An approximate analytical model for calculating the pull-in voltage of a stepped cantilever-type radio frequency （RF） micro electro-mechanical system （MEMS） switch is developed based on the Euler-Bernoulli beam an...An approximate analytical model for calculating the pull-in voltage of a stepped cantilever-type radio frequency （RF） micro electro-mechanical system （MEMS） switch is developed based on the Euler-Bernoulli beam and a modified couple stress theory, and is validated by comparison with the finite element results. The sensitivity functions of the pull-in voltage to the designed parameters are derived based on the proposed model. The sensitivity investigation shows that the pull-in voltage sensitivities increase/decrease nonlinearly with the increases in the designed parameters. For the stepped cantilever beam, there exists a nonzero optimal dimensionless length ratio, where the pull-in voltage is insensitive. The optimal value of the dimensionless length ratio only depends on the dimensionless width ratio, and can be obtained by solving a nonlinear equation. The determination of the designed parameters is discussed, and some recommendations are made for the RF MEMS switch optimization.展开更多
The signal transceiver of the software radio fuze depends on the front-end radio frequency（ RF） antenna. RF micro-electro-mechanical-system（ MEMS） smart antennas have the capability of flexible beam rapid scanning...The signal transceiver of the software radio fuze depends on the front-end radio frequency（ RF） antenna. RF micro-electro-mechanical-system（ MEMS） smart antennas have the capability of flexible beam rapid scanning,multi-beam forming and so on,which can improve the ability of detecting,sensing and tracking multiple targets of the fuze. The small RF MEMS smart antenna consists of a 2 × 2 aperture coupled antenna array and six 1-bit MEMS phase shifters. Simulated results demonstrate that the antenna can complete beam steering angles of ± 30° in both X and Y plane at 17. 3 GHz. All components can be fabricated and monolithically integrated with MEMS technology which causes the system low cost and small volume. The RF MEMS smart antenna presents a good and important prospect for the development of the software radio fuze antenna.展开更多
Wireless communication systems which require flexibility and reconfigurability in antenna systems faces main problems like antenna performance, size, weight and cost. A wide band Frequency Reconfigurable Rectangular S...Wireless communication systems which require flexibility and reconfigurability in antenna systems faces main problems like antenna performance, size, weight and cost. A wide band Frequency Reconfigurable Rectangular Slotted Self Similar Antenna has been proposed in this paper. The rectangular slotted patch is repeated for two iterations at different scales and is separated by means of Radio Frequency Micro Electro Mechanical Systems (RF MEMS) switches in order to provide reconfigurability. The antenna can operate in three frequency bandsi.e. K-band, Ku-band and Ka-band by altering the states of RF MEMS switches. To avoid fringing effects and to improve antenna performance, quarter wavelength (λ/4) spacing is required between the antenna and the ground plane. However, a Reconfigurable Antenna requires different λ/4 spacing which is difficult to achieve using a common ground plane. So the Frequency Reconfigurable antenna is integrated with high impedance surface (HIS) like Electronic Band Gap (EBG) structures to suppress standing waves and surface waves with a unified profile thickness of 1.75 mm. The overall dimension of the proposed antenna along with RF MEMS Switch, feed element and HIS is about 8 mm × 8 mm × 1.75 mm. The simulated results of the proposed antenna reveal enhancement in antennas performance like Voltage Standing Wave Ratio (VSWR), Front to Back Ratio (FBR) and bandwidth when it is placed over HIS EBG. Also the radiation patterns of the proposed antenna when placed over EBG shows the suppression of side lobe and backward radiation.展开更多
基金supported by the National Natural Science Foundation of China(Nos.51505089 and61204116)the Opening Project of the Science and Technology on Reliability Physics and Application Technology of Electronic Component Laboratory(Nos.ZHD201207 and 9140C030605140C03015)the Pearl River S&T Nova Program of Guangzhou(No.2014J2200086)
文摘An approximate analytical model for calculating the pull-in voltage of a stepped cantilever-type radio frequency （RF） micro electro-mechanical system （MEMS） switch is developed based on the Euler-Bernoulli beam and a modified couple stress theory, and is validated by comparison with the finite element results. The sensitivity functions of the pull-in voltage to the designed parameters are derived based on the proposed model. The sensitivity investigation shows that the pull-in voltage sensitivities increase/decrease nonlinearly with the increases in the designed parameters. For the stepped cantilever beam, there exists a nonzero optimal dimensionless length ratio, where the pull-in voltage is insensitive. The optimal value of the dimensionless length ratio only depends on the dimensionless width ratio, and can be obtained by solving a nonlinear equation. The determination of the designed parameters is discussed, and some recommendations are made for the RF MEMS switch optimization.
文摘The signal transceiver of the software radio fuze depends on the front-end radio frequency（ RF） antenna. RF micro-electro-mechanical-system（ MEMS） smart antennas have the capability of flexible beam rapid scanning,multi-beam forming and so on,which can improve the ability of detecting,sensing and tracking multiple targets of the fuze. The small RF MEMS smart antenna consists of a 2 × 2 aperture coupled antenna array and six 1-bit MEMS phase shifters. Simulated results demonstrate that the antenna can complete beam steering angles of ± 30° in both X and Y plane at 17. 3 GHz. All components can be fabricated and monolithically integrated with MEMS technology which causes the system low cost and small volume. The RF MEMS smart antenna presents a good and important prospect for the development of the software radio fuze antenna.
文摘Wireless communication systems which require flexibility and reconfigurability in antenna systems faces main problems like antenna performance, size, weight and cost. A wide band Frequency Reconfigurable Rectangular Slotted Self Similar Antenna has been proposed in this paper. The rectangular slotted patch is repeated for two iterations at different scales and is separated by means of Radio Frequency Micro Electro Mechanical Systems (RF MEMS) switches in order to provide reconfigurability. The antenna can operate in three frequency bandsi.e. K-band, Ku-band and Ka-band by altering the states of RF MEMS switches. To avoid fringing effects and to improve antenna performance, quarter wavelength (λ/4) spacing is required between the antenna and the ground plane. However, a Reconfigurable Antenna requires different λ/4 spacing which is difficult to achieve using a common ground plane. So the Frequency Reconfigurable antenna is integrated with high impedance surface (HIS) like Electronic Band Gap (EBG) structures to suppress standing waves and surface waves with a unified profile thickness of 1.75 mm. The overall dimension of the proposed antenna along with RF MEMS Switch, feed element and HIS is about 8 mm × 8 mm × 1.75 mm. The simulated results of the proposed antenna reveal enhancement in antennas performance like Voltage Standing Wave Ratio (VSWR), Front to Back Ratio (FBR) and bandwidth when it is placed over HIS EBG. Also the radiation patterns of the proposed antenna when placed over EBG shows the suppression of side lobe and backward radiation.
