Joining of aluminum to steel has attracted significant attention from the welding research community,automotive and rail transportation industries.Many current welding methods have been developed and applied,however,t...Joining of aluminum to steel has attracted significant attention from the welding research community,automotive and rail transportation industries.Many current welding methods have been developed and applied,however,they can not precisely control the heat input to work-piece,they are high costs,low efficiency and consist lots of complex welding devices,and the generated intermetallic compound layer in weld bead interface is thicker.A novel pulsed double electrode gas metal arc welding（Pulsed DE-GMAW）method is developed.To achieve a stable welding process for joining of aluminum to steel,a mathematical model of coupled arc is established,and a new control scheme that uses the average feedback arc voltage of main loop to adjust the wire feed speed to control coupled arc length is proposed and developed.Then,the impulse control simulation of coupled arc length,wire feed speed and wire extension is conducted to demonstrate the mathematical model and predict the stability of welding process by changing the distance of contact tip to work-piece（CTWD）.To prove the proposed PSO based PID control scheme’s feasibility,the rapid prototyping experimental system is setup and the bead-on-plate control experiments are conducted to join aluminum to steel.The impulse control simulation shows that the established model can accurately represent the variation of coupled arc length,wire feed speed and the average main arc voltage when the welding process is disturbed,and the developed controller has a faster response and adjustment,only runs about 0.1 s.The captured electric signals show the main arc voltage gradually closes to the supposed arc voltage by adjusting the wire feed speed in 0.8 s.The obtained typical current waveform demonstrates that the main current can be reduced by controlling the bypass current under maintaining a relative large total current.The control experiment proves the accuracy of proposed model and feasibility of new control scheme further.The beautiful and smooth weld beads are also obtained by this method.Pulsed DE-GMAW can thus be considered as an alternative method for low cost,high efficiency joining of aluminum to steel.展开更多
Digital pulsed metal inert gas welding machine with double closed-loop control mode is designed and implemented. It realizes precision control for real time energy and demonstrates the flexibility of digital control. ...Digital pulsed metal inert gas welding machine with double closed-loop control mode is designed and implemented. It realizes precision control for real time energy and demonstrates the flexibility of digital control. Test results of design prototype show that the designed control strategy can effectively adapt to the change of arc length and achieve ideal droplet transfer via one drop per pulse mode. Thus the welding process is stable and the weld bead is good.展开更多
In view of the unstable welding process of Tri-Arc DE,surfacing test with Q235 steel plate was completed with the help of the self-built high-speed camera and waveform synchronous acquisition system using the Tri-Arc ...In view of the unstable welding process of Tri-Arc DE,surfacing test with Q235 steel plate was completed with the help of the self-built high-speed camera and waveform synchronous acquisition system using the Tri-Arc DE technology. The effects of pulsed M-Arc frequency on Tri-Arc DE droplet transfer and weld formation were analyzed. The results show that while the gradual increase of pulse frequency,the droplet transfer frequency gradually decreases,which is followed by several drops per pulse,one drop per pulse,and one drop within several pulses. The most ideal transfer form is one drop per pulse,of which the welding process is the most stable,and the quality of weld formation is the most satisfied.展开更多
A novel surface technique has been developed to produce ZrO2 and ZrO2-Y2O3 coatings on the surface of alloys by using double pulsed plasma arc to react with a so-lution film containing nano-oxide particles. These coat...A novel surface technique has been developed to produce ZrO2 and ZrO2-Y2O3 coatings on the surface of alloys by using double pulsed plasma arc to react with a so-lution film containing nano-oxide particles. These coatings exhibit smooth surface and excellent adhesion with substrate. The morphologies of the ceramic coatings and phases were analyzed. It was shown that the oxidation resistance of 18-8 stainless steel was markedly improved by applying ZrO2 and ZrO2-Y2O3 coatings.展开更多
针对为了实现铝-钢高效高质量的连接,提出一种高效低热输入的脉冲旁路耦合电弧熔化极惰性气体保护焊(Double-electrode gas metal arc welding,DE-GMAW)方法。为了使其焊接过程熔滴平稳过渡,分析旁路电弧对熔滴过渡时电流密度的影响,确...针对为了实现铝-钢高效高质量的连接,提出一种高效低热输入的脉冲旁路耦合电弧熔化极惰性气体保护焊(Double-electrode gas metal arc welding,DE-GMAW)方法。为了使其焊接过程熔滴平稳过渡,分析旁路电弧对熔滴过渡时电流密度的影响,确定脉冲DE-GMAW熔滴过渡时电磁力的作用机制,在主路为脉冲电流情况下,分别设计旁路波形与主路组合形式即为恒定电流、交替脉冲电流和同步脉冲电流三种形式的研究,并使用高速摄像拍摄熔滴过渡图像,进行对比分析试验验证。结果表明,焊接电流波形及组合形式不同会导致作用于焊接熔滴的受力发生改变,从而使得焊接过程的稳定性与焊接质量也发生变化,对比分析得出采用同步脉冲电流时的脉冲旁路耦合电弧熔化极惰性气体保护焊焊接过程稳定、熔滴过渡均匀一致且焊缝成形平整美观。展开更多
