A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shea...A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shear deformation.Furthermore,the calculation model for flexural capacity is proposed considering the two stages of loading.The theoretical results are verified with 8 specimens considering different prestressed load levels,load schemes,and prestress schemes.The results indicate that the proposed theoretical analysis provides a feasible prediction of the deflection and bearing capacity of bamboo-steel composite beams.For deflection analysis,the method considering the slippage and shear deformation provides better accuracy.The theoretical method for bearing capacity matches well with the test results,and the relative errors in the serviceability limit state and ultimate limit state are 4.95%and 5.85%,respectively,which meet the accuracy requirements of the engineered application.展开更多
In order to validate the accuracy of nonlinear fire simulation programs,comparison analysis is carried out between simulation and experiment induced from small-scale specimens,and then fire resistance of large-scale p...In order to validate the accuracy of nonlinear fire simulation programs,comparison analysis is carried out between simulation and experiment induced from small-scale specimens,and then fire resistance of large-scale prestressed concrete slabs is further investigated through parameter expansion.The influences on fire resistance ratings controlled by deflection are explored and discussed,including effective span,concrete cover thickness,load level,prestress degree,effective prestress,composite reinforcement index and other factors.The calculated results indicate that fire resistance ratings of large-scale bonded prestressed concrete simply supported slabs are bigger than those of small-scale ones.Finally,the calculation formulas of fire resistance ratings controlled by deflection are established,which rationally consider the influence of effective span,concrete cover thickness,load level,composite reinforcement index and so on key factors.展开更多
The flexural behaviors of continuous fully and partially prestressed steel fiber reinforced high strength concrete beams are studied by experiment and nonlinear finite element analysis. Three levels of partial prestre...The flexural behaviors of continuous fully and partially prestressed steel fiber reinforced high strength concrete beams are studied by experiment and nonlinear finite element analysis. Three levels of partial prestress ratio (PPR) are considered, and three pairs of two-span continuous beams with box sections varying in size are designed. The major parameters involved in the study include the PPR and the fiber location. It is concluded that the prestressed high strength concrete beam exhibits satisfactory ductility; the influences of steel fiber on the crack behaviors for partially prestressed beams are not as obvious as those for fully prestressed ones; steel fibers can improve the structural stiffness after cracking for fully prestressed high strength concrete beams; the moment redistribution from mid-span to intermediate support in the first stage should be mainly considered in practical design.展开更多
This paper presents the results of four partially prestressed ultra-high strength concrete beams in flexure. The test results are used to evaluate the effects of prestressing tendon depth and area on flexure behavior ...This paper presents the results of four partially prestressed ultra-high strength concrete beams in flexure. The test results are used to evaluate the effects of prestressing tendon depth and area on flexure behavior of specimen beams. The test results indicate that: the cracking load,yielding load,peak load and stiffness postcracking of specimen beams are enhanced by reducing prestressing tendon depth or increasing prestressing tendon area, and the flexural ductility is improved by increasing prestressing tendon depth or reducing prestressing tendon area. The effect of complex reinforcement index considering the strength of the equivalence principle and the reinforcement position on loading levels under serviceability limit state,flexural strength and displacement ductility factor are studied. The influence coefficient of prestressing tendon kpis introduced in the complex reinforcement index. As the complex reinforcement index increases, the loading levels under serviceability limit state and flexural strength increases linearly,and the displacement ductility factor decreases linearly. The test results also verify the conventional beam flexural theory based on the plane cross-section assumption for predicting ultimate flexural strength of partially prestressed ultra-high strength concrete beams is valid. After the introduction of the coefficient kp,the calculation method of cracks in code for design of concrete structure in china are appropriated for the specimen beams.展开更多
When the gearbox body interference is connected to the ring gear, prestressing occurs in the ring gear, which has a significant impact on the strength and life of the gear. Research on the prestressing of the inner ri...When the gearbox body interference is connected to the ring gear, prestressing occurs in the ring gear, which has a significant impact on the strength and life of the gear. Research on the prestressing of the inner ring gear is in the preliminary stage, and the distribution rule of the prestressing and the influence of each parameter on the interference prestressing have not been derived. In this paper, based on the method of calculating the prestressing of the thick cylinder in interference fit, the ring gear is found to be equivalent to a thick cylinder, and the distribution rule of prestressing of the ring gear in the interference fit is inferred. Then, by modeling and analyzing the gearbox body and ring gear in the interference fit using ABAQUS, the distribution rule of prestressing the ring gear in the interference fit is obtained through a numerical simulation. Finally, the prestressing of the ring gear in the interference fit is measured using X-ray di raction, and the distribution rule of prestressing of the ring gear in the interference fit is obtained through analysis. Compared with the distribution rule of prestressing in theory, numerical simulation, and experiment, the theoretical distribution rule of prestressing is amended through a statistical method, and a more accurate formula of prestressing is obtained. Through the calculation of the stress and bending moment in the dangerous section of the ring gear through prestressing, the formula for checking the tooth root flexural fatigue strength in the interference fit prestressing is inferred. This research proposes a tooth root bending strength conditional formula for the inner ring gear of the interference fit, which serves as a guide for the design and production of the actual interference joint inner ring gear.展开更多
