Explosion resistance performance of reinforced concrete box girder coated with polyurea:Model test and numerical simulation

To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.

Model test to investigate failure mechanism and loading characteristics of shallow-bias tunnels with small clear distance

Based on the similarity theory,a tunnel excavation simulation testing system under typical unsymmetrical loading conditions was established.Using this system,the failure mechanism of surrounding rock of shallow-bias tunnels with small clear distance was analyzed along with the load characteristics.The results show that:1) The failure process of surrounding rock of shallow-bias tunnels with small clear distance consists of structural and stratum deformation induced by tunnel excavation; Microfracture surfaces are formed in the tunnel surrounding rock and extend deep into the rock mass in a larger density; Tensile cracking occurs in shallow position on the deep-buried side,with shear slip in deep rock mass.In the meantime,rapid deformation and slip take place on the shallow-buried side until the surrounding rocks totally collapse.The production and development of micro-fracture surfaces in the tunnel surrounding rock and tensile cracking in the shallow position on the deep-buried side represent the key stages of failure.2) The final failure mode is featured by an inverted conical fracture with tunnel arch as its top and the slope at tunnel entrance slope as its bottom.The range of failure on the deep-buried side is significantly larger than that on the shallow-buried side.Such difference becomes more prominent with the increasing bias angle.What distinguishes it from the "linear fracture surface" model is that the model proposed has a larger fracture angle on the two sides.Moreover,the bottom of the fracture is located at the springing line of tunnel arch.3) The total vertical load increases with bias angle.Compared with the existing methods,the unsymmetrical loading effect in measurement is more prominent.At last,countermeasures are proposed according to the analysis results: during engineering process,1) The surrounding rock mass on the deep-buried side should be reinforced apart from the tunnel surrounding rock for shallow-buried tunnels with small clear distance; moreover,the scope of consolidation should go beyond the midline of tunnel(along the direction of the top of slope) by 4 excavation spans of single tunnel.2) It is necessary to modify the load value of shallow-bias tunnels with small clear distance.

Model test of the stability degradation of a prestressed anchored rock slope system in a corrosive environment

The long-term stability of a prestressed anchored slope might be influenced by the durability of the anchorage structure.To understand long-term stability of anchored rock slopes,the research presented herein evaluated the performance evolution of a prestressed anchored bedding slope system in a corrosive environment by model test.The corrosion process in a prestressed anchor bar was monitored in terms of its open-circuit potential(OCP),corrosion current density(CCD),and electrochemical impedance spectroscopy(EIS).The stability of the prestressed anchored slope was evaluated by monitoring changes in anchorage force and displacements.The experimental results show that prestress and oxygen could reduce the corrosion resistance of the anchor bar,and anchor bars in a chloride-rich environment are very susceptible to corrosion.Prestressed tendons in a corrosive environment suffer a loss of anchorage force,the prestress decreases rapidly after locking,and the rate thereof decreases until stabilising;in the later stage,corrosion leads to the reduction of the cross-sectional area of the steel bar which may cause the reduction in anchorage force again.Anchorage force controls the deformation and stability of the anchored slope,the prestress loss caused by later corrosion may lead to an increased rate of displacement and stability degradation of the prestressed anchored rock slope.

Full-scale model tests and nonlinear analysis of prestressed concrete simply supported box girders

Full-scale model tests were carried out on a 30 m span prestressed concrete box girder and a 20 m span prestressed concrete hollow slab. Failure models were prestressed reinforcement tensile failure and crashing of roof concrete, respectively. The ductility indexes of the box girder and hollow slab were 1.99 and 1.23, respectively, according to the energy viewpoint. Based on the horizontal section hypothesis, the nonlinear computation procedure was established using the limited banding law, and it could carry out the entire performance analysis including the unloading, mainly focusing on the ways to achieve the unloading curves computation through stress-strain, moment-curvature and load-displacement curves. Through the procedure, parameters that influence on the bearing capacity, deformation performance and ductility of the structures were analyzed. Those parameters were quantity of prestressed reinforcement and tension coefficients of prestressed reinforcement. From the analysis, some useful conclusions can be obtained.

