Considering the fact that the temperature distribution in furnace of a tangential fired pulverized coal boiler is difficult to be measured and monitored, two-stage numerical simulation method was put forward. First, m...Considering the fact that the temperature distribution in furnace of a tangential fired pulverized coal boiler is difficult to be measured and monitored, two-stage numerical simulation method was put forward. First, multi-field coupling simulation in typical work conditions was carried out off-line with the software CFX-4.3, and then the expression of temperature profile varying with operating parameter was obtained. According to real-time operating parameters, the temperature at arbitrary point of the furnace can be calculated by using this expression. Thus the temperature profile can be shown on-line and monitoring for combustion state in the furnace is realized. The simul-(ation) model was checked by the parameters measured in an operating boiler, (DG130-9.8/540.) The maximum of relative error is less than 12% and the absolute error is less than 120℃, which shows that the proposed two-stage simulation method is reliable and able to satisfy the requirement of industrial application.展开更多
Researches on the NOx emission characteristics of HT （Huangtai coal）, LC（Laicheng） coal are carried out in different atmosphere. The results show that the NOx emission time is postponed in O2/N2 atmosphere mixed w...Researches on the NOx emission characteristics of HT （Huangtai coal）, LC（Laicheng） coal are carried out in different atmosphere. The results show that the NOx emission time is postponed in O2/N2 atmosphere mixed with CO. The releasing times of volatile nitrogen and char nitrogen approach, the amount of NOx reduces. In high 02 concentration atmosphere mixed with CO2, the nitrogen releasing times cane ahead of time, NOx congregate in the beginning of the combustion. On the contrary, nitrogen releases separately, and the amount of NOx reduces greatly.展开更多
Aiming at the optimization of the operation condition, a general numerical method for calculating pulverized coal combustion in a full scale furnace fired tangentially at four corners is adopted. “ k ε ” turbulence...Aiming at the optimization of the operation condition, a general numerical method for calculating pulverized coal combustion in a full scale furnace fired tangentially at four corners is adopted. “ k ε ” turbulence model is used for the gas phases and a stochastic approach based on the Lagrangian technique is used for particle phases. Two competing reactions model for the coal devolatilization and PDF (the probability density function) method for the combustion of the gas phases are employed. In the numerical simulations, assuming the air distribution of second port level is of pagoda, waist drum and uniform type. The results show that pagoda type air distribution is advantageous to ignition and smooth combustion of pulverized coal, and suitable to inferior coal combustion in practice. In the present furnace, the igniting distance at 1st and 3rd corner is longer than that at 2nd and 4th corner. The results from numerical calculations are in good agreement with those of observed in practice.展开更多
The present paper describes the numerical investigation for a newly developed pulverized coal rich/lean burner used in the utility boilers. The mechanism of the rich/lean separation process of the pulverized coal are ...The present paper describes the numerical investigation for a newly developed pulverized coal rich/lean burner used in the utility boilers. The mechanism of the rich/lean separation process of the pulverized coal are analyzed and the effect of the height of the baffle body and the different particle sizes on the separation efficiency are considered. It is concluded that the burner is applicable in industry.展开更多
High temperature air combustion is a prospecting technology in energy saving and pollutants reduction. Numerical simulation on pulverized coal combustion and NOx emissions in high temperature air from circulating flui...High temperature air combustion is a prospecting technology in energy saving and pollutants reduction. Numerical simulation on pulverized coal combustion and NOx emissions in high temperature air from circulating fluidized bed was presented. The down-fired combustor, taken as the calculation domain, has the diameter of 220 mm and the height of 3000 mm. 2 cases with air staging combustion are simulated. Compared the simulation results with experimental data, there is a good agreement. It is found that the combustion model and NOx formation model are applicable to simulate the pulverized coal combustion and NOx emissions in high temperature air from circulating fluidized bed. The results show that there is a uniform temperature profile along the axis of the down-fired combustor. The NOx emissions are lower than those of ordinary pulverized coal combustion, and the NOx emissions are 390 mg/m3 and 352 mg/m3 in Case 1 and Case 2, respectively. At the range of 300-600 mm below the nozzle, the NO concentration decreases, mainly resulting from some homogeneous reactions and heterogeneous reaction. NO concentration has a little increase at the position of 800 mm below the nozzle as the tertiary air supplied to the combustor at the position of 600 mm below the nozzle.展开更多
A local thermal stress model of water-cooled-wall pulverized-coal gasifier was built, and ANSYS was used to simulate the stress field in the gasifier operation to research the damage of refractories and slag layer cau...A local thermal stress model of water-cooled-wall pulverized-coal gasifier was built, and ANSYS was used to simulate the stress field in the gasifier operation to research the damage of refractories and slag layer caused by the thermal stress. The results reveal that:（1） the maximum stress of water-cooled-wall gasifier appears at the interface between anchor nails and refractories as well as the interface between refractories and the slag layer, and the maximum stress of slag layer appears on the surface of the slag layer;（2） the increase of slag layer thickness can significantly reduce the thermal stress at the interface between anchor nails and refractories, but increase the thermal stress between slag layer and refractories;（3） when the therma I conductivity is 2-6 W · m-1 · K-1, the thermal stress increases rapidly with the increase of the thermal conductivity, but when the thermal conductivity is 6-10 W · m-1 · K-1, the thermal stress is basically stable;（4） the higher the cooling rate, the faster the decreasing speed of the temperature and thermal stress.展开更多
