期刊文献+
共找到105,065篇文章
< 1 2 250 >
每页显示 20 50 100
3DP工艺中阶梯误差与渗透误差相互作用研究
1
作者 杨伟东 马千朝 +2 位作者 刘志越 王媛媛 朱东彬 《天津大学学报(自然科学与工程技术版)》 EI CSCD 北大核心 2024年第3期276-282,共7页
3DP工艺中影响零件成型精度的原理性误差主要来源于阶梯误差和黏结剂渗透误差,并且在误差测量结果中难以区分.本文基于黏结剂在砂床中的流动状态,建立了黏结剂从喷射到渗透过程的数值仿真模型,分析了在二维平面不同角度三角面片打印时... 3DP工艺中影响零件成型精度的原理性误差主要来源于阶梯误差和黏结剂渗透误差,并且在误差测量结果中难以区分.本文基于黏结剂在砂床中的流动状态,建立了黏结剂从喷射到渗透过程的数值仿真模型,分析了在二维平面不同角度三角面片打印时理想模型边界和实际黏结砂粒边界之间的位置误差,研究了阶梯误差和渗透误差之间的相互作用.在此基础上,针对不同角度三角面片打印过程中阶梯误差与黏结剂渗透误差相互作用关系也不相同的问题,提出了基于三角面片法向量方向与成型方向夹角的三角面片偏移误差公式用于表达这两种误差对成型质量的综合影响.结果表明:在向上三角面片中,渗透误差与阶梯误差相互补偿,三角面片偏移误差随着斜面与水平面夹角角度的减小而减小;在向下三角面片中,阶梯误差与渗透误差相互叠加,三角面片偏移误差随着斜面与水平面夹角角度的减小而增大.将三角面片偏移误差的公式计算值与其实际测量值进行对比,公式计算误差最大为0.060 mm,最小为0.002 mm,表明三角面片偏移误差公式用于表达阶梯误差与黏结剂渗透误差综合作用的有效性. 展开更多
关键词 3dp工艺 阶梯误差 渗透误差 成型精度
下载PDF
基于功率谱流形的信息几何DP-TBD算法
2
作者 吴昊 程永强 +2 位作者 杨政 黎湘 王宏强 《电子学报》 EI CAS CSCD 北大核心 2024年第1期193-200,共8页
针对复杂杂波背景下目标信杂比起伏而导致的漏检问题,本文结合信息几何检测器的性能优势与动态规划检测前跟踪(Dynamic Programming Track Before Detect,DP-TBD)的多帧信息积累能力,提出了基于功率谱流形的信息几何DP-TBD算法.该算法... 针对复杂杂波背景下目标信杂比起伏而导致的漏检问题,本文结合信息几何检测器的性能优势与动态规划检测前跟踪(Dynamic Programming Track Before Detect,DP-TBD)的多帧信息积累能力,提出了基于功率谱流形的信息几何DP-TBD算法.该算法利用功率谱流形与矩阵流形对偶关系,设计了功率谱信息几何检测器,将信息几何检测器的计算复杂度降低了近两个数量级.通过实测数据实验验证,功率谱DP-TBD算法可实现与矩阵DP-TBD算法相近的检测性能,并将运算时间降低为矩阵DP-TBD算法的3%~8%.此外,相较于信息几何检测器,功率谱DP-TBD可将检测信杂比(Signal-to-Clutter Ratio,SCR)提高2~3 dB. 展开更多
关键词 雷达目标检测 信息几何检测器 检测前跟踪 功率谱流形 动态规划
下载PDF
基于有限时间ADP的微波加热高钛渣温度跟踪控制
3
作者 杨彪 杜婉 +3 位作者 李鑫培 高皓 刘承 马红涛 《控制工程》 CSCD 北大核心 2024年第2期193-202,共10页
针对常规控制方法对微波加热过程控制效果不够理想的问题,提出一种基于数据驱动模型的有限时间自适应动态规划微波加热温度跟踪算法。算法包含模型网络、评价网络和执行网络,这3个网络的实现依赖于神经网络。模型网络实现微波加热过程... 针对常规控制方法对微波加热过程控制效果不够理想的问题,提出一种基于数据驱动模型的有限时间自适应动态规划微波加热温度跟踪算法。算法包含模型网络、评价网络和执行网络,这3个网络的实现依赖于神经网络。模型网络实现微波加热过程的数据驱动建模,评价网络和执行网络实现最优性能指标函数和控制功率的逼近。最后将温度跟踪转化为误差的镇定。通过理论推导证明了算法的收敛性及最优性,并进一步开展了微波加热高钛渣温度跟踪实验和仿真研究。结果表明,算法能有效地跟踪高钛渣的加热过程,基于ELMAN神经网络的模型预测误差小于1℃,温度跟踪误差小于0.2℃,在工业微波加热中具有潜在的应用价值。 展开更多
关键词 微波加热 高钛渣 有限时间 自适应动态规划 神经网络
下载PDF
基于DP83640的秒脉冲移相器设计与实现
4
作者 崔海波 王康 武建锋 《导航定位与授时》 CSCD 2024年第1期133-142,共10页
使用DP83640 IEEE 1588精密时间协议(PTP)收发芯片设计实现了一款秒脉冲精密移相器,它能与外部的标准秒脉冲(1 PPS)进行同步并进行精密相位微调,可应用于高精度相位微跃器。秒脉冲移相器采用DP83640芯片进行级联实现秒脉冲精密移相:利用... 使用DP83640 IEEE 1588精密时间协议(PTP)收发芯片设计实现了一款秒脉冲精密移相器,它能与外部的标准秒脉冲(1 PPS)进行同步并进行精密相位微调,可应用于高精度相位微跃器。秒脉冲移相器采用DP83640芯片进行级联实现秒脉冲精密移相:利用ARM微处理器控制第二级DP83640实现与外部标准秒脉冲的相位粗调,控制第一级DP83640实现相位微调。相位调整时将外部输入的相位偏移量换算为8 ns整周期倍数的相位粗调值,以及不同时间长度档位的相位微调值,分别写入第二级和第一级DP83640共同实现高精度相位微跃。由于硬件电路特性和器件综合噪声的影响,经测试平均相位微跃准确度可以达到0.1 fs。 展开更多
关键词 秒脉冲精密移相器 dp83640 相位微跃 精密相位调整
下载PDF
木塑材料3DP打印机运动控制系统轨迹跟踪研究
5
作者 王琦 刘子昕 +2 位作者 王鑫旭 李晓旭 闫承琳 《林业工程学报》 CSCD 北大核心 2024年第3期127-137,共11页
