Mechanism of interaction relation between the rare-earth element Ce and impurity elements Pb and Bi in Ag-based filler metal

The mechanism of interaction relation between the rare-earth element Ce and elements Pb and Bi in Ag-based filler metal has been studied. The results show that the compounds CePb and CeBi with high melting point can be easily produced between these three elements in the filler metal, which greatly limited the formation of the isolated phase Pb or Bi and also eliminated the bad effect of impurity elements Pb and Bi on the spreading property of Ag-based filler metal. The metallurgical and quantum-mechanical bond formation analysis show that a strong chemical affinity was existed between the rare-earth element Ce and impurity elements Pb and Bi, which was proved by the XRD analysis results.

Modification Behavior of Trace Rare Earth on Impurity Phases in Commercial Purity Aluminum

Modifying effect and mechanism of trace rare earth on Fe(Si) rich impurity phases in commercial purity aluminum were studied with the aids of SEM, EDAX, TEM, etc. It is found that Ce rich mixed rare earth (RE) is an effective modifying agent, which makes the coarse Fe rich impurity phases transform into complex compounds of tiny, sphere/short stick form, thus improving mechanical properties of this material; its modifying mechanism is in that RE gathering in front of solid/liquid interface enters into the impurity phases, forming complex (AlFeSiRE) compounds; or is adsorbed in the impurity phases surface, impeding the growth of impurity phases; however, excessive RE will result in the increasing of RE compounds (secondary phases), and plasticity reduction of this material. Therefore, its addition amount should be less than 0 07% (mass fraction).

Anomalous Concentrations of Rare Metal Elements, Rare-scattered(Dispersed) Elements and Rare Earth Elements in the Coal from Iqe Coalfield, Qinghai Province, China

Total of 23 bench samples were taken from the No. 7 Coal of Iqe Coalfield, Qinghai Province, China, following Chinese Standard Method GB/T 482-2008 （2008）. These samples were analyzed by powder X-ray diffraction （XRD）, inductively coupled plasma mass spectrometry （ICP- MS） and X-ray fluorescence （XRF）. The results indicate that the No. 7 Coal belongs to a low rank （Ro.ran =0.659%） and high-ash coal （40.54%）. Compared to common Chinese and world low-rank coals, the lqe coal contains anomalous concentrations of rare metal elements, rare-scattered （dispersed） elements and rare earth elements. The highest contents of Rb, Cs, Ga and REY reach to 180, 26, 37, and 397 ppm, respectively. Their average contents of these elements are 10.9, 15, 4.8 and 3.5 times higher than those of world coals, respectively. Minerals in the coal include kaolinite, quartz, muscovite, siderite, and traces of rutile, and brookite. Kaolinite could be main host minerals of Rb, Cs, Ga and REY. The anomalous rare element Rb and Cs accumulation in the Iqe coal is related to both organic and inorganic matter. The REY concentrations may be related to circulation of thermal solutions, contained or sorbed by clayey particles, and organic matter as well.

Thermodynamics of Modifying Effect of Rare Earth Oxide on Inclusions in Hardfacing Metal of Medium-High Carbon Steel

The modifying effect of rare earth (RE) oxide on inclusions in hardfacing metals of medium-high carbon steel was investigated by means of thermodynamics. The thermodynamic analysis for inclusion formation shows that RE oxide can be reduced to RE element by carbon, then the RE element can react with oxygen and sulfur to form the RE oxide, RE sulfide and RE oxide-sulfide in hardfacing molten pool. The deoxidization and the desulphurization can be carried out and the liquid metal can be purified. In addition, RE oxide can also react with sulfur to form RE oxide-sulfide directly. Therefore, the harmful effect of sulfur can be decreased.

Effect of Rare Earth on Microstructure of γ-TiAl Intermetallics

The rare earth (RE) elements (Ce, La) were added to binary Ti 47% Al alloys (atomic fraction) by Induction Skull Melting. The element Ce of 1.0 atomic percent was added individually, and La of 0.2 atomic percent was added individually. This article studied the influences of rare earth metal (Ce, La) on microstructure of as cast TiAl based alloy by XRD, SEM, EMPA and TEM measurement methodology. The results show that most of rare earth rich phases (AlCe, AlLa) are uniformly distributed in grain boundary in the shape of discontinuous network, and some particles of rare earth rich phases within the grains are mainly ellipsoids. In addition, rare earth element can obviously refine the grain size and the lamellar thickness of as cast TiAl based alloy samples. The grain size of Ti 47Al 1.0Ce 0.2La alloy reaches about 30～80 μm, and the lamellar thickness of its γ phase and α 2 phase are less than 200 and 20 nm, respectively.

