Method for rapid warning and activity concentration estimates in online waterγ-spectrometry systems

Onlineγ-spectrometry systems for inland waters,most of which extract samples in situ and in real time,are able to produce reliable activity concentration measurements for waterborne radionuclides only when they are distributed relatively uniformly and enter into a steady-state diffusion regime in the measurement chamber.To protect residents’health and ensure the safety of the living environment,better timeliness is required for this measurement method.To address this issue,this study established a mathematical model of the online waterγ-spectrometry system so that rapid warning and activity estimates can be obtained for water under non-steady-state(NSS)conditions.In addition,the detection efficiency of the detector for radionuclides during the NSS diffusion process was determined by applying the computational fluid dynamics technique in conjunction with Monte Carlo simulations.On this basis,a method was developed that allowed the online waterγ-spectrometry system to provide rapid warning and activity concentration estimates for radionuclides in water.Subsequent analysis of the NSS-mode measurements of^(40)K radioactive solutions with different activity concentrations determined the optimum warning threshold and measurement time for producing accurate activity concentration estimates for radionuclides.The experimental results show that the proposed NSS measurement method is able to give warning and yield accurate activity concentration estimates for radionuclides 55.42 and 69.42 min after the entry of a 10 Bq/L^(40)K radioactive solution into the measurement chamber,respectively.These times are much shorter than the 90 min required by the conventional measurement method.Furthermore,the NSS measurement method allows the measurement system to give rapid(within approximately 15 min)warning when the activity concentrations of some radionuclides reach their respective limits stipulated in the Guidelines for Drinking-water Quality of the WHO,suggesting that this method considerably enhances the warning capacity of in situ online waterγ-spectrometry systems.

Rapid Detection of Somatic Cell Count Based on Hybrid Variable Selection Method

Somatic cell count detection is the daily work of dairy farms to monitor the health of cows.The feasibility of applying near-infrared spectroscopy to somatic cell count detection was researched in this paper.Milk samples with different somatic cell counts were collected and preprocessing methods were studied.Variable selection algorithm based on hybrid strategy and modelling method based on ensemble learning were explored for somatic cell count detection.Detection model was used to diagnose subclinical mastitis and the results showed that near-infrared spectroscopy could be a tool to realize rapid detection of somatic cell count in milk.

Study of the reaction mechanism for preparing powdered activated coke with SO_(2)adsorption capability via one-step rapid activation method under flue gas atmosphere

In this study,the impact of different reaction times on the preparation of powdered activated carbon(PAC)using a one-step rapid activation method under flue gas atmosphere is investigated,and the underlying reaction mechanism is summarized.Results indicate that the reaction process of this method can be divided into three stages:stage I is the rapid release of volatiles and the rapid consumption of O_(2),primarily occurring within a reaction time range of 0-0.5 s;stage II is mainly the continuous release and diffusion of volatiles,which is the carbonization and activation coupling reaction stage,and the carbonization process is the main in this stage.This stage mainly occurs at the reaction time range of 0.5 -2.0 s when SL-coal is used as material,and that is 0.5-3.0 s when JJ-coal is used as material;stage III is mainly the activation stage,during which activated components diffuse to both the surface and interior of particles.This stage mainly involves the reaction stage of CO_(2)and H2O(g)activation,and it mainly occurs at the reaction time range of 2.0-4.0 s when SL-coal is used as material,and that is 3.0-4.0 s when JJ-coal is used as material.Besides,the main function of the first two stages is to provide more diffusion channels and contact surfaces/activation sites for the diffusion and activation of the activated components in the third stage.Mastering the reaction mechanism would serve as a crucial reference and foundation for designing the structure,size of the reactor,and optimal positioning of the activator nozzle in PAC preparation.

Establishment of High-sensitivity Rapid Fluorescence Quantitative Detection Method for Antibody against Peste des Petits Ruminants Virus

[Objectives]This study was conducted to establish a rapid quantitative method for detecting antibody against Peste des Petits Ruminants Virus(PPR V)in sheep serum.[Methods]Soluble N protein and NH fusion protein were obtained in Escherichia coli prokaryotic expression system by optimizing codons and expression conditions of E.coli.Furthermore,based on the purified soluble N protein and NH fusion protein,a high-sensitivity fluorescence immunoassay kit for detecting the antibody against PPR V was established.[Results]The method could quickly and quantitatively detect PPR V antibody in sheep serum,with high sensitivity and specificity,without any cross reaction to other related sheep pathogens.The intra-batch and inter-batch coefficients of variation were less than 10%and 15%,respectively,and the method had good repeatability.Through detection on 292 clinical serum samples,it was compared with the French IDVET competitive ELISA kit,and the coincidence rate of the two methods reached 93.84%.Compared with the serum neutralization test,the detected titer value of the high-sensitivity rapid fluorescence quantitative detection method was basically consistent with the tilter value obtained by the neutralization test on the standard positive serum(provided by the WOAH Brucellosis Reference Laboratory of France).[Conclusions]This method can realize rapid quantitative detection of PPR V antibody on site,and has high practical value and popularization value.

