrete frame beam column was characterized by a high density of steel reinforcement,significant structural loads,and complex construction requirements.To ensure the quality,safety,and progress of prestressed frame beamcolumn intersection nodes during construction,this article proposed a new technology for constructing such nodes,which includes setting the tensioning and haunching ends of nodes at different positions,using ABAQUS finite element software to optimize the design of cross-sectional dimensions,conducting stress analysis simulations.

大跨径桥梁临时转体墩系统力学性能模拟研究

目的为减少大跨径桥梁施工对既有公路、铁路线运营的影响,达到缩短工期,节约成本的目的,提出一种临时墩体外转体法。方法利用Midas Fea软件建立转体球铰有限元模型,分析在匀速转动阶段、加速转动阶段和不平衡荷载下转体系统局部应力及位移。结果在匀速转动阶段,上、下球铰最大应力分别为39.79 MPa、49.34 MPa,满足强度要求;加速转动阶段,角加速度超过0.711 rad/s^(2)时,球铰最大应力超过设计值,角加速度超过0.716 rad/s^(2)时,球铰最大剪切应力超过设计值;在不平衡荷载作用下,转体球铰强度均满足设计要求,球铰边缘各点最大高差均小于加工规定限值。结论临时墩体外转体法可实现在最大偏心距下进行转体,施工完成后,球铰仍满足质量标准,可回收利用。

露顶式弧形闸门闸坝一体化静动力学研究

针对现有露顶式弧形闸门静动力学分析存在一定简化的问题,应用ANSYS有限元软件对比分析了闸门单体和闸坝一体化的静动力学特性。以某水电站溢流表孔弧形闸门瞬启工况为例,建立了考虑止水摩阻、支铰体系和预应力锚索的闸坝一体化有限元模型。研究结果发现:在静力学方面,两侧止水对闸门各钢结构构件应力影响不大,最大差值为14.08%;闸坝一体化得出的固定支铰应力分布较闸门单体更为合理;锚块对闸门结构整体位移结果影响较大,闸门单体整体位移<不考虑锚索预应力的闸坝一体化整体位移<考虑锚索预应力的整体位移。在动力学方面,考虑流固耦合效应下止水降低了闸门结构的各阶频率;预应力锚索对闸坝一体化动力特性影响较小。

桩锚结构体系在深基坑支护中应用研究

桩锚支护结构具有合理的受力形式,较大的支护刚度,节约施工空间等优点,在深基坑支护中被广泛应用,文中以定西市某基坑桩锚支护结构为依托,通过计算分析不同预应力锚索组合下,桩身最大内力与位移的影响,合理选取桩身及锚索参数,能有效降低桩身内力及桩顶位移,使护坡桩结构受力更合理,可取得更可靠经济的支护方案。

临近既有建筑物深基坑支护变形控制

随着城市的快速发展,人们对空间的要求越来越高,地面空间已被充分利用,地下空间开发利用已成为必然。而地下空间的开发利用必然涉及到基坑工程,本文结合重庆沙坪坝铁路枢纽改造工程中超大深基坑支护技术难点研究,分析了基坑开挖的变形机理,提出支护设计方案及施工监测控制,取得了良好的效果,可为城市立体空间利用的基坑支护提供有益参考。

风力发电机组预应力锚栓失效分析及对策研究

近些年,风力发电机组大量投入运行,风机倒塔事件在各地频发,其中一部分倒塔是由于预应力锚栓失效导致。通过对基础缺陷、工具使用不当、锚栓笼安装不到位等锚栓失效案例进行分析,提出了对基础缺陷所在位置打孔,采用无机和有机灌浆料对基础进行灌浆加固处理等相对应的解决方案以及预防措施,取得了良好的效果,具有进一步推广价值。

Experimental study on hysteretic behavior of prestressed truss concrete composite beams

This paper describes an experimental study of the hysteretic behavior of prestressed truss concrete composite beams （PTCCBs） under cyclic loading. Five beam models were designed and tested, in which the testing parameters include the global reinforcement index β0, the prestress level 2 and the ratio of stirrup ρsv in the potential plastic hinge zones. Based on the test results, the failure mode and hysteretic behavior of the tested models are obtained. In addition, the P-△ and sectional M-φ hysteretic models for the PTCCBs at the midspan are established. The P-△ hysteretic model shows good agreement with the test results.

Influence of confining prestress on the transition from interface defeat topenetration in ceramic targets

Replica scaled impact experiments with unconfined ceramic targets have shown that the transition velocity,i.e.,the impact velocity at which interface defeat ceases and ceramic penetration occurs,decreased as the length scale increased.A possible explanation of how this scale effect is related to the formation of a cone crack in the ceramic has been presented by the authors in an earlier paper.Here,the influence of confinement and prestress on cone cracking and transition velocity is investigated.The hypothesis is that prestress will suppress the formation and growth of the cone crack by lowering the driving stress.A set of impact experiments has been performed in which the transition velocity for four different levels of prestress has been determined.The transition velocities as a function of the level of confining prestress is compared to an analytical model for the influence of prestress on the formation and extension of the cone crack in the ceramic material.Both experiments and model indicate that prestress has a strong influence on the transition from interface defeat to penetration,although the model underestimates the influence of prestress.

