Life-Cycle Bearing Capacity for Pre-Stressed T-beams Based on Full-Scale Destructive Test

To investigate the evolution of load-bearing characteristics of pre-stressed beams throughout their service life and to provide a basis for accurately assessing the actual working state of damaged pre-stressed concrete T-beams,destructive tests were conducted on full-scale pre-stressed concrete beams.Based on the measurement and ana-lysis of beam deflection,strain,and crack development under various loading levels during the research tests,combined with the verification coefficient indicators specified in the codes,the verification coefficients of bridges at different stages of damage can be examined.The results indicate that the T-beams experience complete,incom-plete linear,and non-linear stages during the destructive test process.In the complete linear elastic stage,both the deflection and bottom strain verification coefficients comply with the specifications,indicating a good structural load-bearing capacity no longer adheres to the code’s requirements.In the non-linear stage,both coefficients exhi-bit a sharp increase,resulting in a further decrease in the structure’s load-bearing capacity.According to the pro-visions of the current code,the beam can be in the incomplete linear stage when both values fall within the code’s specified range.The strain verification coefficient sourced from the compression zone at the bottom of theflange is not recommended for assessing the bridge’s load-bearing capacity.

Test system for miniature pulse-powered photoelectric invert switch based on CPLD

For electronic piezo gauge used for testing gun chamber pressure, its internal miniature pulse-powered photoelectric invert switch cannot often be powered up normally. To solve this problem, a test system for invert switch is presented to verify the reliability of the invert switch. The test system uses complex programmable logic device （CPLD） to control data acquisition of A/D converter and data storage of external flash memory, and then transmits the acquired data to a computer for data analysis and processing. The test system can provide the required sampling frequency of the signal in high temperature, normal temperature and low temperature environments, and the reliability of the invert switch can be verified according to the signal parameters. The results show that the test system has high precision and the tested invert switch has low power consumption and high reliability.

Pulsed Eddy Current Non-destructive Testing and Evaluation:A Review

Pulsed eddy current （PEC） non-destructive test- ing and evaluation （NDT＆E） has been around for some time and it is still attracting extensive attention from researchers around the globe, which can be witnessed through the reports reviewed in this paper. Thanks to its richness of spectral components, various applications of this technique have been proposed and reported in the lit- erature covering both structural integrity inspection and material characterization in various industrial sectors. To support its development and for better understanding of the phenomena around the transient induced eddy currents, attempts for its modelling both analytically and numeri- cally have been made by researchers around the world. This review is an attempt to capture the state-of-the-art development and applications of PEC, especially in the last 15 years and it is not intended to be exhaustive. Future challenges and opportunities for PEC NDT＆E are also presented.

Fast Remaining Capacity Estimation for Lithium-ion Batteries Based on Short-time Pulse Test and Gaussian Process Regression

It remains challenging to effectively estimate the remaining capacity of the secondary lithium-ion batteries that have been widely adopted for consumer electronics,energy storage,and electric vehicles.Herein,by integrating regular real-time current short pulse tests with data-driven Gaussian process regression algorithm,an efficient battery estimation has been successfully developed and validated for batteries with capacity ranging from 100%of the state of health(SOH)to below 50%,reaching an average accuracy as high as 95%.Interestingly,the proposed pulse test strategy for battery capacity measurement could reduce test time by more than 80%compared with regular long charge/discharge tests.The short-term features of the current pulse test were selected for an optimal training process.Data at different voltage stages and state of charge(SOC)are collected and explored to find the most suitable estimation model.In particular,we explore the validity of five different machine-learning methods for estimating capacity driven by pulse features,whereas Gaussian process regression with Matern kernel performs the best,providing guidance for future exploration.The new strategy of combining short pulse tests with machine-learning algorithms could further open window for efficiently forecasting lithium-ion battery remaining capacity.

