Carbonated recycled powder as cementitious auxiliary material can reduce carbon emissions and realize high-quality recycling of recycled concrete.In this paper,microscopic property of recycled powder with three carbon...Carbonated recycled powder as cementitious auxiliary material can reduce carbon emissions and realize high-quality recycling of recycled concrete.In this paper,microscopic property of recycled powder with three carbonation methods was tested through XRD and SEM,the mechanical property and microstructure of recycled powder mortar with three replacement rates were studied by ISO method and SEM,and the strengthening mechanism was analyzed.The results showed that the mechanical property of recycled powder mortar decreased with the increasing of replacement rate.It is suggested that the replacement rate of recycled powder should not exceed 20%.The strength index and activity index of carbonated recycled powder mortar were improved,in which the flexural strength was increased by 27.85%and compressive strength was increased by 20%at the maximum.Recycled powder can be quickly and completely carbonated,and the improvement effect of CH pre-soaking carbonation was the best.The activity index of carbonated recycled powder can meet the requirements of Grade II technical standard for recycled powder.Microscopic results revealed the activation mechanism of carbonated recycled powder such as surplus calcium source effect,alkaline polycondensation effect and carbonation enhancement effect.展开更多
Cryogenic treatment was used to improve the tribological properties of Ti6Al4V artificial hip joint implants.Cryogenic treatment at-196℃with different holding time were carried out on Ti6Al4V specimens fabricated usi...Cryogenic treatment was used to improve the tribological properties of Ti6Al4V artificial hip joint implants.Cryogenic treatment at-196℃with different holding time were carried out on Ti6Al4V specimens fabricated using electron beam melting(EBM),and their microstructure and tribological properties evolution were systematically analyzed by scanning electron microscopy(SEM),vickers hardness,and wear tests.The experimental results show that the as-fabricated specimen consists of lamellarαphase andβcolumnar crystal.While,the thickness of lamellarαphase decreased after cryogenic treatment.In addition,it can be found that the fineαphase was precipitated and dispersed between the lamellarαphase with the holding time increase.Vickers hardness shows a trend of first increasing and then decreasing.The wear rate of the specimen cryogenic treated for 24 h is the minimum and the average friction coefficient is 0.50,which is reduced by 14.61%compared with the as-fabricated.The wear mechanism of the as-fabricated specimen is severe exfoliation,adhesive,abrasive,and slight fatigue wear.However,the specimen cryogenic treated for 24 h shows slight adhesive and abrasive wear.It can be concluded that it is feasibility of utilizing cryogenic treatment to reduce the wear of EBMed Ti6Al4V.展开更多
Strong impact does serious harm to the military industries so it is necessary to choose reasonable cushioning material and design effective buffers to prevent the impact of equipment.Based on the capillary property en...Strong impact does serious harm to the military industries so it is necessary to choose reasonable cushioning material and design effective buffers to prevent the impact of equipment.Based on the capillary property entangled porous metallic wire materials(EPMWM),this paper designed a composite buffer which uses EPMWM and viscous fluid as cushioning materials under the low-speed impact of the recoil force device of weapon equipment(such as artillery,mortar,etc.).Combined with the capillary model,porosity,hydraulic diameter,maximum pore diameter and pore distribution were used to characterize the pore structure characteristics of EPMWM.The calculation model of the damping force of the composite buffer was established.The low-speed impact test of the composite buffer was conducted.The parameters of the buffer under low-speed impact were identified according to the model,and the nonlinear model of damping force was obtained.The test results show that the composite buffer with EPMWM and viscous fluid can absorb the impact energy from the recoil movement effectively,and provide a new method for the buffer design of weapon equipment(such as artillery,mortar,etc.).展开更多
The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron mi...The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).展开更多
Recently,exploration breakthroughs have been made in the Lower Cretaceous sandstone reservoirs in the Doseo Basin,but the identification of reservoir fluid property is difficult due to variable reservoir lithology,com...Recently,exploration breakthroughs have been made in the Lower Cretaceous sandstone reservoirs in the Doseo Basin,but the identification of reservoir fluid property is difficult due to variable reservoir lithology,complex oil-water contact within and faint responses of the oil zone,which causes the lower accuracy of reservoir fluid property identification with conventional mudlogging and wirelogging techniques.Applying the geochemical logging,fluorescent logging,mud logging and cutting logging technology,in combination with formation test data,this paper distinguishes the crude oil types,analyzes the logging response characteristics of oil zone after water washing,and establishes the interpretation charts and parameter standards for reservoir fluid properties.The crude oil can be divided into two types,namely viscous-heavy and thin-light,based on total hydrocarbon content and component concentration tested by mud logging,features of pyrolysis gas chromatogram and fluorescence spectroscopy.The general characteristics of oil layers experienced water washing include the decrease of total hydrocarbon content and component concentration from mud logging,the decrease of S1 and PS values from geochemical logging,the decrease of hydrocarbon abundance and absence of some light components in pyrolysis gas chromatogram,and the decrease of fluorescence area and intensity from fluorescence logging.According to crude oil types,the cross plots of S1 versus peak-baseline ratio,and the cross plots of rock wettability versus fluorescence area ratio are drawn and used to interpret reservoir fluid property.Meanwhile,the standards of reservoir fluid parameter are established combining with the parameters of PS and the parameters in above charts,and comprehensive multiparameter correlation in both vertical and horizontal ways is also performed to interpret reservoir fluid property.The application in the Doseo Basin achieved great success,improving interpretation ability of fluid property in the reservoir with complex oil-water contact,and also provided technical reference for the efficient exploration and development of similar reservoirs.展开更多