In the present paper, a multifluid model of two-phase flows with pulverized-coal combustion, based on a continuum-trajectory model with reacting particle phase, is developed and employed to simulate the 3-D turbulent ...In the present paper, a multifluid model of two-phase flows with pulverized-coal combustion, based on a continuum-trajectory model with reacting particle phase, is developed and employed to simulate the 3-D turbulent two-phase hows and combustion in a new type of pulverized-coal combustor with one primary-air jet placed along the wall of the combustor. The results show that: (1) this continuum-trajectory model with reacting particle phase can be used in practical engineering to qualitatively predict the flame stability, concentrations of gas species, possibilities of slag formation and soot deposition, etc.; (2) large recirculation zones can be created in the combustor, which is favorable to the ignition and flame stabilization.展开更多
Burning coal briquettes or biomass pellets in household decoupling stoves is of significance to the reduction of residential pollutant emissions such as NO and CO. In order to make full use of the superiority of decou...Burning coal briquettes or biomass pellets in household decoupling stoves is of significance to the reduction of residential pollutant emissions such as NO and CO. In order to make full use of the superiority of decoupling combustion technology, the household stoves should be specially designed and optimized to adapt to fuel types and combustion characteristics. Using numerical simulation and experimental validation, this study quantitatively clarified that the reducibility of devolatilization char plays an important role in the suppression of NO emission in the decoupling combustion of coal, while the reducibility of pyrolysis gases has a dominant effect on the reduction of NO in the decoupling combustion of biomass. An optimal parameter combination of throat height and grate angle was obtained for the simultaneous suppression of NO and CO emissions in the household decoupling stove burning coal briquettes. Two types of decoupling stoves were developed to enable the clean combustion of biomass pellets. The A-type biomass stove with a multi-pass smoke tunnel shows a better comprehensive NO and CO reduction effectiveness than the B-type biomass stove consisting of a two-stage grate structure and an S-shaped pyrolysis chamber. The optimal structural parameters provided references for the design and manufacture of commercial decoupling coal and biomass stoves.展开更多
With the objective of producing a full-scale tiny-oil ignition burner, identical to the burner used in an 800 MWe utility boiler, numerical simulations were performed using Fluent 6.3.26 to study the progress of ignit...With the objective of producing a full-scale tiny-oil ignition burner, identical to the burner used in an 800 MWe utility boiler, numerical simulations were performed using Fluent 6.3.26 to study the progress of ignition for four coal concentration settings covering sub- operation conditions prevailing during the experiments performed with the burner. The numerical simulations conformed to the experimental results, demonstrating the suitability of the model used in the calculations. Simula- tions for a coal concentration of 0.40 kg/kg corresponding to a single burner operating at its rated output were also conducted, which indicated that gas temperatures along the burner centerline were high. As gas flowed to the burner nozzle, the high-temperature region expanded, ensuring a successful pulverized-coal ignition. With increasing coal concentration （0.08-0.40 kg/kg）, the gas temperature along the burner centerline and at the first and second combustion chamber exits decreased at the equivalent radial points. At the center of the second combustion chamber exit, the O2 concentrations were almost depleted for the five coal concentrations, while the CO concentrations peaked.展开更多
The progression of ignition was numerically simulated with the aim of realizing a full-scale tiny-oil ignition burner that is identical to the burner used in an 800 MWe utility boiler. The numerical simulations were c...The progression of ignition was numerically simulated with the aim of realizing a full-scale tiny-oil ignition burner that is identical to the burner used in an 800 MWe utility boiler. The numerical simulations were conducted for four excess air ratios, 0.56, 0.75, 0.98 and 1.14 （corresponding to primary air velocities of 17, 23, 30 and 35 m/s, respectively）, which were chosen because they had been used previously in practical experiments. The numerical simulations agreed well with the experimental results, which demonstrate the suitability of the model used in the calculations. The gas temperatures were high along the center line of the burner for the four excess air ratios. The flame spread to the bumer wall and the high- temperature region was enlarged in the radial direction along the primary air flow direction. The O2 concentrations for the four excess air ratios were 0.5%, 1.1%, 0.9% and 3.0% at the exit of the second combustion chamber. The CO peak concentration was very high with values of 7.9%, 9.9%, 11.3% and 10.6% for the four excess air ratios at the exit of the second combustion chamber.展开更多
文摘Considering the fact that the temperature distribution in furnace of a tangential fired pulverized coal boiler is difficult to be measured and monitored, two-stage numerical simulation method was put forward. First, multi-field coupling simulation in typical work conditions was carried out off-line with the software CFX-4.3, and then the expression of temperature profile varying with operating parameter was obtained. According to real-time operating parameters, the temperature at arbitrary point of the furnace can be calculated by using this expression. Thus the temperature profile can be shown on-line and monitoring for combustion state in the furnace is realized. The simul-(ation) model was checked by the parameters measured in an operating boiler, (DG130-9.8/540.) The maximum of relative error is less than 12% and the absolute error is less than 120℃, which shows that the proposed two-stage simulation method is reliable and able to satisfy the requirement of industrial application.
