Study of damage behavior and repair effectiveness of patch repaired carbon fiber laminate under quasi-static indentation loading

Damage caused due to low-velocity impacts in composites leads to substantial deterioration in their residual strength and eventually provokes structural failure.This work presents an experimental investigation on the effects of different patch and parent laminate stacking sequences on the enhancement of impact strength of Carbon Fiber Reinforced Polymers(CFRP)composites by utilising the adhesively bonded external patch repair technique.Damage evolution study is also performed with the aid of Acoustic Emission(AE).Two different quasi-isotropic configurations were selected for the parent laminate,viz.,[45°/45°/0°/0°]s and[45°/0°/45°/0°]s.Quasi Static Indentation(QSI)test was performed on both the pristine laminates,and damage areas were detected by using the C-scan inspection technique.Damaged laminates were repaired by using a single-sided patch of two different configurations,viz.,[45°/45°/45°/45°]and[45°/0°/0°/45°],and employing a circular plug to fill the damaged hole.Four different combinations of repaired laminates with two configurations of each parent and patch laminate were produced,which were further subjected to the QSI test.The results reveal the effectiveness of the repair method,as all the repaired laminates show higher impact resistance compared to the respective pristine laminates.Patches of[45°/0°/0°/45°]configuration when repaired by taking[45°/45°/0°/0°]s and[45°/0°/45°/0°]s as parents exhibited 68%and 73%higher peak loads,respectively,than the respective pristine laminates.Furthermore,parent and patch of configuration[45°/0°/45°/0°]s and[45°/0°/0°/45°],respectively,attain the highest peak load,whereas[45°/45°/0°/0°]s and[45°/45°/45°/45°]combinations possess the most gradual decrease in the load.

Analysis of the Application of Static Load Test in Bridge Bearing Capacity Testing

This article uses real engineering projects as examples to analyze how static load test technology is applied in testing the bridge-bearing capacity.The analysis covers aspects such as testing section layout,test load and efficiency coefficient,loading plan,evaluation optimization,test result modification,and result evaluation.The aim is to support the accurate detection and evaluation of bridge-bearing capacity.

California Bearing Ratio for Cohesive Soils from Quasi Static Cone Tests

The California bearing ratio (CBR) test is the most widely spread method of determining the bearing strength of the pavement material and is fundamental to pavement design practice in most countries. This test is expensive, laborious and time consuming, and to overcome this, Quasi static cone penetrometer machine was fabricated and used to measure the consistency limits (liquid limit-LL, Plastic limit-PL and Plasticity index-PI), which were used to develop an empirical equation to determine CBR. Soil samples were collected and unsoaked CBR, PL, LL and PI were determined according to BS 1377 part 9 and BS 1377-2;1990. Quasi static penetration forces at 20 mm depth of penetration were also determined at consistency limits. It was found that the force of 1020 gf and 60 gf was achieved at a depth of 20 mm at PI and LL respectively. The correlation and regression analysis between consistency limits, and the experimental CBR obtained showed coefficient of determination, R2 = 0.907 between CBR and all the parameters using multiple linear regression analysis (MLRA). The regression equation developed was used together with the relationship developed between the Quasi static Penetration force at consistency limits and the tested consistency limits to come up with the General Empirical Equation. Verification of the formula showed that the correlation can be used accurately to determine the un soaked CBR.

Seismic performance evaluation of an infilled rocking wall frame structure through quasi-static cyclic testing

Earthquake investigations have illustrated that even code-compliant reinforced concrete frames may suffer from soft-story mechanism.This damage mode results in poor ductility and limited energy dissipation.Continuous components offer alternatives that may avoid such failures.A novel infilled rocking wall frame system is proposed that takes advantage of continuous component and rocking characteristics.Previous studies have investigated similar systems that combine a reinforced concrete frame and a wall with rocking behavior used.However,a large-scale experimental study of a reinforced concrete frame combined with a rocking wall has not been reported.In this study,a seismic performance evaluation of the newly proposed infilled rocking wall frame structure was conducted through quasi-static cyclic testing.Critical joints were designed and verified.Numerical models were established and calibrated to estimate frame shear forces.The results evaluation demonstrate that an infilled rocking wall frame can effectively avoid soft-story mechanisms.Capacity and initial stiffness are greatly improved and self-centering behavior is achieved with the help of the infilled rocking wall.Drift distribution becomes more uniform with height.Concrete cracks and damage occurs in desired areas.The infilled rocking wall frame offers a promising approach to achieving seismic resilience.

