The composite quasi solid state electrolytes(CQSE) is firstly synthesized with quasi solid state electrolytes(QSE) and lithium-ion-conducting material Li1.4Al0.4Ti1.6(PO4)3(LATP), and the QSE consists of [LiG4...The composite quasi solid state electrolytes(CQSE) is firstly synthesized with quasi solid state electrolytes(QSE) and lithium-ion-conducting material Li1.4Al0.4Ti1.6(PO4)3(LATP), and the QSE consists of [LiG4][TFSI] with fumed silica nanoparticles. Compared with LATP, CQSE greatly improves the interface conductance of solid electrolytes. In addition,it has lower liquid volume relative to QSE. Although the liquid volume fraction of CQSE is droped to 60%, its conductivity can also reach 1.39 × 10^-4S/cm at 20℃. Linear sweep voltammetry(LSV) is conducted on each composite electrolyte.The results show the possibility that CQSE has superior electrochemical stability up to 5.0 V versus Li/Li^+1. TG curves also show that composite electrolytes have higher thermal stability. In addition, the performance of Li/QSE/Li Mn2O4 and Li/CQSE/Li Mn2O4 batteries is evaluated and shows good electrochemical characteristics at 60℃.展开更多
Dye-sensitized solar cells (DSSCs) are the most promising, low cost and most extensively investigated solar cells. They are famous for their clean and efficient solar energy conversion. Nevertheless this, long-time ...Dye-sensitized solar cells (DSSCs) are the most promising, low cost and most extensively investigated solar cells. They are famous for their clean and efficient solar energy conversion. Nevertheless this, long-time sta- bility is still to be acquired. In recent years research on solid and quasi-solid state electrolytes is extensively in- creased. Various quasi-solid electrolytes, including composites polymer electrolytes, ionic liquid electrolytes, thermoplastic polymer electrolytes and thermosetting polymer electrolytes have been used. Performance and stability of a quasi-solid state electrolyte are between liquid and solid electrolytes. High photovoltaic performances of QS-DSSCs along better long-term stability can be obtained by designing and optimizing quasi-solid electrolytes. It is a prospective candidate for highly efficient and stable DSSCs.展开更多
The influencing mechanisms of elements Ti and Ce and their interactions on fracture behaviors of casting alloys AI-4.5Cu-0.6Mn were studied by observing tensile fracture behavior in quasi-solid zone under SEM and EDX ...The influencing mechanisms of elements Ti and Ce and their interactions on fracture behaviors of casting alloys AI-4.5Cu-0.6Mn were studied by observing tensile fracture behavior in quasi-solid zone under SEM and EDX instruments. The results indicate that the resistance stress against hot cracking can be improved obviously by addition of Ti, because of its grain refining function. It is also found that, when Ce is added into the alloys, besides its effect in refining crystalline, the mechanical behavior of lower melting point eutectic phase in quasi-solid zone can be improved efficiently by some compounds with Ce formed and deposited between dendrites. Therefore, a colligating effect of Ti and Ce on improving resistance stress against hot cracking is more efficient than that only single alloy element is applied. When hot cracking occurs, grains yield at first, and then crack spreads. Both inter-grain and trans-grain fractures are observed, but the major fracture manner is brittleness.展开更多
Scale-up synthesis of sub-micron ZSM-5 molecular sieve in a quasi-solid system was investigated. Compared with traditional hydrothermal synthesis, the synthesis in a quasi-solid system has the advantages of high yield...Scale-up synthesis of sub-micron ZSM-5 molecular sieve in a quasi-solid system was investigated. Compared with traditional hydrothermal synthesis, the synthesis in a quasi-solid system has the advantages of high yield, short crystallization time, low energy consumption as well as low emissions. However, the high solid content in the quasi-solid system can cause the mass and heat transfer problems and make scalable production difficult. In order to solve the problem, we have developed a method for the optimization of the mass and heat transfer. By this method one can vary the flow field in the reactor by changing the stirrer speed. Scale-up synthesis of the sub-micron ZSM-5 molecular sieve in a quasi-solid system was carried out in a 5 L reactor with double propeller-type agitators. The process was investigated with product characterization using X-ray diffraction (XRD) and scanning electron microscopy (SEM) and the flow field information was collected using laser Doppler velocimetry (LDV). The results showed that the flow field patterns can be tuned by using different stirrer speeds, the morphology and size of assynthesized of ZSM-5 can be effectively controlled.展开更多