Model tests on XCC-piled embankment under dynamic train load of high-speed railways

Piled embankments,which offer many advantages,are increasingly popular in construction of high-speed railways in China.Although the performance of piled embankment under static loading is well-known,the behavior under the dynamic train load of a high-speed railway is not yet understood.In light of this,a heavily instrumented piled embankment model was set up,and a model test was carried out,in which a servo-hydraulic actuator outputting M-shaped waves was adopted to simulate the process of a running train.Earth pressure,settlement,strain in the geogrid and pile and excess pore water pressure were measured.The results show that the soil arching height under the dynamic train load of a high-speed railway is shorter than under static loading.The growth trend for accumulated settlement slowed down after long-term vibration although there was still a tendency for it to increase.Accumulated geogrid strain has an increasing tendency after long-term vibration.The closer the embankment edge,the greater the geogrid strain over the subsoil.Strains in the pile were smaller under dynamic train loads,and their distribution was different from that under static loading.At the same elevation,excess pore water pressure under the track slab was greater than that under the embankment shoulder.

Long-Term Loading Test of Reinforced Glulam Beam

Due to creep characteristics of wood,long-term loading can cause a significant stress loss of steel bars in rein-forced glulam beams and high long-term deflection of the beam midspan.In this study,15 glulam beams were subjected to a 90-day long-term loading test,and the effects of long-term loading value,reinforcement ratio and prestress level on the stress of steel bars,midspan long-term deflection,and other parameters were compared and analyzed.The main conclusions drawn from this study were that the long-term deflection of the reinforced glulam beams accounted for 22.5%,20.6%,and 18.2%of the total deflection respectively when the loading value was 20%,30%,and 40%of the estimated ultimate load under the long-term loading.The higher the loading level was,the smaller the proportion of the long-term deflection in the total deflection was.Compared with ordinary glulam beams,the long-term deflection of the reinforced glulam beam was even smaller.Under the condition of the constant loading level,the total stress value of the steel bars decreased by 17.5%,13.6%,and 9.1%,and the proportion of the long-term deflection of the beam midspan in the total deflection was 26.9%,24.2%,and 20.6%respectively when the reinforcement ratio was 2.05%,2.68%,and 3.39%.With the increase of the reinfor-cement ratio,the stress loss of the steel bars decreased,and the proportion of the long-term deflection decreased as well.When other conditions remained constant and the prestress level of the steel bars was 0 MPa,30 MPa,and 60 MPa,the total stress value of the steel bars decreased by 9.1%,9.4%,and 10.2%,respectively,and the propor-tion of the long-term deflection in the total deflection was 20.6%,26.1%,and 64.9%,respectively.With the increase of the prestress value,the stress loss of the steel bars increased,and the proportion of the long-term deflection increased as well.

A model test system with a dynamic load device for geotechnical engineering in cold regions

A model test system with a dynamic load device for geotechnical engineering in cold regions is presented. This system consists of a model test tank, a refrigeration device and temperature controller, a dynamic load device, together with sensors and data loggers for detecting stress, deformation, and temperature changes. The system can accommodate soil blocks up to 3 m in length, 2.5 m in width, and 1 m in height. The lowest temperature provided by the refrigeration device is -20 ℃. The maximum load provided by the dynamic load device is 100 kN and the vibration fi＇equency of the dynamic load can range from 0.1 to 10 Hz. A number of waveforms, such as sine waves, rectangular waves, triangle waves, and other user-defined waves can be generated by the dynamic load device controller.

A thermal stress loading technique for large-sized hot dry rock mechanical tests

Testing of large-sized specimens is becoming increasingly important in deep underground rock mechanics and engineering.In traditional mechanical loading,stresses on large-sized specimens are achieved by large host frames and hydraulic pumps,which could lead to great investment.Low-cost testing machines clearly always have great appeal.In this study,a new approach is proposed using thermal expansion stress to load rock specimens,which may be particularly suitable for tests of deep hot dry rock with high temperatures.This is a different technical route from traditional mechanical loading through hydraulic pressure.For the rock mechanics test system of hot dry rock that already has an investment in heating systems,this technology may reduce the cost of the loading subsystem by fully utilizing the temperature changes.This paper presents the basic principle and a typical design of this technical solution.Preliminary feasibility analysis is then conducted based on numerical simulations.Although some technical details still need to be resolved,the feasibility of this loading approach has been preliminarily confirmed.