Technical Analysis of Highway Bridge Static Load Test

Highway bridges are an important part of the transportation industry and can promote social economic construction and development.In actual operation,highway bridges are often damaged due to overload and natural factors,which tend to affect the safety and shorten the service life of these bridges.Assessing the overall state and performance of highway bridges is therefore a key element.Static load test,which is a type of sustainable detection experiment,has many advantages,including low cost,high efficiency,and high accuracy.In this paper,the bridge structure is analyzed through the application of theoretical calculations and relevant comparisons,so as to judge the operating state of the bridge.

Static Load Test Detection of Continuous Rigid- Frame Railway Bridge

The quality of the continuous rigid-frame railway bridge is related to the safety of train operation,so it is necessary to test its stiffness,strength,and other indicators.Static load test is a common technique for bridge inspection.This article summarizes the purpose of the static load test for a continuous rigid-frame railway bridge,including the required equipment,operation methods,etc.,and lists examples to analyze the operation process and precautions of static load test,hoping to provide reference information for relevant personnel.

Mechanical properties and supporting effect of CRLD bolts under static pull test conditions

A device for supporting soft rock masses combined with a constant resistance structure characterized by constant resistance and large deformation at the end of a steel bar, known as the constant resistance and large deformation（CRLD） bolt, has recently been developed to counteract soft rock swelling that often occurs during deep mining. In order to further study the mechanical properties of the CRLD bolt, we investigated its mechanical properties by comparison with the conventional strength bolt（rebar） using static pull tests on many aspects, including supporting capacity, elongation, radial deformation, and energy absorption. The tests verified that the mechanical defects of the rebar, which include the decrease of bolt diameter, reduction of supporting capacity, and emergence and evolution of fracture until failure during the whole pull process, were caused by the Poisson＇s ratio effect. Due to the special structure set on the CRLD bolt, the bolt presents a seemingly unusual phenomenon of the negative Poisson＇s ratio effect, i.e., the diameter of the constant resistance structure increases while under-pulling. It is the very effect that ensures the extraordinary mechanical properties, including high resistance, large elongation, and strong energy absorption. According to the comparison and analysis of numerical simulation and field test, we can conclude that the CRLD bolt works better than the rebar bolt.

Application of bi-directional static loading test to deep foundations

Bi-directional static loading test adopting load cells is widely used around the world at present, with increase in diameter and length of deep foundations. In this paper, a new simple conversion method to predict the equivalent pile head load-settlement curve considering elastic shortening of deep foundation was put forward according to the load transfer mechanism. The proposed conversion method was applied to root caisson foundation in a bridge and to large diameter pipe piles in a sea wind power plant. Some new load cells, test procedure, and construction technology were adopted based on the applications to different deep foundations, which could enlarge the application scopes of bi-directional loading test. A new type of bi-directional loading test for pipe pile was conducted, in which the load cell was installed and loaded after the pipe pile with special connector has been set up. Unlike the conventional bi-directional loading test, the load cell can be reused and shows an evident economic benefit.

Quasi-static Analysis of Thrust-loaded Angular Contact Ball Bearings Part Ⅰ:Theoretical Formulation

Ball bearings play an important role in various rotating machineries,but the complicated kinematic and tribological features of ball bearings make many aspects of their operating behaviors still inconclusive.Most theoretical analyses of ball bearings up to date are based on either the hypothesis of race control or other empirical models to determine the ball motion of ball bearings,but none of these strategies can reveal and consequently employ the intrinsic coupling mechanism between the spin and the tangential traction of contacting bodies rolling upon one another.To remedy the deficiency of current analytical models for ball bearing analysis,the rolling contact theory is employed to establish an explicit link between motions and interactions within ball bearings.A differential slip model is established to precisely define the slip component due to the significant curvature of the common contact patches between the ball and inner/outer raceways.The creepage and the spin ratio are formulated to accurately define the relative rigid motion between the ball and the inner/outer raceway.Then a quasi-static analytical model is established that can accurately determine the motions of the balls and races of the ball bearing.It can also give a vivid description of the slip and traction distributions within the contact area.The analytical model can be effectively used to analyze the operational conditions and tribological features of solid-lubricated ball bearings.It can also be used optimize the construction of ball bearings for specific applications.