A novel transparent and soft quasi-solid-state electrolyte (QSSE) was proposed and fabricated, which consists of ionic liquid (PYR14TFSI) and nano-fumed silica. The QSSE demonstrates high ionic conductivity of 4.6...A novel transparent and soft quasi-solid-state electrolyte (QSSE) was proposed and fabricated, which consists of ionic liquid (PYR14TFSI) and nano-fumed silica. The QSSE demonstrates high ionic conductivity of 4.6× 10-4 S/cm at room temperature and wide electrochemical stability window of over 5 V. The Li-O2 battery using such quasi-solidstate electrolyte exhibits a low charge-discharge overpotential at the first cycle and excellent long-term cyclability over 500 cycles.展开更多
We have made a gain-switched all-solid-state quasi-continuous-wave (QCW) tunable Ti:sapphire laser system, which is pumped by a 532 nm intracavity frequency-doubled Nd:YAG laser. Based on the theory of gain-switch...We have made a gain-switched all-solid-state quasi-continuous-wave (QCW) tunable Ti:sapphire laser system, which is pumped by a 532 nm intracavity frequency-doubled Nd:YAG laser. Based on the theory of gain-switching and the study on the influencing factors of the output pulse width, an effective method for obtaining high power and narrow pulse width output is proposed. Through deliberately designing the pump source and the resonator of the Ti:sapphire laser, when the repetition rate is 6 kHz and the length of the cavity is 220 mm, at an incident pump power of 22 W, the tunable Ti:sapphire laser from 700 to 950nm can be achieved. It has a maximum average output power of 5.6W at 800nm and the pulse width of 13.2 ns, giving an optical conversion efficiency of 25.5% from the 532 mn pump laser to the Ti:sapphire laser.展开更多
In order to study the settling mechanism of particles in an air-solid magnetically stabilized fluidized bed(MSFB) for separation,we carried out free settling and quasi-zero settling tests on the tracing particles.The ...In order to study the settling mechanism of particles in an air-solid magnetically stabilized fluidized bed(MSFB) for separation,we carried out free settling and quasi-zero settling tests on the tracing particles.The results show that the main resistance forces as the tracing particles settled in an air-solid MSFB were motion resistance force and yield force.The motion resistance and yield forces greatly hindered the free settling of the particles by greatly decreasing the acceleration for settling process of the particles.The acceleration decreased from 3022.62 cm/s 2 to zero in 0.1 s,and in the end,the particles stopped in the air-solid MSFB.The yield force on particles increased with increasing the magnetic field intensity,resulting in decrease of the quasi-zero settling displacement.However,the yield force on particles decreased with increasing the fluidized air velocity,leading to increase of the quasi-zero settling displacement.When the structure and operating parameters of the air-solid MSFB were set up,the yield stress on particles stopped in an air-solid MSFB was a function of diameter and density of particles.The settling displacements of equal diameter particles increased with increasing their densities,and the settling displacements of equal density particles increased with increasing their diameters.展开更多
Based on convolution-type constitutive equations for linear viscoelastic materials with damage and the hypotheses of Timoshenko beams, the equations governing quasi-static and dynamical behavior of Timoshenko beams wi...Based on convolution-type constitutive equations for linear viscoelastic materials with damage and the hypotheses of Timoshenko beams, the equations governing quasi-static and dynamical behavior of Timoshenko beams with damage were first derived. The quasi-static behavior of the viscoelastic Timoshenko beam under step loading was analyzed and the analytical solution was obtained in the Laplace transformation domain. The deflection and damage curves at different time were obtained by using the numerical inverse transform and the influences of material parameters on the quasi-static behavior of the beam were investigated in detail.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.52315206 and 51502334)the Funds from the Ministry of Science and Technology of China(Grant No.2016YFB0100100)+1 种基金the Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDA09010000)the Foundation from Beijing Municipal Science&Technology Commission(Grant No.D171100005517001)
