Effect of Conventional and Pulsed TIG Welding on Microstructural and Mechanical Characteristics of AA 6082-T6 Repair Welds

Repair welding of AA 6082-T6 joints was carried out using ER 4043 filler through the TIG welding process with or without pulsed current.Microstructure and mechanical characteristics of the joints before and after repairing were investigated by examining macrostructure,microstructure,and distributions of porosity in the weld metal(WM),and by hardness,tensile,and bending tests.We observed that the welding current,phase transformations in heat-affected zone(HAZ)and porosity introduced in the WM during welding influence on its mechanical properties in sequence.The experimental results showed that the bead width and penetration as well as size of pores in the joints were mainly influenced by the welding currents.The sound joints were obtained at a welding current of 140 A with or without pulsed current when welding speed and gas flow rate were set at 20 cm·min-1 and 15 L·min-1,respectively.Among them,the decrease in mechanical properties of repair weld(RW)was directly related to the phase transformations in the over-ageing zone due to the double welding thermal cycles and elevated distribution of porosity in the WM.In addition,it was observed that the comparatively smaller grain size and lower porosity in WM of the RW produced by pulsed TIG welding gave a positive effect on its mechanical properties.

Optimizing the Pulsed Current Gas Tungsten Arc Welding Parameters

The selection of process parameter in the gas tungsten arc （GTA） welding of titanium alloy was presented for obtaining optimum grain size and hardness. Titanium alloy （Ti-6Al-4V） is one of the most important non-ferrous metals which offers great potential application in aerospace, biomedical and chemical industries, because of its low density （4.5 g/cm^3）, excellent corrosion resistance, high strength, attractive fracture behaviour and high melting point （1678℃）. The preferred welding process for titanium alloy is frequent GTA welding due to its comparatively easier applicability and better economy. In the case of single pass （GTA） welding of thinner section of this alloy, the pulsed current has been found beneficial due to its advantages over the conventional continuous current process. Many considerations come into the picture and one needs to carefully balance various pulse current parameters to reach an optimum combination. Four factors, five level, central composite, rotatable design matrix were used to optimize the required number of experimental conditions. Mathematical models were developed to predict the fusion zone grain size using analysis of variance （ANOVA） and regression analysis. The developed models were optimized using the traditional Hooke and Jeeve＇s algorithm. Experimental results were provided to illustrate the proposed approach.

Numerical analysis for weld pool of pulsed TIG welding

A two-dimensional axisymmetric mathematical model of weld pool of pulsed TIG welding was established. Numerical simulation for weld pool of pulsed TIG welding was done using FLUENT software by selecting the appropriate boundary conditions and strongly coupled control equations. The distributions of temperature field and flow field of weld pool under the periodic change of welding current were obtained. According to the maximum temperature of upper and lower surface of workpiece and depth and width of weld pool, the distributions of temperature field and flow field under different pulsed frequencies and current duty cycles were obtained and periodic variation was analyzed under pulsed current. The analysis results show that with the increase of pulsed frequency, weld pool width increases slightly while depth decreases slightly, and with the increase of current duty cycle, the width and depth of weld pool both increase significantly, and the depth increases greatly.

Research and engineering application of the arc welding pulsed controller technology

The tenacity of heat-affected zone （HAZ） will decline and the size of grains will increase, because of the overheating on HAZ when submerged are welding （SAW） is ased to thick plate with high heat input. The shaping will worsen when SAW is used to thin plate with high current at high speed. A new SAW technology, the pulsed direct current （DC） automatic SAW, will be put forward in this paper in order to overcome the above shortcomings. And a pulsed controller with micro-controller unit （MCU） as the core, nixie tube （NT） and keyboard as the man-machine conversation interface is developed. The main functions of the pulsed controller include the output of pulsed welding current and the working with twinwire. The research has widely prospects in application with significant meanings in theory and practical engineering.

Weld pool image sensor for pulsed MIG welding

Visual image sensor is developed to detect the weld pool images in pulsed MIG welding. An exposure controller, which is composed of the modules of the voltage transforming, the exposure parameters presetting, the complex programmable logic device （CPLD） based logic controlling, exposure signal processing, the arc state detecting, the mechanical iris driving and so on, is designed at first. Then, a visual image sensor consists of an ordinary CCD camera, optical system and exposure controller is established. The exposure synchronic control logic is described with very-high-speed integrated circuit hardware description language （VHDL） and programmed with CPLD , to detect weld pool images at the stage of base current in pulsed MIG welding. Finally, both bead on plate welding and V groove filled welding are carried out, clear and consistent weld pool images are acquired.