Reservoirs provide a variety of services with economic values across multiple sectors. As demands for reservoir services continue to grow and precipitation patterns evolve, it becomes ever more important to consider t...Reservoirs provide a variety of services with economic values across multiple sectors. As demands for reservoir services continue to grow and precipitation patterns evolve, it becomes ever more important to consider the integrated suite of values and tradeoffs that attend changes in water uses and availability. Section 316 (b) of the Clean Water Act requires that owners of certain water cooled power plants evaluate technologies and operational measures that can reduce their impacts to aquatic organisms. The studies must discuss the social costs and benefits of alternative technologies including cooling towers (79 Fed. Reg. 158, 48300 - 48439). Cooling towers achieve their effect through evaporation. This manuscript estimates the property value, recreation, and hydroelectric generation impacts that could result from the evaporative water loss associated with installing cooling towers at the McGuire Nuclear Generating Station (McGuire) located on Lake Norman, North Carolina. Although this study specifically evaluates the effects of evaporative water loss from cooling towers, its methods are applicable to estimating the economic benefits and costs of a new water user or reduced water input in any complex reservoir system that supports steam electric generation, hydroelectric generation, residential properties, recreation, irrigation, and municipal water use.展开更多
Double-layer structure of seal coating which consisted of a Ni5Al bond coating and a Ni25 graphite top coating were prepared on steel substrate of gas turbine compressor cylinder block.Bond coating was prepared by atm...Double-layer structure of seal coating which consisted of a Ni5Al bond coating and a Ni25 graphite top coating were prepared on steel substrate of gas turbine compressor cylinder block.Bond coating was prepared by atmospheric plasma spraying and top coating was prepared by flame spraying.The microstructure,mechanical properties and abradability of the coating were characterized by scanning elec-tron microscope(SEM),hardness tester,universal testing machine,thermal shock testing machine and abradability testing machine.The res-ults show that the overall spraying structure of the seal coating is uniform,the nickel metal phase is the skeleton supporting the entire coat-ing,and the coating is well bonded without separation.The seal coating has a bonding strength of not less than 7.7 MPa,excellent thermal stability,and thermal shock resistance cycle numbers at 500℃more than 50;the scratch length,deepest invasion depth and wear amount of the coating increase with rise of test temperature,with almost no coating adhesion,indicating that the seal coating has excellent abradability.展开更多
The main obstacle to the open sharing of scientific data is the lack of a legal protection system for intellectual property.This article analyzes the progress of research papers on intellectual property in scientific ...The main obstacle to the open sharing of scientific data is the lack of a legal protection system for intellectual property.This article analyzes the progress of research papers on intellectual property in scientific data in China through literature search and statistics.Currently,research subjects are unbalanced,research content is uneven,research methods are intellectual single,and research depth is insufficient.It is recommended that different stakeholders engage in deep cross disciplinary cooperation,further improve China’s legal and policy protection system for scientific data intellectual property,and promote the open sharing of scientific data.展开更多
In the reform process of the rural land property rights system,the incentive mechanism of the rural land property rights system has a crucial impact on the production activities of rural economic entities.Due to the d...In the reform process of the rural land property rights system,the incentive mechanism of the rural land property rights system has a crucial impact on the production activities of rural economic entities.Due to the different rights structures of the property rights system in different social and economic development stages,the land rights and interests enjoyed by rural economic subjects are different,and the degree of incentives for farmers is also different.This difference in incentives affects farmers investment in agricultural production factors,which in turn affects agricultural performance.This paper analyzes the incentive impacts of the structure of rural land property rights on the changes of farmers land rights and agricultural performance since the founding of the People s Republic of China,in order to further deepen the reform of the land system,protect the rights and interests of farmers,promote the modernization of agriculture and rural areas,and explore the realization form and operation mechanism of the rural collective land system in the new era.展开更多
In this paper,we define a generalized Lipschitz shadowing property for flows and prove that a flowΦgenerated by a C1vector field X on a closed Riemannian manifold M has this generalized Lipschitz shadowing property i...In this paper,we define a generalized Lipschitz shadowing property for flows and prove that a flowΦgenerated by a C1vector field X on a closed Riemannian manifold M has this generalized Lipschitz shadowing property if and only if it is structurally stable.展开更多
