Rotating arc horizontal narrow gap welding of high strength quenched and tempered steel

Rotating arc borizontal narrow gap welding of quenched ＆ tempered （Q＆T） steel was innovatively performed for solving the bottleneck that the molten pool sagged due to the gravity. The shapely multilayer single pass horizontal joint could be obtairzed by using the rotating are welding process. The cold crack was not observed in the joint without controlling the heat input and selecting the consumables intentionally. Microstructure of the joint could be divided into three zones： base metal zone （BMZ） , heat-affected zone （ HAZ） and weld zone （WZ）. Because of the characteristic of the rotating arc horizontal welding process, the defects in the joints were slag inclztsion formed at the interlayer of lower side wall. Tbe tensile strength and hardness of HAZ and WZ were larger than those of BMZ. The impact toughness in WZ, HAZ and BM at 0 % is equal to 11.5, 212 and 236 J, respectively.

Cold Cracking of Flux Cored Arc Welded Armour Grade High Strength Steel Weldments

In this investigation, an attempt has been made to study the influence of welding consumables on the factors that influence cold cracking of armour grade quenched and tempered （Q＆.T） steel welds. Flux cored arc welding （FCAW） process were used making welds using austenitic stainless steel （ASS） and low hydrogen ferritic steel （LHF） consumables. The diffusible hydrogen levels in the weld metal of the ASS and LHF consumables were determined by mercury method. Residual stresses were evaluated using X-ray stress analyzer and implant test was carried out to study the cold cracking of the welds. Results indicate that ASS welds offer a greater resistance to cold cracking of armour grade Q＆T steel welds.

Experimental Investigation on the Performance of Armour Grade Q&T Steel Joints Fabricated by Flux Cored Arc Welding with Low Hydrogen Ferritic Consumables

Quenched and Tempered （Q＆T） steels are widely used in the construction of military vehicles due to its high strength to weight ratio and high hardness. These steels are prone to hydrogen induced cracking （HIC） and softening in the heat affected zone （HAZ） after welding. The use of austenitic stainless steel （ASS） consumables to weld the above steel was the only available remedy to avoid HIC because of higher solubility for hydrogen in austenitic phase. Recent studies revealed that low hydrogen ferritic （LHF） steel consumables can also be used to weld Q＆T steels, which can give very low hydrogen levels in the weld deposits and required resistance against cold cracking. Hence, in this investigation an attempt has been made to study the performance of armour grade Q＆T steel joints fabricated by flux cored arc welding with LHF steel consumables. Two different consumables namely （i） austenitic stainless steel and （ii） low hydrogen ferritic steel have been used to fabricate the joints by flux cored arc welding （FCAW） process. The joints fabricated by LHF consumable exhibited superior transverse tensile properties due to the presence of ferrite microstructure in weld metal. The joints fabricated by ASS consumable showed higher impact toughness due to the presence of austenitic phase in weld metal microstructure. The HAZ softening in coarse grain heat affected zone （CGHAZ） is less in the joints fabricated using LHF consumable due to the lower heat input involved during fabrication compared to the joints fabricated using ASS consumables.

Microstructural analysis of the softened zone in the welding joint of 100 kg class hot-rolled extra-high-strength steel

Using the Gleeble 3500 thermal-mechanical system to simulate thermal cycles with different peak temperatures, the hardness and microstructure in the heat-affected zones of two kinds of 100 kg class hot-rolled extra-high-strength steel were compared. When the peak temperature of the thermal cycle was 800℃ ,incomplete transformation occurred during quenching in both steels, and massive martensite and bainite grains were formed. The hardness was determined by the composition and distribution of the microstructure. The concentration of massive martensite was low, and hence the hardness was low,in steel #1. Conversely,the massive martensite content in steel #2 was high and uniformly distributed,resulting in a high hardness. These findings can provide a reference for improving the mechanical properties in the softened zone.