In the last few decades, prestressed concrete has been rapidly used in bridge engineering due to the enormous development in the construction techniques and the increasing need for long span bridges. High strength con...In the last few decades, prestressed concrete has been rapidly used in bridge engineering due to the enormous development in the construction techniques and the increasing need for long span bridges. High strength concrete has been also more widely spread than the past. It currently becomes more desirable as it has better mechanical properties and durability performance. Major defect of fully prestressed concrete is its low ductility;it may produce less alarming signs than ordinary reinforced concrete via smaller deflection and limited cracking. Therefore, partially prestressing is considered an intermediate design between the two extremes. So, combining high strength concrete with partial prestressing will result in a considerable development in the use of prestressed concrete structures regarding the economical and durability view points. This study presents the results of seven partially prestressed high strength concrete beams in flexure. The tested beams are used to investigate the influence of concrete compressive strength, prestressing steel ratio and flange width on the behavior of partially prestressed beams. The experimentally observed behaviors of all beams were presented in terms of the cracking load, ultimate load, deflection, cracking behavior and failure modes.展开更多
To counter the strength problem of drill string in well of large curvature and small diameter, well axis was taken as datum mis. Based on description of deflection of well an's and on analysis of three dimensional...To counter the strength problem of drill string in well of large curvature and small diameter, well axis was taken as datum mis. Based on description of deflection of well an's and on analysis of three dimensional forces of a small section of drill string, equilibrium differential equations of large deflection drill string were established. The internal forces were found by Longe-Kutta method. The stresses were found by using them and the strength prerequisite was established. Stresses of drill string in lateral horizontal well H767 were computed. The results are in agreement with those of finite element model and soft-rope rigidified model. But the method is simpler for computation than finite element model and is more perfect than soft-rope rigidified model. Curvature of the well is too large and there is stress concentration so that the fraction accident of drill string occurs.展开更多
Precast prestressed Hollow Core Slabs (HCS), are one of the famous and widely used slabs for concrete structures all over the world and widely implemented in the Middle East. HCS are used in industrial, commercial, re...Precast prestressed Hollow Core Slabs (HCS), are one of the famous and widely used slabs for concrete structures all over the world and widely implemented in the Middle East. HCS are used in industrial, commercial, residential buildings, as well as, in the parking structures. This paper succeeded to present new special details for deep HCS to enhance and strengthen the web shear strength capacity of HCS 400 and 500 mm depths respectively at the open parking area. This is subjected to heavy truck wheel loads so as to achieve the LRFD Code’s requirements. However, it is noticed many web shear cracks of HCS are used at parking area at many projects in Gulf Region. On the other hand, ACI318-14 permits no shear reinforcement in prestressed HCS thickness of less than 12.5 in (320 mm). The paper presents experimental tests program, to verify the numerical finite element of deep HCS under maximum design uniform loads, in addition to the new strengthening techniques. New strengthening techniques succeed to enhance the web shear capacity by significant percentage, due to the new details for HCS 400 by 68% up to 256% increasing of the web shear capacity compared to the ordinary HCS section. Also, HCS 500 shear capacity is enhanced with different percentages of strengthening techniques by 55%, up to 197% based on the different cases of strengthening. Furthermore enhancing deep HCS shear performance;the new techniques have an advantage of an easy execution at the site;casting with structural topping, otherwise the preparation can be done in precast factory before site handover, which saves time and cost compared to the others traditional strengthening techniques.展开更多
Liquid polymers(LP)have become an important structural material used in the construction industry in the last decade.This paper investigates the viability of using commercially available LPs as a coating materia...Liquid polymers(LP)have become an important structural material used in the construction industry in the last decade.This paper investigates the viability of using commercially available LPs as a coating material to improve the flexural strength of fiber-modified concrete beams.The scope included preparing rectangular prism concrete beams with a concrete mixture including fly ash and fiber and coating them with four different liquid polymers at a uniform thickness following the curing process while one set of samples was maintained under the same conditions as a control group without coating.In addition,cylindrical samples were prepared to determine the compressive strength of the concrete mixture.Following the curing process in an unconfined open-air laboratory environment for another 28 days,concrete samples were tested to determine the flexural strength and deflection characteristics under center point loading equipment.The results revealed that all four coating types enhanced both the flexural strength and the average maximum deflection of the beams compared to the control group.While the enhancement in the flexural strength changed approximately between 5%and 36%depending on the coating type,the improvements in average maximum deflections varied between 3.7%and 28.4%.展开更多
Creep is an important characteristic of bamboo and wood materials under long-term loading.This paper aims to study the long-term bending beha-viour of prestressed glulam bamboo-wood beam(GBWB).For this,14 pre-stressed...Creep is an important characteristic of bamboo and wood materials under long-term loading.This paper aims to study the long-term bending beha-viour of prestressed glulam bamboo-wood beam(GBWB).For this,14 pre-stressed GBWBs were selected and subjected to a long-term loading test for 60 days.Then,a comparative analysis was performed for the effects of pre-tension values,the number of pre-stressed wires,and long-term load on the stress variation of the steel wire and the long-term deflection of the beam midspan.The test results showed that with the number of prestressed wires increasing,the total stress of the steel wire in the beam midspan and the ratio of the long-term deflec-tion to the total deflection decreases decreased,but when the number of steel wires exceeded 4,the total stress and long-term deflection was less infuenced;with the pre-tension value increasing,the ratio of the total stress of the steel wire in the beam midspan and the ratio of the long-temm deflection to the total deflec-tion also decreased,but when the prestress force was greater than 3.975 kN,the:total stress and long-term deflection were less affected;with the other parameters unchanged,when the value of the long-term load increased,the total stress of the steel wire decreased,and the long-temm deflection of the beam midspan increased,which shall be more significant with the long-term load greater than 30%of the standard ultimate bearing capacity.After the test,the experimental data were fitted,and the creep coefficient was given.Finally,the long-term stiffness calcula-tion fommula of the pre-stressed GBWB based on creep effect was proposed.The research findings have certain theoretical significance and engineering value.展开更多
