Numerical simulation research of dimension variation in heavy plate during quenching and tempering process

The dimension variation of B610E steel during the quenching and tempering process was simulated by ABAQUS,the coefficient of heat transfer during quenching was verified by the buried thermocouple test and the trend of the dimension variation during the quenching process was also calculated by ABAQUS. It was shown by the comparison of simulated results and industrially measured results that only the simulation of thickness and width variation was accurate, while length variation needed further simulation. Besides, the dimension variation trend was identical with the measured results.

Effect of quenching and tempering processes on properties and microstructure of G115 steel

The novel martensitic heat-resistant steel G115 was designed for thick-section boiler components of ultra-supercritical(USC) power plants at 630-650 ℃.The impact of the quenching and tempering processes on the properties and microstructure of G115 steel was explored.The samples that were quenched and tempered twice had a higher tensile strength at room temperature and 650 ℃,and the impact energy was significantly improved.The strength and impact energy increased in proportion to the increase in the first quenching temperature.The microstructure differences between the single and double quenched and tempered samples were examined using metallographic microscopy and scanning electron microscopy.The grain size of the double quenched and tempered samples was finer than that of the single quenched and tempered samples, and the tempered martensite lath is more visible, as are the carbides and other precipitates, which are finer and more uniformly distributed.As the first quenching temperature increased, the grains became coarser but more uniform.

Application of the Controllable Quenching Technology to the Quenching and tempering Workpieces

In order to obtain the desired mechanical properties of quenching and tempering workpieces, as well as reduce the cracking tendency and distortion, a program of controllable quenching was established. Furthermore, a computer-aided quenching system (CAQ) was also developed. The application samples of the CAQ system showed satisfactory results.

Analysis of microstructure and performance of temper bead welded joints for SA508-3 steel by Quenching and Tempering mode

The HAZ microstructure and performance of Quenching and Tempering mode temper bead welding and general welded joints which were made on SA508-3 steel of 60 mm thickness were compared in this article. The result shows that tempering sorbite which has excellent overall performance was obtained in both modes. The microstructure of Quenching and Tempering mode welded joints got more fine grain. Even though the hardness of tempering bead welded joints is higher than the general one,it still meets the standards which is lower than 350 HV. The impact absorbing energy of each district of tempering bead welded joints HAZ reached 170 J,which is equal to general one.

Cold extrusion deformation behavior of medium carbon steel after quenching and tempering

By taking 40Cr as a specific object, cold extrusion deformation behavior of medium carbon steel after quenching and tempering was studied by experimental works. The influence of deformation extent (10%-50%), cone angle of die (90 °-120 °), hardness after quenching and tempering (HRC21-29) and lubricated condition on the forming load was analyzed. The results show that there is no central bursting and micro crack in the inner of the extruded specimen, and the forming quality is good. The double-peak phenomenon takes place at the front-end of the specimen; the double-peak index increases with deformation extent, and larger deformation can avoid the double-peak phenomenon. The deformation extent is the most important influencing factor, and the lubricated condition almost has no influence, which means that the phosphate coating plus soap process is still a proper lubrication method for cold extrusion of medium carbon steel after quenching and tempering. By investigating the microscopic structure before and after deformation, the initial equiaxed grain is elongated in the extrusion direction, and this feature is more significant at the front-end of specimen.

Design of Quenching Process for Large-sized AISI P20 Steel Block Used as Plastic Die

For large-sized AISI P20 steel block used as plastic die with a thickness of more than 200 mm, appropriate quenching processes are the key to obtain much thick hardened layer. In this paper, different quenching processes of AISI P20 steel block such as oil quenching, direct water quenching, water quenching with precooling and water quenching with pre-cooling and self-tempering were numerically investigated by computer simulation based on the detailed discussion on the mathematical models of quenching processes including partial differential equations of heat transfer, thermal physical properties, latent heat, heat transfer coefficient and calculation of phase transformation, The results show that the water quenching with pre-cooling and self-tempering process can not only effectively avoid quenching cracks, but also obtain deeper harden depth than oil quenching.