The development of diversified foods such as melons under the big food concept can reduce the pressure on staple food grain.Xinjiang has the advantages of building a new development pattern of dual circulation of dive...The development of diversified foods such as melons under the big food concept can reduce the pressure on staple food grain.Xinjiang has the advantages of building a new development pattern of dual circulation of diversified food industry and establishing a national diversified food safety and high-quality assurance center.The construction of an agricultural power needs the strategic support of an intellectual property power.This paper introduced and studied Xinjiang s melon industry and its agricultural intellectual property resources,analyzed the six main problems,including many idle land resources have not been developed into melon fields and the role of melons in diversified food supply systems not well played.Finally,it proposed to vigorously develop diversified food industries such as melons in Xinjiang and establish an eight-point strategy such as national diversified food safety and high-quality assurance center.展开更多
Face-centered cubic (f.c.c.) high entropy alloys (HEAs) are attracting more and more attention owing to their excellent strength and ductility synergy, irradiation resistance, etc. However, the yield strength of f.c.c...Face-centered cubic (f.c.c.) high entropy alloys (HEAs) are attracting more and more attention owing to their excellent strength and ductility synergy, irradiation resistance, etc. However, the yield strength of f.c.c. HEAs is generally low, significantly limiting their practical applications. Recently, the alloying of W has been evidenced to be able to remarkably improve the mechanical properties of f.c.c. HEAs and is becoming a hot topic in the community of HEAs. To date, when W is introduced, multiple strengthening mechanisms, including solid-solution strengthening, precipitation strengthening (μphase,σphase, and b.c.c. phase), and grain-refinement strengthening, have been discovered to be activated or enhanced. Apart from mechanical properties, the addition of W improves corrosion resistance as W helps to form a dense WO_(3) film on the alloy surface. Until now, despite the extensive studies in the literature, there is no available review paper focusing on the W doping of the f.c.c. HEAs. In that context, the effects of W doping on f.c.c. HEAs were reviewed in this work from three aspects, i.e., microstructure,mechanical property, and corrosion resistance. We expect this work can advance the application of the W alloying strategy in the f.c.c. HEAs.展开更多
Rape is the third largest oil crop in the world and the first one in China.The national average rapeseed yield is only 2077.5 kg/hm^(2),and the rapeseed oil yield is 894 kg/hm^(2).This paper introduced the main types,...Rape is the third largest oil crop in the world and the first one in China.The national average rapeseed yield is only 2077.5 kg/hm^(2),and the rapeseed oil yield is 894 kg/hm^(2).This paper introduced the main types,germplasm resources,breeding bases and breeding progress of Chinese rape,and studied its high-quality varieties,breeding patents and new varieties of agricultural plants.We analyzed the main problems such as serious loss of germplasm resources in Brassica campestris L.and Brassica juncea(L.)Czern.et Coss and weak"agricultural chip"in rape field,and put forward strategies such as strengthening the protection of rape germplasm resources,encouraging the development of"agricultural chip"in rape industry clusters with national advantages and characteristics,and strengthening the protection of agricultural intellectual property rights.展开更多
Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing perform...Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing performance,silver coated porous carbon(Ag@PC)is synthesized by one-step hydro-thermal synthesis process making use of fir as a biomass formwork.Phase compositions,morphological structure,and microwave absorption capability of the Ag@PC has been explored.Research results show that the metallic Ag was successfully reduced and the particles are evenly distributed inward the pores of the carbon formwork,which accelerates graphitization process of the amorphous carbon.The Ag@PC composite without adding polyvinyl pyrrolidone(PVP)exhibits higher dielectric constant and better EM wave dissipating capability.This is because the larger particles of Ag give rise to higher electric conductivity.After combing with frequency selective surface(FSS),the EM wave absorbing performance is further improved and the frequency region below-10 d B is located in8.20-11.75 GHz,and the minimal reflection loss value is-22.5 dB.This work indicates that incorporating metallic Ag particles and FSS provides a valid way to strengthen EM wave absorbing capacity of PC material.展开更多
Only by improving the production capacity of domestic herbal edible oil can China ensure the safety of the supply chain of the important industrial chain of vegetable edible oil in China and practice the big food conc...Only by improving the production capacity of domestic herbal edible oil can China ensure the safety of the supply chain of the important industrial chain of vegetable edible oil in China and practice the big food concept.In addition to rice,maize,and soybean for using as grain and oil,there are eight kinds of herbaceous edible oil crops in Hubei Province,including rape,peanut,sesame,sunflower,perilla(perilla seed),cotton,linen and tiger nut(Cyperus esculentus).This paper studies the main industries of herbaceous edible oil crops and their intellectual property resources in Hubei Province,and analyzes the main problems of its inheritance,innovation and high-quality development under the strategy of strengthening the country with intellectual property.Finally,it proposes the countermeasures of carrying forward and inheriting traditional knowledge and traditional culture,maintaining the biodiversity of crops,strengthening the creation of new plant varieties and breeding patents,and opening up the whole chain of intellectual property rights.展开更多