针对木塑材料3DP打印机运动控制系统X轴负载较大而导致CoreXY机构在进行开环控制时打印精度较差的问题,研究3DP打印机的模型预测控制(MPC)智能轨迹跟踪算法,提高打印精度和打印速度。基于黏结剂喷射(3DP)成型工艺和CoreXY机构的传动特... 针对木塑材料3DP打印机运动控制系统X轴负载较大而导致CoreXY机构在进行开环控制时打印精度较差的问题,研究3DP打印机的模型预测控制(MPC)智能轨迹跟踪算法,提高打印精度和打印速度。基于黏结剂喷射(3DP)成型工艺和CoreXY机构的传动特点设计了木塑材料3DP打印机运动控制系统,提出了一种适用于3DP打印机的MPC轨迹跟踪策略。采用笛卡尔坐标系下近似圆形切片的打印轨迹作为参考轨迹,建立CoreXY机构A、B电机闭环系统的预测模型,运用MPC理论将打印速度和精度的多约束最优控制问题变为带约束的二次函数进行求解,对比参考轨迹与实际打印轨迹之间的误差,进而研究不同打印速度对轨迹跟踪效果的影响。对仿真结果进行分析计算得出,打印速度在80~400 mm/s范围内,3DP打印机的喷胶位点均可实现对参考轨迹的较准确跟踪,A、B电机皮带位移最大横向误差分别为0.0097和0.0060 mm,X、Y轴横向误差的平均绝对误差分别为0.357和0.362 mm。对比PID控制,MPC控制策略的各项衡量指标都更优,且参数更易整定,横向误差更小,提高了3DP打印机喷射路径的准确度和效率。随着打印速度的降低,MPC控制器的横向误差逐渐减小,系统的轨迹跟踪效果更准确和稳定,最终绘制参考轨迹与实际轨迹形状基本重合。 展开更多
关键词 3dp打印机 模型预测控制(MPC) 轨迹跟踪 CoreXY机构 3dp工艺
下载PDF
Recent Progress in Reinforcement Learning and Adaptive Dynamic Programming for Advanced Control Applications 被引量:1
6
作者 Ding Wang Ning Gao +2 位作者 Derong Liu Jinna Li Frank L.Lewis 《IEEE/CAA Journal of Automatica Sinica》 SCIE EI CSCD 2024年第1期18-36,共19页
Reinforcement learning(RL) has roots in dynamic programming and it is called adaptive/approximate dynamic programming(ADP) within the control community. This paper reviews recent developments in ADP along with RL and ... Reinforcement learning(RL) has roots in dynamic programming and it is called adaptive/approximate dynamic programming(ADP) within the control community. This paper reviews recent developments in ADP along with RL and its applications to various advanced control fields. First, the background of the development of ADP is described, emphasizing the significance of regulation and tracking control problems. Some effective offline and online algorithms for ADP/adaptive critic control are displayed, where the main results towards discrete-time systems and continuous-time systems are surveyed, respectively.Then, the research progress on adaptive critic control based on the event-triggered framework and under uncertain environment is discussed, respectively, where event-based design, robust stabilization, and game design are reviewed. Moreover, the extensions of ADP for addressing control problems under complex environment attract enormous attention. The ADP architecture is revisited under the perspective of data-driven and RL frameworks,showing how they promote ADP formulation significantly.Finally, several typical control applications with respect to RL and ADP are summarized, particularly in the fields of wastewater treatment processes and power systems, followed by some general prospects for future research. Overall, the comprehensive survey on ADP and RL for advanced control applications has d emonstrated its remarkable potential within the artificial intelligence era. In addition, it also plays a vital role in promoting environmental protection and industrial intelligence. 展开更多