Effect of supply voltage and body-biasing on single-event transient pulse quenching in bulk fin field-effect-transistor process

Charge sharing is becoming an important topic as the feature size scales down in fin field-effect-transistor （FinFET） technology. However, the studies of charge sharing induced single-event transient （SET） pulse quenching with bulk FinFET are reported seldomly. Using three-dimensional technology computer aided design （3DTCAD） mixed-mode simulations, the effects of supply voltage and body-biasing on SET pulse quenching are investigated for the first time in bulk FinFET process. Research results indicate that due to an enhanced charge sharing effect, the propagating SET pulse width decreases with reducing supply voltage. Moreover, compared with reverse body-biasing （RBB）, the circuit with forward body-biasing （FBB） is vulnerable to charge sharing and can effectively mitigate the propagating SET pulse width up to 53% at least. This can provide guidance for radiation-hardened bulk FinFET technology especially in low power and high performance applications.

Instrumented oscillographic study on impact toughness of an axle steel DZ2 with different tempering temperatures

Compared with the conventional Charpy impact test method,the oscillographic impact test can help in the behavioral analysis of materials during the fracture process.In this study,the trade-off relationship between the strength and toughness of a DZ2 axle steel at various tempering temperatures and the cause of the improvement in impact toughness was evaluated.The tempering process dramatically influenced carbide precipitation behavior,which resulted in different aspect ratios of carbides.Impact toughness improved along with the rise in tempering temperature mainly due to the increase in energy required in impact crack propagation.The characteristics of the impact crack propagation process were studied through a comprehensive analysis of stress distribution,oscilloscopic impact statistics,fracture morphology,and carbide morphology.The poor impact toughness of low-tempering-temperature specimens was attributed to the increased number of stress concentration points caused by carbide morphology in the small plastic zone during the propagation process,which resulted in a mixed distribution of brittle and ductile fractures on the fracture surface.

Effects of Quenching Process on Microstructure and Mechanical Properties of Low Carbon Nb-Ti Microalloyed Steel

The low carbon Nb-Ti mieroalloyed tested steel was prepared by the process of vacuum induction furnace smelting, forging and hot rolling. The new steel aims to meet the demand of high strength, high toughness and high plasticity for building facilities. The effects of quenching process on microstructure and mechanical properties of tested steel were investigated. The results showed that prior austenite grain size, phase type and precipitation behavior of （ Nb, Ti） （ C, N） play important roles in mechanical properties of the steel. Through modified appropriately, the model of austenite grain growth during heating and holding is d^5.7778 = 5. 6478^5.7778 ＋ 7.04 × 10^22t^1.6136 exp（- 427. 15 ×10^3 /（RT））. The grain growth activation energy is Qg = 427. 15 kJ. During quenching, the microscopic structures are mainly martensite and lath bainite which contains lots of lath substructure and dislocations. The content of phases, fine and coarsening （ Nb, Ti ） （ C, N ） precipitated changes during different quenching temperatures and holding time. Finally compared with the hardness value, the best quenching process can be obtained that heating temperature and holding time are 900 ℃ and 50 mins, respectively.

Numerical and experimental analysis of quenching process for cam manufacturing

In order to obtain satisfactory mechanical properties for the cam used in high-power ship diesel engines, a new quenching technology was proposed by designing a two-stage quenching process with an alkaline bath as the quenching medium. To demonstrate the effectiveness of the proposed new quenching technology, both numerical analysis and experimental study were performed. The new quenching technology was analyzed using finite element method. The combined effects of the temperature, stress and microstructure fields were investigated considering nonlinear material properties. Finally, an experimental study was performed to verify the effectiveness of the proposed new quenching technology. The numerical results show that internal stress is affected by both thermal stress and transformation stress. In addition, the direction of the internal stress is changed several times due to thermal interaction and microstructure evolution during the quenching process. The experimental results show that the proposed new quenching technology significantly improves the mechanical properties and microstructures of the cam. The tensile strength, the impact resistance and the hardness value of the cam by the proposed new quenching technology are improved by 4.3%, 8.9% and 3.5% compared with those by the traditional quenching technology. Moreover, the residual stress and cam shape deformation are reduced by 40.0% and 48.9% respectively for the cam manufactured by the new quenching technology.