A Rapid DNA Extraction Method for PCR Detection of Arabidopsis thaliana

[Objective] The aim was to introduce a rapid DNA extraction method for PCR detection of Arabidopsis thaliana.[Method] Through the improvement of conventional DNA extraction method,a rapid Arabidopsis thaliana DNA extraction method was obtained.With randomly selected Arabidopsis thaliana transgenic strains and mutants as samples,the method was verified.[Result] After electrophoresis,UV absorption detection,it was found that DNA samples are complete and less pollution,and the result of PCR amplification objective fragment was good which proved DNA is suitable as a template for PCR reaction.After PCR detection,positive plants gene amplified bands were clear,without false-positive,and the test results were satisfactory.[Conclusion] The method is suitable for rapid extraction of Arabidopsis thaliana DNA and PCR detection.

A New Rapid and Batch-oriented Crushing Method for DNA Extraction from Maize Leaves

The crushing of leaves is the most time and effort-consuming part in DNA extraction which is a fundamental step in the study of molecular biology. In this study, a new rapid and batch-oriented crushing method for DNA extraction from maize leaves was developed. In addition, the practicability of the developed method in molecular marker-assisted breeding was verified using SSR molecular maker technology so as to provide a rapid, batch-oriented, low-cost and non-toxic leafcrushing method for a large number of molecular marker tests, improving test efficiency.

A Rapid and Simple Method for the Detection of Rice Dwarf Virus by Aqueous Extract

Rice dwarf disease caused by rice dwarf virus （RDV） is one of the major rice virus diseases in China,which widely distributes in the rice area of China.A simple and rapid method for detection of RDV in rice plants and Nephotettix cincticeps was investigated in this study,and the whole detection only lasted for 20 min.After diseased leaves of rice （10 mg） and leaves of Nephotettix cincticeps （10 mg） both infected by RDV were ground by sterile water （100 μl）,the supernatant was analyzed by 1% agarose gel electrophoresis to steadily detect five specific electrophoretic bands with 1 000 bp to 5 000 bp.However,there was no electrophoretic band in the healthy rice leaves and aqueous extract of non-viruliferous N.cincticeps.Therefore,this method was more rapid and simple to detect RDV in rice plants and Nephotettix cincticeps,which avoided expensive reagents and tedious steps of conventional serological testing and molecular detection （RT-PCR and Western-blot）.

A Rapid Method for the Isolation of Small Amount DNA from Citrus Early Embryo

[Objective] The present study aimed to establish a rapid method for the isolation of small amount DNA from citrus.[Method] By using the improved CTBA method,the genomic DNA was extracted respectively from 20,10,5 and 2.5 mg hybrid embryos of citrus,and then the DNA quality was detected and followed by SSR verification.[Result] The method was very simple and rapid,which needed less materials.In addition,the isolated DNA showed good purity with the OD260/OD280 of 1.8-2.1,and could meet the requirement for PCR-based technology,such as SSR,etc..[Conclusion] The method could be used for rapid extraction of small amount of genomic DNA from citrus.

A Mass and Rapid Method for DNA Extraction of Beauveria bassiana

[Objective] The aim was to optimize the mass and rapid method for DNA extraction of Beauvena bassiana. [Method] Boiling water DNA extraction method was improved, DNA extraction liquid was heated by PCR instrument and the extraction process was finished rapidly. [ Resuit] The quality of DNA obtained through mass and rapid extraction of fungal genomic DNA could meet the requirement of RAPD amplification analysis. The clear bands were amplified from 22 tested strains, the number of clear bands were different in the range of 2 -6 and the size of band were mainly concentrated in 450 -800 bp. The DNA extracted by this method also could completely meet the requirement of SCAR amplification. The amplified specific DNA bands used to mark the strain F263 were very clear. [Conclusion] This research provided relatively perfect method for mass and rapid extraction of fungal clenomic DNA.