文摘The composite quasi solid state electrolytes(CQSE) is firstly synthesized with quasi solid state electrolytes(QSE) and lithium-ion-conducting material Li1.4Al0.4Ti1.6(PO4)3(LATP), and the QSE consists of [LiG4][TFSI] with fumed silica nanoparticles. Compared with LATP, CQSE greatly improves the interface conductance of solid electrolytes. In addition,it has lower liquid volume relative to QSE. Although the liquid volume fraction of CQSE is droped to 60%, its conductivity can also reach 1.39 × 10^-4S/cm at 20℃. Linear sweep voltammetry(LSV) is conducted on each composite electrolyte.The results show the possibility that CQSE has superior electrochemical stability up to 5.0 V versus Li/Li^+1. TG curves also show that composite electrolytes have higher thermal stability. In addition, the performance of Li/QSE/Li Mn2O4 and Li/CQSE/Li Mn2O4 batteries is evaluated and shows good electrochemical characteristics at 60℃.
文摘Dye-sensitized solar cells (DSSCs) are the most promising, low cost and most extensively investigated solar cells. They are famous for their clean and efficient solar energy conversion. Nevertheless this, long-time sta- bility is still to be acquired. In recent years research on solid and quasi-solid state electrolytes is extensively in- creased. Various quasi-solid electrolytes, including composites polymer electrolytes, ionic liquid electrolytes, thermoplastic polymer electrolytes and thermosetting polymer electrolytes have been used. Performance and stability of a quasi-solid state electrolyte are between liquid and solid electrolytes. High photovoltaic performances of QS-DSSCs along better long-term stability can be obtained by designing and optimizing quasi-solid electrolytes. It is a prospective candidate for highly efficient and stable DSSCs.
文摘The influencing mechanisms of elements Ti and Ce and their interactions on fracture behaviors of casting alloys AI-4.5Cu-0.6Mn were studied by observing tensile fracture behavior in quasi-solid zone under SEM and EDX instruments. The results indicate that the resistance stress against hot cracking can be improved obviously by addition of Ti, because of its grain refining function. It is also found that, when Ce is added into the alloys, besides its effect in refining crystalline, the mechanical behavior of lower melting point eutectic phase in quasi-solid zone can be improved efficiently by some compounds with Ce formed and deposited between dendrites. Therefore, a colligating effect of Ti and Ce on improving resistance stress against hot cracking is more efficient than that only single alloy element is applied. When hot cracking occurs, grains yield at first, and then crack spreads. Both inter-grain and trans-grain fractures are observed, but the major fracture manner is brittleness.
文摘Scale-up synthesis of sub-micron ZSM-5 molecular sieve in a quasi-solid system was investigated. Compared with traditional hydrothermal synthesis, the synthesis in a quasi-solid system has the advantages of high yield, short crystallization time, low energy consumption as well as low emissions. However, the high solid content in the quasi-solid system can cause the mass and heat transfer problems and make scalable production difficult. In order to solve the problem, we have developed a method for the optimization of the mass and heat transfer. By this method one can vary the flow field in the reactor by changing the stirrer speed. Scale-up synthesis of the sub-micron ZSM-5 molecular sieve in a quasi-solid system was carried out in a 5 L reactor with double propeller-type agitators. The process was investigated with product characterization using X-ray diffraction (XRD) and scanning electron microscopy (SEM) and the flow field information was collected using laser Doppler velocimetry (LDV). The results showed that the flow field patterns can be tuned by using different stirrer speeds, the morphology and size of assynthesized of ZSM-5 can be effectively controlled.