Structure and electrochemical properties of hypo-stoichiometric hydro-gen storage alloys prepared by twin-roller rapid quenching process

The stoichiometric alloy MlB5.0 and the hypo-stoichiometric alloy MlB4.85 were prepared by twin-roller rapid quenching process, and their structure and electrochemical properties were studied. The results of XRD show that both of the alloys have a typical single-phase hexagonal CaCus-type structure. The cell volume of the hylpo-stoichiometric alloy M1B4.85 is slightly larger than that of the stoichiometric alloy M1B5.0, although its lattice constant cla is smaller. Under 2 C discharging rate, i.e. 640 mA/g, the M1B4.85 has a discharge capacity of 320 mAh/g, which is higher than that of the M1Bs.o, 312 mAh/g. Nevertheless, the capacities of the M1B4.85 and the M1Bs.o decline 24.7% and 20.2% after 400 cycles, respectively. The relationship of electrochemical performances of the alloys with their structures is discussed.

Finite element simulation and microstructure of two-pass inner spinning process of curved-generatrix cone cylindrical parts with annealing/quenching

A two-pass annealing/quenching internal spinning process with small-end rotations is proposed to form a curved generatrix conical thin-walled shell.That is,annealing at 360°C for 2 h followed by the 1st pass spinning,and finally quenching in ice water after holding for 1 h at 498°C followed by the 2nd pass spinning.ABAQUS finite element software is used to simulate the internal spinning process of the products formed under different forming parameters.The distribution laws of spinning force,the stress and strain under different forming processes were compared and analyzed.The mechanical properties and microstructure of the products are subsequently analyzed.The results show that the strain and the residual stress in the skin area of the formed products under two-pass spinning process more uniform,and the hardness and the mechanical performance are improved.The microstructure of the products formed with the 0.15 mm thickness reduction at the 2nd pass is excellent.And the second phase grain size distributed uniformly in the range of 36μm.Whereas,the second phase particles are broken seriously and the size distribution inhomogeneity is increased when the thickness reduction in the skin area is greater than 0.20 mm at the 2nd pass spinning process.

A New Quenching Process and Tower to Improve the Recovery of Acrylonitrile

Quenching process and design of the quenching tower in acrylonitrile production in China were studied in order to decrease the polymerization loss of acrylonitrile in the quenching tower. Based on the research of acrylonitrile polymerization in the quenching tower, a new quenching process was proposed to avoid the disadvantages of the original process. Two kinds of internals were installed to improve the performance of the quenching tower. Through a series of air-flow and real-flow model experiments, the new quenching process and new design were showed to be successful in enhancing the mass and heat transfer in the vapor-liquid system and decreasing the loss of acrylonitrile.Industrial application showed satisfactory results of decrease of the acrylonitrile loss in the quenching tower by about 4.5% and increase of the acrylonitrile recovery of the whole plant by more than 4%.

Component modification of steel slag in air quenching process to improve grindability

A new solution called component modification in-process was introduced to the difficult grinding of air quenching steel slag by a series of experiments. The results show that the fly ash added into the molten steel slag before air quenching can more effectively improve the slag's grindability than milltailings, which is the other modification agent tested under the same conditions. The role of fly ash is strengthened as its proportion increases, although the degree of promotion is gradually reduced. As a result of the reaction between fly ash and steel slag at high temperature, some new mineral phases and vitreous bodies with fine grindability promote the slag grinding easily. This work is helpful to making a comprehensive utilization of steel slag and maximize its economic efficiency in China.

CFD simulations of quenching process for partial oxidation of methane:Comparison of jet-in-cross-flow and impinging flow configurations

A new quenching process using the cold pyrolysis gas has been proposed for the partial oxidation(POX) of methane to recover the heat. The mixing of hot product gas and cold pyrolysis gas in milliseconds is critical to this new approach. Two most widely-used rapid mixing configurations, i.e. the jet-in-cross-flow(JICF) and impinging flow configurations, are compared in terms of mixing and quenching performances using computational fluid dynamics(CFD) coupled with detailed reaction mechanism Leeds 1.5. The mixedness, residence time distribution, temperature decreasing rate and loss ratio of acetylene during the quenching are systematically studied. The results show that the impinging flow has a more uniform mixing and narrower residence time distribution than the JICF.However, the temperature decreasing rate of the mainstream is faster in the JICF than in the impinging flow. The loss ratio of acetylene in the quenching process is 2.89% for the JICF and 1.45% for the impinging flow, showing that the impinging flow configuration is better and feasible for the quenching of POX of methane.