Full-scale pullout tests of rock anchors in a limestone quarry focusing on bond failure at the anchor-grout and grout-rock interfaces

Rock anchors are a common safety measure for stabilising large-scale infrastructure,such as bridge towers,retaining walls,rock slopes and windmills.There are four principal failure modes for rock anchors:(a)tensile failure of the steel anchor,(b)anchor-grout interface failure,(c)grout-rock interface failure,and(d)rock mass uplift.Field tests were performed in a limestone quarry.These tests were designed to test failure modes B and C through pullout.In the tests of failure mode B,the shear stress on the anchor-grout interface is the largest at the top of the grout column and attenuates towards the distal end for small loads.The shear stress becomes uniformly distributed when the applied load is approximately 50%of the ultimate pullout load.The anchors designed to test failure mode C were installed with an endplate and had a higher toughness than the straight bar anchors.The shear stress on the grout-rock interface is the largest at the endplate and attenuates upward before slip starts along the interface.When the ultimate pullout load is reached,and the grout column starts to slip,the shear stress is approximately constant.The bond shear strength on the anchor-grout interface was approximately 20%of the uniaxial compressive strength of the grout,and the bond strength of the grout-rock interface was around 5%for that of the grout.The grout-rock interface is likely determined by whichever is weaker,the grout or the rock.

Research of Interaction Force Coefficients Based on Model Test in Loading Condition

It is very difficult,for the component-type ship mathematical model,to estimate the interaction force coefficients among the hull,propeller and rudder. Some coefficients such as wake fraction and flow straightening coefficient were studied from the model tests in diffierent loading conditions and the normal force of rudder was tested in captive model tests to obtain the coefficients. From these results of the tests,the flow straightening coefficients increase with the increase of trims or drafts. Similarly,wake fraction coefficients are larger for the large drafts,however,become small as the trims increase. The resistance is obviously different in fully loaded condition with the trims by stern,however ,the difference is not evident when the draft decreases and the bulbous bow is above the water surface.

Model tests and corresponding numerical simulations on cave model subjected to thermo-mechanical loading

Geological repository of high-level nuclear waste(HLNW),the most feasible approach for the safe and permanent treatment of HLNW without human intervention,has been investigated for years by many researchers.In some countries,real facilities for the geo-logical repository are already under construction.In Japan,however,due to complicated geologic conditions,especially underground water and fractured rock masses,and the high risk of natural disasters,ensuring the long-term stability of the method remains a struggle.The influential factors include underground water,heat generation from radioactive waste,and thermal and chemical weathering of the surrounding rock mass as a natural barrier.It is difficult to estimate and verify the long-term stability for up to one hundred thousand years,a complicated thermal-hydraulic-mechanical-chemical coupling behavior,via any field test.The objective of the study is to develop a numerical method for predicting the long-term stability of geological repositories.As the first step toward realizing this objec-tive,heating and loading tests on cave model made of man-made rock specimens that are composed of diatoms,gypsum,and water,which are viscoplastic materials,were conducted,based on which a newly proposed numerical method with finite element method(FEM)was used to describe the thermal,mechanical,and time-dependent behavior of the model tests for a geological repository.To ensure the accuracy of the numerical calculations,all the material parameters in the thermoelasto-viscoplastic model with consideration of overconsolidation,the structure,and the influence of intermediate stress were determined via triaxial compression/creep tests under various temperatures,confining stresses,and loading rates.Finally,the validity of the numerical method was demonstrated by model tests over a limited time span.

Lateral earth pressure of granular backfills on retaining walls with expanded polystyrene geofoam inclusions under limited surcharge loading

Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,the failure mode and the earth pressure acting on the rigid retaining wall with EPS geofoam inclusions and granular backfills(henceforth referred to as EPS-wall),under limited surcharge loading are investigated through two-and three-dimensional model tests.The testing results show that different from the sliding of almost all the backfill in the EPS-wall under semi-infinite surcharge loading,only an approximately triangular backfill slides in the wall under limited surcharge loading.The distribution of the lateral earth pressure on the EPS-wall under limited surcharge loading is non-linear,and the distribution changes from the increase of the wall depth to the decrease with the increase of the limited surcharge loading.An approach based on the force equilibrium of a differential element is developed to predict the lateral earth pressure behind the EPS-wall subjected to limited surcharge loading,and its performance was fully validated by the three-dimensional model tests.