Prestressed SUS316 fibers/ZrO2 composite was fabricated using tape casting. Causes of cracks were analyzed by classical thermo-elastic theory and finite element method in preparation process. An optimization design wa...Prestressed SUS316 fibers/ZrO2 composite was fabricated using tape casting. Causes of cracks were analyzed by classical thermo-elastic theory and finite element method in preparation process. An optimization design was carried out on SUS316 fibers’ arrangement modes by reducing residual thermal stress. Interface topography and element distribution of composite were observed, and bending strengths were tested. Results show that cracks are generated along the direction vertical to SUS316 fibers by axial thermal stress due to different thermal expansion coefficients between SUS316 fibers and zirconia, and the average cracking space is 2 mm. No macroscopic defect is found in composite with SUS316 fibers of sine distribution, and it has better interfacial binding force since interdiffusion between SUS316 and zirconia. Bending strengths of composite with 0°/0°lamination are anisotropic and that are 385.74 MPa and 500.7 MPa respectively, but that with 0°/90°lamination is isotropic and it is 433.92 MPa. Bending strength of composite is increased obviously compared with that of zirconia because the prestress of surface is compressive stress.展开更多
Normal strength prestressed concrete I-girders are commonly used as the primary superstructure components in highway bridges. However, shear design guidelines for high strength PC girders are not available in the curr...Normal strength prestressed concrete I-girders are commonly used as the primary superstructure components in highway bridges. However, shear design guidelines for high strength PC girders are not available in the current structural codes. Recently, ten 7.62 m (25 feet) long girders made with high strength concrete were designed, cast, and tested at the University of Houston (UH) to study the ultimate shear strength and the shear concrete contribution (Vc) as a function of concrete strength (f'c). A simple semi-empirical set of equations was developed based on the test results to predict the ultimate shear strength of prestressed concrete I-girders. The UH-developed set of equations is a function of concrete strength (√f'c), web area (bwd), shear span to effective depth ratio (a/d), and percentage of transverse steel (Pt). The proposed UH-Method was found to accurately predict the ultimate shear strength of PC girders with concrete strength up to 117 MPa (17000 psi) ensuring satisfactory ductility. The UH-Method was found to be not as overly conservative as the ACI-318 (2011) code provisions, and also not to overestimate the ultimate shear strength of high strength PC girders as the AASHTO LRFD (2010) code provisions. Moreover, the proposed UH-Method was found fairly accurate and not exceedingly conservative in predicting the concrete contribution to shear for concrete strength up to 117 MPa (17000 psi).展开更多
Prestressed steel ultrahigh-strength reinforced concrete(PSURC) beam is a new type of prestressed concrete beam, which not only has a considerable compressive strength attributed to the ultrahigh strength concrete, bu...Prestressed steel ultrahigh-strength reinforced concrete(PSURC) beam is a new type of prestressed concrete beam, which not only has a considerable compressive strength attributed to the ultrahigh strength concrete, but also ensures a certain degree of ductility at failure due to the existence of structural steel. Five of these beams were monotonically tested until shear failure to investigate the static shear performance including the failure pattern, loaddeflection behavior, shear capacity, shear crack width and shear ductility. The experimental results show that these beams have superior shear capacity, crack control ability and shear ductility. To study the shear performance under repeated overloading, seven PSURC beams were loaded in cyclic test simultaneously. The overall shear performance of cycled beams is similar to that of uncycled beams at low load level but different at high load level. The shear capacity and crack control ability of cycled beams at high load level are reduced, whereas the shear ductility is improved. In addition, the influences of variables including the degree of prestress, stirrup ratio and load level on the shear performance of both uncycled and cycled beams were also discussed and compared, respectively.展开更多
Based on a large number of orthogonal tests and theoretical analyses, the retarding mortar which meets the requirements of retard-bonded prestressed concrete was prepared. Initial setting time of the retarding mortar ...Based on a large number of orthogonal tests and theoretical analyses, the retarding mortar which meets the requirements of retard-bonded prestressed concrete was prepared. Initial setting time of the retarding mortar may vary from several hours to 15 d at 5 ℃-35 ℃ due to quantities and average curing temperature. And its 28 d compressive strength is above 35 MPa. Thus the influence of quantities on setting time and 28 d compressive strength, and the relationship between setting time and average curing temperature were investigated. The optimum quantities were obtained by studying the interaction of admixtures, and the retarding mechanism was discussed. Based on 52 retard-bonded prestressed strands by manual work from 24 retard-bonded prestressed concrete T-beams, static friction drag, change factor κ and friction factor μ were obtained from the test when retard-bonded prestressed strands were tensioned. Application of the retarding mortar will be vast in practical concrete projects.展开更多
