Accurate Evaluation of Free-form Surface Profile Error Based on Quasi Particle Swarm Optimization Algorithm and Surface Subdivision

Although significant progress has been made in precision machining of free-form surfaces recently, inspection of such surfaces remains a difficult problem. In order to solve the problem that no specific standards for the verification of free-form surface profile are available, the profile parameters of free-form surface are proposed by referring to ISO standards regarding form tolerances and considering its complexity and non-rotational symmetry. Non-uniform rational basis spline（NURBS） for describing free-form surface is formulated. Crucial issues in surface inspection and profile error verification are localization between the design coordinate system（DCS） and measurement coordinate system（MCS） for searching the closest points on the design model corresponding to measured points. A quasi particle swarm optimization（QPSO） is proposed to search the transformation parameters to implement localization between DCS and MCS. Surface subdivide method which does the searching in a recursively reduced range of the parameters u and v of the NURBS design model is developed to find the closest points. In order to verify the effectiveness of the proposed methods, the design model is generated by NURBS and the measurement data of simulation example are generated by transforming the design model to arbitrary position and orientation, and the parts are machined based on the design model and are measured on CMM. The profile errors of simulation example and actual parts are calculated by the proposed method. The results verify that the evaluation precision of freeform surface profile error by the proposed method is higher 10%-22% than that by CMM software. The proposed method deals with the hard problem that it has a lower precision in profile error evaluation of free-form surface.

Least Squares Evaluations for Form and Profile Errors of Ellipse Using Coordinate Data

To improve the measurement and evaluation of form error of an elliptic section, an evaluation method based on least squares fitting is investigated to analyze the form and profile errors of an ellipse using coordinate data. Two error indicators for defining ellipticity are discussed, namely the form error and the profile error, and the difference between both is considered as the main parameter for evaluating machining quality of surface and profile. Because the form error and the profile error rely on different evaluation benchmarks, the major axis and the foci rather than the centre of an ellipse are used as the evaluation benchmarks and can accurately evaluate a tolerance range with the separated form error and profile error of workpiece. Additionally, an evaluation program based on the LS model is developed to extract the form error and the profile error of the elliptic section, which is well suited for separating the two errors by a standard program. Finally, the evaluation method about the form and profile errors of the ellipse is applied to the measurement of skirt line of the piston, and results indicate the effectiveness of the evaluation. This approach provides the new evaluation indicators for the measurement of form and profile errors of ellipse, which is found to have better accuracy and can thus be used to solve the difficult of the measurement and evaluation of the piston in industrial production.

Anovelprofile error model to calculate contact error

A new profile model based on multi-scale asperities is developed and contact error is cal- culated. After stratified sampling, the model can get the distribution law of entity points on each cross section. Asperity radius of curvature is estimated by the relationship between circle radius and the section interval. Contact error is related to surface form error. A model equation of contact error plane is calculated through a method based on static equilibrium theory. Three contact asperities which determine the contact error plane on the rough surface are studied. The simulation results show that contact error can be accurately calculated according to the profile error model.

A Calculation Method of Profile Error Influenced by Tool Error for Two-Axis Coordinated CNC Machining of a Spatial Barrel-Cam

Taking the CNC machining for the spatial barrel-cam with rectilinear translating and a conical roller follower as an example, the calculation method and the law of the profile error influenced by the tool error is given.

Modification Design Method for an Enveloping Hourglass Worm Gear with Consideration of Machining and Misalignment Errors

The influences of machining and misalignment errors play a very critical role in the performance of the anti-backlash double-roller enveloping hourglass worm gear(ADEHWG).However,a corresponding efficient method for eliminating or reducing these errors on the tooth profile of the ADEHWG is seldom reported.The gear engagement equation and tooth profile equation for considering six different errors that could arise from the machining and gear misalignment are derived from the theories of differential geometry and gear meshing.Also,the tooth contact analysis(TCA) is used to systematically investigate the influence of the machining and misalignment errors on the contact curves and the tooth profile by means of numerical analysis and three-dimensional solid modeling.The research results show that vertical angular misalignment of the worm wheel(Δβ) has the strongest influences while the tooth angle error(Δα) has the weakest influences on the contact curves and the tooth profile.A novel efficient approach is proposed and used to minimize the effect of the errors in manufacturing by changing the radius of the grinding wheel and the approaching point of contact.The results from the TCA and the experiment demonstrate that this tooth profile design modification method can indeed reduce the machining and misalignment errors.This modification design method is helpful in understanding the manufacturing technology of the ADEHWG.

Nonparametric Control Scheme for Monitoring Phase Ⅱ Nonlinear Profiles with Varied Argument Values

Profile monitoring is used to check the stability of the quality of a product over time when the product quality is best represented by a function at each time point.However,most previous monitoring approaches have not considered that the argument values may vary from profile to profile,which is common in practice.A novel nonparametric control scheme based on profile error is proposed for monitoring nonlinear profiles with varied argument values.The proposed scheme uses the metrics of profile error as the statistics to construct the control charts.More details about the design of this nonparametric scheme are also discussed.The monitoring performance of the combined control scheme is compared with that of alternative nonparametric methods via simulation.Simulation studies show that the combined scheme is effective in detecting parameter error and is sensitive to small shifts in the process.In addition,due to the properties of the charting statistics,the out-of-control signal can provide diagnostic information for the users.Finally,the implementation steps of the proposed monitoring scheme are given and applied for monitoring the blade manufacturing process.With the application in blade manufacturing of aircraft engines,the proposed nonparametric control scheme is effective,interpretable,and easy to apply.

A NEW ALGORITHM FOR ELIMINATING PHASE-SHIFT ERROR IN PHASE SHIFTING INTERFEROMETRY

The effect of phaseshift error in phase shifting interferometry is investigated. A new algorithm with two sets of 4 samples for eliminating phase shift error is presented. The computer simulation and experiment result show that the phase shift offset should be π when the algorithm is used, and this algorithm has gotten better result than the original 4 sample algorithm.

Investigating Averaging Effect by Using Three Dimension Spectrum

The eddy current displacement sensor＇s averaging effect has been investigated in this paper, and the frequency spectrum property of the averaging effect was also deduced. It indicates that the averaging effect has no influences on measuring a rotor＇s rotating error, but it has visible influences on measuring the rotor＇s profile error. According to the frequency spectrum of the averaging effect, the actual sampling data can be adjusted reasonably, thus measuring precision is improved.

Modeling and experiment of grinding wheel axial profiles based on gear hobs

Hobbing is one of the crucial gear manufacturing processes with high precision and high efficiency.In order to improve the accuracy of hobbing and hob relief grinding,more precise grinding wheels are demanded for relief grinding in the production of gear hobs.In this paper,a new and accurate mathematical method for calculating the axial profile of grinding wheel based on the corresponding gear hob to be ground is proposed.Considering that most researches have been conducted to focus on the optimization of hob geometric feature and only can be applied to a specific type of hand of helix and rake angle of gear hobs.The method in this paper can be served as a general algorithm for generating axial profile of grinding wheels on the basis of the spatial envelope theory,the principle of coordinate system transformation,and studies on normal profile of single-tooth.The accuracy of grinding hobs is based on applying the approach in practical manufacturing.Taking two typical different kinds of pre-grinding gear hobs as examples for calculation and experiment,the results of tooth profile errors strengthen the position that the validity and feasibility of this method,it can be employed for gear hob design and grinding processing.