Purification of Produced Water from a Sour Oilfield in South Kuwait. 1. Oil-Water Separation and Industrial Salt Production

Produced water from an oil extraction site in South Kuwait was sampled after primary oil – water separation had been carried out. The produced water was filtered through a mixture of activated charcoal and esterified cellulosic material gained from spent coffee grounds as a tertiary adsorption treatment. The earth-alkaline metal ions and heavy metals were separated from the de-oiled produced water by addition of either sodium or potassium hydroxide in the presence of carbon dioxide or by direct addition of solid sodium carbonate. The resulting filtrate gave salt of industrial purity upon selective crystallization on evaporation.

Purification of Produced Water from a Sour Oilfield in South Kuwait. 2. Oil-Water Separation and Crystallization of Calcium Carbonate

Oil-water separation for produced water (PW) originating from an oil extraction site in South Kuwait was carried out using bleached, esterified cellulosic material from used coffee grounds. Thereafter, earth-alkaline metal ions, specifically calcium ions, of the de-oiled PW were removed by precipitation with sodium carbonate to give access to pure sodium chloride as industrial salt from the remaining PW. While the purity of the precipitated calcium carbonate (CaCO3) depends on the precipitation conditions, CaCO3 of up to 95.48% purity can be obtained, which makes it a salable product. The precipitation of CaCO3 decreases the amount of calcium ions in PW from 11,300 ppm to 84 ppm.

Variability in Quantity and Salinity of Produced Water from an Oil Production in South Kuwait

Produced water (PW) is the largest waste stream in the oil and gas industry. Water remains trapped for millions of years in the reservoir with oil and gas. When a hydrocarbon reservoir is infiltrated by a production well, the produced fluids commonly contain water. The understanding of this water’s constituents and volumes is vital for the sustainable continuity of production operations, as PW has a number of negative impacts on the infrastructure integrity of the operation. On the other hand, PW can be an alternative source of irrigation water as well as of industrial salt. Interestingly, both the quantity as well as the quality of PW do not remain constant but can vary, both progressively and erratically, even over short periods of time. This paper discusses such a situation of variable PW in an oil and gas operation in the State of Kuwait.

Economic Evaluation on "Planting Three to Produce Four" High-yielding Project of Super Hybrid-rice in Hunan

The research conducted investigation and survey on 186 farm households in 2014 and carried out economic evaluation on ＂planting three to produce four＂ highyielding project of super hybrid rice. The results showed that the project of ＂planting three to produce four＂ performed significantly in terms of increasing yields and incomes. For example, per unit area yield of one-season late hybrid rice and middleseason hybrid rice proved the highest, and net income from middle-season rice in Longhui was the highest. It is obvious that to increase per unit yield is key for improving net incomes and to reduce machine fees and worker fees is crucial for decreasing fees.

Kinetic Performance of Oil-field Produced Water Treatment by Biological Aerated Filter

The biological aerated filter （BAF） was used to treat the oil-field produced water. The removal efficiency for oil, COD, BOD and suspended solids （SS） was 76.3%-80.3%, 31.6%-57.9%, 8.6.3%-96.3% and76.4%--82.7%, respectively when the hydraulic loading rates varied from 016m·h^-1 to 1.4m·h^-1. The greatest partof removal, for example more than 80% of COD removal, occurred on the top 100cm of the media in BAF. The kinetic .performance of BAF indicated that the relationship of BOD removal efficiency with the hydraulic loadingrates, in biological aerated filters could be described by c1/c1=l-exp（-2.44/L^0.59）. This equation could be used topredict the B OD.removal efficiency at different hydraulic loading rates.

Bioflocculant Produced by Klebsiella sp. MYC and Its Appli-cation in the Treatment of Oil-field Produced Water

Seventy-nine strains of bioflocculant-producing bacteria were isolated from 3 activated sludge samples. Among them, strain MYC was found to have the highest and stable flocculating rate for both kaolin clay suspension and oil-field produced water. The bacterial strain was identified as Klebsiella sp. MYC according to its morphological and biochemical characteristics and 16SrDNA sequence. The optimal medium for bioflocculant production by this bacterial strain was composed of cane sugar 20 g L^-1, KH2PO4 2 g L^-1, K2HPO4 5 g L^- 1, （ NH4）2SO4 0.2 g L^-1, urea 0.5 g L^- 1 and yeast extract 0.5 g L^- 1, the initial pH being 5.5. When the suspension of kaolin clay was treated with0.5% of Klebsiella sp. MYC culture broth, the flocculating rate reached more than 90.0% in the presence of 500mg L^-1 CaCI2, while the flocculating rate for oil-field produced water was near 80.0% in a pH range of 7.0 - 9.0 with the separation of oil and suspended particles from the oil-field produced water under similar conditions. The environment-friendly nature of the bioflocculant and high flocculating rate of the strain make the bioflocculant produced by Klebsiella sp. MYC an attractive bioflocculant in oil-field produced water treatment.

