Dynamic Response Impact of Vehicle Braking on Simply Supported Beam Bridges with Corrugated Steel Webs Based on Vehicle-Bridge Coupled Vibration Analysis

A novel approach for analyzing coupled vibrations between vehicles and bridges is presented,taking into account spatiotemporal effects and mechanical phenomena resulting fromvehicle braking.Efficient modeling and solution of bridge vibrations induced by vehicle deceleration are realized using this method.The method’s validity and reliability are substantiated through numerical examples.A simply supported beam bridge with a corrugated steel web is taken as an example and the effects of parameters such as the initial vehicle speed,braking acceleration,braking location,and road surface roughness on the mid-span displacement and impact factor of the bridge are analyzed.The results show that vehicle braking significantly amplifies mid-span displacement and impact factor responses in comparison to uniform vehicular motion across the bridge.Notably,the influence of wheelto-bridge friction forces is of particular significance and cannot be overlooked.When the vehicle initiates braking near the middle of the span,both the mid-span displacement and impact factor of the bridge exhibit substantial increases,further escalating with higher braking acceleration.Under favorable road surface conditions,the midspan displacement and the impact factor during vehicle braking may exceed the design values stipulated by codes.It is important to note that road surface roughness exerts a more pronounced effect on the impact factor of the bridge in comparison to the effects of vehicle braking.

Prediction of lime utilization ratio of dephosphorization in BOF steelmaking based on online sequential extreme learning machine with forgetting mechanism

The machine learning models of multiple linear regression(MLR),support vector regression(SVR),and extreme learning ma-chine(ELM)and the proposed ELM models of online sequential ELM(OS-ELM)and OS-ELM with forgetting mechanism(FOS-ELM)are applied in the prediction of the lime utilization ratio of dephosphorization in the basic oxygen furnace steelmaking process.The ELM model exhibites the best performance compared with the models of MLR and SVR.OS-ELM and FOS-ELM are applied for sequential learning and model updating.The optimal number of samples in validity term of the FOS-ELM model is determined to be 1500,with the smallest population mean absolute relative error(MARE)value of 0.058226 for the population.The variable importance analysis reveals lime weight,initial P content,and hot metal weight as the most important variables for the lime utilization ratio.The lime utilization ratio increases with the decrease in lime weight and the increases in the initial P content and hot metal weight.A prediction system based on FOS-ELM is applied in actual industrial production for one month.The hit ratios of the predicted lime utilization ratio in the error ranges of±1%,±3%,and±5%are 61.16%,90.63%,and 94.11%,respectively.The coefficient of determination,MARE,and root mean square error are 0.8670,0.06823,and 1.4265,respectively.The system exhibits desirable performance for applications in actual industrial pro-duction.

Operation and Management of Electrical Equipment in Iron and Steel Enterprises

How to ensure the reliable operation of the complex and huge electrical system composed of a large number of electrical equipment in iron and steel enterprises?Combined with working experience,the author introduces four main factors affecting the normal operation of equipment,analyzes five main problems existing in the operation and management of electrical equipment,and puts forward corresponding improvement measures,so as to improve the management level of electrical equipment in iron and steel enterprises.

Exploration and Practice of Nitrogen Addition Process for LF Refining Ladle Bottom Blowing Nitrogen Steel Liquid

This article discusses and analyzes the law of nitrogen increase in liquid steel and the main factors affect-ing the nitrogen increasing of molten steel,through the way of adding nitrogen to molten steel by bottom blowing nitrogen gas in LF refining process.It is considered that the main factors affecting the nitrogen increasing instability of molten steel are the initial temperature of LF refining,nitrogen relative element,surface active elements[O]and[S]of steel liquid,and bottom blowing rate of ladle.The large-scale production practice shows that T[O]not more than 50×10-6 and[S]is not more than 0.020 in LF refining at the initial temperature of not less than 1570.The liquid steel nitrogen enrichment test is carried out by ladle bottom blowing nitrogen gas after 20 min of refining,the flow rate is set as(6.0~7.0)NL/min per ton,and it is turned to 2 NL/min at 6 min before the end of refining,the nitrogen increasing rate of liquid steel is basically stable at(5~6)×10-6 per minute.