基于PULSE Labshop的双通道测量航空噪声方法研究

根据《航空器型号和适航合格审定噪声规定》(CCAR-36)中噪声测量规范,使用PULSE Labshop噪声振动测量仪进行双通道法测量航空噪声。针对PLUSE系统从硬件、软件2个方面进行了研究和分析,可为后续的多通道测量振动、噪声的各项测试提供基础性的理论帮助。同时,双通道法测量航空噪声实现了试验的冗余设计,一定程度上可提高试验的准确性。

Properties and testing of a hydraulic pulse jet and its application in offshore drilling

Offshore drilling has attracted more attention than ever before due to the increasing worldwide energy demand especially in China. High cost, long drilling cycles, and low rate of penetration （ROP） represent critical challenges for offshore drilling operations. The hydraulic pulse generator was specifically designed, based on China offshore drilling technologies and parameters, to overcome problems encountered during offshore drilling. Both laboratory and field tests were conducted to collect the characteristics of the hydraulic pulse generator. The relationships between flow rate and pressure amplitude, pressure loss and pulse frequency were obtained, which can be used to optimize operation parameters for hydraulic pulse jet drilling. Meanwhile a bottom hole assembly （BHA） for pulse jet drilling has been designed, combining the hydraulic pulse generator with the conventional BHA, positive displacement motor, and rotary steerable system （RSS） etc. Furthermore, the hydraulic pulse jet technique has been successfully applied in more than 10 offshore wells in China. The depth of the applied wells ranged from 2,000 m to 4,100 m with drilling bit diameters of 311 mm and 216 mm. The field application results showed that hydraulic pulse jet technique was feasible for various bit types and formations, and that ROP could be significantly increased, by more than 25%.

Effect of Electromagnetic Pulse Exposure on Permeability of Blood-testicle Barrier in Mice

Objective To study the effect of electromagnetic pulse （EMP） exposure on the permeability of blood-testicle barrier （BTB） in mice. Methods Adult male BALB/c mice were exposed to EMP at 200 kV/m for 200 pulses with 2 seconds interval. The mice were injected with 2% Evans Blue solution through caudal vein at different time points after exposure, and the permeability of BTB was monitored using a fluorescence microscope. The testis sample for the transmission electron microscopy was prepared at 2 h after EMP exposure. The permeability of BTB in mice was observed by using Evans Blue tracer and lanthanum nitrate tracer. Results After exposure, cloudy Evans Blue was found in the testicle convoluted seminiferous tubule of mice. Lanthanum nitrate was observed not only between testicle spermatogonia near seminiferous tubule wall and sertoli cells, but also between sertoli cells and primary spermatocyte or secondary spermatocyte. In contrast, lanthanum nitrate in control group was only found in the testicle sertoli cells between seminiferous tubule and near seminifdrous tubule wall. Conclusion EMP exposure could increase the permeability of BTB in the mice.

Pulse wave Doppler ultrasound of testicular arteries and their relationship with semen characteristics in healthy bulls

