Analyzing the Effects of Tool Holder Stiffness on Chatter Vibration Reduction in Turning

This paper investigates the effects of tool holder materials on chatter vibration in turning operations.The study uses a complex dynamic turning model with two degrees of freedom for the orthogonal cutting system.Tool holders made from different materials,including Al 5083,Al 6082,Al 7012,and a standard 4140 material,were subjected to chatter vibration to investigate their process damping capabilities.The study found that the standard tool holder 4140 allows for higher stable depths of cut and produces similar process damping values compared to the other tool holders.Finite element analyses(FEA)were performed to verify the experimental results,and the modal and FEA analyses produced very similar results.The study concludes that future research should investigate the effects of tool holders made from high alloy steel alloys on process damping.Overall,this paper provides important insights into the effects of tool hold-er materials on chatter vibration and process damping in turning operations,which can help in the design of more effi-cient and effective cutting systems.

Grey Relational Optimization of Turning Parameters in Dry Machining of Austenitic Stainless Steel Using Zr Based Coated Tools

The present work aims at the microstructural characterization of TiAlZrN/ Al2O3 and TiAlZrN/Si3N4 coatings deposited via lateral rotating cathodes. The coatings were deposited using Lateral Rotating Cathodes (LARC) technology. The deposited coatings were studied for its cross sectional morphology using scanning electron microscopy. Energy Dispersive Spectrometry was also conducted along the cross section to determine the elemental composition. Micro Vickers hardness test was conducted to determine the hardness of the coatings. The scanning electron microscope images showed that TiAlZrN/Al2O3 coatings showed preferred columnar grain orientation with multilayered structure while TiAlZrN/Si3N4 coatings exhibit a dense grain structure. The TiAlZrN/Si3N4 coating shows a hardness of 31.58 GPa while TiAlZrN/Al2O3 coating shows a hardness of 25.40 GPa. Dry turning tests were performed on AISI 304 stainless steel. The TiAlZrN/Si3N4 coatings show reduced flank wear. Both the coatings even under severe cutting conditions impart surface roughness of less than 1.5 μm.

SURFACE ROUGHNESS PREDICTION MODEL FOR ULTRAPRECISION TURNING ALUMINIUM ALLOY WITH A SINGLE CRYSTAL DIAMOND TOOL

A surface roughness model utilizing regression analysis method is developedfor predicting roughness of ultra-precision machined surface with a single crystal diamond tool. Theeffects of the main variables, such as cutting speed, feed, and depth of cut on surface roughnessare also analyzed in diamond turning aluminum alloy. In order to predict the optimum cuttingconditions during process planning. A lot of experimental results show that the model can predictthe surface roughness effectively under a certain cutting conditions.

Experimental Study on Hard Turning Hardened GCr15 Steel with PCBN Tool

This paper discusses experimental results of turnin g experiments on GCr15 bearing steel hardened to 60～64 HRC. The objective was to d etermine the effect of the cutting parameters on cutting force, chip morphology and resultant workpiece surface quality, more specifically surface texture, micr ostructure alterations, changes in microhardness and residual stresses distribut ion. The changing rules of the main cutting force was shown in this paper which feature a increasing tendency with the improvement of the workpiece hardness wit hin the cutting parameter scope. The rule of cutting force changing with the wor kpiece hardness is accord to the traditional metal cutting theory. Stress value decrease with increasing cutting speed and workpiece hardness. The comparison of the machined surface roughness and harden layer depth of machined surface for d ifferent hardness is shown in Fig.1. The machined surface roughness is the worst when the workpiece hardness is around 50HRC. When the workpiece hardness is ove r 50HRC, the surface roughness value shows a descending tendency with the additi on hardness. The machined superficial harden layer depth shows an increasing ten dency with the improvement of the workpiece hardness. When the workpiece hardnes s is 50HRC the machined superficial harden layer depth is tiptop. When the workp iece hardness is over 50HRC the depth changes little with the addition of workpi ece hardness. The remnant stress status of the machined surface is shown in Fig. 2, which is press stress status both in surface and in base for less cutting par ameters under two kinds of cutting condition. But experiment results show that t ensile stress can be produced under uncomfortable cutting conditions. The deform ation created by the chip formation is reduced whereduce with [TPP126A,+35mm77mm,Z,PY#]Depth from surface (μm) ■ v=200m/min,f=0.24mm/r,ap=0.8mm,60HRC ● v=200m/min,f=0.15mm/r,ap=0.5mm,60HRC Fig.1 The subsurface residual stress between the two experimentsHardness (HRC) Fig.2 The surface finish vs. workpiece hardness the workpiece hardness is improved.