Exploration and Application Practice of Energy Conservation Theory and Method in Steel Manufacturing Process System

This article briefly discusses the theoretical basis and overall goals of energy conservation in the steel manufacturing process system.It is proposed that in the process of implementing system energy conservation,it is necessary to fully recognize and utilize the characteristics and functional advantages of the steel manufacturing process,pay more attention to energy quality,firmly grasp the overall goal of system optimization,focus on the integrated optimization of gas,steam,and waste heat systems,and propose the idea of constructing a"steel chemi-cal gas electricity heating cooling multi generation system".Based on practice,the main principles,models,and effects of implementing systematic energy conservation in steel enterprises have been proposed.

基于改进Ratio统计量的重尾AR(p)时间序列均值变点检验

文章提出两个改进的Ratio统计量来研究重尾AR(p)时间序列均值变点检验问题,在原假设下推导了统计量的渐近分布,且在备择假设下证明了其一致性。由于重尾指数未知且难以估计,因此结合Wild Bootstrap重抽样方法来确定渐近分布的临界值;在均值变点存在的情形下,给出了变点位置的一致估计量。数值模拟结果表明:统计量的临界值均不受重尾指数和自回归系数的影响,其经验水平和经验势均取得满意的效果;尤其在原假设下,积分型Ratio统计量的经验水平表现出更好的稳健性,而在备择假设下,最值型Ratio统计量则具备更好的显著性。最后,基于一组股票数据,从实际应用角度进一步阐明所提方法的有效性和可行性。

Abandonment and Recovery Operation of Steel Lazy-Wave Riser in Deepwater by Controlled Vessel and Cable Velocity Rate

Evaluation of abandonment and recovery operation of steel lazy-wave riser in deepwater is presented in this paper.The calculation procedure includes two single continuous SLWR and cable segments, which are coupled together to form the overall mathematical model. Then the equilibrium equations of SLWR and cable are established based on minimum total potential energy principle. The coupled equations are discretized by the finite difference method and solved by Newton-Raphson technique in an iterative manner. The present method is validated by well-established commercial code OrcaFlex. Recovery methods by considering different ratios of vessel’s moving velocity to cable’s recovery velocity are evaluated to optimize the abandonment and recovery operation. In order to keep the tension more stable during the recovery process, the rate ratio before leaving the seabed is increased, and the rate ratio after leaving the seabed is reduced.

Research on the Low-carbon Cementitious Materials:Effect of Triisopropanolamine on the Hydration of Phosphorous Slag and Steel Slag

Cement,phosphorous slag(PS),and steel slag(SS)were used to prepare low-carbon cementitious materials,and triisopropanolamine(TIPA)was used to improve the mechanical properties by controlling the hydration process.The experimental results show that,by using 0.06%TIPA,the compressive strength of cement containing 60%PS or 60%SS could be enhanced by 12%or 18%at 28 d.The presence of TIPA significantly affected the hydration process of PS and SS in cement.In the early stage,TIPA accelerated the dissolution of Al in PS,and the formation of carboaluminate hydrate was facilitated,which could induce the hydration;TIPA promoted the dissolution of Fe in SS,and the formation of Fe-monocarbonate,which was precipitated on the surface of SS,resulting in the postponement of hydration,especially for the high SS content.In the later stage,under the continuous solubilization effect of TIPA,the hydration of PS and SS could refine the pore structure.It was noted that compared with portland cement,the carbon emissions of cement-PS-TIPA and cement-SS-TIPA was reduced by 52%and 49%,respectively.

Preparation of High Activity Admixture from Steel Slag,Phosphate Slag and Limestone Powder

The problem of low disposal and utilization rate of bulk industrial solid waste needs to be solved.In this paper,a high-activity admixture composed of steel slag-phosphate slag-limestone powder was proposed for most of the solid waste with low activity and a negative impact on concrete workability,combining the characteristics of each solid waste.The paper demonstrates the feasibility and explains the principle of the composite system in terms of water requirement of standard consistency,setting time,workability,and mechanical properties,combined with the composition of the phases,hydration temperature,and microscopic morphology.The results showed that the steel slag:phosphate slag:limestone=5:2:3 gave the highest activity of the composite system,over 92%.Besides,the composite system had no significant effect on water demand and setting time compared to cement,and it could significantly increase the 7 and 28 d activity of the system.The composite system delayed the exothermic hydration of the cement and reduced the exothermic heat but had no effect on the hydration products.Therefore,the research in this paper dramatically improved the solid waste dissipation in concrete,reduced the amount of cement in concrete and positively responded to the national slogan of carbon neutral and peaking.