Study on the Rapid Method to Predict Longevity of Controlled Release Fertilizer Coated by Water Soluble Resin

The study discussed the rapid method to test and predict the longevity of controlled release fertilizers （CRFs） coated by water soluble resin by using the short-term leaching under higher temperature. Pure water dissolving incubation and higher temperature leaching were used to study the patterns of the nutrient release of the CRFs. The correlation analysis between the days at 25℃ and the hours at 80℃ of Trincote 1 and Trincote 2 for the same cumulative release rates were conducted. Patterns of cumulative nutrient release curve followed one factor quadratic regression equation at each given temperatures, and each of relative coefficient was bigger than 0.995. As the temperature increased, nutrients release of the CRFs increased. The longevity of resin coated CRFs were predicted by use of both the cumulative nutrients release equation at 80℃ and the regression equation of release time needed for the same cumulative release rates between 25 and 80℃. There were only 0.3-6.9% relative errors between the tested longevity and predicted one. In conclusion, the longevity of resin coated CRFs could be predicted more quickly and precisely by use of the higher temperature short-term leaching method than that of the traditional differential release rate. The longevity of resin coated CRF could be rapidly and precisely predicted in a few hours by application of the higher temperature shortterm leaching method.

Rapid diagnostic method for transplutonium isotope production in high flux reactors

Transplutonium isotopes are scarce and need to be produced by irradiation in high flux reactors.However,their production is inefficient,and optimization studies are necessary.This study analyzes the physical nature of transplutonium isotope produc-tion using ^(252)Cf,^(244)Cm,^(242)Cm,and ^(238)Pu as examples.Traditional methods based on the Monte Carlo burnup calculation have the limitations of many calculations and cannot analyze the individual energy intervals in detail;thus,they cannot sup-port the refined evaluation,screening,and optimization of the irradiation schemes.After understanding the physical nature and simplifying the complexity of the production process,we propose a rapid diagnostic method for evaluating radiation schemes based on the concepts“single energy interval value(SEIV)”and“energy spectrum total value(ESTV)”.The rapid diagnostic method not only avoids tedious burnup calculations,but also provides a direction for optimization.The optimal irradiation schemes for producing ^(252)Cf,^(244)Cm,^(242)Cm,and ^(238)Pu are determined based on a rapid diagnostic method.Optimal irradiation schemes can significantly improve production efficiency.Compared with the initial scheme,the optimal scheme improved the production efficiency of ^(238)Pu by 7.41 times;^(242)Cm,11.98 times;^(244)Cm,65.20 times;and ^(252)Cf,15.08 times.Thus,a refined analysis of transplutonium isotope production is conducted and provides a theoretical basis for improving production efficiency.

Study on a noninvasive method for rapid screening Human Serum albumin injectables by Raman spectroscopy

Human serum albumin(HSA)injectable product is a severely afflicted area on drug safety due to its high price and restricted supply.Raman spectroscopy performances high specificity on HSA detection and it is even possible to determine HSA injectable products noninvasively.In this study,we developed a noninvasive rapid screening method for of HSA injectable products by using portable Raman spectrometer.Qualitative models were established by using principal component analysis combined with classical least squares(PCA-CLS)algorithm,while quanti-tative model was established by using partial least squares(PLS)algorithm.Model transfer in different instruments of both the same and different apparatus modules was further discussed in this paper.A total of 34 HSA injectable samples collected from markets were used for verification.The identification results showed 100%accuracy and the predicted concentrations of those identified as true HSA were consistent with their labeled concentrations.The quantitative results also indicated that model transfer was excellent in the same apparatus modules of Raman spectrometer at all concentration levels,and still good enough in the different apparatus modules although the relative standard deviation(RSD)value showed a little increasing trend at low HSA concentration level.In conclusion,the method was proved to be feasible and efficient for screening HSA injections,especially on its screening speed and the consideration of glass containers.Moreover,with inspiring results on the model transfer,the method could be used as a universal screening mean to different Raman instruments.

Enzyme Inhibition Rate Method for Rapid Detection of Organophosphorus and Carbamate Pesticides in Cowpea

[Objectives ] The paper was to explore enzyme inhibition rate method for rapid detection of organophosphorus and carbamate pesticides in cowpea. [ Methods ] Acetylcholinesterase （ACHE） was added to cowpea extract, to determine the inhibition rate of extract against enzyme. The influences of different sampiing methods and sampling parts on detection results were compared. [ Results] The positive rate of standard sampling was 18.18% higher than that of non-stand- ard sampling, and the positive rate of samples collected from cowpea tail was 16.67% higher than that collected from other parts. [ Condmions] Enzyme inhibi- tion rate method is suitable for rapid detection of organophosphorus and carbamate pesticides in cowpea.