Model Testing for Ship Hydroelasticity: A Review and Future Trends

Conducting model experiments is an effective and reliable way in the investigation of ship hydrodynamic and hydroelastic behaviors. A survey of model testing techniques for ship hydroelasticity and its prospect are presented in this paper. The research highlights with respect to ship hydroelasticity and key points in model testing are summarized at first. Then testing techniques including laboratory tank test and full-scale sea trial are reviewed, and both their advantages and disadvantages are analyzed comprehensively. Based on the conventional testing approaches, a state-of-the-art testing approach which includes performing tests using large-scale model at sea is proposed. Furthermore, recommendations towards the further development of ship hydroelasticity tests are forecasted and discussed.

Testing and modeling of cyclically loaded rock anchors

The Norwegian Public Roads Administration(NPRA) is planning for an upgrade of the E39 highway route at the westcoast of Norway. Fixed links shall replace ferries at seven fjord crossings. Wide spans and large depths at the crossings combined with challenging subsea topography and environmental loads call for an extension of existing practice. A variety of bridge concepts are evaluated in the feasibility study. The structures will experience significant loads from deadweight, traffic and environment. Anchoring of these forces is thus one of the challenges met in the project. Large-size subsea rock anchors are considered a viable alternative. These can be used for anchoring of floating structures but also with the purpose of increasing capacity of fixed structures. This paper presents first a thorough study of factors affecting rock anchor bond capacity. Laboratory testing of rock anchors subjected to cyclic loading is thereafter presented. Finally, the paper presents a model predicting the capacity of a rock anchor segment, in terms of a ribbed bar, subjected to a cyclic load history. The research assumes a failure mode occurring in the interface between the rock anchor and the surrounding grout. The constitutive behavior of the bonding interface is investigated for anchors subjected to cyclic one-way tensile loads. The model utilizes the static bond capacity curve as a basis, defining the ultimate bond sbuand the slip s1 at τ. A limited number of input parameters are required to apply the model. The model defines the bond-slip behavior with the belonging rock anchor capacity depending on the cyclic load level(τcy/τ), the cyclic load ratio(R= τcy/τcy), and the number of load cycles(N). The constitutive model is intended to model short anchor lengths representing an incremental length of a complete rock anchor.

Prestressed tensioning method and its application to testing anchor stress of anchor cables for side-slope stabilization

The anchor stress extent of a prestress anchor cable project has a direct relation with the project safety and performance. Prestressed tensioning method is a kind of nondestructive testing method, by which a reverse stretching load is applied on the external exposure section of anchor cable under construction or in service, and then the elongation variation of stress bars is measured to determine the anchor stress. We elaborated the theory and testing mechanism of prestressed tensioning method, and systematically studied key issues during the prestressed tensioning process of anchor cable by using physical model test, including the composition of tension stress-elongation curve, the variation of anchor stress, the compensation of locked anchor stress, and the judgment of anchor stress, and verified the theory feasibility of prestressed tensioning method. A case study on slope anchor cable of one highway project was conducted to further discuss on the test method, operation procedures and judgment of prestressed tensioning method on obtaining anchor stress, and then the test data of three situations were analyzed. The result provides a theoretical basis and technical base for the application of prestressed tensioning method to the evaluation of construction quality and operation conditions of anchor cable project.

METHOD FOR FAST TEST OF PRESTRESSED CONCRETE VOIDED SLAB (V.S)

By practical experience and lots of actuel data on tens of prestressed concrete V.S,maximum strains of the midspan sectional concrete and Strains of tendon are calculated according to actual date of the midspan deflection Yc, which show Whole structual working condition, as a result,method for fast test of structural bearing capacity can be deduced, which would make determining bearing capacity of existing prestressed concrete V.S simply and quickly, and also improve accuracy of cxperimental results and working efficiency.