关键词 Adaptive dynamic programming(Adp) advanced control complex environment data-driven control event-triggered design intelligent control neural networks nonlinear systems optimal control reinforcement learning(RL)
下载PDF
In vivo astrocyte reprogramming following spinal cord injury
7
作者 Yannick N.Gerber Florence E.Perrin 《Neural Regeneration Research》 SCIE CAS CSCD 2024年第3期487-488,共2页
Harmful and helpful roles of astrocytes in spinal cord injury(SCI):SCI induce gradable sensory,motor and autonomic impairments that correlate with the lesion severity and the rostro-caudal location of the injury site.... Harmful and helpful roles of astrocytes in spinal cord injury(SCI):SCI induce gradable sensory,motor and autonomic impairments that correlate with the lesion severity and the rostro-caudal location of the injury site.The absence of spontaneous axonal regeneration after injury results from neuron-intrinsic and neuron-extrinsic parameters.Indeed,not only adult neurons display limited capability to regrow axons but also the injury environment contains inhibitors to axonal regeneration and a lack of growth-promoting factors.Amongst other cell populations that respond to the lesion,reactive astrocytes were first considered as only detrimental to spontaneous axonal regeneration.Indeed,astrocytes. 展开更多
关键词 INJURY IMPAIRMENT programming
下载PDF
Transcriptional reprogramming during human osteoclast differentiation identifies regulators of osteoclast activity
8
作者 Morten S.Hansen Kaja Madsen +6 位作者 Maria Price Kent Søe Yasunori Omata Mario M.Zaiss Caroline M.Gorvin Morten Frost Alexander Rauch 《Bone Research》 SCIE CAS CSCD 2024年第1期180-198,共19页
Enhanced osteoclastogenesis and osteoclast activity contribute to the development of osteoporosis,which is characterized by increased bone resorption and inadequate bone formation.As novel antiosteoporotic therapeutic... Enhanced osteoclastogenesis and osteoclast activity contribute to the development of osteoporosis,which is characterized by increased bone resorption and inadequate bone formation.As novel antiosteoporotic therapeutics are needed,understanding the genetic regulation of human osteoclastogenesis could help identify potential treatment targets.This study aimed to provide an overview of transcriptional reprogramming during human osteoclast differentiation.Osteoclasts were differentiated from CD14+monocytes from eight female donors.RNA sequencing during differentiation revealed 8980 differentially expressed genes grouped into eight temporal patterns conserved across donors.These patterns revealed distinct molecular functions associated with postmenopausal osteoporosis susceptibility genes based on RNA from iliac crest biopsies and bone mineral density