基金supported by the Natural Science Foundation for Young Scientists of Shanxi Province(No.2008041002)
文摘Researches on the NOx emission characteristics of HT （Huangtai coal）, LC（Laicheng） coal are carried out in different atmosphere. The results show that the NOx emission time is postponed in O2/N2 atmosphere mixed with CO. The releasing times of volatile nitrogen and char nitrogen approach, the amount of NOx reduces. In high 02 concentration atmosphere mixed with CO2, the nitrogen releasing times cane ahead of time, NOx congregate in the beginning of the combustion. On the contrary, nitrogen releases separately, and the amount of NOx reduces greatly.
文摘Aiming at the optimization of the operation condition, a general numerical method for calculating pulverized coal combustion in a full scale furnace fired tangentially at four corners is adopted. “ k ε ” turbulence model is used for the gas phases and a stochastic approach based on the Lagrangian technique is used for particle phases. Two competing reactions model for the coal devolatilization and PDF (the probability density function) method for the combustion of the gas phases are employed. In the numerical simulations, assuming the air distribution of second port level is of pagoda, waist drum and uniform type. The results show that pagoda type air distribution is advantageous to ignition and smooth combustion of pulverized coal, and suitable to inferior coal combustion in practice. In the present furnace, the igniting distance at 1st and 3rd corner is longer than that at 2nd and 4th corner. The results from numerical calculations are in good agreement with those of observed in practice.
文摘The present paper describes the numerical investigation for a newly developed pulverized coal rich/lean burner used in the utility boilers. The mechanism of the rich/lean separation process of the pulverized coal are analyzed and the effect of the height of the baffle body and the different particle sizes on the separation efficiency are considered. It is concluded that the burner is applicable in industry.
基金the support of the National Natural Science Foundation of China (51006103)
文摘High temperature air combustion is a prospecting technology in energy saving and pollutants reduction. Numerical simulation on pulverized coal combustion and NOx emissions in high temperature air from circulating fluidized bed was presented. The down-fired combustor, taken as the calculation domain, has the diameter of 220 mm and the height of 3000 mm. 2 cases with air staging combustion are simulated. Compared the simulation results with experimental data, there is a good agreement. It is found that the combustion model and NOx formation model are applicable to simulate the pulverized coal combustion and NOx emissions in high temperature air from circulating fluidized bed. The results show that there is a uniform temperature profile along the axis of the down-fired combustor. The NOx emissions are lower than those of ordinary pulverized coal combustion, and the NOx emissions are 390 mg/m3 and 352 mg/m3 in Case 1 and Case 2, respectively. At the range of 300-600 mm below the nozzle, the NO concentration decreases, mainly resulting from some homogeneous reactions and heterogeneous reaction. NO concentration has a little increase at the position of 800 mm below the nozzle as the tertiary air supplied to the combustor at the position of 600 mm below the nozzle.