Microstructure evolution of rare earth Pr modified alumina-silicate short fiber-reinforced Al-Si metal matrix composites

Al-Si metal matrix composites (MMCs) reinforced with 20 vol.% alumina-silicate shot fibers (Al2O3-SiO2(sf)) were fabricated by an infiltration squeeze method. Pure Pr metal was added into these composites. The effect of Pr addition on the microstructure evolution of Al-Si MMCs was investigated by SEM,TEM,and EDS. Pr addition is favorable to make uniform microstructures with the modified eutectic Si crystal. PrAlSi phase with high contents of Pr and Si is observed on the interface between the fiber and the matrix. The addition of Pr promotes interface SiO2 reduction,and SiO2 comes from the crystallization of Al2O3-SiO2 short fibers.

Hydrogen production from coke oven gas over LiNi/γ-Al_2O_3 catalyst modified by rare earth metal oxide in a membrane reactor

The performance of LiNi/γ-Al2O3 catalysts modified by rare earth metal oxide （La2O3 or CeO2） packed on BCFNO membrane reactor was discussed for the partial oxidation of methane （POM） in coke oven gas （COG） at 875 ℃. The NiO/γ-Al2O3 catalysts with different amounts of La2O3 and CeO2 were prepared with the same preparation method and under the same condition in order to compare the reaction performance （oxygen permeation, CH4 conversion, H2 and CO selectivity） on the membrane reactor. The results show that the oxygen permeation flux increased significantly with LiNiREOx/γ-Al2O3 （RE = La or Ce） catalysts by adding the element of rare earth especially the Ce during the POM in COG. Such as, the Li15wt%CeO29wt%NiO/γ-Al2O3 catalyst with an oxygen permeation flux of 24.71 ml·cm^-2·min^-1 and a high CH4 conversion was obtained in 875 ℃. The resulted high oxygen permeation flux may be due to the added Ce that inhibited the strong interaction between Ni and Al2O3 to form the NiAl2O4 phase. In addition, the introduction of Ce leads up to an important property of storing and releasing oxygen.

Characteristics of highly differentiated granite and metallization of tungsten-tin, rare and rare earth metal in the eastern Nanling region, China

1 Introduction Massive tungsten-tin,rare and rare earth metals ore deposits were formed with the widespread granite magmatic activity in early Yanshanian period in the eastern Nanling region.Recent studies indicate that the Yanshanian highly differentiated-granite formation is closely related to the deposits of tungsten and tin,rare and rare earth metals mineralization in the region(Xiao

Some Rare Earth Metallic Organohydrides with Biindenyl as the Ligand

Introduction It is well known that organometallic hydrides of rare earth metals are the catalysts and reducing reagents for the catalysis polymerization of alkenes and the catalysis hydrogenation of alkenoalkynes. There are four methods for the syntheses of organometallic hydrides of rare earth metals:（1） the thermal atomization of metals, i.e., the interaction of a rare earth metal with alkenes with a terminal alkyne;（2） the Ln—Cσ bond is broken with H;;（3） metal-

Effect of mixed rare earth and Sr on microstructure and brazability of Al-20Cu-5Si-2Ni filler metal

The objective of this study is to investigate the influence of adding tiny amount of mixed rare earth （ La, Ce） and Sr to Al-20Cu-SSi-2Ni filler metal, by analyzing the microstructure, wettability and mechanical properties of brazed joints. The results show that with the addition of mixed rare earth （La, Ce ） into Al-2OCu-SSi-2Ni alloy, the α-Al solid solution as well as CuAl2 （ Ni） intermetallic compound phase significantly reduced, while more Al-Si eutectic phase and AI-Si-Cu ternary eutectic phase were produced. And as mixed rare earth （La, Ce ） added in, the wettability of Al-2OCu-SSi-2Ni filler metal decreased, while the shear strength of the brazed joints increased. The addition of Minor Sr modificated Al-2OCu-SSi-2Ni filler metal, further reduced the CuAl2 （ Ni ） intermetallic compound phase, which was partially replaced Al-Si-Cu ternary eutectic phase. As a result, the tensile strength as well as the wettability of the filler metal was improved.