Tire Dynamics Modeling Method Based on Rapid Test Method

Combined with the tire dynamics theoretical model,a rapid test method to obtain tire lateral and longitudinal both steady-state and transient characteristics only based on the tire quasi-steady-state test results is proposed.For steady state data extraction,the test time of the rapid test method is half that of the conventional test method.For transient tire characteristics the rapid test method omits the traditional tire test totally.At the mean time the accuracy of the two method is much closed.The rapid test method is explained theoretically and the test process is designed.The key parameters of tire are extracted and the comparison is made between rapid test and traditional test method.The result show that the identification accuracy based on the rapid test method is almost equal to the accuracy of the conventional one.Then,the heat generated during the rapid test method and that generated during the conventional test are calculated separately.The comparison shows that the heat generated during the rapid test is much smaller than the heat generated during the conventional test process.This benefits to the reduction of tire wear and the consistency of test results.Finally,it can be concluded that the fast test method can efficiently,accurately and energy-efficiently measure the steady-state and transient characteristics of the tire.

Rapid testing methods for food contaminants and toxicants

Food safety is one of the major concerns in every country regardless of the economic and social development. The frequent occurrence of food scandals in the world has led the Chinese government to implement several strategies to fortify the food supply system to a high food safety standard. This relies heavily on laboratory testing services but conventional methods for detection of food contaminants and toxicants are limited by sophisticated sample preparation procedures, long analysis time, large instruments and professional personnel to meet the increasing demands. In this review, we have incorporated most of the current and potential rapid detection methods for many notorious food contaminants and toxicants including microbial agents, toxic ions, pesticides, veterinary drugs and preservatives, as well as detection of genetically modified food genes and adulterated edible oil. Development of rapid, accurate, easy-to-use and affordable testing methods could urge food handlers and the public to actively screen for food contaminants and toxicants instead of passively relying on monitoring by the government examination facility. This review also provides several recommendations including how to encourage the public to engage in the food safety management system and provide optimal education and financial assistance that may improve the current Chinese food safety control system.

A Rapid Method for Measuring Seed Protein Content in Cowpea (<i>Vigna unguiculata</i>(L.) Walp)

Cowpea (Vigna unguiculata (L.) Walp), a legume crop that is grown in the worldwide, provides beneficial proteins for human consumption and animal feeding. In comparison, Rapid N analyzer as traditional method, has been widely used to measure protein content through the percentage of total nitrogen in the seed’s grounded powder. Near-Infrared Reflectance (NIR) has commonly been used to measure protein content in soybean seeds using whole grain without the need of seed grinding, which makes it possible to obtain fast results at a lower cost-per-analysis than the traditional combustion method. The specific objective of this study is to test a rapid method for measuring cowpea seed protein content by the NIR analyzer comparing to the traditional rapid N analyzer. A total of 240 cowpea genotypes were used in this study, including six seed coat colors, black, blackeye, browneye, cream, pinkeye, and red with 40 cowpea genotypes. The results showed that a linear relationship exists between the NIR analyzer and the Rapid N analyzer in the six different color groups. The correlation efficiency (r) between the seed protein contents from NIR and Rapid N was higher for pinkeye seed (r = 0.867), blackeye (0.771), cream (0.729), browneye (0.700), and red (0.623), respectively, but lower for black seeds, indicating that the NIR analyzer can be used to measure protein content for cowpea seeds with the five types of seed coat except black. Overview, the cowpea seed protein content measured from the NIR analyzer showed a little higher seed protein content. A series of regression models with different seed coat color have been built to adjust to protein content of colorful cowpea seeds from the NIR analyzer. But, it is not recommended to use for black color seeds due to a very low correlation efficiency (r) value with 0.184.