Background: Semen evaluation is used to estimate the testicular function. In bulls, the spermatozoa present in the ejaculate are the result of a process that begun more than 2 mo earlier, bequeathing a delayed depiction of the actual function of the testis. Since testis vascularization might be critical for the gonad function, selected pulse wave Doppler ultrasound parameters were assessed in this study, for instance the peak systolic velocity, the end diastolic velocity and the resistive index of the testicular artery along the spermatic cord, the marginal portion of the testicular artery and the intratesticular branches of the testicular artery both in healthy adult and young bulls.Correlations between these parameters and characteristics of semen that was collected numerous times, before and after the Doppler ultrasound examination.Results: The peak systolic velocity and the end diastolic velocity measured in the testicular artery along the spermatic cord(supratesticular artery – SA) were variable among the bulls and within individual bulls, likely due to the convoluted course of the vessel. The resistive index was found highly repeatable in the same bull. A reduction in the resistive index was found between the supratesticular artery and the marginal portion of the testicular artery(P < 0.01), and between the marginal portion of the testicular artery and the intratesticular branches of the testicular artery(P < 0.05). No differences were recorded for the pulse wave Doppler ultrasound parameters in young bulls compared with adults. A significant correlation was found between the resistive index of the marginal portion of the testicular artery and total sperm in the ejaculate(r = 0.516, P < 0.05), the immature sperm(r = 0.462, P < 0.05), the teratoid sperm(r = 0.375, P < 0.05), and the "Dag defect" sperm(r = 0.389, P < 0.05). Similarly, the resistive index of the intratesticular branches of the testicular artery were found correlated with the total sperm number in the ejaculate(r = 0.568, P < 0.05), the immature sperm(r = 0.523, P < 0.05), the teratoid sperm(r = 0.418, P < 0.05), and the "Dag defect" sperm(r = 0.341, P < 0.05).Conclusions: The data presented in this study suggest that the resistive index, measured at the marginal portion of the testicular artery, could be an easy-to-perform parameter to evaluate the spermatogenesis quality in young bulls and normal adults.

Video head impulse test (vHIT) in migraine dizziness

Background and objective: Migraine is an extremely prevalent primary headache disorder that frequently associates parallel symptoms such as dizziness, tinnitus and hearing loss. Our aim is to investigate differences in video head impulse (vHIT) results with patients suffering from vestibular migraine (VM) and healthy people, taking into consideration mean values of vestibule ocular reflex (VOR) gain, occurrence of the compensatory saccades latency and amplitude. According to the results, determine the usefulness of vHIT in vestibular migraine diagnostics. Methods: A total number of 120 subjects were enrolled in the study, 80 of them were vestibular migraine patients (VM), while the other 40 were a control group of age matched healthy subjects. History was taking during the evaluation; videonystagmography and the video head impulse test were done.Results: The rate of saccades is much more higher in the VM group compared to the healthy subjects group, only 7.5% of the VM group showed a low VOR gain with compensatory saccades denoting a vestibular deficit. Conclusion: The refixation saccades are an important sign that could underlie different vestibular problems. vHIT result can contribute to the completion of full mosaic of vestibular migraine diagnostics. ? 2018 PLA General Hospital Department of Otolaryngology Head and Neck Surgery. Production and hosting by Elsevier(Singapore) Pte Ltd. This is an open access article under the CC BY-NC-ND license http://creativecommons.org/licenses/by-nc-nd/4.0/).

A possible objective test to detect benign paroxysmal positional vertigo. The role of the caloric and video-head impulse tests in the diagnosis

Background:Benign paroxysmal positional vertigo(BPPV)is characterized by vertigo lasting from seconds to minutes,induced by head movements.Objectives:Our study aimed to investigate the clinical significance of the caloric vestibular and video head-impulse tests(vHIT)diagnosing the disorder.Methods:68 patients suffering from posterior canal BPPV(25 male,43 females,mean age±SD,54.5±13.2 years)and 56 patients with a normal functioning vestibular system as control were investigated.Bithermal caloric test and vHIT was performed during the same medical check-up.Canal paresis(CP%),gain(GA)and asymmetry(GA%)parameters were calculated.Results:The Dix-Hallpike manoeuvre was only positive in 4%of this population.The CP%parameter was only pathologic in two patients,and there was no significant difference between control and BPPV patients(p=0.76).The GA value was never under 0.8 in this population,but GA%was abnormal in 63.2%.A significant difference comparing the GA%values to the control group was seen(p=0.034).There was no correlation detected between the CP%and GA%values in BPPV.Regarding the GA%value,61%sensitivity and 76%specificity was seen.Conclusion:The Dix-Hallpike manoeuvre was not often positive in the non-acute phase of BPPV;therefore,objective testing is essential.The caloric test does not have clinical significance in BPPV,but vHIT can be helpful based on the GA%parameter。