Cutting Temperature and Tool Wear of Hard Turning Hardened Bearing Steel

A study was undertaken to investigate the performan ce of PCBN tool in the finish turning GCr15 bearing steel with different hardness between 30～64 HRC. The natural thermocouple was used to measure the cutting tem p erature, tool life and cutting temperature were investigated and compared. The m aterial can be heated by this instrument which using low voltage and high elec trical current, while PCBN can’t be heated by electrifying directly, so the ke ntanium layer coating over the PCBN is heated, so the PCBN is heated and its th ermoelectric property is got by this method. [TPP129,+60mm88mm,Y,PZ#] Fig.1 Effect of cutting depth and workpiec hardness on. the cutting temperatureThe objective was to determine the influence of the workpiece hardness on change s in cutting temperature and tool wear characterize. It can be found from Fig.1 that the cutting temperature show an increasing tendency with the improvement of workpiece hardness within the cutting speed scope when the workpiece hardness i s under HRC50. And on the other hand, it is found that the cutting temperature s how the downtrend with the improvement of workpiece hardness when the workpiece hardness is over HRC50. According to experimental results, the critical hard ness when turning hardened GCr15 bearing steel with PCBN tool is about HRC50. Th e wear causes of PCBN tool have been found out through taking photos on the micr o-shape of PCBN poly-laminate initial surface as well as face and flank of wea r tool and analysis on chemical elements. It is discovered that the PCBN tools a re not suitable for cutting the workpiece at nearly critical hardness, because n ear the critical hardness, PCBN wear at the highest speed. For researching the w ear rule of PCBN tool, the tool wear experiments have been carried on by using b earing steel GCr15 at hardness HRC40 and HRC60 with changing cutting speed. The indexes of tool life equations is gained under two kinds of conditions w hich are bigger than 0.6, so the effects of cutting speed on the PCBN tool are m uch less than that of carbide tool and ceramic tool.

Efect of Micro Abrasive Slurry Jet Polishing on Properties of Coated Cemented Carbide Tools

Owing to the popularization of coating technology, physical Vapor Deposition (PVD) coated tools have become indispensable in the cutting process. Additionally, the post-treatment of coated tools applied to industrial production can efectively enhance the surface quality of coating. To improve the processing performance of coated tools, micro abrasive slurry jet (MASJ) polishing technology is frst applied to the post-treatment of coated tools. Subsequently, the efects of process parameters on the surface quality and cutting thickness of coating are investigated via single-factor experiments. In the experiment, the best surface roughness is obtained by setting the working pressure to 0.4 MPa, particle size to 3 μm, incidence angle to 30°, and abrasive mass concentration to 100 g/L. Based on the results of the single-factor experiments, combination experiments are designed, and three types of coated tools with diferent surface qualities and coating thicknesses are obtained. The MASJ process for the post-treatment of coated tools is investigated based on a tool wear experiment and the efects of cutting parameters on the cutting force and workpiece surface quality of three types of cutting tools. The result indicates that MASJ machining can efectively improve the machining performance of coated tools.