The structural behavior of prestressed high strength steel(HSS)tubular members is investigated through the execution of advanced finite element modeling.Numerical models are developed and validated against published e...The structural behavior of prestressed high strength steel(HSS)tubular members is investigated through the execution of advanced finite element modeling.Numerical models are developed and validated against published experimental data on HSS tubular members subjected to different levels of initial prestress and loaded either in tension or compression.The effect of the presence or absence of grouting on the strength and ductility of the members is also considered.To numerically replicate the structural response recorded in the tests,some key modeling features including the employed numerical solver,the adopted material models and the element types warrant careful consideration.Upon developing of the finite element models,the numerically generated ultimate loads,the corresponding failure modes and the full load-deformation curves are compared to the experimental ones,indicating a successful validation.As anticipated,prestressing enhances the load-bearing capacity for the tensile members,whereas it is detrimental for the compressive ones.A series of parametric studies is performed to assess the influence of key factors on the structural response of prestressed HSS members and the obtained results are discussed.Design guidance for tensile and compressive prestressed tubular members is also provided.展开更多
Prestressed concrete segmental box girder bridges are composed of short concrete segments that are either precast or cast in situ and then joined together by longitudinally post-tensioning internal,external,or mixed t...Prestressed concrete segmental box girder bridges are composed of short concrete segments that are either precast or cast in situ and then joined together by longitudinally post-tensioning internal,external,or mixed tendons.The objectives of this study are to monitor the construction process of the external prestressing tendons to strengthen the bridge structure and perform a field load test to measure the strain and the deflection of the anchorage devices of the external prestressing tendons to determine the state of these devices after tension forces are applied.The monitoring process of the external prestressing tendons construction includes inspecting the cracks in the diaphragm anchorage and the deviation block devices before the tension forces are applied to the external tendons;measuring the deformation of the steel deviation cross beam during the tension process;measuring the deformation of the box girder after different levels of tension forces are applied;measuring the elongation of the external tendons in each level of the tension;and measuring the natural frequency of the external tendons after the tension process is complete.The results of the monitoring process show that the measured values of the deformation,the elongation,and the natural frequency meet the requirements.Therefore,there is no damage during the construction and the tensioning of the external prestressing tendons.A field load test is performed to the anchorage beam,the steel deviation block devices,and the steel deviation cross beam.The field load test results of the anchorage devices show that the values of the strains,the stresses,and the deflection are less than the respective allowable limit values in the requirements.Therefore,the anchorage devices have sufficient strength,and the working state is good after the tension forces are applied to the external prestressing tendons.展开更多
In order to investigate and research the fatigue cracking of prestressed concrete fatigue properties and loading and stiffness degeneration process,cyclic loading tests were carried out on six prestressed concrete bea...In order to investigate and research the fatigue cracking of prestressed concrete fatigue properties and loading and stiffness degeneration process,cyclic loading tests were carried out on six prestressed concrete beams and the stiffness degradation under fatigue was investigated. A simulation model of stiffness degradation is proposed based on the stiffness analysis of the fatigue-damaged section. The elastic modulus of damaged concrete and the effective residual area of steel were introduced as well as an adjusted three-stage concrete fatigue damage evolution model. The strip method was used to analyze concrete damage due to changing stress along the depth of the beam section. The simulation and test results were compared and a method of predicting fatigue deflection was presented based on the simulation model. The predicted results were compared with that of the neural network method. It is in good agreement for the simulation results with the test results. It is only less than5% error for the simulation model which can reveal the two-stage degradation of prestressed concrete beams under cyclic loading. It is more precise for the simulation prediction method under proper conditions.展开更多
The use of the sand concrete makes it possible to carry out a concrete having physico-mechanical properties answering the structural exigences and having economic and environmental advantages compared to the classical...The use of the sand concrete makes it possible to carry out a concrete having physico-mechanical properties answering the structural exigences and having economic and environmental advantages compared to the classical concrete. The present study aims to connecting the parameters of a formulation based on an empirical formula of Caquot in order to optimize, on the one hand the couple compressive strength/absorption of water under various degrees of hygrometry, and on the other hand more precisely to use the concrete sand in the public works sector in the prefabrication of prestressed beams and hollow bricks. The results show the importance of the type of formulation used because it takes into account the percentages of fillers of sand which is a co-product (waste) of massive rock crushing. In addition, the use of fillerized sands, which are wastes of crushing basaltic rocks and containing a small percentage of fillers, is efficient in the manufacture of prestressed beams. As for the hollow bricks, a fillerized basalt sand, containing a high percentage of filler, as well as a sand dune, gives satisfactory results.展开更多
Attempts are being made to utilize Reinforced Baked Clay (RBC) as a substitute of Reinforced Cement Concrete (RCC) for construction of low cost houses in plains of Pakistan. Since baked clay is considered to be more b...Attempts are being made to utilize Reinforced Baked Clay (RBC) as a substitute of Reinforced Cement Concrete (RCC) for construction of low cost houses in plains of Pakistan. Since baked clay is considered to be more brittle as compared to concrete. Therefore, it is necessary to investigate how deflection and crack width of RBC beams subjected to impact loading are governed by amount of reinforcement. This paper presents the behaviour of RBC beams under drop weight impact loading. The beams were reinforced with two steel bars, one in compression zone and the other in tension zone. In group A beams, the diameter of steel bars was 12.7 mm, while the beams of group B were reinforced with steel bars of 15.8 mm diameter. The RBC beams were subjected to repeated impacts of a hammer of mass 21 kg falling from a height of 1000 mm. The results show that 1) three times reduction in deflection, and 2) 2.5 times decrease in crack width, were achieved in RBC beams by increasing the area of steel to 50%. In addition to this, all the RBC beams failed within nine blows of the hammer, irrespective of area of reinforcement.展开更多
基金supported by the National Natural Science Foundation of China(51978345,52278264).