Experimental and numerical study on the influence of shaped charge liner cavity filing on jet penetration characteristics in steel targets

Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifications consisted in removing the frontal part of the grenade(fuse, ballistic cap and conductive cone) and introducing of the liner cavity filling made of polyacetal copolymer POM-C. The filings in the form of solid cones with three different heights(33%, 66% and 100% of H-the height of original PG-7VM liner) were placed inside of the hollow cone shaped charge liner. As opposed to the vast majority of previously published works(in which warhead optimization studies were focused on increasing of the depth of penetration in rolled homogeneous armor steel) the main aim of the presented modifications was to maximize the damage ratio(diameters of craters, inlet and outlet holes) of target perforated by shaped charge jet at the cost of the loss of part of the jet penetration capability. According to the best knowledge of the authors such approach to the use of the old PG-7VM warheads has not been analyzed so far. Taking into consideration high stock levels of PG-7VM warheads, and the fact that they are continuously being replaced by more efficient and more sophisticated high-explosive anti-tank warheads, it seems reasonable to look for alternate applications of the warheads withdrawn from the service. Thanks to the introduction of proposed modifications the warheads could be used by special forces or other assault units as directional mines or statically detonated cutting shaped charges as well as by combat engineers as universal charges used in various types of engineering or sapper works. The research included experimental penetration tests and their numerical reproduction in the LS-Dyna software with the simulation methodology defined and validated in previous works of the authors.Small differences(average error = 10-20%) were identified between the experimental and numerical results(dimensions of craters made in steel targets were compared) what confirmed the reliability of the modelling methodology and enabled its use for further optimization of the shapes of fillings. Within the analyzed variants of warheads modifications maximum diameters of penetration craters were obtained for the filling of the height of h = 2/3H. The diameters of holes in individual steel plates were increased by 164%, 70%, 65%(for the first, second and third plate, respectively) in relation to the variant without filling. The results of the study indicated that with the use of different materials of fillings and their various heights it is possible to control the shape of penetration craters pierced in the steel targets.

Dynamic Properties of Steel Catenary Riser near Touchdown Point Under Coplanar Vessel Heave and Vortex Induced Vibration

The present study establishes a simple numerical model for the coupled response of a steel catenary riser(SCR) subjected to coplanar vessel motion and vortex-induced vibration(VIV). Owing to the large deflection of the SCR, the geometric nonlinearity is considered in this model. The hydrodynamic force comprises the excitation force and hydrodynamic damping, where the excitation force that only exists when the non-dimensional frequency is located in the lock-in range, is associated with the VIV. The hydrodynamic force model is validated based on the published VIV test data.As for the seabed resistance at the touchdown zone(TDZ), integrated with an initial seabed trench, the hysteretic feature is modeled. Based on the model, the study emphasizes on the coupled response characteristics near the touchdown point(TDP) induced by coplanar vessel heave and VIV, and analyzes the sensitivity of the coupled response to the heaving amplitude and frequency. It is found that with the increase of the heave amplitude and frequency, the VIV can be obviously mitigated, but the heave-related response in the coupled analysis seems to be close to that in the heave-only simulation. Finally, the fatigue damage near TDP is parametrically investigated based on the separate analysis and the coupled analysis. The results demonstrate that the coupled effect plays a significant role in the fatigue assessment near TDP. Besides, the proportion of the coupled effect accounting for the total fatigue damage decreases with the increasing seabed stiffness, while increases with the increasing seabed trench depth.