POLY (β-HYDROXYALKANOATES): NATURAL BIOCOMPATIBLE AND BIODEGRADABLE POLYESTERS PRODUCED BY BACTERIA

A wide variety of different types of microorganisms are known to produce intracellular energy and carbon storage products, which have been generally described as being poly (β-hydroxybutyrate), PHB, but which are, more often than not, copolymers containing different alkyl groups at the β-position. Hence, PHB belongs to the family ofpoly (β-hydroxyalkanoastes), PHA, all of which are usually formed as intracellular inclusions in bacteria under unbalanced growth conditions. Recently, it became of industrial interest to evaluate these PHA polyesters as natural biodegradable and biocompatible plastics for a wide range of possible applications, such as surgical sutures or packaging containers. For industrial applications, the controlled incorporation of repeating units with different chain lengths into a series of copolymers is desirable in order to produce polyesters with a range of material properties because physical and chemical characteristics depend strongly on the polymer composition. Such 'tailor-made' copolymers can be produced under controlled growth conditions in that, if a defined mixture of substrates for a certain type of microorganisms is supplied, a well defined and reproducible copolymer is formed.

Fermented Corn Flour Poisoning in Rural Areas of China Ⅲ. Isolation and Identification of Main Toxin Produced by Causal Microorganisms

Flavotoxin A was isolated from Pseudomonas cocovenenans subsp. farinofermentans culture in semisolid potato-dextrose-agar medium, which was isolated from fermented corn meal that had caused food poisoning outbreaks in China. The isolation, purification, and chemical structure of this toxin were studied. The NMR spectra, the uv spectra, and molar extinction coefficients, and the mass spectra of Flavotoxin A are in good agreement with those reported for bongkrekic acid. Therefore, Flavotoxin A and bongkrekic acid are the same organic chemical compound; the molecular formula is C_(28)H_(38)O_7. The oral LD_(50) of the purified Flavotoxin A in mice was 3.16mg/kg (1.53-6.15mg/kg). The existence of bongkrekic acid in toxic fermented corn samples collected during food poisoning outbreaks was also confirmed. It is concluded that bongkrekic acid has played an important role in the outbreaks of fermented corn poisoning. 1989 Academic Press, Inc.

Texture Characteristics of Thin Grain Oriented Silicon Steel Sheet Produced by Cross Shear Rolling

Commercial grain oriented silicon steel was cold rolled to thickness from 0.06 to 0.10 mm by cross shear rolling, then annealed in vacuum or a hydrogen atmosphere furnace. Deformation textures of the sheets were researched by ODF method and reverse pole figure quantitative analyses. The results indicate that: in the condition of the cross shear rolling, the deformation texture of rolled sheet is generally similar to that of conventional rolled sheet, however, the texture distribution through the thickness is asymmetrical. With mismatch speed ratio increasing, the amount of Goss texture increases. With reduction ratio increasing, the intensity of γ-fiber becomes strong.

Performance evaluation of a diesel engine by using producer gas from some under-utilized biomass on dual-fuel mode of diesel cum producer gas

Producer gas through gasification of biomass can be used as an alternate fuel in rural areas due to high potential of biomass resources in India.Experiments were conducted to study the performance of a diesel engine(four stroke,single cylinder,5.25 kW) with respect to its thermal efficiency,specific fuel consumption and diesel substitution by use of diesel alone and producer gas-cum-diesel(dual fuel mode).Three types of biomass,i.e.wood chips,pigeon pea stalks and corn cobs were used for generation of producer gas.A producer gas system consisting of a downdraft gasifier,a cooling cum cleaning unit,a filtering unit and a gas air mixing device was designed,fabricated and used to power a 5.25 kW diesel engine on dual fuel mode.Performance of the engine was reported by keeping biomass moisture contents as 8%,12%,16%,and 21%,engine speed as 1 600 r/min and with variable engine loads.The average value of thermal efficiency on dual fuel mode was found slightly lower than that of diesel mode.The specific diesel consumption was found to be 60%-64% less in dual fuel mode than that in diesel mode for the same amount of energy output.The average diesel substitution of 74% was observed with wood chips followed by corn cobs(78%) and pigeon pea stalks(82%).Based on the performance studied,the producer gas may be used as a substitute or as supplementary fuel for diesel conservation,particularly for stationary engines in agricultural operations in the farm.

The Isolation, Purification and Identification of Fumitremorgin B Produced by Aspergillus fumigatus

Twenty-six strains of Aspergillus fumigaius were screened for toxigenicity for fumitremorgins A and B. Twenty-three of 26 strains can produce fumitremorgin B in rice medium determined by TLC and HPLC, and no fumitremorgin A was detected. The strains of no.C4104 and no. 3656 were inoculated onto 5 kg of rice media and incubated in a modified procedure. Finally, 4.0 g of fumitremorgin B was obtained after extraction and purification by modified methods, and was confirmed by TLC, HPLC, spectral analysis together with other physicochemical analysis. This is the first report of the preparation of fumitremorgin B in China.