Effect of induction heating and tempering on properties and microstructures of quenched and tempered pipes

In this study,a C-Mn quenched steel tube was quickly tempered by induction heating,and the influence of the tempering temperature on its performance was studied and compared with that by traditional tempering. The results show that the yield strength of both is quite strong with regular changes in the tempering temperature,but that the tensile strength of the tube tempered by induction heating is higher than that tempered by traditional tempering by about 25 MPa,and the elongation after induction tempering is significantly higher than that after traditional tempering. The differences in the microstructures of tubes after induction and traditional tempering were compared by metallographic microscope,scanning electron microscopy,and transmission electron microscopy.Theoretical analysis was also performed. Compared with traditional tempering,a fine dispersion of precipitated carbides occurs after induction tempering,which is the main reason for the performance differences.

Flame quenching process in cavity based on model scramjet combustor

The flame quenching process in combustors was observed by high speed camera and Schlieren system, at the inflow conditions of Ma = 2.64, To = 1483K, P0 = 1.65 MPa, T = 724 K and P -- 76.3 kPa. Changing process of the flame and shock structure in the combustor was clearly observed. The results revealed that the precom- bustion shock disappeared accompanied with the process in which the flame was blown out and withdrawed from the mainflow into the cavity and vanished after a short while. The time of quenching process was extended by the cavity flame holder, and the ability of flame holding was enhanced by arranging more cavities in the downstream as well. The flame was blown from the upstream to the downstream, so the flame in the downstream of the cavity was quenched out later than that in the upstream.

Design of Industrial Quenching Processes

The method of designing industrial processes of quench cooling, in particular, the speed of the conveyor movement with regard to shape and sizes of parts to be quenched, thermal and physical properties of material and cooling capacity of quenchants has been developed. The suggested designing method and databases are the basis for the complete automation of industrial processes of quench cooling, especially for continuous conveyor lines, with the purpose of making high-strength materials. The process is controlled by infrared technique.

An Internal State Variable Model for the Low Temperature Tempering of Low Alloy Steels

An internal state variable (ISV) framework is used to predict the rate and degree of strain relaxation associated with the stage I, low temperature tempering of martensite. A single variable tracks the change in volume between the tempered an untempered structures. The rate at which this occurs is taken to be a function of martensite fraction, temperature, degree of tempering, and carbon concentration. Experimental dilatometty data is used to both fit and validate the model.

Effect of tempering temperature on microstructure and mechanical properties of high boron white cast iron

The effect of different tempering temperatures on the microstructure and mechanical properties of airquenched high boron white cast iron was studied.The results indicate that the high boron white cast iron comprises dendritic matrix and inter-dendritic M 2 B boride;and the matrix comprises martensite and pearlite.After quenching in the air,the matrix is changed into lath martensite;but only 1-μm-size second phase exists in the matrix.After tempering,another second phase of several tens of nanometers is found in the matrix,and the size and quantity increase with an increase in tempering temperature.The two kinds of second precipitation phase with different sizes in the matrix have the same chemical formula,but their forming stages are different.The precipitation phase with larger size forms during the austenitizing process,while the precipitation phase with smaller size forms during the tempering process.When tempered at different temperatures after quenching,the hardness decreases with an increase in the tempering temperature,but it increases a little at 450 ℃ due to the precipitation strengthening effect of the second phase,and it decreases greatly due to the martensite decomposition above 450 ℃.The impact toughness increases a little when tempered below 300 ℃,but it then decreases continuously owing to the increase in size and quantity of the secondary precipitate above 300 ℃.Considered comprehensively,the optimum tempering temperature is suggested at 300 ℃ to obtain a good combination of hardness and toughness.