文摘A theoretical analysis of upward deflection and midspan deflection of prestressed bamboo-steel composite beams is presented in this study.The deflection analysis considers the influences of interface slippage and shear deformation.Furthermore,the calculation model for flexural capacity is proposed considering the two stages of loading.The theoretical results are verified with 8 specimens considering different prestressed load levels,load schemes,and prestress schemes.The results indicate that the proposed theoretical analysis provides a feasible prediction of the deflection and bearing capacity of bamboo-steel composite beams.For deflection analysis,the method considering the slippage and shear deformation provides better accuracy.The theoretical method for bearing capacity matches well with the test results,and the relative errors in the serviceability limit state and ultimate limit state are 4.95%and 5.85%,respectively,which meet the accuracy requirements of the engineered application.
基金Sponsored by the National Natural Science Foundation of China(Grant No.50678050)
文摘In order to validate the accuracy of nonlinear fire simulation programs,comparison analysis is carried out between simulation and experiment induced from small-scale specimens,and then fire resistance of large-scale prestressed concrete slabs is further investigated through parameter expansion.The influences on fire resistance ratings controlled by deflection are explored and discussed,including effective span,concrete cover thickness,load level,prestress degree,effective prestress,composite reinforcement index and other factors.The calculated results indicate that fire resistance ratings of large-scale bonded prestressed concrete simply supported slabs are bigger than those of small-scale ones.Finally,the calculation formulas of fire resistance ratings controlled by deflection are established,which rationally consider the influence of effective span,concrete cover thickness,load level,composite reinforcement index and so on key factors.
文摘The flexural behaviors of continuous fully and partially prestressed steel fiber reinforced high strength concrete beams are studied by experiment and nonlinear finite element analysis. Three levels of partial prestress ratio (PPR) are considered, and three pairs of two-span continuous beams with box sections varying in size are designed. The major parameters involved in the study include the PPR and the fiber location. It is concluded that the prestressed high strength concrete beam exhibits satisfactory ductility; the influences of steel fiber on the crack behaviors for partially prestressed beams are not as obvious as those for fully prestressed ones; steel fibers can improve the structural stiffness after cracking for fully prestressed high strength concrete beams; the moment redistribution from mid-span to intermediate support in the first stage should be mainly considered in practical design.
基金Sponsored by the National Natural Science Foundation of China(Grant No.50878037,51078059,51178078)
文摘This paper presents the results of four partially prestressed ultra-high strength concrete beams in flexure. The test results are used to evaluate the effects of prestressing tendon depth and area on flexure behavior of specimen beams. The test results indicate that: the cracking load,yielding load,peak load and stiffness postcracking of specimen beams are enhanced by reducing prestressing tendon depth or increasing prestressing tendon area, and the flexural ductility is improved by increasing prestressing tendon depth or reducing prestressing tendon area. The effect of complex reinforcement index considering the strength of the equivalence principle and the reinforcement position on loading levels under serviceability limit state,flexural strength and displacement ductility factor are studied. The influence coefficient of prestressing tendon kpis introduced in the complex reinforcement index. As the complex reinforcement index increases, the loading levels under serviceability limit state and flexural strength increases linearly,and the displacement ductility factor decreases linearly. The test results also verify the conventional beam flexural theory based on the plane cross-section assumption for predicting ultimate flexural strength of partially prestressed ultra-high strength concrete beams is valid. After the introduction of the coefficient kp,the calculation method of cracks in code for design of concrete structure in china are appropriated for the specimen beams.
基金Supported by Hunan Provincial Natural Science Foundation of China(Grant No.2018JJ4006)National Independent Innovation Demonstration Area Foundation of Changsha Zhuzhou Xiangtan(Grant No.2018XK2302)
文摘When the gearbox body interference is connected to the ring gear, prestressing occurs in the ring gear, which has a significant impact on the strength and life of the gear. Research on the prestressing of the inner ring gear is in the preliminary stage, and the distribution rule of the prestressing and the influence of each parameter on the interference prestressing have not been derived. In this paper, based on the method of calculating the prestressing of the thick cylinder in interference fit, the ring gear is found to be equivalent to a thick cylinder, and the distribution rule of prestressing of the ring gear in the interference fit is inferred. Then, by modeling and analyzing the gearbox body and ring gear in the interference fit using ABAQUS, the distribution rule of prestressing the ring gear in the interference fit is obtained through a numerical simulation. Finally, the prestressing of the ring gear in the interference fit is measured using X-ray di raction, and the distribution rule of prestressing of the ring gear in the interference fit is obtained through analysis. Compared with the distribution rule of prestressing in theory, numerical simulation, and experiment, the theoretical distribution rule of prestressing is amended through a statistical method, and a more accurate formula of prestressing is obtained. Through the calculation of the stress and bending moment in the dangerous section of the ring gear through prestressing, the formula for checking the tooth root flexural fatigue strength in the interference fit prestressing is inferred. This research proposes a tooth root bending strength conditional formula for the inner ring gear of the interference fit, which serves as a guide for the design and production of the actual interference joint inner ring gear.
