Effects of quenching temperature on microstructure and mechanical properties of H13 mandrel steel

Optical microscope, stereomicroscope, scanning electronic microscope （SEM） and mechanical property testing were used to research the effects of different quenching temperatures on the microstructure and mechanical properties of the H13 mandrel steel. The results indicate that following an increase in the quenching ,the degree of alloying is enhanced due to the carbides dissolving gradually in austenite, which improves the hardenability of the specimens, as well as their room and high-temperature strength. At the same time, the fracture toughness increases due to the increment of the martensite number and the interparticle distance of impact toughness. Optimal performance Consequently,the service life of the H13 the carbides. However, extremely coarse grain and martensite can decrease the can be obtained after quenching at 1 060℃ and double tempering at 620℃mandrel steel is extended significantly.

Effect of quenching temperature on the microstructure of Si-containing steel during quenching and partitioning

This study aims to investigate the effect of the 1-step quenching and partitioning （Q＆P） process on the microstructure and the resulting Vicker＇ s hardness of 0.3C-1.5Si-1.5Mn steel by using in-situ dilatometry ,optical microscopy （ OM ）, scanning electron microscopy （ SEM ）, X-ray diffractometry （ XRD ）, and Vicker ＇ s hardness measurement. Systematic analyses indicate that the microstructure of the specimens quenched and partitioned at 150℃ ,200 ℃ ,250℃ ,and 300℃ mainly comprises lath martensite and retained austenite. The dilatometry curve of the specimen partitioned at 150℃ is presumably ascribed to the formation of isothermal martensite. In the early stages of partitioning at 200℃,the nearly unchanged dilatation curve is closely related to the synergistic effect of isothermal martensite formation and transitional epsilon carbide precipitation. In the later stages of partitioning at 200 ℃ ,the slight increase in the dilatation curve is due to the continuous isothermal martensite formation. With further increase in partitioning temperature to 250℃, the dilatation increases gradually up to 3600 s, which is related to carbon partitioning and lower bainite formation. Partitioning at a higher temperature of 300 ℃ causes a rapid increase in the dilatation curve during the initial stages, which subsequently levels off upon prolonging the partitioning time. This is mainly attributed to the rapid diffusion of carbon from athermal martensite to retained austenite and continuous formation of lower bainite.

Low-frequency Internal Friction Behaviour of Zr55Al10Ni5Cu30 Metallic Glass with Different Quenching Temperatures

The correlation between the internal friction behaviour of Zr55 Al10 Ni5 Cu30 BMG samples and their quenching temperatures was investigated. It was found that, below the glass transition temperature, the activation energy decreased with increasing quenching temperature, but in the surpercooled liquid region the activation energy tended to be enhanced with a further increase in the quenching temperature. Besides, there were both anelastic and viscoelastic relaxation for the amorphous alloys. The anelastic behaviour would change into viscoelastic relaxation easily for the samples prepared at higher temperature.

Chemical patterning enhanced by increasing quenching temperature in a medium-Mn steel

Chemical heterogeneity in high-temperature austenite is an effective way to tune the austenite-to-martensite transformation during cooling.The effect of quenching temperature on microstructure evolution is investigated when the high-temperature austenite is heterogeneous.After fast austenitization from partitioned pearlite consisting of Mn-enriched cementite and Mn-depleted ferrite in Fe-0.29C-3.76Mn-1.50Si(wt.%)steel,quenching to room temperature and quenching to 130℃ followed by 400℃ partitioning are both applied.With increasing quenching temperature from 25 to 130℃,the amount of heterogeneous microstructure(lamellar ghost pearlite)increases from 10.6%to 33.6% and the thickness of Mn-enriched retained austenite film is increased from 31.9±5.9 to 51.5±4.4 nm,indicating an enhancement of chemical patterning.It is probably ascribed to the reduction in driving force for austenite-to-martensite transformation,which requires a lower Mn content for austenite retention.