文摘A local thermal stress model of water-cooled-wall pulverized-coal gasifier was built, and ANSYS was used to simulate the stress field in the gasifier operation to research the damage of refractories and slag layer caused by the thermal stress. The results reveal that:（1） the maximum stress of water-cooled-wall gasifier appears at the interface between anchor nails and refractories as well as the interface between refractories and the slag layer, and the maximum stress of slag layer appears on the surface of the slag layer;（2） the increase of slag layer thickness can significantly reduce the thermal stress at the interface between anchor nails and refractories, but increase the thermal stress between slag layer and refractories;（3） when the therma I conductivity is 2-6 W · m-1 · K-1, the thermal stress increases rapidly with the increase of the thermal conductivity, but when the thermal conductivity is 6-10 W · m-1 · K-1, the thermal stress is basically stable;（4） the higher the cooling rate, the faster the decreasing speed of the temperature and thermal stress.
基金Sponsored by the National Key Projects of Fundamental Research of China.
文摘In the present paper, a multifluid model of two-phase flows with pulverized-coal combustion, based on a continuum-trajectory model with reacting particle phase, is developed and employed to simulate the 3-D turbulent two-phase hows and combustion in a new type of pulverized-coal combustor with one primary-air jet placed along the wall of the combustor. The results show that: (1) this continuum-trajectory model with reacting particle phase can be used in practical engineering to qualitatively predict the flame stability, concentrations of gas species, possibilities of slag formation and soot deposition, etc.; (2) large recirculation zones can be created in the combustor, which is favorable to the ignition and flame stabilization.
基金financial supports from the “Transformational Technologies for Clean Energy and Demonstration”, Strategic Priority Research Program of Chinese Academy of Sciences (XDA21040400)。
文摘Burning coal briquettes or biomass pellets in household decoupling stoves is of significance to the reduction of residential pollutant emissions such as NO and CO. In order to make full use of the superiority of decoupling combustion technology, the household stoves should be specially designed and optimized to adapt to fuel types and combustion characteristics. Using numerical simulation and experimental validation, this study quantitatively clarified that the reducibility of devolatilization char plays an important role in the suppression of NO emission in the decoupling combustion of coal, while the reducibility of pyrolysis gases has a dominant effect on the reduction of NO in the decoupling combustion of biomass. An optimal parameter combination of throat height and grate angle was obtained for the simultaneous suppression of NO and CO emissions in the household decoupling stove burning coal briquettes. Two types of decoupling stoves were developed to enable the clean combustion of biomass pellets. The A-type biomass stove with a multi-pass smoke tunnel shows a better comprehensive NO and CO reduction effectiveness than the B-type biomass stove consisting of a two-stage grate structure and an S-shaped pyrolysis chamber. The optimal structural parameters provided references for the design and manufacture of commercial decoupling coal and biomass stoves.
基金sponsored by the Hi-Tech Research and Development Program of China （863 program） （Grant No. 2006AA05Z321） and supported by the Foundation for Innovative Research Groups of the National Natural Science Foundation of China （Grant No. 51121004）.
文摘With the objective of producing a full-scale tiny-oil ignition burner, identical to the burner used in an 800 MWe utility boiler, numerical simulations were performed using Fluent 6.3.26 to study the progress of ignition for four coal concentration settings covering sub- operation conditions prevailing during the experiments performed with the burner. The numerical simulations conformed to the experimental results, demonstrating the suitability of the model used in the calculations. Simula- tions for a coal concentration of 0.40 kg/kg corresponding to a single burner operating at its rated output were also conducted, which indicated that gas temperatures along the burner centerline were high. As gas flowed to the burner nozzle, the high-temperature region expanded, ensuring a successful pulverized-coal ignition. With increasing coal concentration （0.08-0.40 kg/kg）, the gas temperature along the burner centerline and at the first and second combustion chamber exits decreased at the equivalent radial points. At the center of the second combustion chamber exit, the O2 concentrations were almost depleted for the five coal concentrations, while the CO concentrations peaked.
文摘The progression of ignition was numerically simulated with the aim of realizing a full-scale tiny-oil ignition burner that is identical to the burner used in an 800 MWe utility boiler. The numerical simulations were conducted for four excess air ratios, 0.56, 0.75, 0.98 and 1.14 （corresponding to primary air velocities of 17, 23, 30 and 35 m/s, respectively）, which were chosen because they had been used previously in practical experiments. The numerical simulations agreed well with the experimental results, which demonstrate the suitability of the model used in the calculations. The gas temperatures were high along the center line of the burner for the four excess air ratios. The flame spread to the bumer wall and the high- temperature region was enlarged in the radial direction along the primary air flow direction. The O2 concentrations for the four excess air ratios were 0.5%, 1.1%, 0.9% and 3.0% at the exit of the second combustion chamber. The CO peak concentration was very high with values of 7.9%, 9.9%, 11.3% and 10.6% for the four excess air ratios at the exit of the second combustion chamber.