Only by developing woody edible oilseeds industry can we ensure the safety of the important industrial chain and supply chain of vegetable edible oil in China.There are 13 kinds of woody edible oil plants in Hubei,inc...Only by developing woody edible oilseeds industry can we ensure the safety of the important industrial chain and supply chain of vegetable edible oil in China.There are 13 kinds of woody edible oil plants in Hubei,including Camellia oleifera Abel(oil tea),Juglans regia L.(walnut),Olea europaea L.(olive)and Paeonia suffruticosa(oil peony).This paper studies the main industries of woody edible oilseeds in Hubei Province and their intellectual property resources,and analyzes the main problems in their intellectual property protection,inheritance,innovation and development.Finally,it proposes some strategies,including carrying forward the traditional knowledge related to woody edible oilseeds,innovating the"agricultural chip",creating key counties of national woody edible oil seeds,and developing industrial clusters with national advantages and characteristics.展开更多
In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HE...In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.展开更多
This paper introduced the grape industry in Xinjiang and its agricultural intellectual property resources,and analyzed six major problems such as the ineffective leading role of intellectual property rights in high-qu...This paper introduced the grape industry in Xinjiang and its agricultural intellectual property resources,and analyzed six major problems such as the ineffective leading role of intellectual property rights in high-quality development.Finally,it proposed eight strategies to build a national-level regional fine-grain breeding base for grapes and develop“agricultural chips”in the context of the strategy of strengthening the country with intellectual property and innovation-driven development strategy.展开更多
"Three new developments"is the guiding ideology of Chinese-style high-quality development in the new era.Jujube(Zizyphus jujube Mill.)is a plant of Zizyphus of Rhamnaceae,which originated in China and has be..."Three new developments"is the guiding ideology of Chinese-style high-quality development in the new era.Jujube(Zizyphus jujube Mill.)is a plant of Zizyphus of Rhamnaceae,which originated in China and has been listed as one of the"five fruits"since ancient times.Xinjiang is the most important jujube producing area in China,and its yield has accounted for 50%of the national jujube yield.In the five prefectures and cities of southern Xinjiang,as well as the regimental farms of southern and eastern Xinjiang of Xinjiang Production and Construction Corps,the jujube industry is an advantageous characteristic industry in agriculture.This paper studied Xinjiang jujube industry and its agricultural intellectual property resources,analyzed six major issues to be further implemented,such as the"three new developments"thinking and the strategy of building an intellectual property power,and puts forward eight strategies such as coordinating the two markets and two resources to accelerate the construction of a new development pattern and dual circulation of jujube.展开更多
A comprehensive experimental program has been performed to characterize the hydration and engineering property evolution of a class G oil well cement under various curing temperatures from 30 to 90℃.The progress of h...A comprehensive experimental program has been performed to characterize the hydration and engineering property evolution of a class G oil well cement under various curing temperatures from 30 to 90℃.The progress of hydration was monitored by isothermal calorimetry(atmospheric pressure);the viscosity evolution was measured using a high temperature and high pressure consistometer(up to 200 MPa);the ultrasonic property development was evaluated by an ultrasonic cement analyzer(up to 100 MPa).Test results indicate that the influences of curing temperature and pressure on the hydration,viscosity and ultrasonic property development can be modeled by a scale factor method that is similar to the maturity method used in the concrete industry.However,the key parameters of the scale factor model,namely the apparent activation energy and the apparent activation volume of cement showed obvious variations with test method and curing condition.The test results indicate that the curing temperature has a stronger effect on cement hydration rate than viscosity and ultrasonic property development rate,while the curing pressure has a much stronger influence on cement slurry properties before setting(viscosity)than after setting(ultrasonic property).展开更多
基金Funded by Joint Funds of the National Natural Science Foundation of China(No.U1904188)Jiangxi Provincial Department of Education Science and Technology Project(Nos.GJJ171079,GJJ181023 and GJJ181022)。
文摘Carbonated recycled powder as cementitious auxiliary material can reduce carbon emissions and realize high-quality recycling of recycled concrete.In this paper,microscopic property of recycled powder with three carbonation methods was tested through XRD and SEM,the mechanical property and microstructure of recycled powder mortar with three replacement rates were studied by ISO method and SEM,and the strengthening mechanism was analyzed.The results showed that the mechanical property of recycled powder mortar decreased with the increasing of replacement rate.It is suggested that the replacement rate of recycled powder should not exceed 20%.The strength index and activity index of carbonated recycled powder mortar were improved,in which the flexural strength was increased by 27.85%and compressive strength was increased by 20%at the maximum.Recycled powder can be quickly and completely carbonated,and the improvement effect of CH pre-soaking carbonation was the best.The activity index of carbonated recycled powder can meet the requirements of Grade II technical standard for recycled powder.Microscopic results revealed the activation mechanism of carbonated recycled powder such as surplus calcium source effect,alkaline polycondensation effect and carbonation enhancement effect.