Modeling, Simulation and Control of Pulsed DE-GMA Welding Process for Joining of Aluminum to Steel

Joining of aluminum to steel has attracted significant attention from the welding research community,automotive and rail transportation industries.Many current welding methods have been developed and applied,however,they can not precisely control the heat input to work-piece,they are high costs,low efficiency and consist lots of complex welding devices,and the generated intermetallic compound layer in weld bead interface is thicker.A novel pulsed double electrode gas metal arc welding（Pulsed DE-GMAW）method is developed.To achieve a stable welding process for joining of aluminum to steel,a mathematical model of coupled arc is established,and a new control scheme that uses the average feedback arc voltage of main loop to adjust the wire feed speed to control coupled arc length is proposed and developed.Then,the impulse control simulation of coupled arc length,wire feed speed and wire extension is conducted to demonstrate the mathematical model and predict the stability of welding process by changing the distance of contact tip to work-piece（CTWD）.To prove the proposed PSO based PID control scheme’s feasibility,the rapid prototyping experimental system is setup and the bead-on-plate control experiments are conducted to join aluminum to steel.The impulse control simulation shows that the established model can accurately represent the variation of coupled arc length,wire feed speed and the average main arc voltage when the welding process is disturbed,and the developed controller has a faster response and adjustment,only runs about 0.1 s.The captured electric signals show the main arc voltage gradually closes to the supposed arc voltage by adjusting the wire feed speed in 0.8 s.The obtained typical current waveform demonstrates that the main current can be reduced by controlling the bypass current under maintaining a relative large total current.The control experiment proves the accuracy of proposed model and feasibility of new control scheme further.The beautiful and smooth weld beads are also obtained by this method.Pulsed DE-GMAW can thus be considered as an alternative method for low cost,high efficiency joining of aluminum to steel.

Digital pulsed MIG welding machine based on adaptive fuzzy controller

Digital pulsed metal inert gas welding machine with double closed-loop control mode is designed and implemented. It realizes precision control for real time energy and demonstrates the flexibility of digital control. Test results of design prototype show that the designed control strategy can effectively adapt to the change of arc length and achieve ideal droplet transfer via one drop per pulse mode. Thus the welding process is stable and the weld bead is good.

Effect of pulsed laser process parameters on welding quality of automobile fuel injector

In this research, pulverization plate and base of a fuel injector in an automobile electronic-controlled engine was joined by pulsed laser welding. The different welding parameters were evaluated and effect of process parameters on joint characteristics was analyzed. The optimal process parameters were obtained as follows： welding current 120 A, welding speed 600 ram/rain, pulse duration 1.80 ms and pulse frequency 60 Hz. The microstructure of weld metal was investigated. Results show that the fusion zone is austenitic dendrite, the weld center is equiaxed grain, while the transition zone between fusion zone and weld center is mixed crystal with austenitic dendrite and equiaxed grain. The weld layered phenomenon was observed, and eddy caused by keyhole effect is the main reason for the formation of layered structure in molten pool.

Analysis of droplet transfer of pulsed MIG welding based on electrical signal and high-speed photography

In order to study how welding parameters affect welding quality and droplet transfer, a synchronous acquisition and analysis system is established to acquire and analyze electrical signal and instantaneous images of droplet transfer simultaneously, which is based on a self-developed soft-switching inverter. On the one hand, welding current and voltage signals are acquired and analyzed by a self-developed dynamic wavelet analyzer. On the other hand, images are filtered and optimized after they are captured by high-speed camera. The results show that instantaneous waveforms and statistical data of electrical signal contribute to make an overall assessment of welding quality, and that optimized high-speed images allow a visual and clear observation of droplet transfer process. The analysis of both waveforms and images leads to a further research on droplet transfer mechanism and provides a basis for precise control of droplet transfer.