文摘In the last few decades, prestressed concrete has been rapidly used in bridge engineering due to the enormous development in the construction techniques and the increasing need for long span bridges. High strength concrete has been also more widely spread than the past. It currently becomes more desirable as it has better mechanical properties and durability performance. Major defect of fully prestressed concrete is its low ductility;it may produce less alarming signs than ordinary reinforced concrete via smaller deflection and limited cracking. Therefore, partially prestressing is considered an intermediate design between the two extremes. So, combining high strength concrete with partial prestressing will result in a considerable development in the use of prestressed concrete structures regarding the economical and durability view points. This study presents the results of seven partially prestressed high strength concrete beams in flexure. The tested beams are used to investigate the influence of concrete compressive strength, prestressing steel ratio and flange width on the behavior of partially prestressed beams. The experimentally observed behaviors of all beams were presented in terms of the cracking load, ultimate load, deflection, cracking behavior and failure modes.
文摘To counter the strength problem of drill string in well of large curvature and small diameter, well axis was taken as datum mis. Based on description of deflection of well an's and on analysis of three dimensional forces of a small section of drill string, equilibrium differential equations of large deflection drill string were established. The internal forces were found by Longe-Kutta method. The stresses were found by using them and the strength prerequisite was established. Stresses of drill string in lateral horizontal well H767 were computed. The results are in agreement with those of finite element model and soft-rope rigidified model. But the method is simpler for computation than finite element model and is more perfect than soft-rope rigidified model. Curvature of the well is too large and there is stress concentration so that the fraction accident of drill string occurs.
文摘Precast prestressed Hollow Core Slabs (HCS), are one of the famous and widely used slabs for concrete structures all over the world and widely implemented in the Middle East. HCS are used in industrial, commercial, residential buildings, as well as, in the parking structures. This paper succeeded to present new special details for deep HCS to enhance and strengthen the web shear strength capacity of HCS 400 and 500 mm depths respectively at the open parking area. This is subjected to heavy truck wheel loads so as to achieve the LRFD Code’s requirements. However, it is noticed many web shear cracks of HCS are used at parking area at many projects in Gulf Region. On the other hand, ACI318-14 permits no shear reinforcement in prestressed HCS thickness of less than 12.5 in (320 mm). The paper presents experimental tests program, to verify the numerical finite element of deep HCS under maximum design uniform loads, in addition to the new strengthening techniques. New strengthening techniques succeed to enhance the web shear capacity by significant percentage, due to the new details for HCS 400 by 68% up to 256% increasing of the web shear capacity compared to the ordinary HCS section. Also, HCS 500 shear capacity is enhanced with different percentages of strengthening techniques by 55%, up to 197% based on the different cases of strengthening. Furthermore enhancing deep HCS shear performance;the new techniques have an advantage of an easy execution at the site;casting with structural topping, otherwise the preparation can be done in precast factory before site handover, which saves time and cost compared to the others traditional strengthening techniques.
文摘Liquid polymers(LP)have become an important structural material used in the construction industry in the last decade.This paper investigates the viability of using commercially available LPs as a coating material to improve the flexural strength of fiber-modified concrete beams.The scope included preparing rectangular prism concrete beams with a concrete mixture including fly ash and fiber and coating them with four different liquid polymers at a uniform thickness following the curing process while one set of samples was maintained under the same conditions as a control group without coating.In addition,cylindrical samples were prepared to determine the compressive strength of the concrete mixture.Following the curing process in an unconfined open-air laboratory environment for another 28 days,concrete samples were tested to determine the flexural strength and deflection characteristics under center point loading equipment.The results revealed that all four coating types enhanced both the flexural strength and the average maximum deflection of the beams compared to the control group.While the enhancement in the flexural strength changed approximately between 5%and 36%depending on the coating type,the improvements in average maximum deflections varied between 3.7%and 28.4%.
基金In the process,this project was supported by the Fundamental Research Funds for the Central Universities(2572017DB02)the natural science foundation of heilongjiang province(LH2019E005)Harbin science and technology innovation talent fund project(2017RAQXJ086).