Dynamic finite element model updating of prestressed concrete continuous box-girder bridge

The dynamic finite element model （FEM） of a prestressed concrete continuous box-girder bridge, called the Tongyang Canal Bridge, is built and updated based on the results of ambient vibration testing （AVT） using a real-coded accelerating genetic algorithm （RAGA）. The objective functions are defined based on natural frequency and modal assurance criterion （MAC） metrics to evaluate the updated FEM. Two objective functions are defined to fully account for the relative errors and standard deviations of the natural frequencies and MAC between the AVT results and the updated FEM predictions. The dynamically updated FEM of the bridge can better represent its structural dynamics and serve as a baseline in long-term health monitoring, condition assessment and damage identification over the service life of the bridge .

Theoretical analysis of natural frequency of externally prestressed concrete beam based on rigidity correction

A dynamic test on externally prestressed simply supported concrete beams separately with three typical types of tendon distributions was conducted. The results show that the natural frequencies of the beams increase with the increase in the prestressing force at the tensioning stage, and the natural frequencies decrease after the cracks occur in the beams. Following the calculation formula of natural frequency of externally prestressed beam, which was reported in a literature, the natural frequencies of the experimental beams are calculated, and big errors are found between the test results and the calculated ones of natural frequency values. As a result, this paper has tried to adopt two methods to correct the rigidity parameter of the concrete beam in the formula for natural frequency calculation, and to use the corrected formula to calculate the frequencies of the experimental beams. The calculation results indicate a good consistency with the experimental ones, which verifies the feasibility of the corrected formula.

Temperature and Stress Analysis of An Experimental Model of Prestressed Lightweight Concrete Platform

This paper presents an experimental study of a prestressed lightweight concrete platform model with a tank and for five steel-columns. This platform can be used not only for extraction but also for storage of oil and is suitable for the Bohai Sea and other shallow seas of China. The platform is subjected to temperature. load, or both. The corresponding temperature distribution. strains, cracks. and vulnerable parts of the platform are analyzed respectively. By use of the finite element method and empirical formulas, the temperature field of the model is analyzed. The results agree with the experimental results, thereby verifying! the reliability of these two calculating methods. The paper provides an experimental basis for the des sign of the bearing capacity and normal service state of prestressed concrete platforms.

Unified analogue method of effective prestress for post-prestressed tendon

In order to obtain the present effective prestress and its longitudinal distribution of prestressed tendon during the process of inspection and evaluation, a unified analogue method was put forward. Based on the theory for calculating instantaneous prestress loss of the tendons with complicated geometry, a universal numerical model was established. Therefore, the distribution of effective prestress could be simulated after recognizing the nominal coefficients of prestress loss with the obtained stress data of objective steel tendon. The numerical simulation results of a full-length tendon of a three-span continuous beam bridge show that the relative errors between the calculated value and the value in the code are within 5%, which meets the requirement for engineering application.

Reliability analysis of prestressed anchors in rock slopes of open-pit mines

Prestressed anchor cables are widely used for slope reinforcement,but the loss of prestress makes it difficult to guarantee the reinforcement effect.Anchor cable prestress degradation was considered as a stochastic process,and the probability density function of this process was established using gamma theory and impact theory respectively.Combined with the failure threshold,the probability density was integrated to find the time-dependent reliability of the anchor cable.Based on the monitoring data of the prestress degradation of the anchor cable,parameters in the probability density function were solved by the maximum likelihood method,and the time-varying reliability and service life of the anchor cable were obtained analytically.The applicability of two degradation theories,gamma stochastic process and impact theory,was compared.The results showed that the probability density curves of both degradation models were normally distributed and the error of reliability results did not exceed 0.06.The life prediction results of the gamma stochastic process were closer to the actual life of 400 h than the 500 h of the impact theory,and the probability curves of the anchor cable life also indicated that the impact theory overestimated the service life probability of the anchor cable.Taking the anchor cable reinforcement within the slope of the Dagushan open-pit mine as an example,and the results verify the feasibility of using gamma theory to predict the degradation of anchor cables and provides theoretical support for prevention of the degradation of anchor cables in the slope of an open-pit mine under the action of external forces.

Long-Term Bending Behaviour of Prestressed Glulam Bamboo-Wood Beam Based on Creep Effect

Creep is an important characteristic of bamboo and wood materials under long-term loading.This paper aims to study the long-term bending beha-viour of prestressed glulam bamboo-wood beam(GBWB).For this,14 pre-stressed GBWBs were selected and subjected to a long-term loading test for 60 days.Then,a comparative analysis was performed for the effects of pre-tension values,the number of pre-stressed wires,and long-term load on the stress variation of the steel wire and the long-term deflection of the beam midspan.The test results showed that with the number of prestressed wires increasing,the total stress of the steel wire in the beam midspan and the ratio of the long-term deflec-tion to the total deflection decreases decreased,but when the number of steel wires exceeded 4,the total stress and long-term deflection was less infuenced;with the pre-tension value increasing,the ratio of the total stress of the steel wire in the beam midspan and the ratio of the long-temm deflection to the total deflec-tion also decreased,but when the prestress force was greater than 3.975 kN,the:total stress and long-term deflection were less affected;with the other parameters unchanged,when the value of the long-term load increased,the total stress of the steel wire decreased,and the long-temm deflection of the beam midspan increased,which shall be more significant with the long-term load greater than 30%of the standard ultimate bearing capacity.After the test,the experimental data were fitted,and the creep coefficient was given.Finally,the long-term stiffness calcula-tion fommula of the pre-stressed GBWB based on creep effect was proposed.The research findings have certain theoretical significance and engineering value.