Life test research of a high specific impulse Hall thruster HEP-140MF

In this study,a high specific impulse Hall thruster,HEP-140 MF,having a high discharge voltage,was used to accelerate ions.We aimed to obtain a high specific impulse and an acceleration zone moving downstream toward the channel exit to reduce wall sputtering erosion of the walls of the discharge channel,hence ensuring an enhanced lifetime.To study the lifetime characteristics of the high specific impulse Hall thruster,a life test was performed on the HEP-140 MF thruster for the first time,and performance parameters,such as thrust,specific impulse,and efficiency,were measured.Changes in the performance parameters and evolutions in the surface profiles of the discharge channel wall were summarized.The reasons contributing to these changes during the life test were analyzed.Moreover,the accelerated life test method was validated on the HEP-140 MF.

Heating pulse tests under constant volume on Boom clay

Boom clay formation is a potential natural host rock for geological disposal of high-level nuclear waste in Belgium.Heating pulse tests with controlled power supply（maximum temperature was limited to 85℃） and controlled hydraulic boundary conditions were performed under nearly constant volume conditions to study the impact of thermal loading on the clay formation.Selected test results of intact borehole samples retrieved in horizontal direction are presented and discussed.The study focuses on the time evolution of temperature and pore water pressure changes along heating and cooling paths,i.e.pore pressure build-up during quasi-undrained heating and later dissipation at constant temperature.

Saccades of video head impulse test in Meniere's disease and Vestibular Migraine: What can we learn from?

Background:Saccades are often observed on video head impulse tests(vHIT)in patients with Meniere's Disease(MD)and Vestibular Migraine(VM).However,their saccadic features are not fully described.Objective:This study aims to identify the saccades characteristics of MD and VM.Methods:75 VM patients and 103 definite unilateral MD patients were enrolled in this study.First raw saccades were exported and analyzed.The VM patients were divided into left and right based on their ears,while the MD patients were separated into affected and unaffected subgroups based on their audiograms and symptoms.Results:The MD patients have more saccades on the affected side(85%vs.69%),and saccade velocity is more consistent than the contralateral side(shown by the coefficient of variation).The saccades occurrence rates on both sides are similar in VM(77%vs.76%),as are other saccadic parameters.The MD patients have more significant inter-aural differences than the VM patients,manifested in higher velocity(p-value 0.000),earlier arriving(p-value 0.010),and more time-domain gathered(p-value 0.003)on the affected side.Conclusions:Bilateral saccades are commonly observed in MD and VM.In contrast to MD,saccades on VM are subtle,scattered,and late-arrived.Furthermore,the MD patients showed inconsistent saccadic distribution with more velocity-uniform saccades on the affected side.

Research on Strong Pulsed Electromagnetic Field Test Method by Time-frequency Combination

Many conventional methods of testing strong and pulsed electromagnetic fields,the ones used in radars for example,had deficiencies due to the difficulty in obtaining simultaneous information about the electromagnetic field's peak both in the time domain and in the frequency domain.With regard to this problem,after analyzing the time-domain and the frequency-domain characteristics of radar pulsed signals,we propose a new time-frequency combination test method based on the correction of the test parameters,as well as its correction method at different bandwidths.The test method is applied in a quick test of a high-power pulsed radar signal,and the corrected results have error less than 1 dB in both the time domain and the frequency domain,which indicates that the proposed time-frequency combined method is effective in testing strong and pulsed electromagnetic fields.