Mechanical performance evaluation of a new type of cable-stayed beam-arch combination bridge based on field tests

In order to study the mechanical performance of a new type of cable-stayed beam-arch combination bridge, the results of field static and dynamic load tests are comparatively analyzed with numerical results based on the Jingyi bridge straddling the Daxi River in Yixing. First, the test scheme, tasks, the corresponding measure method, as well as the relevant codes are described. Secondly, two sets of three- dimensional finite element models are established. One is Ansys which uses the solid element and the other is Midas which adopts the beam element. Finally, the experimental and analytical results are comparatively analyzed, and they show an agreement with each other. The results show that the bridge possesses adequate load-carrying capacity under all static load cases, but the capacity of dissipating external input energy is insufficient due to the relatively smaller damping ratio. The study results can provide a reference for further study and optimization of this type of bridge. Calibrated finite-element models that reflect the real conditions can be used as a baseline for future maintenance of the bridge.

Dynamic finite element model updating of prestressed concrete continuous box-girder bridge

The dynamic finite element model （FEM） of a prestressed concrete continuous box-girder bridge, called the Tongyang Canal Bridge, is built and updated based on the results of ambient vibration testing （AVT） using a real-coded accelerating genetic algorithm （RAGA）. The objective functions are defined based on natural frequency and modal assurance criterion （MAC） metrics to evaluate the updated FEM. Two objective functions are defined to fully account for the relative errors and standard deviations of the natural frequencies and MAC between the AVT results and the updated FEM predictions. The dynamically updated FEM of the bridge can better represent its structural dynamics and serve as a baseline in long-term health monitoring, condition assessment and damage identification over the service life of the bridge .

Numerical Analysis of Ice Rubble with a Freeze-Bond Model in Dilated Polyhedral Discrete Element Method

Freezing in ice rubble is a common phenomenon in cold regions,which can consolidate loose blocks and change their mechanical properties.To model the cohesive effect in frozen ice rubble,and to describe the fragmentation behavior with a large external forces exerted,a freeze-bond model based on the dilated polyhedral discrete element method(DEM)is proposed.Herein,imaginary bonding is initialized at the contact points to transmit forces and moments,and the initiation of the damage is detected using the hybrid fracture model.The model is validated through the qualitative agreement between the simulation results and the analytical solution of two bonding particles.To study the effect of freeze-bond on the floating ice rubble,punch-through tests were simulated on the ice rubble under freezing and nonfreezing conditions.The deformation and resistance of the ice rubble are investigated during indenter penetration.The influence of the internal friction coefficient on the strength of the ice rubble is determined.The results indicate that the proposed model can properly describe the consolidated ice rubble,and the freeze-bond effect is of great significance to the ice rubble properties.

串珠状溶洞数量影响灌注桩顶部水平受拉特性试验研究

采用室内模型试验,对比研究串珠状溶洞数量对灌注桩顶部水平受拉特性的影响,为岩溶强发育区嵌岩桩的水平承载力设计提供试验依据.结果表明:1)桩顶水平荷载相同时,上部土层段桩身水平位移、桩身弯矩(峰值)、桩侧土抗力随溶洞数量的增多而增大,单桩水平承载力随溶洞数量增多而明显减弱.2)上部土层段桩身水平位移随桩顶水平荷载增大而增大,桩顶水平位移最大,嵌岩段很小甚至为0;弯矩M-深度z曲线整体呈抛物线形,桩身弯矩在土岩界面和上层溶洞与底板界面呈现2个峰值,弯矩的变化仅仅影响到上层溶洞及其底板,第2层溶洞及其以下的弯矩几乎为0,土岩界面弯矩最大、截面最危险;土抗力p-深度z曲线呈“凸肚”形.3)溶洞数量增加,位置越高,p-y曲线越容易收敛,可以采用p/pub=α(y/y50)β拟合土层段的桩身p-y曲线.溶洞数量对α与β值变化幅度的影响较小,α与β值变化幅度体现p-y曲线随深度变化的敏感度,两者敏感度随溶洞数量增多而增大.4)工程桩刺穿串珠状溶洞时,为了提高单桩水平抗拉能力,建议采用注浆法改善上部岩土性质,加大土岩界面处桩身配筋率,并将桩身嵌入上层溶洞底板一定深度,防止基桩在土岩界面处发生弯曲破坏.