基金Funded by the National Natural Science Foundation of China(No.42102345)the Fundamental Research Funds for the Central Universities(No.2023ZKPYJD03)。
文摘Cryogenic treatment was used to improve the tribological properties of Ti6Al4V artificial hip joint implants.Cryogenic treatment at-196℃with different holding time were carried out on Ti6Al4V specimens fabricated using electron beam melting(EBM),and their microstructure and tribological properties evolution were systematically analyzed by scanning electron microscopy(SEM),vickers hardness,and wear tests.The experimental results show that the as-fabricated specimen consists of lamellarαphase andβcolumnar crystal.While,the thickness of lamellarαphase decreased after cryogenic treatment.In addition,it can be found that the fineαphase was precipitated and dispersed between the lamellarαphase with the holding time increase.Vickers hardness shows a trend of first increasing and then decreasing.The wear rate of the specimen cryogenic treated for 24 h is the minimum and the average friction coefficient is 0.50,which is reduced by 14.61%compared with the as-fabricated.The wear mechanism of the as-fabricated specimen is severe exfoliation,adhesive,abrasive,and slight fatigue wear.However,the specimen cryogenic treated for 24 h shows slight adhesive and abrasive wear.It can be concluded that it is feasibility of utilizing cryogenic treatment to reduce the wear of EBMed Ti6Al4V.
基金supported by the National Natural Science Foundation of China (Grant No.51805086)。
文摘Strong impact does serious harm to the military industries so it is necessary to choose reasonable cushioning material and design effective buffers to prevent the impact of equipment.Based on the capillary property entangled porous metallic wire materials(EPMWM),this paper designed a composite buffer which uses EPMWM and viscous fluid as cushioning materials under the low-speed impact of the recoil force device of weapon equipment(such as artillery,mortar,etc.).Combined with the capillary model,porosity,hydraulic diameter,maximum pore diameter and pore distribution were used to characterize the pore structure characteristics of EPMWM.The calculation model of the damping force of the composite buffer was established.The low-speed impact test of the composite buffer was conducted.The parameters of the buffer under low-speed impact were identified according to the model,and the nonlinear model of damping force was obtained.The test results show that the composite buffer with EPMWM and viscous fluid can absorb the impact energy from the recoil movement effectively,and provide a new method for the buffer design of weapon equipment(such as artillery,mortar,etc.).
基金financially supported by the National Key Research and Development Program of China(2022YFB3404201)the Major Science and Technology Project of Changchun City,Jilin Province(Grant No.20210301024GX)。
文摘The effect of slow shot speed on externally solidified crystal(ESC),porosity and tensile property in a newly developed high-pressure die-cast Al-Si alloy was investigated by optical microscopy(OM),scanning electron microscopy(SEM)and laboratory computed tomography(CT).Results showed that the newly developed AlSi9MnMoV alloy exhibited improved mechanical properties when compared to the AlSi10MnMg alloy.The AlSi9MnMoV alloy,which was designed with trace multicomponent additions,displays a notable grain refining effect in comparison to the AlSi10MnMg alloy.Refining elements Ti,Zr,V,Nb,B promote heterogeneous nucleation and reduce the grain size of primaryα-Al.At a lower slow shot speed,the large ESCs are easier to form and gather,developing into the dendrite net and net-shrinkage.With an increase in slow shot speed,the size and number of ESCs and porosities significantly reduce.In addition,the distribution of ESCs is more dispersed and the net-shrinkage disappears.The tensile property is greatly improved by adopting a higher slow shot speed.The ultimate tensile strength is enhanced from 260.31 MPa to 290.31 MPa(increased by 11.52%),and the elongation is enhanced from 3.72%to 6.34%(increased by 70.52%).
基金funded by a project entitled exploration field evaluation and target optimization of key basins in Chad and Niger(No.2019D-4308)initiated by the scientific research and technology development project of china national petroleum corporation.