Digital control of pulsed gas metal arc welding inverter using TMS320LF2407A

A digital control of pulsed gas metal arc welding inverter was proposed. A control system consisting of analogue parts was replaced with a new digital control implemented in a TMS320LF2407A DSP chip. The design and constructional features of the whole digital control were presented. The resources of the DSP chip were efficiently utilized and the circuits are very concise, which can enhance the stability and reliability of welding inverter. Experimental results demonstrate that the developed digital control has the ability to accomplish the excellent pulsed gas metal arc welding process and the merits of the developed digital control are stable welding process, little spatter and perfect weld appearance.

Study on Weld Quality Characteristics of Pulsed Current Micro Plasma Arc Welding of Inconel625 Sheets

Nickel alloys had gathered wide acceptance in the fabrication of components which require high temperature resistance and corrosion resistance, such as metallic bellows used in expansion joints used in aircraft, aerospace and petroleum industry. In the present paper an attempt is made to study various weld quality characteristics like weld bead geometry dimensions, micro hardness, microstructure, grain size and tensile properties of Pulsed Current Micro Plasma Welding of Inconel625sheets. Weld joint was prepared by fusing the two parent metals of Inconel625 sheets. Square butt joint is used and welding was carried out using Pulsed DCEN, without filler wire. Peak current, back current, pulse and pulse width are considered as the main influential input variables during the welding.

MATHEMATICAL SIMULATION OF HEAT AND MASS TRANSFER IN PULSED ARC WELDING BY MELTING ELECTRODE

In this paper the processes of melting and transfer of an electrode metal to the molten pool, hydrody- namics of molten pool in controlled pulsed arc welding in carbon dioxide have been investigated.The process of pulsed arc welding with systematic short - circuits of the arc gap is realized by adaptive algo- rithms of pulsed control over main energetic parameters of welding - arc current and voltage,arc heated efficiency,peak,short - circuiting current, which provide the dosage of energy for energy for melting and transfer of every for of an electrode metal, the control over fluidity of the weld pool. Physica and mathematical models describing such processes in CO2, origind software hare been developed.The re- sults of physical simulation and mathemaical modelling permit to determine the influence of energetic parameters of the process on the condition of the 'power source-electrode-arc-molten pool' electrodynamic system at each moment of time.

Analysis of weld pool vibration characteristics in pulsed gas metal arc welding

Using highspeed camera image measuring and processing,the contour of the weld pool was extracted accurately in pulsed metal inert gas(P-MIG)welding.Based on this extraction method,time and frequency domain characteristics at different points along the contour of the weld pool were analyzed for one pulse one droplet and one pulse two droplets,respectively.The results show that,because of the wave super position that was created by the pulsed arc and droplet impacting the weld pool,the oscillation amplitude along the weld pool fluctuated and decreased with an increase in distance from the point to the arc center.The oscillation near the arc center was complex and intense for one pulse two droplets,and the amplitude were relatively small because the oscillation caused by the pulsed arc could be offset by the molten droplet impact.The weld pool oscillation that was caused by the pulsed arc was stronger than that caused by the droplet.

Study on Effect of Welding Speed on Micro Structure and Mechanical Properties of Pulsed Current Micro Plasma Arc Welded Inconel 625 Sheets

Nickel alloys had gathered wide acceptance in the fabrication of components which require high temperature resistance and corrosion resistance, such as metallic bellows used in expansion joints used in aircraft, aerospace and petroleum industry. Micro Plasma Arc Welding (MPAW) is one of the important arc welding processes commonly using in fabric- cation of Nickel alloys. In the present paper welding of Inconel 625 sheets using pulsed current micro plasma arc weld- ing was discussed. The paper mainly focuses on studying the weld quality characteristics like weld pool geometry pa- rameters, microstructure, grain size, hardness and tensile properties of Pulsed Current Micro Plasma Arc Welded In- conel 625 sheets at different welding speeds. Results reveals that at a welding speed of 260 mm/minute better weld quality characteristics can be obtained.

Pulsed current and dual pulse gas metal arc welding of grade AISI: 310S austenitic stainless steel

The transverse shrinkage, mechanical and metallurgical properties of AISI: 310 S ASS weld joints prepared by P-GMAW and DP-GMAW processes were investigated. It was observed that the use of the DP-GMAW process improves the aforementioned characteristics in comparison to that of the P-GMAW process. The enhanced quality of weld joints obtained with DP-GMAW process is primarily due to the combined effect of pulsed current and thermal pulsation(low frequency pulse). During the thermal pulsation period, there is a fluctuation of wire feed rate,which results in the further increase in welding current and the decrease in arc voltage. Because of this synchronization between welding current and arc voltage during the period of low frequency pulse, the DP-GMAW deposit introduces comparatively more thermal shock compared to the P-GMAW deposit, thereby reducing the heat input and improves the properties of weld joints.