文摘Creep is an important characteristic of bamboo and wood materials under long-term loading.This paper aims to study the long-term bending beha-viour of prestressed glulam bamboo-wood beam(GBWB).For this,14 pre-stressed GBWBs were selected and subjected to a long-term loading test for 60 days.Then,a comparative analysis was performed for the effects of pre-tension values,the number of pre-stressed wires,and long-term load on the stress variation of the steel wire and the long-term deflection of the beam midspan.The test results showed that with the number of prestressed wires increasing,the total stress of the steel wire in the beam midspan and the ratio of the long-term deflec-tion to the total deflection decreases decreased,but when the number of steel wires exceeded 4,the total stress and long-term deflection was less infuenced;with the pre-tension value increasing,the ratio of the total stress of the steel wire in the beam midspan and the ratio of the long-temm deflection to the total deflec-tion also decreased,but when the prestress force was greater than 3.975 kN,the:total stress and long-term deflection were less affected;with the other parameters unchanged,when the value of the long-term load increased,the total stress of the steel wire decreased,and the long-temm deflection of the beam midspan increased,which shall be more significant with the long-term load greater than 30%of the standard ultimate bearing capacity.After the test,the experimental data were fitted,and the creep coefficient was given.Finally,the long-term stiffness calcula-tion fommula of the pre-stressed GBWB based on creep effect was proposed.The research findings have certain theoretical significance and engineering value.
基金Funded by the Science and Technique Research and Development Program of Shaanxi Province (No. 2007K06-13)the Science and Technique Program of Xi’an City (No. YF07061)
文摘Prestressed SUS316 fibers/ZrO2 composite was fabricated using tape casting. Causes of cracks were analyzed by classical thermo-elastic theory and finite element method in preparation process. An optimization design was carried out on SUS316 fibers’ arrangement modes by reducing residual thermal stress. Interface topography and element distribution of composite were observed, and bending strengths were tested. Results show that cracks are generated along the direction vertical to SUS316 fibers by axial thermal stress due to different thermal expansion coefficients between SUS316 fibers and zirconia, and the average cracking space is 2 mm. No macroscopic defect is found in composite with SUS316 fibers of sine distribution, and it has better interfacial binding force since interdiffusion between SUS316 and zirconia. Bending strengths of composite with 0°/0°lamination are anisotropic and that are 385.74 MPa and 500.7 MPa respectively, but that with 0°/90°lamination is isotropic and it is 433.92 MPa. Bending strength of composite is increased obviously compared with that of zirconia because the prestress of surface is compressive stress.
文摘Normal strength prestressed concrete I-girders are commonly used as the primary superstructure components in highway bridges. However, shear design guidelines for high strength PC girders are not available in the current structural codes. Recently, ten 7.62 m (25 feet) long girders made with high strength concrete were designed, cast, and tested at the University of Houston (UH) to study the ultimate shear strength and the shear concrete contribution (Vc) as a function of concrete strength (f'c). A simple semi-empirical set of equations was developed based on the test results to predict the ultimate shear strength of prestressed concrete I-girders. The UH-developed set of equations is a function of concrete strength (√f'c), web area (bwd), shear span to effective depth ratio (a/d), and percentage of transverse steel (Pt). The proposed UH-Method was found to accurately predict the ultimate shear strength of PC girders with concrete strength up to 117 MPa (17000 psi) ensuring satisfactory ductility. The UH-Method was found to be not as overly conservative as the ACI-318 (2011) code provisions, and also not to overestimate the ultimate shear strength of high strength PC girders as the AASHTO LRFD (2010) code provisions. Moreover, the proposed UH-Method was found fairly accurate and not exceedingly conservative in predicting the concrete contribution to shear for concrete strength up to 117 MPa (17000 psi).
基金Supported by the National Natural Science Foundation of China(No.51078059)
文摘Prestressed steel ultrahigh-strength reinforced concrete(PSURC) beam is a new type of prestressed concrete beam, which not only has a considerable compressive strength attributed to the ultrahigh strength concrete, but also ensures a certain degree of ductility at failure due to the existence of structural steel. Five of these beams were monotonically tested until shear failure to investigate the static shear performance including the failure pattern, loaddeflection behavior, shear capacity, shear crack width and shear ductility. The experimental results show that these beams have superior shear capacity, crack control ability and shear ductility. To study the shear performance under repeated overloading, seven PSURC beams were loaded in cyclic test simultaneously. The overall shear performance of cycled beams is similar to that of uncycled beams at low load level but different at high load level. The shear capacity and crack control ability of cycled beams at high load level are reduced, whereas the shear ductility is improved. In addition, the influences of variables including the degree of prestress, stirrup ratio and load level on the shear performance of both uncycled and cycled beams were also discussed and compared, respectively.
文摘Based on a large number of orthogonal tests and theoretical analyses, the retarding mortar which meets the requirements of retard-bonded prestressed concrete was prepared. Initial setting time of the retarding mortar may vary from several hours to 15 d at 5 ℃-35 ℃ due to quantities and average curing temperature. And its 28 d compressive strength is above 35 MPa. Thus the influence of quantities on setting time and 28 d compressive strength, and the relationship between setting time and average curing temperature were investigated. The optimum quantities were obtained by studying the interaction of admixtures, and the retarding mechanism was discussed. Based on 52 retard-bonded prestressed strands by manual work from 24 retard-bonded prestressed concrete T-beams, static friction drag, change factor κ and friction factor μ were obtained from the test when retard-bonded prestressed strands were tensioned. Application of the retarding mortar will be vast in practical concrete projects.