文摘Recently,exploration breakthroughs have been made in the Lower Cretaceous sandstone reservoirs in the Doseo Basin,but the identification of reservoir fluid property is difficult due to variable reservoir lithology,complex oil-water contact within and faint responses of the oil zone,which causes the lower accuracy of reservoir fluid property identification with conventional mudlogging and wirelogging techniques.Applying the geochemical logging,fluorescent logging,mud logging and cutting logging technology,in combination with formation test data,this paper distinguishes the crude oil types,analyzes the logging response characteristics of oil zone after water washing,and establishes the interpretation charts and parameter standards for reservoir fluid properties.The crude oil can be divided into two types,namely viscous-heavy and thin-light,based on total hydrocarbon content and component concentration tested by mud logging,features of pyrolysis gas chromatogram and fluorescence spectroscopy.The general characteristics of oil layers experienced water washing include the decrease of total hydrocarbon content and component concentration from mud logging,the decrease of S1 and PS values from geochemical logging,the decrease of hydrocarbon abundance and absence of some light components in pyrolysis gas chromatogram,and the decrease of fluorescence area and intensity from fluorescence logging.According to crude oil types,the cross plots of S1 versus peak-baseline ratio,and the cross plots of rock wettability versus fluorescence area ratio are drawn and used to interpret reservoir fluid property.Meanwhile,the standards of reservoir fluid parameter are established combining with the parameters of PS and the parameters in above charts,and comprehensive multiparameter correlation in both vertical and horizontal ways is also performed to interpret reservoir fluid property.The application in the Doseo Basin achieved great success,improving interpretation ability of fluid property in the reservoir with complex oil-water contact,and also provided technical reference for the efficient exploration and development of similar reservoirs.
文摘Reservoirs provide a variety of services with economic values across multiple sectors. As demands for reservoir services continue to grow and precipitation patterns evolve, it becomes ever more important to consider the integrated suite of values and tradeoffs that attend changes in water uses and availability. Section 316 (b) of the Clean Water Act requires that owners of certain water cooled power plants evaluate technologies and operational measures that can reduce their impacts to aquatic organisms. The studies must discuss the social costs and benefits of alternative technologies including cooling towers (79 Fed. Reg. 158, 48300 - 48439). Cooling towers achieve their effect through evaporation. This manuscript estimates the property value, recreation, and hydroelectric generation impacts that could result from the evaporative water loss associated with installing cooling towers at the McGuire Nuclear Generating Station (McGuire) located on Lake Norman, North Carolina. Although this study specifically evaluates the effects of evaporative water loss from cooling towers, its methods are applicable to estimating the economic benefits and costs of a new water user or reduced water input in any complex reservoir system that supports steam electric generation, hydroelectric generation, residential properties, recreation, irrigation, and municipal water use.
基金supported by Zhejiang Provincial Science and Technology Plan Project(Grant No.2022C01118).
文摘Double-layer structure of seal coating which consisted of a Ni5Al bond coating and a Ni25 graphite top coating were prepared on steel substrate of gas turbine compressor cylinder block.Bond coating was prepared by atmospheric plasma spraying and top coating was prepared by flame spraying.The microstructure,mechanical properties and abradability of the coating were characterized by scanning elec-tron microscope(SEM),hardness tester,universal testing machine,thermal shock testing machine and abradability testing machine.The res-ults show that the overall spraying structure of the seal coating is uniform,the nickel metal phase is the skeleton supporting the entire coat-ing,and the coating is well bonded without separation.The seal coating has a bonding strength of not less than 7.7 MPa,excellent thermal stability,and thermal shock resistance cycle numbers at 500℃more than 50;the scratch length,deepest invasion depth and wear amount of the coating increase with rise of test temperature,with almost no coating adhesion,indicating that the seal coating has excellent abradability.
文摘The main obstacle to the open sharing of scientific data is the lack of a legal protection system for intellectual property.This article analyzes the progress of research papers on intellectual property in scientific data in China through literature search and statistics.Currently,research subjects are unbalanced,research content is uneven,research methods are intellectual single,and research depth is insufficient.It is recommended that different stakeholders engage in deep cross disciplinary cooperation,further improve China’s legal and policy protection system for scientific data intellectual property,and promote the open sharing of scientific data.
基金Supported by National Natural Science Foundation of China(41771565)Henan Provincial Government Decision-Making Research Bidding Project(2017B189).
文摘In the reform process of the rural land property rights system,the incentive mechanism of the rural land property rights system has a crucial impact on the production activities of rural economic entities.Due to the different rights structures of the property rights system in different social and economic development stages,the land rights and interests enjoyed by rural economic subjects are different,and the degree of incentives for farmers is also different.This difference in incentives affects farmers investment in agricultural production factors,which in turn affects agricultural performance.This paper analyzes the incentive impacts of the structure of rural land property rights on the changes of farmers land rights and agricultural performance since the founding of the People s Republic of China,in order to further deepen the reform of the land system,protect the rights and interests of farmers,promote the modernization of agriculture and rural areas,and explore the realization form and operation mechanism of the rural collective land system in the new era.
基金supported by National Natural Science Foundation of China(12071018)Fundamental Research Funds for the Central Universitiessupported by the National Research Foundation of Korea(NRF)funded by the Korea government(MIST)(2020R1F1A1A01051370)。
文摘In this paper,we define a generalized Lipschitz shadowing property for flows and prove that a flowΦgenerated by a C1vector field X on a closed Riemannian manifold M has this generalized Lipschitz shadowing property if and only if it is structurally stable.