SNPs.Network analyses revealed mutual dependencies between temporal expression patterns and provided insight into subtype-specific transcriptional networks.The donor-specific expression patterns revealed genes at the monocyte stage,such as filamin B(FLNB)and oxidized low-density lipoprotein receptor 1(OLR1,encoding LOX-1),that are predictive of the resorptive activity of mature osteoclasts.The expression of differentially expressed G-protein coupled receptors was strong during osteoclast differentiation,and these receptors are associated with bone mineral density SNPs,suggesting that they play a pivotal role in osteoclast differentiation and activity.The regulatory effects of three differentially expressed G-protein coupled receptors were exemplified by in vitro pharmacological modulation of complement 5 A receptor 1(C5AR1),somatostatin receptor 2(SSTR2),and free fatty acid receptor 4(FFAR4/GPR120).Activating C5AR1 enhanced osteoclast formation,while activating SSTR2 decreased the resorptive activity of mature osteoclasts,and activating FFAR4 decreased both the number and resorptive activity of mature osteoclasts.In conclusion,we report the occurrence of transcriptional reprogramming during human osteoclast differentiation and identified SSTR2 and FFAR4 as antiresorptive G-protein coupled receptors and FLNB and LOX-1 as potential molecular markers of osteoclast activity.These data can help future investigations identify molecular regulators of osteoclast differentiation and activity and provide the basis for novel antiosteoporotic targets. 展开更多
关键词 OSTEOCLAST programming identif
下载PDF
Uncertainty quantification of inverse analysis for geomaterials using probabilistic programming
9
作者 Hongbo Zhao Shaojun Li +3 位作者 Xiaoyu Zang Xinyi Liu Lin Zhang Jiaolong Ren 《Journal of Rock Mechanics and Geotechnical Engineering》 SCIE CSCD 2024年第3期895-908,共14页
Uncertainty is an essentially challenging for safe construction and long-term stability of geotechnical engineering.The inverse analysis is commonly utilized to determine the physico-mechanical parameters.However,conv... Uncertainty is an essentially challenging for safe construction and long-term stability of geotechnical engineering.The inverse analysis is commonly utilized to determine the physico-mechanical parameters.However,conventional inverse analysis cannot deal with uncertainty in geotechnical and geological systems.In this study,a framework was developed to evaluate and quantify uncertainty in inverse analysis based on the reduced-order model(ROM)and probabilistic programming.The ROM was utilized to capture the mechanical and deformation properties of surrounding rock mass in geomechanical problems.Probabilistic