Development and prospects of molten steel deoxidation in steelmaking process

In the long traditional process of steelmaking,excess oxygen is blown into the converter,and alloying elements are used for deoxidation.This inevitably results in excessive deoxidation of products remaining within the steel liquid,affecting the cleanliness of the steel.With the increasing requirements for steel performance,reducing the oxygen content in the steel liquid and ensuring its high cleanliness is necessary.After more than a hundred years of development,the total oxygen content in steel has been reduced from approximately 100×10^(-6)to approximately 10×10^(-6),and it can be controlled below 5×10^(-6)in some steel grades.A relatively stable and mature deoxidation technology has been formed,but further reducing the oxygen content in steel is no longer significant for improving steel quality.Our research team developed a deoxidation technology for bearing steel by optimizing the entire conventional process.The technology combines silicon–manganese predeoxidation,ladle furnace diffusion deoxidation,and vacuum final deoxidation.We successfully conducted industrial experiments and produced interstitial-free steel with natural decarbonization predeoxidation.Non-aluminum deoxidation was found to control the oxygen content in bearing steel to between 4×10^(-6) and 8×10^(-6),altering the type of inclusions,eliminating large particle Ds-type inclusions,improving the flowability of the steel liquid,and deriving a higher fatigue life.The natural decarbonization predeoxidation of interstitial-free steel reduced aluminum consumption and production costs and significantly improved the quality of cast billets.

Systemic immune-inflammation index,neutrophilto-lymphocyte ratio,and platelet-to-lymphocyte ratio in patients with type 2 diabetes at different stages of diabetic retinopathy

AIM:To investigate systemic immune-inflammation index(SII),neutrophil-to-lymphocyte ratio(NLR),and plateletto-lymphocyte ratio(PLR)levels in patients with type 2 diabetes at different stages of diabetic retinopathy(DR).METHODS:This retrospective study included 141 patients with type 2 diabetes mellitus(DM):45 without diabetic retinopathy(NDR),47 with non-proliferative diabetic retinopathy(NPDR),and 49 with proliferative diabetic retinopathy(PDR).Complete blood counts were obtained,and NLR,PLR,and SII were calculated.The study analysed the ability of inflammatory markers to predict DR using receiver operating characteristic(ROC)curves.The relationships between DR stages and SII,PLR,and NLP were assessed using multivariate logistic regression.RESULTS:The average NLR,PLR,and SII were higher in the PDR group than in the NPDR group(P=0.011,0.043,0.009,respectively);higher in the NPDR group than in the NDR group(P<0.001 for all);and higher in the PDR group than in the NDR group(P<0.001 for all).In the ROC curve analysis,the NLR,PLR,and SII were significant predictors of DR(P<0.001 for all).The highest area under the curve(AUC)was for the PLR(0.929 for PLR,0.925 for SII,and 0.821 for NLR).Multivariate regression analysis indicated that NLR,PLR,and SII were statistically significantly positive and independent predictors for the DR stages in patients with DM[odds ratio(OR)=1.122,95%confidence interval(CI):0.200–2.043,P<0.05;OR=0.038,95%CI:0.018–0.058,P<0.05;OR=0.007,95%CI:0.001–0.01,P<0.05,respectively).CONCLUSION:The NLR,PLR,and SII may be used as predictors of DR.

Predictive Ability of Hypertriglyceridemic Waist,Hypertriglyceridemic Waist-to-Height Ratio,and Waist-to-Hip Ratio for Cardiometabolic Risk Factors Clustering Screening among Chinese Children and Adolescents

Objective Hypertriglyceridemic waist(HW),hypertriglyceridemic waist-to-height ratio(HWHtR),and waist-to-hip ratio(WHR)have been shown to be indicators of cardiometabolic risk factors.However,it is not clear which indicator is more suitable for children and adolescents.We aimed to investigate the relationship between HW,HWHtR,WHR,and cardiovascular risk factors clustering to determine the best screening tools for cardiometabolic risk in children and adolescents.Methods This was a national cross-sectional study.Anthropometric and biochemical variables were assessed in approximately 70,000 participants aged 6–18 years from seven provinces in China.Demographics,physical activity,dietary intake,and family history of chronic diseases were obtained through questionnaires.ANOVA,χ2 and logistic regression analysis was conducted.Results A significant sex difference was observed for HWHtR and WHR,but not for HW phenotype.The risk of cardiometabolic health risk factor clustering with HW phenotype or the HWHtR phenotype was significantly higher than that with the non-HW or non-HWHtR phenotypes among children and adolescents(HW:OR=12.22,95%CI:9.54-15.67;HWHtR:OR=9.70,95%CI:6.93-13.58).Compared with the HW and HWHtR phenotypes,the association between risk of cardiometabolic health risk factors(CHRF)clustering and high WHR was much weaker and not significant(WHR:OR=1.14,95%CI:0.97-1.34).Conclusion Compared with HWHtR and WHR,the HW phenotype is a more convenient indicator with higher applicability to screen children and adolescents for cardiovascular risk factors.