基金Supported by Youth Project of National Social Science Fund of China(22CMZ015)。
文摘The development of diversified foods such as melons under the big food concept can reduce the pressure on staple food grain.Xinjiang has the advantages of building a new development pattern of dual circulation of diversified food industry and establishing a national diversified food safety and high-quality assurance center.The construction of an agricultural power needs the strategic support of an intellectual property power.This paper introduced and studied Xinjiang s melon industry and its agricultural intellectual property resources,analyzed the six main problems,including many idle land resources have not been developed into melon fields and the role of melons in diversified food supply systems not well played.Finally,it proposed to vigorously develop diversified food industries such as melons in Xinjiang and establish an eight-point strategy such as national diversified food safety and high-quality assurance center.
基金financially supported by the National Key R&D Program of China (No.2021YFA1200203)the National Natural Science Foundation of China (Nos.51922026 and 51975111)+1 种基金the Fundamental Research Funds for the Central Universities (No.N2202015,N2002005,and N2105001)the 111 Project of China (No.BP0719037 and B20029)。
文摘Face-centered cubic (f.c.c.) high entropy alloys (HEAs) are attracting more and more attention owing to their excellent strength and ductility synergy, irradiation resistance, etc. However, the yield strength of f.c.c. HEAs is generally low, significantly limiting their practical applications. Recently, the alloying of W has been evidenced to be able to remarkably improve the mechanical properties of f.c.c. HEAs and is becoming a hot topic in the community of HEAs. To date, when W is introduced, multiple strengthening mechanisms, including solid-solution strengthening, precipitation strengthening (μphase,σphase, and b.c.c. phase), and grain-refinement strengthening, have been discovered to be activated or enhanced. Apart from mechanical properties, the addition of W improves corrosion resistance as W helps to form a dense WO_(3) film on the alloy surface. Until now, despite the extensive studies in the literature, there is no available review paper focusing on the W doping of the f.c.c. HEAs. In that context, the effects of W doping on f.c.c. HEAs were reviewed in this work from three aspects, i.e., microstructure,mechanical property, and corrosion resistance. We expect this work can advance the application of the W alloying strategy in the f.c.c. HEAs.
基金Supported by Youth Program of National Social Science Foundation of China(22CMZ015)。
文摘Rape is the third largest oil crop in the world and the first one in China.The national average rapeseed yield is only 2077.5 kg/hm^(2),and the rapeseed oil yield is 894 kg/hm^(2).This paper introduced the main types,germplasm resources,breeding bases and breeding progress of Chinese rape,and studied its high-quality varieties,breeding patents and new varieties of agricultural plants.We analyzed the main problems such as serious loss of germplasm resources in Brassica campestris L.and Brassica juncea(L.)Czern.et Coss and weak"agricultural chip"in rape field,and put forward strategies such as strengthening the protection of rape germplasm resources,encouraging the development of"agricultural chip"in rape industry clusters with national advantages and characteristics,and strengthening the protection of agricultural intellectual property rights.
基金supported by National Natural Science Foundation of China(No.52103361)Shaanxi University Youth Outstanding Talents Support Plan,Scientific and Technological Plan Project of Xi’an Beilin District(No.GX2143)。
文摘Porous carbon(PC)is a promising electromagnetic(EM)wave absorbing material thanks to its light weight,large specific surface area as well as good dissipating capacity.To further improve its microwave absorbing performance,silver coated porous carbon(Ag@PC)is synthesized by one-step hydro-thermal synthesis process making use of fir as a biomass formwork.Phase compositions,morphological structure,and microwave absorption capability of the Ag@PC has been explored.Research results show that the metallic Ag was successfully reduced and the particles are evenly distributed inward the pores of the carbon formwork,which accelerates graphitization process of the amorphous carbon.The Ag@PC composite without adding polyvinyl pyrrolidone(PVP)exhibits higher dielectric constant and better EM wave dissipating capability.This is because the larger particles of Ag give rise to higher electric conductivity.After combing with frequency selective surface(FSS),the EM wave absorbing performance is further improved and the frequency region below-10 d B is located in8.20-11.75 GHz,and the minimal reflection loss value is-22.5 dB.This work indicates that incorporating metallic Ag particles and FSS provides a valid way to strengthen EM wave absorbing capacity of PC material.
基金Supported by Special Soft Science Research Project for Hubei Province Science and Technology Innovation Talents and Services (2022EDA060).
文摘Only by improving the production capacity of domestic herbal edible oil can China ensure the safety of the supply chain of the important industrial chain of vegetable edible oil in China and practice the big food concept.In addition to rice,maize,and soybean for using as grain and oil,there are eight kinds of herbaceous edible oil crops in Hubei Province,including rape,peanut,sesame,sunflower,perilla(perilla seed),cotton,linen and tiger nut(Cyperus esculentus).This paper studies the main industries of herbaceous edible oil crops and their intellectual property resources in Hubei Province,and analyzes the main problems of its inheritance,innovation and high-quality development under the strategy of strengthening the country with intellectual property.Finally,it proposes the countermeasures of carrying forward and inheriting traditional knowledge and traditional culture,maintaining the biodiversity of crops,strengthening the creation of new plant varieties and breeding patents,and opening up the whole chain of intellectual property rights.