Influence of two distinct quenching end-temperatures on phase development and mechanical properties in QP980 steel

Bainite microstructures have become increasingly attractive for the development of advanced high-strength steel owing to their balanced strength-plasticity properties.In this study, the final microstructure and mechanical properties of a quenching and partitioning(QP) steel sample after two distinct QP processes were analyzed.The results reveal that martensite transformation after quenching resulted in a lathed morphology with higher yield strength and hole expansion ratio.In contrast, bainite transformation after quenching resulted in the formation of a blocky microstructure composed of bainitic ferrite retained austenite and nanoscale precipitates during the subsequent phase transformation at a higher temperature.This kind of final microstructure is beneficial to the elongation of QP steel but detrimental to the hole expansion ratio.

Prediction and evaluation of optimum quenching temperature and microstructure in a 1300 MPa ultra-high-strength Q&P steel

The quenching and partitioning steel is the representative of the third generation of advanced high-strength steel.The effect of quenching temperature on the microstructure and mechanical property of ferrite-containing quenching and partitioning steel was studied by intercritical annealing quenching and partitioning processes.When preparing a test steel with a tensile strength of 1300 MPa and total elongation of 19%,it is found that the actual optimum quenching temperature was lower than that calculated according to the constrained carbon equilibrium.The results indicate that the martensite start temperature of the austenite was overestimated when considering the diffusion of carbon only.Austenite grain size which is affected by low temperature and the existence of ferrite during intercritical annealing influenced the optimum quenching temperature.A scheme considering the diffusion of various alloying elements and austenite grain size was proposed and verified.Using this scheme,the optimum quenching temperature of intercritically annealed quenching and partitioning steel with complex microstructures was well predicted.

Simulation of temperature field in pipe during single-face quenching process

Temperature-time curves were measured for the air cooling and laminar cooling of a steel plate.Convective heat transfer coefficients of steel plate and air as well as steel plate and laminar cooling water were computed inversely. Therefore,the temperature field in the single-face quenching process of a steel pipe was simulated using ABAQUS finite element softw are,and the relationships betw een the temperatures and quenching time at different positions of the steel pipe were obtained. In addition,the relationships betw een the cooling rates and quenching time,as w ell as betw een cooling rates and temperatures,were obtained. The simulation quickly produced accurate results,and it can be used to optimize the quenching process. In addition,the results provide a basis for rationally designing the composition of a single-face quenching steel pipe.

COUPLED NUMERICAL SIMULATION ON COLD ROLLER'S TEMPERATURE FIFLD-PHASE TRANSFORMATION - STRESS FIELD DURING ITS QUENCHING PSOCESS

Complicated changns occur inside the steel parts during quenching process. The abruptly changed boundary conditions make the temperature field,micro - structure and stress field change dramatically in very short time, and these variables take a contact interactions in the whole process. In this paper, a three dimensional non - linear mathematical model for queeching process has been founded and the numerical simulation on temperature field,microstructre and stress field has been realized.In the FEM analysis, the incremental iteration method is used to deal with such complicated nonlinear as boundary nonlinear, physical property nonlinear,transformation nonlinear etc.The effect of stress on transformation kinetics has been considered in the calculation of microstructure. In the stress field anal- ysis,a thermo- elasto - plastic model has been founded, which considers such factors as transforma- tion strain,transformation plastic strain, themal strain and the effect of temperature and transforma- tion on mechanical propertier etc. The transient temperature field, microstructure distribution and stress field of the roller on any time can be displayed vividly,and the cooling curve and the changes of stress on any position can also be given.

Determination of trace arsenic(V) by catalytic solid substrate-room temperature phosphorescence quenching method

In the H2SO4 medium and in the presence of dodecylbenzene sulfonic acid sodiumsalt (DBS), dimethyl yellow (R) could emit strong and stable solid substrate room temperature phosphorescence (RTP) on filter paper. And NaIO4 could oxidize R to cause the RTP quenching. Arsenic(V) could catalyze the reaction of NaIO4 oxidizing R, which caused the RTP sharply quenching. The reducing value of phosphorescence intensity (ΔIp) for the system with DBS is 3.3 times higher than that without DBS. Moreover, the ΔIp is proportional to the concentration of As(V). Based on the facts above, a new RTP quenching method for the determination of trace As(V) has been established.

