For the quad tilt rotor aircraft, a computational fluid dynamics method based on multiple reference frames (MRF) was used to analyze the influence of aerodynamic layout parameters on the aerodynamic characteristics of...For the quad tilt rotor aircraft, a computational fluid dynamics method based on multiple reference frames (MRF) was used to analyze the influence of aerodynamic layout parameters on the aerodynamic characteristics of the quad tilt rotor aircraft. Firstly, a numerical simulation method for the interference flow field of the quad tilt rotor aircraft is established. Based on this method, the aerodynamic characteristics of isolated rotors, rotor combinations at different lateral positions on the wing, and rotor rotation directions under different inflow velocities were calculated and analyzed, in order to grasp their aerodynamic interference laws and provide reference for the design and control theory research of such aircraft.展开更多
The QUAD(Quasi-Accurate Detection of gross errors) method which is originally developed to detect gross errors in the geodetic data is extended and used to select and identify relatively stable stations. The formulas ...The QUAD(Quasi-Accurate Detection of gross errors) method which is originally developed to detect gross errors in the geodetic data is extended and used to select and identify relatively stable stations. The formulas and algorithm are described in detail. Some problems that should be noticed in the use of this method are discussed. Finally, this method is applied to some data observed in North China as an example.展开更多
The aerodynamic model of propeller,wing,fuselage and vertical tail are established for the tilt quad rotor(TQR)with partial tilt-wing,and then the flight dynamic model is established.Based on the six-degree-of-freedom...The aerodynamic model of propeller,wing,fuselage and vertical tail are established for the tilt quad rotor(TQR)with partial tilt-wing,and then the flight dynamic model is established.Based on the six-degree-of-freedom equation and the small disturbance linearization assumption,the trimming and stability of the tilt quad rotor with partial tilt-wing and the tilt quad rotor without tilt-wing are analyzed.The results show that in the hovering state,due to the existence of tilt-wing,the propeller wake reduces the downwash on the wing,thereby reducing the vertical weight gain of the aircraft.It is beneficial to increase the endurance time and improve the endurance performance.The transition corridor of the TQR with tilt-wing is narrower than that of the TQR without tilt-wing,but the transition corridor of TQR with tilt-wing still has a large space for design.Furthermore,the stability analysis shows that the Dutch roll damping ratio is larger,and in other modes the aircraft has a certain stability.The manipulation response analysis shows that in the transition mode the lateral-directional coupling is strong.展开更多
The finite element method（FEM） is used to analyze the effects of lead widths and pitches on reliability of soldered joints. The optimum simulation for QFP devices is also researched. The results indicate that when t...The finite element method（FEM） is used to analyze the effects of lead widths and pitches on reliability of soldered joints. The optimum simulation for QFP devices is also researched. The results indicate that when the lead pitches are the same, the maximum equivalent stress of the soldered joints increases with the increasing of lead widths, while the reliability of the soldered joints reduces. When the lead widths are the same, the maximum equivalent stress of the soldered joints doesn＇t decrease completely with the increasing of lead pitches, a minimum value of the maximum equivalent stress values exists in all the curves. Under this condition the maximum equivalent stress of the soldewed joints is relatively the least, the reliability of soldered joints is high and the assembly is excellent. The simulating results indicate the best parameter： The lead width is 0.2 mm and lead pitch is 0.3 mm （the distance between two leads is 0.1 mm）, which are benefited for the micromation of QFP devices now. The minimum value of the maximum equivalent stress of soldered joints exists while lead width is 0.25 mm and lead pitch is 0.35 mm （the distance between two leads is 0.1 mm）, the devices can serve for a long time and the reliability is the highest, the assembly is excellent. The simulating results also indicate the fact that the lead width is 0.15 mm and lead pitch is 0.2 mm maybe the limit of QFP, which is significant for the high lead count and micromation of assembly.展开更多
The acquisition of precise soil data representative of the entire survey area, is a critical issue for many treatments such as irrigation or fertilization in precision agriculture. The aim of this study was to investi...The acquisition of precise soil data representative of the entire survey area, is a critical issue for many treatments such as irrigation or fertilization in precision agriculture. The aim of this study was to investigate the spatial variability of soil bulk electrical conductivity （ECb） in a coastal saline field and design an optimized spatial sampling scheme of ECb based on a sampling design algorithm, the variance quad-tree （VQT） method. Soil ECb data were collected from the field at 20 m interval in a regular grid scheme. The smooth contour map of the whole field was obtained by ordinary kriging interpolation, VQT algorithm was then used to split the smooth contour map into strata of different number desired, the sampling locations can be selected within each stratum in subsequent sampling. The result indicated that the probability of choosing representative sampling sites was increased significantly by using VQT method with the sampling number being greatly reduced compared to grid sampling design while retaining the same prediction accuracy. The advantage of the VQT method is that this scheme samples sparsely in fields where the spatial variability is relatively uniform and more intensive where the variability is large. Thus the sampling efficiency can be improved, hence facilitate an assessment methodology that can be applied in a rapid, practical and cost-effective manner.展开更多