基金Project supported by the National Key R&D Program of China(Grant Nos.2016YFB0100300 and 2016YFB0100100)the National Basic Research Program of China(Grant No.2014CB932300)+2 种基金the Beijing Municipal Science&Technology Commission,China(Grant No.D171100005517001)the Strategic Priority Research Program of the Chinese Academy of Sciences(Grant No.XDA09010000)the National Natural Science Foundation of China(Grant No.51502334)
文摘A novel transparent and soft quasi-solid-state electrolyte (QSSE) was proposed and fabricated, which consists of ionic liquid (PYR14TFSI) and nano-fumed silica. The QSSE demonstrates high ionic conductivity of 4.6× 10-4 S/cm at room temperature and wide electrochemical stability window of over 5 V. The Li-O2 battery using such quasi-solidstate electrolyte exhibits a low charge-discharge overpotential at the first cycle and excellent long-term cyclability over 500 cycles.
基金Project supported in part by the National Natural Science Foundation of China (Grant Nos 60637010 and 60671036)the National Basic Research Program of China (Grant No 2007CB310403)Tianjin Applied Fundamental Research Project (Grant No07JCZDJC05900)
文摘We have made a gain-switched all-solid-state quasi-continuous-wave (QCW) tunable Ti:sapphire laser system, which is pumped by a 532 nm intracavity frequency-doubled Nd:YAG laser. Based on the theory of gain-switching and the study on the influencing factors of the output pulse width, an effective method for obtaining high power and narrow pulse width output is proposed. Through deliberately designing the pump source and the resonator of the Ti:sapphire laser, when the repetition rate is 6 kHz and the length of the cavity is 220 mm, at an incident pump power of 22 W, the tunable Ti:sapphire laser from 700 to 950nm can be achieved. It has a maximum average output power of 5.6W at 800nm and the pulse width of 13.2 ns, giving an optical conversion efficiency of 25.5% from the 532 mn pump laser to the Ti:sapphire laser.
基金supported by the National Natural Science Foundation of China (Nos. 51134022 and 51174203)the Key Project of Chinese National Programs for Fundamental Research and Development (No. 2012CB214904)+2 种基金the National Natural Science Foundation of China for Innovative Research Group (No. 50921002)the Natural Science Foundation of Jiangsu Province (No. BK2010002)the Fundamental Research Funds for the Central Universities (Nos. 2010QNB11 and 2010ZDP01A06)
文摘In order to study the settling mechanism of particles in an air-solid magnetically stabilized fluidized bed(MSFB) for separation,we carried out free settling and quasi-zero settling tests on the tracing particles.The results show that the main resistance forces as the tracing particles settled in an air-solid MSFB were motion resistance force and yield force.The motion resistance and yield forces greatly hindered the free settling of the particles by greatly decreasing the acceleration for settling process of the particles.The acceleration decreased from 3022.62 cm/s 2 to zero in 0.1 s,and in the end,the particles stopped in the air-solid MSFB.The yield force on particles increased with increasing the magnetic field intensity,resulting in decrease of the quasi-zero settling displacement.However,the yield force on particles decreased with increasing the fluidized air velocity,leading to increase of the quasi-zero settling displacement.When the structure and operating parameters of the air-solid MSFB were set up,the yield stress on particles stopped in an air-solid MSFB was a function of diameter and density of particles.The settling displacements of equal diameter particles increased with increasing their densities,and the settling displacements of equal density particles increased with increasing their diameters.
基金Project supported by the National Natural Science Foundation of China (No.50278051)Shanghai Leading Academic Discipline Project (No.Y0103)
文摘Based on convolution-type constitutive equations for linear viscoelastic materials with damage and the hypotheses of Timoshenko beams, the equations governing quasi-static and dynamical behavior of Timoshenko beams with damage were first derived. The quasi-static behavior of the viscoelastic Timoshenko beam under step loading was analyzed and the analytical solution was obtained in the Laplace transformation domain. The deflection and damage curves at different time were obtained by using the numerical inverse transform and the influences of material parameters on the quasi-static behavior of the beam were investigated in detail.