Status of research on non-conventional technology assisted single-point diamond turning

With the increasing use of difficult-to-machine materials in aerospace applications,machining requirements are becoming ever more rigorous.However,traditional single-point diamond turning(SPDT)can cause surface damage and tool wear.Thus,it is difficult for SPDT to meet the processing requirements,and it has significant limitations.Research indicates that supplementing SPDT with unconventional techniques can,importantly,solve problems due to the high cutting forces and poor surface quality for difficult-to-machine materials.This paper first introduces SPDT and reviews research into unconventional techniques for use with SPDT.The machining mechanism is discussed,and the main advantages and disadvantages of various methods are investigated.Second,hybrid SPDT is briefly described,which encompasses ultrasonic-vibration magnetic-field SPDT,ultrasonic-vibration laser SPDT,and ultrasonic-vibration cold-plasma SPDT.Compared with the traditional SPDT method,hybrid SPDT produces a better optical surface quality.The current status of research into unconventional techniques to supplement SPDT is then summarized.Finally,future development trends and the application prospects of unconventional assisted SPDT are discussed.

TOOL FORCE MODEL FOR DIAMOND TURNING

A new tool force model to be presented is based upon process geometry and thecharacteristics of the force system, in which the forces acting on the tool rake face, the cuttingedge rounding and the clearance face have been considered, and the size effect is accountable forthe new model. It is desired that the model can be well applicable to conventional diamond turningand the model may be employed as a tool in the design of diamond tools. This approach is quitedifferent from traditional investigations primarily based on empirical studies. As the depth of cutbecomes the same order as the rounded cutting edge radius, sliding along the clearance face due toelastic recovery of workpiece material and plowing due to the rounded cutting edge may becomeimportant in micro-machining, the forces acting on the cutting edge rounding and the clearance facecan not be neglected. For this reason, it is very important to understand the influence of someparameters on tool forces and develop a model of the relationship between them.

Tool path generation of ultra-precision diamond turning: A state-of-the-art review

With the increasing market demand for optical complex surface parts,the application of multi-axis ultraprecision single-point diamond turning is increasing.A tool path generation method is very important to decrease manufacturing time,enhance surface quality,and reduce cost.Compared with the tool path generation of the traditional multi-axis milling,that of the ultra-precision single-point diamond turning requires higher calculation accuracy and efficiency.This paper reviews the tool path generation of ultra-precision diamond turning,considering several key issues:cutter location(CL)points calculation,the topological form of tool path,interpolation mode,and G code optimization.

A Fast Tool Servo System for Fabrication of Micro-structured Surfaces on A Diamond Turning Machine

A fast tool servo (FTS) system is developed for the fabrication of non-rotationally symmetric micro-structured surfaces using single-point diamond turning machines.The constructed FTS employs a piezoelectric tube actuator (PZT) to actuate the diamond tool and a capacitive probe as the feedback sensor.To compensate the inherent nonlinear hysteresis behavior of the piezoelectric actuator,Proportional Integral (PI) feedback control is implemented.Besides,a feed-forward control based on a simple feed-forward predictor has been added to achieve better tracking performance.Experimental results indicate that error motions in the performance of the system caused by hysteresis can be reduced greatly and the micro-structured surface is successfully fabricated by implementing the FTS.

Tool path generation and optimization for freeform surface diamond turning based on an independently controlled fast tool servo

Diamond turning based on a fast tool servo(FTS)is widely used in freeform optics fabrication due to its high accuracy and machining efficiency.As a new trend,recently developed high-frequency and long-stroke FTS units are independently driven by a separate control system from the machine tool controller.However,the tool path generation strategy for the independently controlled FTS is far from complete.This study aims to establish methods for optimizing tool path for the independent control FTS to reduce form errors in a single step of machining.Different from the conventional integrated FTS control system,where control points are distributed in a spiral pattern,in this study,the tool path for the independent FTS controller is generated by the ring method and the mesh method,respectively.The machined surface profile is predicted by simulation and the parameters for the control point generation are optimized by minimizing the deviation between the predicted and the designed surfaces.To demonstrate the feasibility of the proposed tool path generation strategies,cutting tests of a two-dimensional sinewave and a micro-lens array were conducted and the results were compared.As a result,after tool path optimization,the peak-to-valley form error of the machined surface was reduced from 429 nm to 56 nm for the two-dimensional sinewave by using the ring method,and from 191 nm to 103 nm for the micro-lens array by using the mesh method,respectively.