In view of the many scenes of unmanned aerial vehicle(UAV)detection,a third-party signal source is used to design a receiver to monitor the UAV.It is of great significance to understand the reflection of the signal il...In view of the many scenes of unmanned aerial vehicle(UAV)detection,a third-party signal source is used to design a receiver to monitor the UAV.It is of great significance to understand the reflection of the signal illuminating the UAV.Taking the communication base station(BS)signal as the third-party signal source,and considering the complete transmission link,reflection changes and loss fading of the communication signal,this study conducts model fitting for irregular UAV targets,simplifying complex targets into a combination of simple targets.Furthermore,the influence of the dielectric constant of the target surface and the signal irradiation angle on the signal reflection is analyzed.The analysis shows that the simulation results of this model fitting method are consistent with the results of other literature,which provides theoretical support for the detection of low and slow small targets such as UAVs.展开更多
Although the complex Wishart distribution has been widely used to analyze the statistic properties of quad-pol SAR spatial data, the applicability of this complex distribution to the time series of sea clutter is rare...Although the complex Wishart distribution has been widely used to analyze the statistic properties of quad-pol SAR spatial data, the applicability of this complex distribution to the time series of sea clutter is rarely discussed.The measured data of the quad-pol X-band marine radar demonstrate that the time series of the sea echoes are also satisfied the circular Gaussian distributions if the low intensity signals, which are mainly dominated by a radar noise, in the shadow regions of the large-scale waves are removed. On the basis of this fact, the probability density functions（PDFs） of the intensity as well as the phase, the real and the imaginary parts of the sea echoes obtained by the marine radar have been derived, and the theoretical models are all expressed in closed forms. In order to validate the theoretical results, the PDFs are compared with the experimental data collected by the Mc Master IPIX radar. And the comparisons show that the PDF models are in good agreement with the experimental data.展开更多
文摘For the quad tilt rotor aircraft, a computational fluid dynamics method based on multiple reference frames (MRF) was used to analyze the influence of aerodynamic layout parameters on the aerodynamic characteristics of the quad tilt rotor aircraft. Firstly, a numerical simulation method for the interference flow field of the quad tilt rotor aircraft is established. Based on this method, the aerodynamic characteristics of isolated rotors, rotor combinations at different lateral positions on the wing, and rotor rotation directions under different inflow velocities were calculated and analyzed, in order to grasp their aerodynamic interference laws and provide reference for the design and control theory research of such aircraft.
文摘The QUAD(Quasi-Accurate Detection of gross errors) method which is originally developed to detect gross errors in the geodetic data is extended and used to select and identify relatively stable stations. The formulas and algorithm are described in detail. Some problems that should be noticed in the use of this method are discussed. Finally, this method is applied to some data observed in North China as an example.
基金supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD)
文摘The aerodynamic model of propeller,wing,fuselage and vertical tail are established for the tilt quad rotor(TQR)with partial tilt-wing,and then the flight dynamic model is established.Based on the six-degree-of-freedom equation and the small disturbance linearization assumption,the trimming and stability of the tilt quad rotor with partial tilt-wing and the tilt quad rotor without tilt-wing are analyzed.The results show that in the hovering state,due to the existence of tilt-wing,the propeller wake reduces the downwash on the wing,thereby reducing the vertical weight gain of the aircraft.It is beneficial to increase the endurance time and improve the endurance performance.The transition corridor of the TQR with tilt-wing is narrower than that of the TQR without tilt-wing,but the transition corridor of TQR with tilt-wing still has a large space for design.Furthermore,the stability analysis shows that the Dutch roll damping ratio is larger,and in other modes the aircraft has a certain stability.The manipulation response analysis shows that in the transition mode the lateral-directional coupling is strong.