Analysis of video head impulse test saccades data in patients with vestibular migraine or probable vestibular migraine

Objective:Saccades accompanied by normal gain in video head impulse tests(vHIT)are often observed in patients with vestibular migraine(VM).However,they are not considered as an independent indicator,reducing their utility in diagnosing VM.To better understand clinical features of VM,it is necessary to understand raw saccades data.Methods:Fourteen patients with confirmed VM,45 patients with probable VM(p-VM)and 14 agematched healthy volunteers were included in this study.Clinical findings related to spontaneous nystagmus(SN),positional nystagmus(PN),head-shaking nystagmus(HSN),caloric test and vHIT were recorded.Raw saccades data were exported and numbered by their sequences,and their features analyzed.Results:VM patients showed no SN,PN or HSN,and less than half of them showed unilateral weakness(UW)on caloric test.The first saccades from lateral semicircular canal stimulation were the most predominant for both left and right sides.Neither velocity nor time parameters were significantly different when compared between the two sides.Most VM patients(86%)exhibited small saccades,around 35%of the head peak velocity,with a latency of 200e400 ms.Characteristics of saccades were similar in patients with p-VM.Only four normal subjects showed saccades,all unilateral and seemingly random.Conclusions:Small saccades involving bilateral semicircular canals with a scattered distribution pattern are common in patients with VM and p-VM.

昆明烟区土壤线虫数量与环境因子的Mantel Test分析

为进一步明确昆明烟区影响线虫的环境因素,于2022年采集云南昆明烟区8个县(市、区)64个乡镇的320个植烟土壤样品,调查与测定样品采集地的海拔、土壤线虫数量以及土壤理化性质(pH值及有机质、水解性氮、速效钾和有效磷含量),并探讨土壤线虫数量与植烟土壤环境因子之间的潜在关系。结果表明,昆明烟区土壤线虫数量一定程度上受到海拔及土壤理化性质的影响,海拔与有机质、水解性氮和速效钾呈显著正相关,pH值与有效磷呈极显著负相关,相关系数为-0.850;土壤线虫数量与土壤有效磷呈正相关,与海拔、pH值、有机质、水解性氮、速效钾呈负相关,其中与海拔、有机质和水解性氮的相关系数较大,分别为-0.751、-0.651和-0.568。通过Mantel test分析确定海拔、有机质和水解性氮含量是影响昆明烟区土壤线虫数量的重要因子。本结果可为有效防治土壤线虫提供科学依据。

Pulse Electrodeposition and Nanoindentation Test of ZrO_2/Ni Nanocomposite

ZrO2/Ni nanocomposite was produced via pulse electrodeposition using a nickel sulfmate bath. The effects of main factors including pH value, temperature T, current density Dk and ZrO2 content p on the electrodeposit were dealt with by the Taguchi method. Experimental results show that the current density and ZrO2 content affect the electrodepositing process significantly. Nanocomposite with an average grain size of about 50 nm and ZrO2 content of up to 0.4 wt% was produced under the optimal condition. The Young＇s modulus of the achieved composite is similar to that of polycrystalline Ni. The microhardness is much higher than that of common pure Ni, primarily due to the ultrafine grains of Ni matrix by the Hall-Petch mechanism. The homogeneous dispersion of stiff ZrO2 particles in the Ni matrix acting as dislocation pinning and microcrack pinning also results in the strengthening effect.

The Effects of Electromagnetic Pulse on the Protein Levels of Tight Junction Associated-Proteins in the Cerebral Cortex,Hippocampus,Heart,Lung,and Testis of Rats

Objective To investigate changes in the expression of tight junction （TJ） proteins in the cerebral cortex,hippocampus,heart,lung,and testes of rats after exposure to electromagnetic pulse （EMP）.Methods Eighteen adult male Sprague-Dawley rats were divided into sham and exposure groups.The exposure groups received EMP at 200 kV/m for 200 pulses with a repetition rate of 1 Hz.The expression of TJ proteins （ZO-1,occludin,actin） in the several organs was examined by western blotting.Results ZO-1 levels in the cerebral cortex decreased 1 h and 3 h after EMP exposure compared with sham group （P0.05）.No significant difference was observed for occludin and actin.ZO-1 levels in the hippocampus increased 1 h and 3 h post-exposure （P0.05）,and occludin decreased after 3 h （P0.05）;however,actin was unaffected.ZO-1 levels in the heart increased 3 h post-exposure （P0.05）,occludin decreased 3 h post-exposure （P0.05）,and actin increased 1 h and 3 h post-exposure （P0.05）.ZO-1,occludin and actin levels in the lung decreased compared with those in the sham group （P0.05）.ZO-1 and occludin levels in the testes decreased 1 h and 3 h post-exposure （P0.05）,but actin showed no significant change.Conclusion Exposure to EMP altered the expression levels of TJ proteins,particularly ZO-1,in the organs of adult male rats,which may induce changes in barrier structure and function.