Rapid Springback Compensation for Age Forming Based on Quasi Newton Method

Iterative methods based on finite element simulation are effective approaches to design mold shape to compensate springback in sheet metal forming. However, convergence rate of iterative methods is difficult to improve greatly. To increase the springback compensate speed of designing age forming mold, process of calculating springback for a certain mold with finite element method is analyzed. Springback compensation is abstracted as finding a solution for a set of nonlinear functions and a springback compensation algorithm is presented on the basis of quasi Newton method. The accuracy of algorithm is verified by developing an ABAQUS secondary development program with MATLAB. Three rectangular integrated panels of dimensions 710 mmx750 mm integrated panels with intersected ribs of 10 mm are selected to perform case studies. The algorithm is used to compute mold contours for the panels with cylinder, sphere and saddle contours respectively and it takes 57%, 22% and 33% iterations as compared to that of displacement adjustment （DA） method. At the end of iterations, maximum deviations on the three panels are 0.618 4 mm, 0.624 1 mm and 0.342 0 mm that are smaller than the deviations determined by DA method （0.740 8 mm, 0.740 8 mm and 0.713 7 mm respectively）. In following experimental verification, mold contour for another integrated panel with 400 ram^380 mm size is designed by the algorithm. Then the panel is age formed in an autoclave and measured by a three dimensional digital measurement devise. Deviation between measuring results and the panel＇s design contour is less than 1 mm. Finally, the iterations with different mesh sizes （40 mm, 35 mm, 30 mm, 25 mm, 20 mm） in finite element models are compared and found no considerable difference. Another possible compensation method, Broyden-Fletcher-Shanmo method, is also presented based on the solving nonlinear fimctions idea. The Broyden-Fletcher-Shanmo method is employed to compute mold contour for the second panel. It only takes 50% iterations compared to that of DA. The proposed method can serve a faster mold contour compensation method for sheet metal forming.

Rapid onset hazards,fault-controlled landslides and multi-method emergency decision-making

Numerous large-scale fragmented bedrock landslides developed along major fault system is a world-wide phenomenon,which are often characterized with repeated reactivation throughout histories.Due to the large-scale and deep-seated features,it is normally difficult to control such landslides,which in turn pose great threat to local residents and infrastructures.Therefore,monitoring and forecasting these gigantic landslides has become a key protocol for risk reduction.This paper introduces such a typical massive landslide,named Yahuokou landslide,besides Min River in Zhouqu County,Gansu Province,China.Reactivated on July 16,2019 with a volume of approximately 4×106 m3,moving slowly and transitionally starting from top part,its toe had partially blocked the Min River and destroyed roads and houses eventually by August 11,2019.As to emergency response for such huge slowmoving landslide,there is no standard national protocols.Therefore,how to make effective emergency decision has become a challenge.Based on previous experiences,integrated multi-methods,including UAV imagery interpretation,we applied GNSS monitoring and field investigations in the early stages of landsliding,in order to assist the decisionmaking.The results show that the movement path of the current displacement is consistent with that of the 1989 reactivation event,and the slide body was separated into three relatively independent blocks with different sliding velocities and responses to rainfall.The upper and lower blocks appeared less affected by rainfall,while the middle block responded more to the changes in precipitations.It proves that the combined approaches using a variety of monitoring techniques can play an effective role in the monitoring of rapidly deformed transitional largescale landslides,and can also provide a set of reference methods for the emergency disposal of similar landslide hazards.

Rapid communication Preparation of TiO_2 nanometer thin films with high photocatalytic activity by reverse micellar method

Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic force microscopy (AFM), BET surface area and X-rayphotoelectron spectroscopy (XPS). Photocatalytic activity was evaluated by photocatalyticdecoloration of methyl orange aqueous solution. The results showed that the TiO_2 thin filmsprepared by reverse micellar method (designated as RM-TiO_2 films) showed higher photocatalyticactivity than those by sol-gel method (designated as SG-TiO_2 films). This is attributed to the factthat the former is composed of smaller monodispersed spherical particles with a size of about 15 nmand possesses higher surface areas.

Development of a rapid GC-FID method to simultaneously determine triethylamine, diisopropylamine, and 1,1,3,3-tetramethylguanidine residues in an active pharmaceutical ingredient

A rapid GC-FID method was developed to simultaneously determine residual levels of triethylamine(TEA), 1,1,3,3-tetramethylguanidine(TMG), and diisopropylamine(DIPA) in the synthetic route of an active pharmaceutical ingredient(API). Due to the severe absorption of amines on GC stationary phases,GC columns with various stationary phases were evaluated for optimal peak shape and reproducibility.The final conditions used the Agilent CP-Volamine column to resolve the three amines in 12 min. Various inlet liners were also screened to further improve the sensitivity of the analysis. The Restek Siltek~? liner was selected to achieve the desired detectability for the method. The quantitation limits were 4, 3, and 4 mg/mL for TEA, DIPA, and TMG in the presence of API, respectively. All three amines showed good linearity(r > 0.999) and recoveries(> 90%) over the concentration range of 3 to 16 mg/mL. The testing of residual amines was initially performed at the penultimate stage of the synthesis. However, this work demonstrates that TMG can act as a proton sponge to react with salicylic acid, the counter ion of the penultimate, to form a volatile component that elutes at a different retention time. Consequently, in the final method, these three amines were monitored in the final API to circumvent the matrix interference.Key parameters of the method were qualified per method validation requirements in ICH guidelines. The method was successfully applied for batch testing during development and implemented as an inprocess control procedure at manufacturing sites.