Neutrophil-to-lymphocyte ratio and platelet-to-lymphocyte ratio:Markers predicting immune-checkpoint inhibitor efficacy and immune-related adverse events

We conducted a comprehensive review of existing prediction models pertaining to the efficacy of immune-checkpoint inhibitor(ICI)and the occurrence of immune-related adverse events(irAEs).The predictive potential of neutrophil-to-lymphocyte ratio(NLR)and platelet-to-lymphocyte ratio(PLR)in determining ICI effectiveness has been extensively investigated,while limited research has been conducted on predicting irAEs.Furthermore,the combined model incor-porating NLR and PLR,either with each other or in conjunction with additional markers such as carcinoembryonic antigen,exhibits superior predictive capabilities compared to individual markers alone.NLR and PLR are promising markers for clinical applications.Forthcoming models ought to incorporate established efficacious models and newly identified ones,thereby constituting a multifactor composite model.Furthermore,efforts should be made to explore effective clinical application approaches that enhance the predictive accuracy and efficiency.

Recent progress in visualization and digitization of coherent transformation structures and application in high-strength steel

High-strength steels are mainly composed of medium-or low-temperature microstructures,such as bainite or martensite,with coherent transformation characteristics.This type of microstructure has a high density of dislocations and fine crystallographic structural units,which ease the coordinated matching of high strength,toughness,and plasticity.Meanwhile,given its excellent welding perform-ance,high-strength steel has been widely used in major engineering constructions,such as pipelines,ships,and bridges.However,visual-ization and digitization of the effective units of these coherent transformation structures using traditional methods(optical microscopy and scanning electron microscopy)is difficult due to their complex morphology.Moreover,the establishment of quantitative relationships with macroscopic mechanical properties and key process parameters presents additional difficulty.This article reviews the latest progress in microstructural visualization and digitization of high-strength steel,with a focus on the application of crystallographic methods in the development of high-strength steel plates and welding.We obtained the crystallographic data(Euler angle)of the transformed microstruc-tures through electron back-scattering diffraction and combined them with the calculation of inverse transformation from bainite or martensite to austenite to determine the reconstruction of high-temperature parent austenite and orientation relationship(OR)during con-tinuous cooling transformation.Furthermore,visualization of crystallographic packets,blocks,and variants based on actual OR and digit-ization of various grain boundaries can be effectively completed to establish quantitative relationships with alloy composition and key process parameters,thereby providing reverse design guidance for the development of high-strength steel.

Mechanical Behavior and Microstructure Evolution during Tensile Deformation of Twinning Induced Plasticity Steel Processed by Warm Forgings

The mechanical behavior and microstructural evolution of an Fe-30Mn-3Al-3Si twinninginduced plasticity(TWIP)steel processed using warm forging was investigated.It is found that steel processed via warm forging improves comprehensive mechanical properties compared to the TWIP steel processed via cold rolling,with a high tensile strength(R_(m))of 793 MPa,a yield strength(R_(P))of 682 MPa,an extremely large R_(P)/R_(m)ratio as high as 0.86 as well as an excellent elongation rate of 46.8%.The microstructure observation demonstrates that steel processed by warm forging consists of large and elongated grains together with fine,equiaxed grains.Complicated micro-defect configurations were also observed within the steel,including dense dislocation networks and a few coarse deformation twins.As the plastic deformation proceeds,the densities of dislocations and deformation twins significantly increase.Moreover,a great number of slip lines could be observed in the elongated grains.These findings reveal that a much more dramatic interaction between microstructural defect and dislocations glide takes place in the forging sample,wherein the fine and equiaxed grains propagated dislocations more rapidly,together with initial defect configurations,are responsible for enhanced strength properties.Meanwhile,larger,elongated grains with more prevalently activated deformation twins result in high plasticity.