Solid Solution Sm_(1+x)Ba_(2-x)Cu_3O_y and Effect of Quench Temperature on SmBa_2Cu_3O_y

By X-ray powder diffraction technique and oxygen content analysis, a solid solution Sm1+xBa2-xCu3Oy has been determined in the range 0≤x≤0.4. When x<0.25. the Sm1+xBa2-xCu3Oy presents orthorhombic symmetry, and the orthorhombic-tetragonaJ transition ocCurs at x = 0.25. With the increase of x, TC decreases and finally breaks. The correlation between ox ygen content and phase structure at different quench temperatures related to Sm Ba2Cu3Oy has been investigated as well

Effect of heat treatment on microstructure and mechanical properties of Ti-containing low alloy martensitic wear-resistant steel

Effects of quenching temperature and cooling conditions(water cooling and 10%NaCl cooling)on microstructure and mechanical properties of a 0.2%Ti low alloy martensitic wear-resistant steel used for die casting ejector plate were investigated.The results show that lath martensite can be obtained after austenitizing in the range of 860-980℃and then water cooling.With an increase in austenitizing temperature,the precipitate content gradually decreases.The precipitates are mainly composed of TiC and Ti4C2S2,and their total content is between 1.15wt.%and 1.64wt.%.The precipitate phase concentration by water-cooling is higher than that by10%NaCl cooling due to the lower cooling rate of water cooling.As the austeniting temperature increases,the hardness and tensile strength of both water cooled and 10%NaCl cooled steels firstly increase and then decrease.The experimental steel exhibits the best comprehensive mechanical properties after being austenitized at 900℃,cooled by 10%NaCl,and then tempered at 200℃.Its hardness,ultimate tensile strength,and wear rate reach551.4 HBW,1,438.2 MPa,and 0.48×10^(-2)mg·m^(-1),respectively.

INFLUENCE OF PROCESSING ON SHAPE MEMORY EFFECT OF Fe-Mn-Si-Ni-C-RE SHAPE MEMORY ALLOY

Effect of carbon, compound RE, quenching temperature, pre-strain and recovery temperature on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloy was studied by bent measurement, thermal cycle training, SEM etc. It was shown that the grains of alloys addition with compound RE became finer and SME increased evidently. SME of the alloy was weakening gradually as carbon content increased under small strain (3%). But in the condition of large strain (more than 6%), SME of the alloy whose carbon content range from 0.1% to 0.12% showed small decreasing range, especially of alloy with the addition of compound RE. Results were also indicated that SME was improved by increasing quenching temperature (>1000℃). The amount of thermal induced martensite increased and the relative shape recovery ratio could be increased to more than 40% after 3-4 times thermal training. The relative shape recovery ratio decreased evidently depending on rising of pre-strain. Furthermore, because speed of martensite transition was extremely great under higher tempering temperature (more than 450℃, ε → γ transition completed in 10s meanwhile the relative shape recovery ratio of the alloy increased rapidly.

Temperature modulation of concentration quenching in lanthanide-doped nanoparticles for enhanced upconversion luminescence

The doping concentration of lanthanide ions is important for manipulating the luminescence properties of upconversion nanoparticles （UCNPs）. However, the serious concentration quenching in highly doped UCNPs remains a vital restriction for further enhanced upconversion luminescence （UCL）. Herein, we examined the effect of temperature on the concentration quenching of rare-earth UCNPs, an issue that has been overlooked, and we show that it is significant for biomedical or optical applications of UCNPs. In this work, we prepared a series of UCNPs by doping Er3. luminescent centers at different concentrations in a NaLuF4：Yb3＋ matrix. At room temperature （298 K）, steady-state photoluminescence （PL） spectroscopy showed substantial concentration quenching of the Er~ emission with increasing doping concentrations. However, the concentration quenching effect was no longer effective at lower temperatures. Kinetic curves obtained from time-resolved PL spectroscopy further showed that the concen- tration quenching dynamics were vitally altered in the cryogenic temperature region, i.e., below 160 K. Our work on the temperature-switchable concentration quenching mechanism may shed light on improving UCL properties, promoting their practical applications.