基金This project is supported by Provincial Six Kind Skilled Personnel Project of Jiangsu,China(No.06-E-020).
文摘The finite element method（FEM） is used to analyze the effects of lead widths and pitches on reliability of soldered joints. The optimum simulation for QFP devices is also researched. The results indicate that when the lead pitches are the same, the maximum equivalent stress of the soldered joints increases with the increasing of lead widths, while the reliability of the soldered joints reduces. When the lead widths are the same, the maximum equivalent stress of the soldered joints doesn＇t decrease completely with the increasing of lead pitches, a minimum value of the maximum equivalent stress values exists in all the curves. Under this condition the maximum equivalent stress of the soldewed joints is relatively the least, the reliability of soldered joints is high and the assembly is excellent. The simulating results indicate the best parameter： The lead width is 0.2 mm and lead pitch is 0.3 mm （the distance between two leads is 0.1 mm）, which are benefited for the micromation of QFP devices now. The minimum value of the maximum equivalent stress of soldered joints exists while lead width is 0.25 mm and lead pitch is 0.35 mm （the distance between two leads is 0.1 mm）, the devices can serve for a long time and the reliability is the highest, the assembly is excellent. The simulating results also indicate the fact that the lead width is 0.15 mm and lead pitch is 0.2 mm maybe the limit of QFP, which is significant for the high lead count and micromation of assembly.
基金We thank the financial support from the National Natural Science Foundation of China(40701007,40571066)the Postdoctoral Science Foundation of China(20060401048).
文摘The acquisition of precise soil data representative of the entire survey area, is a critical issue for many treatments such as irrigation or fertilization in precision agriculture. The aim of this study was to investigate the spatial variability of soil bulk electrical conductivity （ECb） in a coastal saline field and design an optimized spatial sampling scheme of ECb based on a sampling design algorithm, the variance quad-tree （VQT） method. Soil ECb data were collected from the field at 20 m interval in a regular grid scheme. The smooth contour map of the whole field was obtained by ordinary kriging interpolation, VQT algorithm was then used to split the smooth contour map into strata of different number desired, the sampling locations can be selected within each stratum in subsequent sampling. The result indicated that the probability of choosing representative sampling sites was increased significantly by using VQT method with the sampling number being greatly reduced compared to grid sampling design while retaining the same prediction accuracy. The advantage of the VQT method is that this scheme samples sparsely in fields where the spatial variability is relatively uniform and more intensive where the variability is large. Thus the sampling efficiency can be improved, hence facilitate an assessment methodology that can be applied in a rapid, practical and cost-effective manner.
基金supported by the State Major Research and Development Project(2018YFB1802004)the State Key Laboratory of Air Traffic Management System and Technology(SKLATM201807)。
文摘In view of the many scenes of unmanned aerial vehicle(UAV)detection,a third-party signal source is used to design a receiver to monitor the UAV.It is of great significance to understand the reflection of the signal illuminating the UAV.Taking the communication base station(BS)signal as the third-party signal source,and considering the complete transmission link,reflection changes and loss fading of the communication signal,this study conducts model fitting for irregular UAV targets,simplifying complex targets into a combination of simple targets.Furthermore,the influence of the dielectric constant of the target surface and the signal irradiation angle on the signal reflection is analyzed.The analysis shows that the simulation results of this model fitting method are consistent with the results of other literature,which provides theoretical support for the detection of low and slow small targets such as UAVs.
基金The National Key Research and Development Program of China under contract No.2016YFC1401008the National Natural Science Foundation of China under contract No.41376179the National Natural Science Foundation of China-Shandong Joint Fund for Marine Science Research Centers under contract No.U1406404
文摘Although the complex Wishart distribution has been widely used to analyze the statistic properties of quad-pol SAR spatial data, the applicability of this complex distribution to the time series of sea clutter is rarely discussed.The measured data of the quad-pol X-band marine radar demonstrate that the time series of the sea echoes are also satisfied the circular Gaussian distributions if the low intensity signals, which are mainly dominated by a radar noise, in the shadow regions of the large-scale waves are removed. On the basis of this fact, the probability density functions（PDFs） of the intensity as well as the phase, the real and the imaginary parts of the sea echoes obtained by the marine radar have been derived, and the theoretical models are all expressed in closed forms. In order to validate the theoretical results, the PDFs are compared with the experimental data collected by the Mc Master IPIX radar. And the comparisons show that the PDF models are in good agreement with the experimental data.