programming was employed to evaluate uncertainty during construction in geotechnical engineering.A circular tunnel was then used to illustrate the proposed framework using analytical and numerical solution.The results show that the geomechanical parameters and associated uncertainty can be properly obtained and the proposed framework can capture the mechanical behaviors under uncertainty.Then,a slope case was employed to demonstrate the performance of the developed framework.The results prove that the proposed framework provides a scientific,feasible,and effective tool to characterize the properties and physical mechanism of geomaterials under uncertainty in geotechnical engineering problems. 展开更多
关键词 Geological engineering Geotechnical engineering Inverse analysis Uncertainty quantification Probabilistic programming
下载PDF
基于Gissmo失效准则的DP590双相钢和热成形钢的断裂特性研究
10
作者 朱建琳 王超超 王秋月 《塑性工程学报》 CAS CSCD 北大核心 2024年第2期163-172,共10页
首先对车身上常用的DP590双相钢和热成形钢进行了6种不同应力三轴度下的试验研究,获取了材料的基本力学特性。使用Ludwike硬化模型获取了材料颈缩后的真实塑性应力-真实塑性应变曲线,并通过对比颈缩较小的纯剪切工况仿真模拟结果与试验... 首先对车身上常用的DP590双相钢和热成形钢进行了6种不同应力三轴度下的试验研究,获取了材料的基本力学特性。使用Ludwike硬化模型获取了材料颈缩后的真实塑性应力-真实塑性应变曲线,并通过对比颈缩较小的纯剪切工况仿真模拟结果与试验结果验证了外插曲线的正确性。通过仿真逆向优化的方式,使用LS-OPT软件获取了可以描述材料非线性损伤的Gissmo失效模型参数。为快速准确地获取模型参数,提出了一种获取待优化参数初始值并采用不同应力三轴度区间开展模型系数优化的方法。最后,开展了未参与优化的60°拉剪和R 6缺口工况的仿真模拟,仿真结果与试验结果一致,从而验证了模型参数的正确性。 展开更多
关键词 dp590双相钢 热成形钢 断裂模型 Gissmo
下载PDF
Rapid Prototype Development Approach for Genetic Programming
11
作者 Pei He Lei Zhang 《Journal of Computer and Communications》 2024年第2期67-79,共13页
Genetic Programming (GP) is an important approach to deal with complex problem analysis and modeling, and has been applied in a wide range of areas. The development of GP involves various aspects, including design of ... Genetic Programming (GP) is an important approach to deal with complex problem analysis and modeling, and has been applied in a wide range of areas. The development of GP involves various aspects, including design of genetic operators, evolutionary controls and implementations of heuristic strategy, evaluations and other mechanisms. When designing genetic operators, it is necessary to consider the possible limitations of encoding methods of individuals. And when selecting evolutionary control strategies, it is also necessary to balance search efficiency and diversity based on representation characteristics as well as the problem itself. More importantly, all of these matters, among others, have to be implemented through tedious coding work. Therefore, GP development is both complex and time-consuming. To overcome some of these difficulties that hinder the enhancement of GP development efficiency, we explore the feasibility of