Experimentation on Tool Wear and Surface Roughness in AISI D2 Steel Turning with WC Insert

The Taguchi method, based on an orthogonal arrangement (L9, 33), the vari-ance analysis, the signal-to-noise ratios and the response surface methodol-ogy have been used to optimize maximum flank wear (VBmax) and surface roughness (Ra) of the cutting tool when turning a hardened steel AISI D2 (65 HRC) with PVD—TiAlN coated WC insert upon dry environment. By em-ploying regression models;cutting speed, cutting depth and feed rate, which optimize maximum flank wear and surface roughness were validated. Results of relation signal-to-noise ratios, showed that with cutting speed of 200 m/min, cutting depth of 0.2 mm and feed rate of 0.20 mm/rev, Ra is opti-mized. With cutting speed of 150 m/min, cutting depth of 0.4 mm and feed rate of 0.3 mm/rev, VBmax is optimized. Through the variance analysis it was concluded that the depth of cut was the main parameter that affected on the surface roughness;whereas, the feed rate was the most influential parameter on the flank wear. Confirmation test results showed that the Taguchi method was very successful in the optimization of machining parameters for mini-mum surface roughness and flank wear in the turning of the D2 steel.

Research on the Seebeck effect in efficient turning process and improving tool life

In this paper, for the tool wear problem of the cutting process, the study on improving tool life has been done through the analysis of the Seebeck effect in the efficient turning process. The generation principle of the self-excited electric current in the cutting process is studied, and also its effect on the life of the turning cutter is studied, so as to reveal the mechanism of the self-excited electric current accelerating the wear of cutting tools. The study results show that the self-excited electric current which is generated during the cutting process is one of the main reasons that cause both the accelerated hardening and the low life of cutting tools to happen. Thus, if the generation of self-excited current is avoided and reduced, the cutting performance of cutting tools can be effectively improved, so to improve the tool life. The study can provide the anti-friction and anti-wear theory basis for the design of the efficient cutting tools.

Influence of Cutting Speed, Feed Rate and Bulk Texture on the Surface Finish of Nitrogen Alloyed Duplex Stainless Steels during Dry Turning

This paper presents the results of experimental work carried out in dry turning of cast duplex stainless steels (ASTM A 995 Grade4A and ASTM A 995 Grade5A) using TiC and TiCN coated cemented carbide cutting tools. The turning tests were conducted at five different cutting speeds (80, 100, 120, 140 and 160 m/min) and three different feed rates (0.04, 0.08 and 0.12 mm/rev) with a constant depth of cut (0.5 mm). The influence of cutting speed and feed rate on the machined surface roughness was investigated. Texture analysis (Bulk) was also carried out to study the impact of preferred orientation on the resulting surface roughness. The result reveals that the increasing cutting speed decreases the surface roughness till a particular point and then increases whereas;the surface roughness value decreases with the decreasing feed rate. Presence of alpha fiber (Bulk texture analysis) in the austenite phase of 4A work piece material leads to better surface finish. Among both the grades, surface finish of grade 4A is better than grade 5A work piece material.

High-Speed Machining of Malleable Cast Iron by Various Cutting Tools Coated by Physical Vapor Deposition

The coating material of a tool directly affects the efficiency and cost of machining malleable cast iron.However,the machining adaptability of various coating materials to malleable cast iron has been insufficiently researched.In this paper,turning tests were conducted on cemented carbide tools with different coatings(a thick TiN/TiAlN coating,a thin TiN/TiAlN coating,and a nanocomposite(nc)TiAlSiN coating).All coatings were applied by physical vapor deposition.In a comparative study of chip morphology,cutting force,cutting temperature,specific cutting energy,tool wear,and surface roughness,this study analyzed the cutting characteristics of the tools coated with various materials,and established the relationship between the cutting parameters and machining objectives.The results showed that in malleable cast iron machining,the coating material significantly affects the cutting performance of the tool.Among the three tools,the nc-TiAlSiN-coated carbide tool achieved the minimum cutting force,the lowest cutting temperature,least tool wear,longest tool life,and best surface quality.Moreover,in comparisons between cemented-carbide and compacted-graphite cast iron machined under the same conditions,the wear mechanism of the coated tools was found to depend on the cast iron being machined.Therefore,the performance requirements of a tool depend on multiple factors,and selecting an appropriately coated tool for a particular cast iron material is essential.