Chemical composition of walnuts from three regions in China

To reveal the characteristic chemicals of walnuts from different origins, we analyzed fatty acid composition,tocopherols, phytosterols and total phenolic content (TPC) of walnuts from three main producing regions inChina. The results showed that walnuts were rich in polyunsaturated fatty acids, and the ratio of ω-6 to ω-3 fattyacids was close to the recommendation of Chinese Nutrition Society. Moreover, walnuts contain high contents oftocopherols (331.20–414.71 mg/kg), phytosterols (97.17–110.35 mg/100 g) and phenols (38.51–48.08 mg GAE/kg). Significant chemical differences exist among walnuts from three production regions. The highest content ofpolyunsaturated fatty acids was found in walnuts from the northern China, the highest content of tocopherols inwalnuts from southwest China, and the highest contents of phytosterol and TPC in walnuts from northwest China.However, there was no significant difference in the tocopherol, phytosterol and TPC content of walnuts betweenthe Northern China and Northwest China. The above results provide important references for manufacturers andconsumers to select suitable walnut scientifically and reasonably.

Factors influencing HPAM solution viscosity prepared by produced water using orthogonal method

The effect of temperature and metal ion components on the viscosity of HPAM solution was studied by means of orthogonal method.Five factors and 4 levels were considered for the orthogonal design.The five factors included temperature,contents of Na+,Mg2+,Ca2+ and S2-,and the four levels mainly considered the level of produced water components in main oilfields in China.The experiment results show that temperature is the most important factor to control HPAM solution viscosity prepared by produced water.The effect of ions was in order of Na+>S2->Mg2+>Ca2+.The mechanism of each factor influencing viscosity was also discussed.Based on the actual condition of Nanyang oilfield,the desulfurization was used to improve the solution viscosity,and satisfactory result was obtained.

Experimental Studies of Microwave Reflection and Attenuation by Plasmas Produced by Burning Chemicals in Atmosphere

A series of chemicals are designed and prepared. With the method of thermodynamics, the average electron densities of the plasmas generated by burning chemicals are calculated. The reflection and attenuation of the microwaves, in a frequency band of 2 GHz to 15 GHz, by the plasma are measured. The results of measurements indicate that the plasma can absorb the energies of the microwaves in a broad band and reflect them faintly. Moreover, theoretical discussion reveals that the electron-neutral collision is the major factor that results in the absorption in the wide band. By using Appleton equations, average collision frequencies and electron densities are calculated from the attenuations of microwaves.

Dilemma Produced by Infinity of a Random Walk

We report a dilemma produced by the infinity of a random walk moving along a two-dimensional space sidestep. For this random walk, our investigation shows that using a different model can lead to a different diffusion coefficient of the random walk, which is produced by the infinity of the random walk. The result obtained by us in the present work can serve as a warning to us when we build the models to investigate the corresponding scientific problems.

AN INVESTIGATION ON THE INTERACTION MECHANISM OF β-CAROTENE WITH HALOGEN ATOM PRODUCED IN HALOBENZENE BY UV IRRADIATION

ESR measurements using spin trapping technique were carried out for β-carotene-halobenzene system under UV light irradiation.The ESR spectra observed in the presence and in the absence of β-carotene are markedly different.The possible scheme of β-carotene interacting with halogen atom was proposed.

Mass Spectrometric Study of Clusters Produced by Laser Vaporization of Some Phosphates

The clusters generated by direct laser vaporization of KH2PO4 and Cu-3(PO4)(2) samples are studied by a TOF mass spectrometer. It is found that mainly the [K(KPO3)(n)]* cluster series is generated from KH2PO4 sample and it demonstrates obvious magic numbers, which are n=3, 6, 9, 12, 15. Direct laser vaporization of Cu-3(PO4)(2) sample produced [Cu(CuPO3)n]* cluster series as well as other series with the same building block of (CUPO3).

High-Yield High-Efficiency Positron Generation in High-Z Metal Targets Irradiated by Laser Produced Electrons from Near-Critical Density Plasmas

An improved indirect scheme for laser positron generation is proposed. The positron yields in high-ZZ metal targets irradiated by laser produced electrons from near-critical density plasmas and underdense plasma are investigated numerically. It is found that the positron yield is mainly affected by the number of electrons of energies up to several hundreds of MeV. Using near-critical density targets for electron acceleration, the number of high energy electrons can be increased dramatically. Through start-to-end simulations, it is shown that up to 6.78×10106.78×1010 positrons can be generated with state-of-the-art Joule-class femtosecond laser systems.

Evaporation of Intermediate－mass Fragments from Hot－nuclei Produced by 25MeV／u ^（40）Ar Bombarding ^（159）Tb Target

Ｅｖａｐｏｒａｔｉｏｎ ｏｆ Ｉｎｔｅｒｍｅｄｉａｔｅ－ｍａｓｓ Ｆｒａｇｍｅｎｔｓ ｆｒｏｍ Ｈｏｔ－ｎｕｃｌｅｉ Ｐｒｏｄｕｃｅｄ ｂｙ ２５ＭｅＶ／ｕ^（４０）Ａｒ Ｂｏｍｂａｒｄｉｎｇ^（１５９）Ｔｂ Ｔａｒｇｅｔ￥ＪｉａｎｇＤｏｎｇｘｉｎｇ；...