Tensile behavior and deformation mechanism of quenching and partitioning treated steels at different deforming temperatures

The effects of deforming temperatures on the tensile behaviors of quenching and partitioning treated steels were investigated. It was found that the ultimate tensile strength of the steel decreased with the increasing temperature from 25 to 100 ℃, reached the maximum value at 300 ℃, and then declined by a significant extent when the temperature further reached 400 ℃. The total elongations at 100, 200 and 300 ℃are at about the same level. The steel achieved optimal mechanical properties at 300 ℃due to the proper transformation behavior of retained austenite since the stability of retained austenite is largely dependent on the deforming temperature. When tested at 100 and 200 ℃, the retained aus tenite was reluctant to transform, while at the other temperatures, about 10 vol. % of retained aus- tenite transformed during the tensile tests. The relationship between the stability of retained austenite and the work hardening behavior of quenching and partitioning treated steels at different deforming temperatures was also studied and discussed in detail. In order to obtain excellent mechanical properties, the stability of retained austenite should be carefully controlled so that the effect of transforma tion-induced plasticity could take place continuously during plastic deformation.

Preparation and properties of temperature sensitive paint based on Eu(DBM)_3 phen as probe molecule

Probe molecule Eu(DBM)3 phen is made up of europium oxide(EuO),dibenzoylmethane(DBM) and1,10-phenanthroline(phen). The temperature sensitive paint(TSP) was compounded by the polymerization of the probe molecule, methyl methacrylate(MMA) and the initiator of benzoyl peroxide(BPO).The structure, morphology, luminescence property of probe molecule and the temperature quenching property of the temperature sensitive paint(TSP) were characterized by infrared spectrometer, UV-vis spectrometer, scanning electron microscopy and fluorescence spectrometer respectively. The infrared spectrum and UV-vis spectra show that Eu and DBM form six membered rings, and Eu-O coordinate bonds form. The nanocrystals are in sphere-like morphology with an average size of approximately100 nm. Fluorescence spectra present that the performance of temperature quenching is excellent,what’s more, TSP sample has different temperature sensitivity in various temperature scope. Particularly,under excitation of 286 nm, TSP has a highest temperature sensitivity between 50 and 60 ℃, and the strongest fluorescence emission reaches a peak(615 nm). It indicated that probe molecule(Eu(DBM)phen) has strong luminescent intensity and the temperature quenching properties of Eu(DBM)phen/PMMA is good.

Heat Transfer During Quenching by Plate Roller Quenching Machine

For plate quenching on a roller quenching machine, heat transfer process is investigated. According to the practical online experiment of plate center temperature, average heat transfer coefficient under different conditions and temperature fields are analyzed by numerical simulation. The results show that, at the water temperature of 15 ℃, the instantaneous maximum quenching cooling rate is 17.6 ℃/s for the plate of 50 mm in thickness in roller quenching process. In the temperature range of 400-850 ℃, the maximum is 12.1 ℃/s. With the plate surface temperature decreasing, surface heat transfer coefficient increases at first, and reaches the maximum value of about 15 000 W/（m^2·K）, and then decreases. The calculated heat transfer coefficients are applied to analyze plate temperature field of different thicknesses, and the difference between the calculated and measured temperature is less than 5%.

Microstructure and properties evolution of Nb-bearing medium Cr wear-resistant cast steel during heat treatment

The effect of quenching temperature and cooling conditions on the microstructure and mechanical properties of a 0.2%Nb medium chromium wear-resistant cast steel was investigated.The microstructure,carbides and volume fraction of retained austenite were characterized using the optical microscope,scanning electron microscope,transmission electron microscope and X-ray diffraction.The influence of heat treatment on hardness,impact toughness and tensile properties of test steel was studied.It can be observed that lath martensite can be obtained under the condition of air cooling and oil cooling upon austenitizing in the range of 900–1020℃.Total carbide content of 0.2–1.1 wt.%under air cooling is more than that under oil cooling due to the lower cooling rate.Nb6C5,M23C6 and M7C3 were found at lower austenitizing temperature,of which niobium carbide mostly located at grain boundaries,while chromium carbides were uniformly distributed in the matrix with the size of 20–50 nm.The chromium carbides are basically dissolved into the matrix in test steel austenitized at 1020°C.Meanwhile,the negligible growth of prior austenite grain size is achieved.Specimen austenitized at 1020℃ and cooled in air+tempered at 200℃ has a best combination of hardness,plasticity and tensile strength due to fine grain size and more amount of retained austenite.Under this condition,the hardness is 58 HRC,the impact toughness is 22.92 J/cm^(2),and the tensile strength is 1136.9 MPa.