Grain refining in weld metal using short-pulsed laser ablation during CW laser welding of 2024-T3 aluminum alloy

The 2024 aluminum alloy is used extensively in the aircraft and aerospace industries because of its excellent mechanical properties.However,the weldability of 2024 aluminum alloy is generally low because it contains a high number of solutes,such as copper(Cu),magnesium(Mg),and manganese(Mn),causing solidification cracking.If high speed welding of 2024 aluminum alloy without the use of filler is achieved,the applicability of 2024 aluminum alloys will expand.Grain refining is one of the methods used to prevent solidification cracking in weld metal,although it has never been achieved for high-speed laser welding of 2024 aluminum alloy without filler.Here,we propose a short-pulsed,laser-induced,grain-refining method during continuous wave laser welding without filler.Bead-on-plate welding was performed on a 2024-T3 aluminum alloy at a welding speed of 1 m min−1 with a single mode fiber laser at a wavelength of 1070 nm and power of 1 kW.Areas in and around the molten pool were irradiated with nanosecond laser pulses at a wavelength of 1064 nm,pulse width of 10 ns,and pulse energy of 430 mJ.The grain-refinement effect was confirmed when laser pulses were irradiated on the molten pool.The grain-refinement region was formed in a semicircular shape along the solid–liquid interface.Results of the vertical section indicate that the grain-refinement region reached a depth of 1 mm along the solid–liquid interface.The Vickers hardness test results demonstrated that the hardness increased as a result of grain refinement and that the progress of solidification cracking was suppressed in the grain refinement region.

Effect of Pulsed Current TIG Welding Parameters on Pitting Corrosion Behaviour of AA6061 Aluminium Alloy

中等力量铝合金( Al-Mg-Si 合金)收集了轻重量的制造组织要求高力量重量比率的宽 acceptancein ，如此的 astransportable 桥 girders ，军事车辆，为铝合金焊接过程的道路油轮和铁路运输 systems.Thepreferred 经常是 TIG (钨惰性的气体)焊接到期的 toits 比较地更容易的适用性和更好的 economy.In 焊接这合金的 ofthinner 节的单个通行证 TIG 的盒子。

Numerical analysis of transient keyhole shape in pulsed current plasma arc welding

Based on the characteristics of ＂one keyhole in a pulse＂ in pulsed current plasma arc welding （PAW） , the transient variation process of weld pool in a pulse cycle is simulated through the establishment of corresponding heat source model. And considering the effects of gravitational force, plasma arc pressure and surface tension on the weld pool surface, the dynamic change features of the keyhole shape in a pulse cycle are calculated by using surface deformation equation. Experiments are conducted and validate that the calctdated weld fusion line is in good agreement with the experimental results.

Numerical analysis of weld pool geometry in pulsed current plasma arc welding

Numerical analysis of weld pool shape and size is of great significance for selection and optimization of the process parameters in pulsed current plasma arc welding （PAW）. In this paper, a mathematical model and relevant algorithm are developed to determine the temperature profiles and weld pool geometry in pulsed current PAW through employing an adaptive heat source model. The volumetric heat source consists of semi-ellipsoid at upper part and a conic body at lower part along the workpiece thickness direction. The dynamic variation features of weld pool shape during a pulse cycle are numerically simulated. The calculated weld cross-section is consistent with the measure one.

Interfacial reaction control during pulsed argon arc welding of SiC_p/Al composites

The interfacial reaction control of SiC_p/2124Al composites was investigated during pulsed argon arc welding. Meanwhile, the mechanical properties, the metallographic structure and interfacial microstructure of the induced welding joint were tested and detected, respectively. The results reveal that the joint with excellent properties could be achieved by the proper selection of the special filling material and the addition of the pulse during welding. Moreover, the formation mechanism of the welding joint was discussed and the corresponding measures on further improving the quality of the welding joint of SiC_p/2124Al composites were put forward in the condition of pulsed argon arc welding.