文摘The structural behavior of prestressed high strength steel(HSS)tubular members is investigated through the execution of advanced finite element modeling.Numerical models are developed and validated against published experimental data on HSS tubular members subjected to different levels of initial prestress and loaded either in tension or compression.The effect of the presence or absence of grouting on the strength and ductility of the members is also considered.To numerically replicate the structural response recorded in the tests,some key modeling features including the employed numerical solver,the adopted material models and the element types warrant careful consideration.Upon developing of the finite element models,the numerically generated ultimate loads,the corresponding failure modes and the full load-deformation curves are compared to the experimental ones,indicating a successful validation.As anticipated,prestressing enhances the load-bearing capacity for the tensile members,whereas it is detrimental for the compressive ones.A series of parametric studies is performed to assess the influence of key factors on the structural response of prestressed HSS members and the obtained results are discussed.Design guidance for tensile and compressive prestressed tubular members is also provided.
文摘Prestressed concrete segmental box girder bridges are composed of short concrete segments that are either precast or cast in situ and then joined together by longitudinally post-tensioning internal,external,or mixed tendons.The objectives of this study are to monitor the construction process of the external prestressing tendons to strengthen the bridge structure and perform a field load test to measure the strain and the deflection of the anchorage devices of the external prestressing tendons to determine the state of these devices after tension forces are applied.The monitoring process of the external prestressing tendons construction includes inspecting the cracks in the diaphragm anchorage and the deviation block devices before the tension forces are applied to the external tendons;measuring the deformation of the steel deviation cross beam during the tension process;measuring the deformation of the box girder after different levels of tension forces are applied;measuring the elongation of the external tendons in each level of the tension;and measuring the natural frequency of the external tendons after the tension process is complete.The results of the monitoring process show that the measured values of the deformation,the elongation,and the natural frequency meet the requirements.Therefore,there is no damage during the construction and the tensioning of the external prestressing tendons.A field load test is performed to the anchorage beam,the steel deviation block devices,and the steel deviation cross beam.The field load test results of the anchorage devices show that the values of the strains,the stresses,and the deflection are less than the respective allowable limit values in the requirements.Therefore,the anchorage devices have sufficient strength,and the working state is good after the tension forces are applied to the external prestressing tendons.
基金Sponsored by the National Natural Science Foundation of China(Grant No.5117804251308159+4 种基金51578047)the National High Technology Research and Development Program Project(Grant No.2008AA11Z102)China Railway Corporation Research and Development of Science and Technology Plan Project(Grant No.2014G004-B)China Communications Construction Co.LTD Science and Technology Research and Development Projects(Grant No.2014-ZJKJ-03)
文摘In order to investigate and research the fatigue cracking of prestressed concrete fatigue properties and loading and stiffness degeneration process,cyclic loading tests were carried out on six prestressed concrete beams and the stiffness degradation under fatigue was investigated. A simulation model of stiffness degradation is proposed based on the stiffness analysis of the fatigue-damaged section. The elastic modulus of damaged concrete and the effective residual area of steel were introduced as well as an adjusted three-stage concrete fatigue damage evolution model. The strip method was used to analyze concrete damage due to changing stress along the depth of the beam section. The simulation and test results were compared and a method of predicting fatigue deflection was presented based on the simulation model. The predicted results were compared with that of the neural network method. It is in good agreement for the simulation results with the test results. It is only less than5% error for the simulation model which can reveal the two-stage degradation of prestressed concrete beams under cyclic loading. It is more precise for the simulation prediction method under proper conditions.
文摘The use of the sand concrete makes it possible to carry out a concrete having physico-mechanical properties answering the structural exigences and having economic and environmental advantages compared to the classical concrete. The present study aims to connecting the parameters of a formulation based on an empirical formula of Caquot in order to optimize, on the one hand the couple compressive strength/absorption of water under various degrees of hygrometry, and on the other hand more precisely to use the concrete sand in the public works sector in the prefabrication of prestressed beams and hollow bricks. The results show the importance of the type of formulation used because it takes into account the percentages of fillers of sand which is a co-product (waste) of massive rock crushing. In addition, the use of fillerized sands, which are wastes of crushing basaltic rocks and containing a small percentage of fillers, is efficient in the manufacture of prestressed beams. As for the hollow bricks, a fillerized basalt sand, containing a high percentage of filler, as well as a sand dune, gives satisfactory results.
文摘Attempts are being made to utilize Reinforced Baked Clay (RBC) as a substitute of Reinforced Cement Concrete (RCC) for construction of low cost houses in plains of Pakistan. Since baked clay is considered to be more brittle as compared to concrete. Therefore, it is necessary to investigate how deflection and crack width of RBC beams subjected to impact loading are governed by amount of reinforcement. This paper presents the behaviour of RBC beams under drop weight impact loading. The beams were reinforced with two steel bars, one in compression zone and the other in tension zone. In group A beams, the diameter of steel bars was 12.7 mm, while the beams of group B were reinforced with steel bars of 15.8 mm diameter. The RBC beams were subjected to repeated impacts of a hammer of mass 21 kg falling from a height of 1000 mm. The results show that 1) three times reduction in deflection, and 2) 2.5 times decrease in crack width, were achieved in RBC beams by increasing the area of steel to 50%. In addition to this, all the RBC beams failed within nine blows of the hammer, irrespective of area of reinforcement.