Test and Evaluation of Stiffness of a Pin Turning Device for Large Marine Engine Crankshafts

In order to prevent unwanted excited vibrations and to secure better machining precision in large size heavy duty machine tools dynamic stiffness is one of the most desirable and critical properties. In the past decades, many researches on machine tool stiffness test and evaluation methodology have been made. However any methodology for a Pin Turning Device (PTD), which is a special kind of turning lathe for machining big size crankshaft pins, is rarely found among them. This study proposes a test and evaluation process of stiffness of a PTD by measuring frequency response function at the tool center point (TCP). For conformance proving for the proposed methodology, stiffness of a PTD obtained by the proposed method with impact hammer test (IHT) has been compared with that determined by FEM.

White Layer of Hard Turned Surface by Sharp CBN Tool

White layers in hard turned surfaces were identified and measured as a function of turning parameters based on the Taguchi method. It reveals that white layers generate on the machine surface in the absence of tool flank wear, and white layer depth varies with the different combinations of hard turning parameters. Turning speed has the most important impact on white layer depth, feed rate follows, and cutting depth at last. The white layer generation consequently suggests a strong couple relation to the heat generation and thermal process of hard turning operation. White layer disappears under an optimal combination of turning parameters by Taguchi method. It suggests that a superior surface integrity without white layer is feasible under some selected combinations of turning parameters by a sharp CBN cutting tool.

平行闸板阀阀座孔加工专用车削刀具设计及实验研究

平行闸板阀被广泛应用在石油钻采配套装备中。采用普通内孔车削刀具加工平行闸板阀阀座孔,需要调头加工,难以使用切削液,并且由于刀杆刚度和硬度较小引起“颤抖”现象,加工工件时不易保证阀座孔的加工质量和形位公差。基于此设计了一套专用车削刀具,增大刀杆的刚度和硬度,方便使用切削液,而且仅需一次装夹,避免掉头加工,以满足阀座孔的形位公差和加工质量要求。采用有限元法对所设计刀具进行了强度校核。通过实验验证,所设计的刀具可以提高加工效率,满足加工质量和形位公差精度要求。

基于改进引力搜索算法的数控车削参数优化方法

为提高数控车削效率,优化生产质量,减少刀具磨损控制生产成本,提出一种基于改进引力搜索算法的数控车削参数优化方法。建立车削参数优化模型,通过多目标约束条件,确定参数优化的取值范围。通过多目标引力搜索方法,确定中心质点位置和质量,衡量质点优劣程度,经过迭代收敛在空间中搜索最优解。利用质点适应度函数并引入混沌思想改进算法实现全局优化。在混沌映射下反复推演质点的最佳位置,获得最终的优化参数最优值。实验结果表明:所提方法能很好地完成参数优化,降低生产成本,具备良好的有效性和鲁棒性。

超精密慢刀伺服车削零件的面型分析与刀具设计方法研究

研究首先分析总结了当前自由曲面复杂零件超精密慢刀伺服车削加工中的具体加工技术挑战,进而系统地研究了自由曲面零件面型特性,零件面型关键参数提取,零件面型参数与刀具参数之间的关联关系。进一步研究了超精密慢刀伺服车削金刚石刀具的几何参数确定方法;并针对自由曲面零件的可加工性,提出了超精密慢刀伺服车削加工中金刚石刀具选用准则。另外,通过超精密慢刀伺服车削加工实际案例和应用加工试验,证明零件面型分析及金刚石刀具几何参数的合理选用,对实现高效稳定的工业化超精密慢刀伺服车削加工至关重要。