Modifying Behaviors of Ultrasonic Irradiation and Rare Earth Metal Cerium on Electroless Co-Ni-B Alloy Coating

By plasma transmitting spectrograph,electron energy spectrometry,X-ray diffractometry,transmission electron microscopy and micro-hardometry,the effects of ultrasonic irradiation and rare earth metal cerium on the depositing speed,chemical composition,crystal structure and microhardness of electroless Co-Ni-B alloy coating were inspected and analyzed. The results show that cerium and ultrasonic irradiation can evidently raise the depositing speed of electroless Co-Ni-B alloy. The cerium content of electroless Co-Ni-B-Ce alloy coating also increases after ultrasonic irradiation applied to electroless Co-Ni-B plating process. Under the action of ultrasonic irradiation and rare metal cerium,the chemical composition of electroless Co-Ni-B alloy coating is changed. Electroless Co-Ni-B alloy with amorphous structure is transformed to electroless Co-Ni-B-Ce alloy with microcrystalline in general state and electroless Co-Ni-B-Ce alloy with crystalline structure in ultrasonic irradiation. In this way microhardness of the coatings increases remarkably.

Impact Wear Properties of Metal-Plastic Multilayer Composites Filled with Glass Fiber Treated with Rare Earth Element Surface Modifier

The friction and wear properties of metal-plastic multilayer composites filled with glass fiber, which is treated with rare earth element surface modifier, under impact load and dry friction conditions were investigated. Experimental results show that the metal-plastic multilayer composite filled with glass fiber exhibits excellent friction and impact wear properties when using rare earth elements as surface modifier for the surface treatment of glass fiber.

New cadmium and rare earth metal tungstates with the scheelite type structure

New cadmium and rare earth metal tungstates with the formula Cd0.25RE0.50 0.25WO4 （RE=Nd, Sin, Eu, Gd, D-statistical distrib- uted vacancies in cation sublattice） were synthesized by the solid-state reaction between CdWO4 and corresponding RE2W209. The obtained phases crystallize in the scheelite type structure. The Cd0.25RE0.5 0.25WO4 compounds were characterized by X-ray diffractometer （XRD）, （DTA-TG）, infrared （IR） and EPR methods.

Synthesis and Structures of A Series of Novel Rare Earth Transition Metal Sulfates

Seven new rare earth transition metal sulfates were synthesized by hydrothermal reactions under conditions slightly above the critical point of water. Their crystal structures were determined from single crystal X-ray data. The compositions of the new compounds can be represented by two general formulae ： REM （OH） 3 （SO4） and RE2M （OH） 3 （SO4） 2F （H2O） with RE = Gd, Tb, Dy ; M = Ni, Cu. Three different crystal structure types were found for the formula REM （OH） 3 （SO4）. The structures of the new compounds all feature infinite chains of REOn coordination polyhedra, which are connected to chains of CuO6 or NiO6 octabedra. The limited size range of the rare earth cations observed in these compounds is most likely because of interactions between the octabedral chains and the chains of REOn polyhedra. The new compounds are closely related to the known yttrium transition metal sulfates.

Magnetic Behavior of Some Rare-Earth Transition-Metal Perovskite Oxide Systems

Magnetic properties were investigated for the rare-earth 3d-transition metal oxides with the perovskite structure. Intriguing magnetic phenomena were reviewed for a few systems:magnetization peak effect in the titanates, magnetization reversal in the chromites and metallic ferromagnetism in the cobaltites. The results suggest an important role of the rare-earth ions for the magnetic properties of such complex oxides.

Effect of Rare Earths-Treated Glass Fiber on Impact Wear-Resistance of Metal-Plastic Multilayer Composites

The friction and wear properties under impact load and dry friction conditions of metal-plastic multilayer composites filled with glass fiber, treated with rare earth elements, were investigated. The worn surfaces were observed and analyzed by scanning electron microscopy (SEM). It shows that applying rare earth elements surface modifier to treat the glass fiber surface can enhance the interfacial adhesion between the glass fiber and polytetrafluoroethylene (PTFE), as well as promote the interface properties of the composites. This helps to form a uniformly distributed and high adhesive transfer film on the counterface and abate the friction between the composite and the counterface. As a result, the wear of composite is greatly reduced. The composite exhibits excellent friction properties and impact wear-resistance.