Corrosion Test of the Steel Plate in a WJ-8 Fastener for High Speed Rail

It was found that the steel plate in the composite plate in the WJ-8 fastener used in high speed rail is rusty. The objective of this study is to test the zinc coating of the steel plate. A literature review was conducted to identify the zinc coating techniques, and the companies that can provide different coating service was identified. A salt fog chamber was built that was in compliance with the ANSI B117 code, and the steel plates that were coated by the identified companies were tested using the salt fog chamber. The results indicated that the coating technique that had the best performance in preventing corrosion was the Greenkote plates with passivation. The galvanized option had the roughest coating layer, and it was the most reactive in the salt water solution. This makes it non-ideal for the dynamic rail environment because the increased friction of the plate could damage the supports, especially during extreme temperatures that would cause the rail to expand or contract. Greenkote with Phosphate and ArmorGalv also provided increased corrosion prevention with a smooth, strong finish, but it had more rust on the surface area than the Greenkote with ELU passivation. The ArmorGalv sample had more rust on the surface area than the Greenkote samples. This may not be a weakness in the ArmorGalv process;rather, it likely was the result of this particular sample not having the added protection of a colored coating.

Prognostic role of platelet-to-lymphocyte ratio and neutrophil-to-lymphocyte ratio in patients with non-metastatic and metastatic prostate cancer:A meta-analysis and systematic review

Objective: To analyze data available in the literature regarding a possible prognostic value of the platelet-to-lymphocyte ratio (PLR) and neutrophil-to-lymphocyte ratio (NLR) in prostate cancer (PCa) patients stratified in non-metastatic and metastatic diseases.Methods: A literature search process was performed following the Preferred Reporting Items for Systematic reviews and Meta-Analyses guidelines. In our meta-analysis, the pooled event rate estimated and the pooled hazard ratio were calculated using a random effect model.Results: Forty-two articles were selected for our analysis. The pooled risk difference for non-organ confined PCa between high and low NLR cases was 0.06 (95% confidence interval [CI]: −0.03-0.15) and between high and low PLR cases increased to 0.30 (95% CI: 0.16-0.43). In non-metastatic PCa cases, the pooled hazard ratio for overall mortality between high and low NLR was 1.33 (95% CI: 0.78-1.88) and between high and low PLR was 1.47 (95% CI: 0.91-2.03), whereas in metastatic PCa cases, between high and low NLR was 1.79 (95% CI: 1.44-2.13) and between high and low PLR was 1.05 (95% CI: 0.87-1.24).Conclusion: The prognostic values of NLR and PLR in terms of PCa characteristics and responses after treatment show a high level of heterogeneity of results among studies. These two ratios can represent the inflammatory and immunity status of the patient related to several conditions. A higher predictive value is related to a high NLR in terms of risk for overall mortality in metastatic PCa cases under systemic treatments.

Optimal scheduling of a township integrated-energy system using the adjustable heat-electricity ratio model

With the expansion and implementation of rural revitalization strategies,there is a constant need for new energy sources for the construction of new townships.Consequently,integrated energy systems with the interconnection and interaction of multiple energy sources are developing rapidly.Biomass energy,a renewable green energy source with low pollution and wide distribution,has significant application potential in integrated energy systems.Considering the application of biomass energy in townships,this study established an integrated biomass energy system and proposed a model to optimize its operation.Lowest economic cost and highest clean energy utilization rate were considered as the objective functions.In addition,a plan was suggested to adjust the heat-electricity ratio based on the characteristics of the combined heat and power of the biomass.Finally,a simulation analysis conducted for a town in China was discussed,demonstrating that the construction of a township integrated-energy system and the use of biomass can significantly reduce operating costs and improve the energy utilization rate.Moreover,by adjusting the heat-electricity ratio,the economic cost was further reduced by 6.70%,whereas the clean energy utilization rate was increased by 5.14%.