mutual assistance among GP variants, and then propose a rapid GP prototyping development method based on πGrammatical Evolution (πGE). It is demonstrated through regression analysis experiments that not only is this method beneficial for the GP developers to get rid of some tedious implementations, but also enables them to concentrate on the essence of the referred problem, such as individual representation, decoding means and evaluation. Additionally, it provides new insights into the roles of individual delineations in phenotypes and semantic research of individuals. 展开更多
关键词 Genetic programming Grammatical Evolution Gene Expression programming Regression Analysis Mathematical Modeling Rapid Prototype Development
下载PDF
DP1180和S700MC异种高强钢激光焊接接头的组织和性能
12
作者 汪杨 王山 +1 位作者 刘成杰 黎其俊 《上海金属》 CAS 2024年第2期64-70,共7页
采用激光搭接焊对DP1180和S700MC异种高强钢进行焊接,研究了焊接接头的微观组织和力学性能,并与DP1180同种钢焊接接头进行了对比。结果表明:DP1180和S700MC异种钢焊缝的横截面呈Y形,而DP1180同种钢焊缝的横截面呈V形;异种钢搭接焊接头的... 采用激光搭接焊对DP1180和S700MC异种高强钢进行焊接,研究了焊接接头的微观组织和力学性能,并与DP1180同种钢焊接接头进行了对比。结果表明:DP1180和S700MC异种钢焊缝的横截面呈Y形,而DP1180同种钢焊缝的横截面呈V形;异种钢搭接焊接头的DP1180钢侧热影响区分别出现了软化和硬化现象,而S700MC钢侧热影响区只出现了较为严重的硬化现象,并没有明显的软化现象;在相同的熔宽条件下,DP1180和S700MC异种钢接头的拉剪力明显小于DP1180同种钢接头,但仍高于S700MC钢母材;所有接头的拉伸性能稳定,力学性能良好,并且同种钢和异种钢焊接均可通过增加焊长来提升焊接接头的承载性能。 展开更多
关键词 dp1180钢 异种材料 激光搭接焊 显微组织 力学性能
下载PDF
6061铝合金/DP600钢电阻点焊接头特征及力学性能
13
作者 赵红光 翁福娟 张勇 《精密成形工程》 北大核心 2024年第2期130-136,共7页
目的提升6061-T6铝合金/DP600双相钢电阻点焊接头的力学性能,以满足该焊接结构在汽车工业中的应用。方法对6061-T6铝合金与DP600双相钢分别进行了直接电阻点焊试验及添加Ni中间层的电阻点焊试验,采用光学显微镜、扫描电子显微镜及能谱... 目的提升6061-T6铝合金/DP600双相钢电阻点焊接头的力学性能,以满足该焊接结构在汽车工业中的应用。方法对6061-T6铝合金与DP600双相钢分别进行了直接电阻点焊试验及添加Ni中间层的电阻点焊试验,采用光学显微镜、扫描电子显微镜及能谱仪分析了接头界面宏微观组织、化学成分、元素分布等,此外还采用接头拉剪试验进行了2种接头的力学性能测试,并对接头的断口形貌及断裂模式进行了分析。结果直接点焊接头熔核界面形成了厚度约为2.5μm的金属间化合物层,主要金属间化合物为靠近铝合金侧的Fe_(2)A_(l5)及靠近高强钢侧的Fe_(4)Al_(13)。直接点焊接头的拉剪载荷为3.1 kN,失效形式为界面断裂,断口呈以脆性为主的混合断裂特征。添加Ni中间层的点焊接头界面形成了Ni_(4)Al_(13)、Ni_(2)Al_(5)金属间化合物,抑制了焊接过程中Al-Fe互扩散并降低了Al-Fe金属间化合物的形成以及硬脆性Al-Fe金属间化合物对接头力学性能的影响,使接头拉剪载荷提高了67.7%,达到了5.2 kN,断口呈以韧性为主的混合断裂特征。结论添加Ni中间层可显著提升6061-T6铝合金/DP600双相钢电阻点焊接头的力学性能。 展开更多
关键词 6061-T6铝合金 dp600双相钢 电阻点焊 组织特征 力学性能
下载PDF
三用工作船DP系统案例故障分析与排除
14
作者 陈宏雀 孙立业 《珠江水运》 2024年第8期8-11,共4页
随着科学技术的不断发展,船舶自动化、智能化程度与时俱进,船舶动力定位(Dynamic Positioning,以下简称:DP)系统在海洋工程船舶上得到推广和应用。其中,DP2系统运用较为广泛。高度集成智能化的DP2系统提供便利的同时也给船舶设备管理人... 随着科学技术的不断发展,船舶自动化、智能化程度与时俱进,船舶动力定位(Dynamic Positioning,以下简称:DP)系统在海洋工程船舶上得到推广和应用。其中,DP2系统运用较为广泛。高度集成智能化的DP2系统提供便利的同时也给船舶设备管理人员带来挑战。本文通过某三用工作船DP2系统故障分析和处理过程,总结DP2系统故障处理方法,为船舶DP2系统故障处理提供经验分享。 展开更多
关键词 dp2 三用工作船 故障分析
下载PDF
高强钢DP780压扁开裂原因分析
15
作者 李增丰 刘宇 《山西冶金》 CAS 2024年第3期35-36,39,共3页