基金Supported by Special Soft Science Research Project for Hubei Province Science and Technology Innovation Talents and Services(2022EDA060).
文摘Only by developing woody edible oilseeds industry can we ensure the safety of the important industrial chain and supply chain of vegetable edible oil in China.There are 13 kinds of woody edible oil plants in Hubei,including Camellia oleifera Abel(oil tea),Juglans regia L.(walnut),Olea europaea L.(olive)and Paeonia suffruticosa(oil peony).This paper studies the main industries of woody edible oilseeds in Hubei Province and their intellectual property resources,and analyzes the main problems in their intellectual property protection,inheritance,innovation and development.Finally,it proposes some strategies,including carrying forward the traditional knowledge related to woody edible oilseeds,innovating the"agricultural chip",creating key counties of national woody edible oil seeds,and developing industrial clusters with national advantages and characteristics.
基金financial supports from the National Natural Science Foundation of China (No. 51875062)China Postdoctoral Science Foundation (No. 2021M700567)。
文摘In this study,HEA/AI composite interlayer was used to fabricate Ti/Mg bimetal composites by solidliquid compound casting process.The Al layer was prepared on the surface of TC4 alloy by hot dipping,and the FeCoNiCr HEA layer was prepared by magnetron sputtering onto the Al layer.The influence of the HEA layer thickness and pouring temperature on interface evolution was investigated based on SEM observation and thermodynamic analysis.Results indicate that the sluggish diffusion effect of HEA can effectively inhibit the interfacial diffusion between Al and Mg,which is conducive to the formation of solid solution,especially when the thickness of HEA is 800 nm.With the increase of casting temperature from 720 ℃ to 730 ℃,740℃,and 750 ℃,α-Al(Mg),α-Al(Mg)+Al3Mg2,Al3Mg2+Al12Mg17,and Al12Mg17+δ-Mg are formed at the interface of Ti/Mg bimetal,respectively.When the thickness of the HEA layer is 800 nm and the pouring temperature is 720 ℃,the bonding strength of the Ti/Mg bimetal can reach the maximum of 93.6 MPa.
基金Youth Project of National Social Science Fund of China(22CMZ015).
文摘This paper introduced the grape industry in Xinjiang and its agricultural intellectual property resources,and analyzed six major problems such as the ineffective leading role of intellectual property rights in high-quality development.Finally,it proposed eight strategies to build a national-level regional fine-grain breeding base for grapes and develop“agricultural chips”in the context of the strategy of strengthening the country with intellectual property and innovation-driven development strategy.
基金Supported by Youth Project of National Social Science Fund of China(22CMZ015)。
文摘"Three new developments"is the guiding ideology of Chinese-style high-quality development in the new era.Jujube(Zizyphus jujube Mill.)is a plant of Zizyphus of Rhamnaceae,which originated in China and has been listed as one of the"five fruits"since ancient times.Xinjiang is the most important jujube producing area in China,and its yield has accounted for 50%of the national jujube yield.In the five prefectures and cities of southern Xinjiang,as well as the regimental farms of southern and eastern Xinjiang of Xinjiang Production and Construction Corps,the jujube industry is an advantageous characteristic industry in agriculture.This paper studied Xinjiang jujube industry and its agricultural intellectual property resources,analyzed six major issues to be further implemented,such as the"three new developments"thinking and the strategy of building an intellectual property power,and puts forward eight strategies such as coordinating the two markets and two resources to accelerate the construction of a new development pattern and dual circulation of jujube.
基金Financial support comes from China National Natural Science Foundation(No.51974352)as well as from China University of Petroleum(East China)(No.2018000025 and No.2019000011).
文摘A comprehensive experimental program has been performed to characterize the hydration and engineering property evolution of a class G oil well cement under various curing temperatures from 30 to 90℃.The progress of hydration was monitored by isothermal calorimetry(atmospheric pressure);the viscosity evolution was measured using a high temperature and high pressure consistometer(up to 200 MPa);the ultrasonic property development was evaluated by an ultrasonic cement analyzer(up to 100 MPa).Test results indicate that the influences of curing temperature and pressure on the hydration,viscosity and ultrasonic property development can be modeled by a scale factor method that is similar to the maturity method used in the concrete industry.However,the key parameters of the scale factor model,namely the apparent activation energy and the apparent activation volume of cement showed obvious variations with test method and curing condition.The test results indicate that the curing temperature has a stronger effect on cement hydration rate than viscosity and ultrasonic property development rate,while the curing pressure has a much stronger influence on cement slurry properties before setting(viscosity)than after setting(ultrasonic property).