Effects of rare-earth elements on the glass-forming ability and mechanical properties of Cu_(46)Zr_(47-x)Al_7M_x(M = Ce,Pr,Tb,and Gd) bulk metallic glasses

Cu46Zr47-xA17Mx （M = Ce, Pr, Tb, and Gd） bulk metallic glassy （BMG） alloys were prepared by copper-mold vacuum suction casting. The effects of rare-earth elements on the glass-forming ability （GFA）, thermal stability, and mechanical properties of Cu46Zr47-xA17Mx were investigated. The GFA of Cu46Zr47-xA17Mx （M = Ce, Pr） alloys is dependent on the content of Ce and Pr, and the optimal content is 4 at.%. Cu46Zr47-xA17Thx（X = 2, 4, and 5） amorphous alloys with a diameter of 5 mm can be prepared. The GFA of Cu46Zr47-xA17Gdx（x = 2, 4, and 5） increases with increasing Gd. Tx and Tp of all decrease. Tg is dependent on the rare-earth element and its content. ATx for most of these alloys decreases except the Cu46Zra2Al7Gd5 alloy. The activation energies △Eg, △Ex, and △Ep for the Cu46Zr42A17Gd5 BMG alloy with Kissinger equations are 340.7, 211.3, and 211.3 kJ/mol, respectively. These values with Ozawa equations are 334.8, 210.3, and 210.3 kJ/mol, respec- tively. The Cu46Zr45Al7Tb2 alloy presents the highest microhardness, Hv 590, while the Cu46Zr43A17Pr4 alloy presents the least, Hv 479. The compressive strength （at.f.） of the Cu46Zra3A17Gd4 BMG alloy is higher than that of the Cu46Zr43Al7Tb4 BMG alloy.

Rare Earth Application in Sealing Anodized Al-Based Metal Matrix Composites

A new method for corrosion protection of Al-based metal matrix composites (MMC) was developed using two-step process, which involves anodizing in H2SO4 solution and sealing in rare earth solution. Corrosion resistance of the treated surface was evaluated with polarization curves. The results showed that the effect of the protection using rare earth sealing is equivalent to that using chromate sealing for A16061/SiCp. The rare earth metal salt can be an alternative to the toxic chromate for sealing anodized Al MMC.

Analysis of Different Rare Metals, Rare Earth Elements, and other Common Metals in Groundwater of South West Bank/Palestine by ICP/MS-Data and Health Aspects

Ground water samples are collected from south West Bank/Palestine and analyzed for different rare elements (Rb, Zr, U, P, Ti, V), rare earth elements (La, Ce, and Nd), and other common trace metals (Li, Na, Mg, Ca, Sr, Ba, K, Bi) that most of them usually have no maximum acceptable limits as either they are considered not to be toxic to human health or there is no sufficient data about their toxicity to human health. This study was conducted to determine the water quality of ground water which is used for drinking in the study area. Water samples from ten groundwater wells were obtained in three different dates of the year (November 2012, March 2013, and April 2013). Three water samples were obtained from each well for each sampling date;so a total of 90 water samples were collected from the ten wells. The results obtained from this study suggest a possible risk to the population of the study area given the high concentration of some metals that have no maximum allowed concentration, and the fact that for many people in the study area, ground water is a main source of their water supply.

Influence of oxidant KMnO_4 on film-forming process of rare earth metal conversion coating on LY12 aluminum alloy

A Cu/Al galvanic couple was established to study the influence of the oxidantKMnO_4 on the film-forming process of rare earth metal (REM) conversion coating on LY12 aluminumalloy. It is found that the galvanic couple simulative experiment accords with the actual immersion,and it can be substantially used to simulate the behavior of LY12 aluminum alloy in thefilm-forming process. It is showed that the formation of the coating is quickened in CeCl_3 solutioncontaining KMnO_4 compared with that not containing KMnO_4. XPS results reveal that the coatingformed on cathode is composed of oxide or hydroxide of Ce and Mn, so the mechanism of formation ofREM conversion coating changes when KMnO4 is added.