Theoretical research and experimental validation of quasi-static load spectra on bogie frame structures of high-speed trains

One of the major problems in structural fatigue life analysis is establishing structural load spectra under actual operating conditions.This study conducts theoretical research and experimental validation of quasi-static load spectra on bogie frame structures of high-speed trains.The quasistatic load series that corresponds to quasi-static deformation modes are identified according to the structural form and bearing conditions of high-speed train bogie frames.Moreover,a force-measuring frame is designed and manufactured based on the quasi-static load series.The load decoupling model of the quasi-static load series is then established via calibration tests.Quasi-static load–time histories,together with online tests and decoupling analysis,are obtained for the intermediate range of the Beijing—Shanghai dedicated passenger line.The damage consistency calibration of the quasi-static discrete load spectra is performed according to a damage consistency criterion and a genetic algorithm.The calibrated damage that corresponds with the quasi-static discrete load spectra satisfies the safety requirements of bogie frames.

Research on Dynamic and Static Test Methods for Evaluating the Poisson's Ratio of Orien ted Strand Board

In this article,dynamic method and static method of testing Poisson's ratio of OSB(Oriented Strand Board)were proposed.Through modal and static numerical analyses,the position where the transverse stress is equal to zero was determined.The binary linear regression method was applied to express the gluing position of the strain gauge as a relational express ion that depended on the length-width ratio and width-thickness ratio of the canti-lever plate.Then the longitudinal and transverse Poisson's ratios of OSB were mea sured by the given dynamic and static methods.In addition,the test results of OSB Poisson's ratio were analyzed with the probability distribution of random variables.The results showed that using the proposed dynamic method and static method,the test results for longitudinal and transverse Poisson's ratios of OSB were quite consistent,despite the gluing position of the strain gauges being different.And these OSB Poisson's ratios were accorded with that obtained by the axial tensile method and the four-point bending method.OSB longitudinal and transverse Poisson's ratios followed Weibull distribution.

Quasi-static Analysis of Thrust-loaded Angular Contact Ball Bearings Part Ⅱ:Results and Discussion

Ball bearings are widely employed mechanical components characterized by high precision and quality,and usually play important roles in various rotary machines and mechanisms.Many advanced applications require a deep understanding of their various kinematic and tribological characteristics that are essential to predict the fatigue endurance,relieve the vibration and minimize the power dissipation of ball bearings in particular applications.An angular contact ball bearing under a specified operating condition is simulated with the quasi-static/creepage analytical model proposed in the preceding article.The results demonstrate that the ball bearing is a statically determinate system.That the balls spin on both inner and outer races means the ball is controlled by neither the inner nor the outer raceway.The friction between the ball and raceway renders the inner and outer contact angles unequal.The larger the coefficient of friction is,the larger the angle deviation.The tangential traction perpendicular to the rolling direction due to the spin induces a gyro-like rotation of the ball with respect to the raceway even if no inertial effects are considered.The tangential elastic compliance of contacting surfaces gives rise to locked areas within the contact patch and transforms the sliding lines from circles into spirals.The differential slip due to the close conformity of the ball and raceway makes the sliding and traction distributions asymmetric,which will influence the location of the spinning center of the ball with respect to the raceway.The quasi-static/creepage model can be used to reveal the operating behaviors of ball bearings running under steady conditions and to optimize the design of ball bearings for specific applications.

Structural damage identification using test static data based on grey system theory

A new structural damage identification method using limited test static displacement based on grey system theory is proposed in this paper. The grey relation coefficient of displacement curvature is defined and used to locate damage in the structure, and an iterative estimation scheme for solving nonlinear optimization programming problems based on the quadratic programming technique is used to identify the damage magnitude. A numerical example of a cantilever beam with single or multiple damages is used to examine the capability of the proposed grey-theory-based method to localize and identify damages. The factors of meas-urement noise and incomplete test data are also discussed. The numerical results showed that the damage in the structure can be localized correctly through using the grey-related coefficient of displacement curvature, and the damage magnitude can be iden-tified with a high degree of accuracy, regardless of the number of measured displacement nodes. This proposed method only requires limited static test data, which is easily available in practice, and has wide applications in structural damage detection.

Theoretical analysis on quasi-static lateral compression of elliptical tube between two rigid plates

Based on the rigid plastic theory; the load-deflection functions with and without considering the effect of strain hardening are respectively derived for an elliptical tube under quasi-static compression by two parallel rigid plates. The non-dimensional load-deflection responses predicted by the present theory and the finite element simula- tions are compared, and the favorable agreement is found. The results show that strain hardening may have a noticeable influence on the load-deflection curves of an elliptical tube under quasi-static compression. Compared with the circular counterpart, the ellip- tical tube exhibits different energy absorption behavior due to the difference between the major axis and the minor axis. When loaded along the major axis of a slightly oval tube, a relative even and long plateau region of the load-deflection curve is achieved, which is especially desirable for the design of energy absorbers.