随着汽车轻量化的发展,先进高强钢材料的应用成为减轻车身重量和提高汽车防撞性能的重要途径。某厂家采用连退DP780高强钢通过辊压工艺加工圆管生产座椅骨架,但检验压扁工艺性能时,试样出现开裂现象。对压扁开裂试样和合格试样进行理化... 随着汽车轻量化的发展,先进高强钢材料的应用成为减轻车身重量和提高汽车防撞性能的重要途径。某厂家采用连退DP780高强钢通过辊压工艺加工圆管生产座椅骨架,但检验压扁工艺性能时,试样出现开裂现象。对压扁开裂试样和合格试样进行理化检验分析,扫描电镜和金相分析未发现明显夹杂物,压扁开裂试样金相组织较合格试样有粗大的块状马氏体,合格件马氏体细小,弥散分布在铁素体基体中。进行折弯性能和扩孔性能实验分析,压扁开裂样板180°折弯后,出现了开裂现象,其扩孔率为20.3%,低于合格样板的24.7%。综合分析,成分体系的差异造成开裂产品组织晶粒较为粗大,变形过程晶粒间协调性差,以及低的折弯性能和扩孔性能,是此次圆管压扁开裂的主要原因。 展开更多
关键词 780dp 压扁开裂 合金元素 组织 扩孔率
下载PDF
Adaptive Optimal Discrete-Time Output-Feedback Using an Internal Model Principle and Adaptive Dynamic Programming
16
作者 Zhongyang Wang Youqing Wang Zdzisław Kowalczuk 《IEEE/CAA Journal of Automatica Sinica》 SCIE EI CSCD 2024年第1期131-140,共10页
In order to address the output feedback issue for linear discrete-time systems, this work suggests a brand-new adaptive dynamic programming(ADP) technique based on the internal model principle(IMP). The proposed metho... In order to address the output feedback issue for linear discrete-time systems, this work suggests a brand-new adaptive dynamic programming(ADP) technique based on the internal model principle(IMP). The proposed method, termed as IMP-ADP, does not require complete state feedback-merely the measurement of input and output data. More specifically, based on the IMP, the output control problem can first be converted into a stabilization problem. We then design an observer to reproduce the full state of the system by measuring the inputs and outputs. Moreover, this technique includes both a policy iteration algorithm and a value iteration algorithm to determine the optimal feedback gain without using a dynamic system model. It is important that with this concept one does not need to solve the regulator equation. Finally, this control method was tested on an inverter system of grid-connected LCLs to demonstrate that the proposed method provides the desired performance in terms of both tracking and disturbance rejection. 展开更多
关键词 Adaptive dynamic programming(Adp) internal model principle(IMP) output feedback problem policy iteration(PI) value iteration(VI)
下载PDF
A Dimensional Reduction Approach Based on Essential Constraints in Linear Programming
17
作者 Eirini I. Nikolopoulou George S. Androulakis 《American Journal of Operations Research》 2024年第1期1-31,共31页
This paper presents a new dimension reduction strategy for medium and large-scale linear programming problems. The proposed method uses a subset of the original constraints and combines two algorithms: the weighted av... This paper presents a new dimension reduction strategy for medium and large-scale linear programming problems. The proposed method uses a subset of the original constraints and combines two algorithms: the weighted average and the cosine simplex algorithm. The first approach identifies binding constraints by using the weighted average