基金Supported by National Natural Science Foundation of China(Grant No.51165023)Project of International Cooperation and Exchanges of National Natural Science Foundation of China(Grant No.51210105024)+1 种基金Financial Commission of Gansu Province of Chinathe Hong Liu Outstanding Talent Training Plan of Lanzhou University of Technology,China(Grant No.J201201)
文摘Joining of aluminum to steel has attracted significant attention from the welding research community,automotive and rail transportation industries.Many current welding methods have been developed and applied,however,they can not precisely control the heat input to work-piece,they are high costs,low efficiency and consist lots of complex welding devices,and the generated intermetallic compound layer in weld bead interface is thicker.A novel pulsed double electrode gas metal arc welding（Pulsed DE-GMAW）method is developed.To achieve a stable welding process for joining of aluminum to steel,a mathematical model of coupled arc is established,and a new control scheme that uses the average feedback arc voltage of main loop to adjust the wire feed speed to control coupled arc length is proposed and developed.Then,the impulse control simulation of coupled arc length,wire feed speed and wire extension is conducted to demonstrate the mathematical model and predict the stability of welding process by changing the distance of contact tip to work-piece（CTWD）.To prove the proposed PSO based PID control scheme’s feasibility,the rapid prototyping experimental system is setup and the bead-on-plate control experiments are conducted to join aluminum to steel.The impulse control simulation shows that the established model can accurately represent the variation of coupled arc length,wire feed speed and the average main arc voltage when the welding process is disturbed,and the developed controller has a faster response and adjustment,only runs about 0.1 s.The captured electric signals show the main arc voltage gradually closes to the supposed arc voltage by adjusting the wire feed speed in 0.8 s.The obtained typical current waveform demonstrates that the main current can be reduced by controlling the bypass current under maintaining a relative large total current.The control experiment proves the accuracy of proposed model and feasibility of new control scheme further.The beautiful and smooth weld beads are also obtained by this method.Pulsed DE-GMAW can thus be considered as an alternative method for low cost,high efficiency joining of aluminum to steel.
基金Supported by National Natural Science Foundation of China （ Grant No. 50875088）.
文摘Digital pulsed metal inert gas welding machine with double closed-loop control mode is designed and implemented. It realizes precision control for real time energy and demonstrates the flexibility of digital control. Test results of design prototype show that the designed control strategy can effectively adapt to the change of arc length and achieve ideal droplet transfer via one drop per pulse mode. Thus the welding process is stable and the weld bead is good.
基金Project was supported by the National Natural Science Foundation of China(Grant No.U1733125)Natural Science Foundation of Tianjin(Grant No.18JCYBJC19100,18JCYJC18700)
文摘In view of the unstable welding process of Tri-Arc DE,surfacing test with Q235 steel plate was completed with the help of the self-built high-speed camera and waveform synchronous acquisition system using the Tri-Arc DE technology. The effects of pulsed M-Arc frequency on Tri-Arc DE droplet transfer and weld formation were analyzed. The results show that while the gradual increase of pulse frequency,the droplet transfer frequency gradually decreases,which is followed by several drops per pulse,one drop per pulse,and one drop within several pulses. The most ideal transfer form is one drop per pulse,of which the welding process is the most stable,and the quality of weld formation is the most satisfied.
基金This work was supported by the National Natural Science Foundation of China (Grant No. 59871004).
文摘A novel surface technique has been developed to produce ZrO2 and ZrO2-Y2O3 coatings on the surface of alloys by using double pulsed plasma arc to react with a so-lution film containing nano-oxide particles. These coatings exhibit smooth surface and excellent adhesion with substrate. The morphologies of the ceramic coatings and phases were analyzed. It was shown that the oxidation resistance of 18-8 stainless steel was markedly improved by applying ZrO2 and ZrO2-Y2O3 coatings.
文摘针对为了实现铝-钢高效高质量的连接,提出一种高效低热输入的脉冲旁路耦合电弧熔化极惰性气体保护焊(Double-electrode gas metal arc welding,DE-GMAW)方法。为了使其焊接过程熔滴平稳过渡,分析旁路电弧对熔滴过渡时电流密度的影响,确定脉冲DE-GMAW熔滴过渡时电磁力的作用机制,在主路为脉冲电流情况下,分别设计旁路波形与主路组合形式即为恒定电流、交替脉冲电流和同步脉冲电流三种形式的研究,并使用高速摄像拍摄熔滴过渡图像,进行对比分析试验验证。结果表明,焊接电流波形及组合形式不同会导致作用于焊接熔滴的受力发生改变,从而使得焊接过程的稳定性与焊接质量也发生变化,对比分析得出采用同步脉冲电流时的脉冲旁路耦合电弧熔化极惰性气体保护焊焊接过程稳定、熔滴过渡均匀一致且焊缝成形平整美观。