Failure characterization of fully grouted rock bolts under triaxial testing

Confining stresses serve as a pivotal determinant in shaping the behavior of grouted rock bolts.Nonetheless,prior investigations have oversimplified the three-dimensional stress state,primarily assuming hydrostatic stress conditions.Under these conditions,it is assumed that the intermediate principal stress(σ_(2))equals the minimum principal stress(σ_(3)).This assumption overlooks the potential variations in magnitudes of in situ stress conditions along all three directions near an underground opening where a rock bolt is installed.In this study,a series of push tests was meticulously conducted under triaxial conditions.These tests involved applying non-uniform confining stresses(σ_(2)≠σ_(3))to cubic specimens,aiming to unveil the previously overlooked influence of intermediate principal stresses on the strength properties of rock bolts.The results show that as the confining stresses increase from zero to higher levels,the pre-failure behavior changes from linear to nonlinear forms,resulting in an increase in initial stiffness from 2.08 kN/mm to 32.51 kN/mm.The load-displacement curves further illuminate distinct post-failure behavior at elevated levels of confining stresses,characterized by enhanced stiffness.Notably,the peak load capacity ranged from 27.9 kN to 46.5 kN as confining stresses advanced from σ_(2)=σ_(3)=0 to σ_(2)=20 MPa and σ_(3)=10 MPa.Additionally,the outcomes highlight an influence of confining stress on the lateral deformation of samples.Lower levels of confinement prompt overall dilation in lateral deformation,while higher confinements maintain a state of shrinkage.Furthermore,diverse failure modes have been identified,intricately tied to the arrangement of confining stresses.Lower confinements tend to induce a splitting mode of failure,whereas higher loads bring about a shift towards a pure interfacial shear-off and shear-crushed failure mechanism.

Pulse rate estimation based on facial videos:an evaluation and optimization of the classical methods using both self-constructed and public datasets

Pulse rate is one of the important characteristics of traditional Chinese medicine pulse diagnosis,and it is of great significance for determining the nature of cold and heat in diseases.The prediction of pulse rate based on facial video is an exciting research field for getting palpation information by observation diagnosis.However,most studies focus on optimizing the algorithm based on a small sample of participants without systematically investigating multiple influencing factors.A total of 209 participants and 2,435 facial videos,based on our self-constructed Multi-Scene Sign Dataset and the public datasets,were used to perform a multi-level and multi-factor comprehensive comparison.The effects of different datasets,blood volume pulse signal extraction algorithms,region of interests,time windows,color spaces,pulse rate calculation methods,and video recording scenes were analyzed.Furthermore,we proposed a blood volume pulse signal quality optimization strategy based on the inverse Fourier transform and an improvement strategy for pulse rate estimation based on signal-to-noise ratio threshold sliding.We found that the effects of video estimation of pulse rate in the Multi-Scene Sign Dataset and Pulse Rate Detection Dataset were better than in other datasets.Compared with Fast independent component analysis and Single Channel algorithms,chrominance-based method and plane-orthogonal-to-skin algorithms have a more vital anti-interference ability and higher robustness.The performances of the five-organs fusion area and the full-face area were better than that of single sub-regions,and the fewer motion artifacts and better lighting can improve the precision of pulse rate estimation.