of each constraint, whereas the second algorithm is based on the cosine similarity between the vector of the objective function and the constraints. These two approaches are complementary, and when used together, they locate the essential subset of initial constraints required for solving medium and large-scale linear programming problems. After reducing the dimension of the linear programming problem using the subset of the essential constraints, the solution method can be chosen from any suitable method for linear programming. The proposed approach was applied to a set of well-known benchmarks as well as more than 2000 random medium and large-scale linear programming problems. The results are promising, indicating that the new approach contributes to the reduction of both the size of the problems and the total number of iterations required. A tree-based classification model also confirmed the need for combining the two approaches. A detailed numerical example, the general numerical results, and the statistical analysis for the decision tree procedure are presented. 展开更多
关键词 Linear programming Binding Constraints Dimension Reduction Cosine Similarity Decision Analysis Decision Trees
下载PDF
Profibus-DP总线在印染拉幅定形机电气控制系统上的应用
18
作者 周振环 《产业用纺织品》 2024年第2期48-52,共5页
对印染拉幅定形机的电气控制系统进行概述。该系统采用先进的西门子Profibus-DP总线通信技术,配备丹佛斯FC302变频器构成速度闭环控制方式。通过信号级联输出方式,实现各传动单元之间的速度同步,提高速度信号的实时性和精确度。此外,介... 对印染拉幅定形机的电气控制系统进行概述。该系统采用先进的西门子Profibus-DP总线通信技术,配备丹佛斯FC302变频器构成速度闭环控制方式。通过信号级联输出方式,实现各传动单元之间的速度同步,提高速度信号的实时性和精确度。此外,介绍了风机变频器和温控表所采用的Modbus总线通信方式,该通信方式实现了更好的设备数据整合与数据交换。 展开更多
关键词 印染拉幅定形机 PROFIBUS-dp总线 速度闭环 触摸屏 MODBUS总线 变频器 信号级联 可编程逻辑控制器
下载PDF
基于DP准则的巷道围岩塑性区影响因素分析 被引量:1
19
作者 经来旺 张世翔 +2 位作者 肖起辉 方旭 经纬 《中国矿业》 2023年第1期150-157,共8页
围岩塑性区的扩展是巷道事故频发的根本原因,确定塑性区影响因素及其发展规律对煤矿的安全生产至关重要。基于DP准则推导出非均匀场下的围岩塑性区边界方程,对非圆形截面巷道进行当量半径折算,分析不同侧压系数下塑性区形态,采用单因素... 围岩塑性区的扩展是巷道事故频发的根本原因,确定塑性区影响因素及其发展规律对煤矿的安全生产至关重要。基于DP准则推导出非均匀场下的围岩塑性区边界方程,对非圆形截面巷道进行当量半径折算,分析不同侧压系数下塑性区形态,采用单因素法分析不同DP准则的塑性区影响因素。研究结果表明:当侧压系数在0.6~1.5范围时,塑性区呈椭圆形分布;当侧压系数小于0.6或大于1.5时,塑性区呈蝶形分布。巷道地压和围岩岩性显著影响了塑性区的形态及范围,根据工程实际合理选取巷道位置,能够有效降低巷道支护的难度及成本。中间主应力对巷道围岩塑性区范围的影响有着强烈的区间性。巷道支护可以通过注浆来改善岩体的黏聚力、内摩擦角,进而减小塑性区范围,但这一作用效果有限。塑性区半径随着支护阻力的增大而线性减小。根据不同DP准则计算出的塑性区半径有所差异,合理运用DP屈服准则既能够保证煤炭生产的安全性,又能够降低工程造价。 展开更多
关键词 dp准则 当量半径 塑性区 侧压系数
下载PDF
连退工艺对DP980钢显微组织、织构及性能的影响
20
作者 王卫卫 刘浏 李光灜 《热加工工艺》 北大核心 2023年第2期140-142,150,共4页
设定连续退火工艺试验参数,系统研究了连续退火工艺对高强塑性冷轧双相钢DP980显微组织、织构及力学性能的影响。结果表明,随着退火温度的提高,退火织构组分明显增加,剪切织构组分逐渐下降。其余织构组分没有明显特点,随机产生。退火织... 设定连续退火工艺试验参数,系统研究了连续退火工艺对高强塑性冷轧双相钢DP980显微组织、织构及力学性能的影响。结果表明,随着退火温度的提高,退火织构组分明显增加,剪切织构组分逐渐下降。其余织构组分没有明显特点,随机产生。退火织构明显加强有利于连退后屈服强度和抗拉强度的逐渐升高,使冷轧DP980钢的强塑积达到15 GPa·%。 展开更多
关键词 dp980 连续退火工艺 再结晶晶粒 高伸长率 织构
下载PDF
上一页 1 2 250 下一页 到第
使用帮助 返回顶部