Static load test and load transfer mechanism study of squeezed branch and plate pile in collapsible loess foundation

As a special geological phenomenon, the character of collapsible loess foundation is collapsible when penetrated by water. This character leads to the soil losing load bearing capacity largely and may lead to foundation failure. Pile is a popular foundation used in collapsible loess. The squeezed branch and plate pile is a new type of pile developed in recent years and has not be used in a project before. In this paper three squeezed branch and plate piles are tested in collapsible loess after immersion processing. The results may be used for reference in similar construction project, and to provide theoretical references for de- signing of the squeezed branch and plate piles in engineering practice.

Failure behavior of highly stressed rocks under quasi-static and intensive unloading conditions

Unloading failure of rocks,especially highly stressed rocks,is one of the key issues in construction of underground structures.Based on this,analytical models for rocks under quasi-static and intensive unloading conditions are established to study the failure behavior of highly stressed rocks.In case of rock failure under quasi-static unloading,the rock mass ahead of working face is regarded as an elasto-brittle material,and the stress-displacement curves are used to characterize the tensile fracture of peak-stress area.It is observed that,when intensive unloading happens,there is an elastic unloading wave（perturbation wave） propagating in the rock mass.If the initial stress exceeds the critical stress,there will be a fracture wave,following the elastic unloading wave.To study the propagation feature of fracture wave,the conservation laws of mass,momentum and energy are employed.Results show that the post-peak deformation,strength and energy dissipation are essential to the failure process of highly stressed rocks.

The quasi－static solutions of two kinds of the thermo－elastic problem and the time spacedistributionfeatureoftheseismicprecursorfields

The stress field, controlling the developmental process of a shallow focus inland earthquake, is regarded as the superposition of the fundamental and the variational stress field, but the latter often plays an important role. In this paper we focus on two kinds of problems generating the variational stress field, which is related to geotherm. One is the local high temperature region problem, which includes the situations of the heat carrying fluid intruding into the vertical or horizontal cracks and the case of existence of the static state local high temperature region. The other is the problem that the thermal energy is released as the fault emerges displacement discontinuities,during the steady state extension. The two problems can be idealized into the three dimension thermoelastic quasi static problems and their solutions can be given, respectively. Thereby,we may obtain the approximate expressions of some additional seismic precursor fields generated on the plane near the ground surface,for examples, the temperature, the body strain and the underground water, the vertical deformation and the ground tilt vector fields etc. We discuss their space time distribution feature on the plane and get some qualitative results by contrasting them with each other. lt may provide some clues for further studying the comprehensive applications of the preseismic observations.

Fuzzy Model Free Adaptive Control for Rotor Blade Full-Scale Static Testing

To eliminate the node traction coupling during wind turbine blade full-scale static testing,a model free adaptive control algorithm is presented based on fuzzy control performance function compensation. Based on the universal model theory,the fuzzy model free adaptive control( FMFAC) algorithm is designed by configuring the spot static testing experiences as compensation function F( ·). Then the algorithm implementation process is provided and its quick convergence is proved. Using software to establish static load coupling model of multi-nodes,simulate and verify the validity of FMFAC algorithm,which is applied to wind turbines blade full-scale static testing. The results show that the adaptive decoupling ability of FMFAC is better. The traction of four load points can stay steady and change coordinately. Process error is not over ± 6 k N. The error rate is lower than 1% in special phase.This algorithm effectively eliminates the traction coupling of the static testing process,and makes wind turbine blade testing steadily.

Effects of Microstructure on Quasi⁃Static Transverse Loading Behavior of 3D Circular Braided Composite Tubes

The effects of microstructure on quasi-static transverse loading behavior of 3D circular braided composite tubes were studied. Transverse loading tests were conducted. Transverse load-deflection curves were obtained to analyze the effects of braiding parameters including the braiding angle, the wall thickness, and the diameter on the transverse loading of 3D circular braided composite tubes. Breaking loads, moduli and strengths had also been used to describe the transverse loading behaviors. The failure morphologies were shown to reveal damage mechanisms. From the results, the increase in braiding angle, wall thickness and diameter increases the ability of anti-deformation and breaking load of braided tubes. The breaking load of specimen with a braiding angle of 45° is about 1.68 times that of specimen with a braiding angle of 15°. The breaking load of specimen with 4 layers of yarns is about 2.15 times that of specimen with 2 layers of yarns. The breaking load of the tube with a diameter of 25.5 mm is about 2.39 times that of the tube with a diameter of 20.5 mm.