Influence of yield-to-tensile strength ratio(Y/T) on failure assessment of defect-free and corroded X70 steel pipeline

The effect of yield-to-tensile strength ratio(Y/T) on failure pressure of X70 pipeline without and with corrosion defects was investigated.The stress-strain response of materials was characterized by a power-law hardening curve.Two formulas to estimate the strain hardening exponent n for a special Y/T were obtained by least squared regression method and the influence of Y/T on n was analyzed.As an application of n-Y/T expression,the analytical solutions of burst pressure for X70 pipeline without and with corrosion defects were also obtained.The results indicate that the burst pressure of defect-free X70 pipe without corrosion defects is a function of the Y/T,pipe geometry t0/D0 and engineering tensile strength,and increases as Y/T or t0/D0 increases; whilst the burst pressure of corroded X70 pipe decreases with the increase of defect depths,d/t.Comparisons indicate that the present analytical solutions closely match available experimental and numerical data.

Effect of natural and synthetic fibers reinforcement on California bearing ratio and tensile strength of clay

Use of environmentally friendly approaches with the purpose of strengthening soil layers along with finding correlations between the mechanical characteristics of fiber-reinforced soils such as indirect tensile strength(ITS)and California bearing ratio(CBR)and as well as the evaluation of shear strength parameters obtained from the triaxial test would be very effective at geotechnical construction sites.This research was aimed at investigating the influence of natural fibers as sustainable ones including basalt(BS)and bagasse(BG)as well as synthetic polyester(PET)fibers on the strength behavior of clayey soil.To this end,the effects of various fiber contents(0.5%,1%and 2%)and lengths(2.5 mm,5 mm and 7.5 mm)were experimentally evaluated.By conducting ITS and CBR tests,it was found that increasing fiber content and length had a significant influence on CBR and ITS values.Moreover,2%of 7.5 mm-long fibers led to the largest values of CBR and ITS.The CBR values of soil reinforced with PET,BS,and BG fibers were determined as 19.17%,15.43%and 13.16%,respectively.The ITS values of specimens reinforced with PET,BS,and BG fibers were reported as 48.57 kPa,60.7 kPa and 47.48 kPa,respectively.The results of the triaxial compression test revealed that with the addition of BS fibers,the internal friction angle increased by about 100%,and with the addition of PET fibers,the cohesion increased by about 70%.Moreover,scanning electron microscope(SEM)analysis was employed to confirm the findings.The relationship between CBR and ITS values,obtained via statistical analysis and used for the optimum design of road pavement layers,demonstrated that these parameters had high correlation coefficients.The outcomes of multiple linear regression and sensitivity analysis also confirmed that the fiber content had a greater effect on CBR and ITS values than fiber length.

Distribution and tensile strength of Hornbeam （Carpinus betulus） roots growing on slopes of Caspian Forests, Iran

Biomechanical characteristics of the root system of hornbeam （Carpinus betulus） were assessed by measuring Root Area Ratio （RAR） values and tensile strength of root specimens of eight hornbeam trees growing on hilly terrain of Northern Iran. RAR values of the roots were obtained using profile trenching method at soil depth of the top 0.1 m. In total 123 root specimens were analyzed for tensile strength. Results indicate that in general, RAR decreases with depth, following a power function. The RAR values in up and down slopes have no significant statistical differences. In most cases, the maximum RAR values were located in soil depth of the top 0.1 m, with maximum rooting depth at about 0.75 m. The minimum and maximum RAR values along the profiles were 0.004% and 6.431% for down slope and 0.004% and 3.995% for up slope, respectively. The number of roots in the up and down slope trenches was not significantly different. In the same manner as for RAR, number of roots distributing with depth was satisfactorily approximated a power function. The penetration depths of above 90 percent of the roots were at soil depths of 50 cm and 60 cm for up and down slopes, respectively. Results of Spearman＇s bivariate correlation showed no significant correlation between the RAR value with tree diameter and gradient of slope and number of roots. The mean value of root tensile strength was 31.51 ± 1.05 MPa and root tensile strength decreased with the increase in root diameter, following a power law equation. Using ANCOVA, we found intraspecies variation of tensile strength.

Distribution and tensile strength of Hornbeam(Carpinus betulus) roots growing on slopes of Caspian Forests,Iran

Biomechanical characteristics of the root system of hornbeam(Carpinus betulus) were assessed by measuring Root Area Ratio(RAR) values and tensile strength of root specimens of eight hornbeam trees growing on hilly terrain of Northern Iran.RAR values of the roots were obtained using profile trenching method at soil depth of the top 0.1 m.In total 123 root specimens were analyzed for tensile strength.Results indicate that in general, RAR decreases with depth, following a power function.The RAR values in up and down slopes have no significant statistical differences.In most cases, the maximum RAR values were located in soil depth of the top 0.1 m, with maximum rooting depth at about 0.75 m.The minimum and maximum RAR values along the profiles were 0.004% and 6.431% for down slope and 0.004% and 3.995% for up slope, respectively.The number of roots in the up and down slope trenches was not significantly different.In the same manner as for RAR, number of roots distributing with depth was satisfactorily approximated a power function.The penetration depths of above 90 percent of the roots were at soil depths of 50 cm and 60 cm for up and down slopes, respectively.Results of Spearman's bivariate correlation showed no significant correlation between the RAR value with tree diameter and gradient of slope and number of roots.The mean value of root tensile strength was 31.51 ± 1.05 MPa and root tensile strength decreased with the increase in root diameter, follow-ing a power law equation.Using ANCOVA, we found intraspecies variation of tensile strength.

Effect of low temperature treatment on tensile yield strength of SiC_w/6061 Al alloy composites

The effect of the low temperature treatment at -78 ℃ and -196 ℃ on the microstructure and properties of 18%SiC w/6061(volume fraction) Al alloy composites of as squeeze casting were studied. The results show that, after the low temperature treatment, the dislocation density in matrix increases, and the residual stress of the matrix decreases, as well as the tensile yield strength of the composites improves. The high residual stress exists in the matrix of the composites of as original squeeze casting. The mismatch degree between the matrix and SiC w phases increases during the low temperature treatment. The matrix undergoes the tensile plastic deformation during the cooling procedure. On the contrary, the matrix encountered an elastic unloading procedure during the heating up process from low temperature to room temperature. The increase of dislocation density and the decrease of residual stress in the matrix are the main reason of the improvement for tensile yield strength of the composites.

Machine Learning Design of Aluminum-Lithium Alloys with High Strength

Due to the large unexplored compositional space,long development cycle,and high cost of traditional trial-anderror experiments,designing high strength aluminum-lithium alloys is a great challenge.This work establishes a performance-oriented machine learning design strategy for aluminum-lithium alloys to simplify and shorten the development cycle.The calculation results indicate that radial basis function(RBF)neural networks exhibit better predictive ability than back propagation(BP)neural networks.The RBF neural network predicted tensile and yield strengths with determination coefficients of 0.90 and 0.96,root mean square errors of 30.68 and 25.30,and mean absolute errors of 28.15 and 19.08,respectively.In the validation experiment,the comparison between experimental data and predicted data demonstrated the robustness of the two neural network models.The tensile and yield strengths of Al-2Li-1Cu-3Mg-0.2Zr(wt.%)alloy are 17.8 and 3.5 MPa higher than those of the Al-1Li4.5Cu-0.2Zr(wt.%)alloy,which has the best overall performance,respectively.It demonstrates the reliability of the neural network model in designing high strength aluminum-lithium alloys,which provides a way to improve research and development efficiency.

Effect of Surface Texture on Tensile Shear Strength of 1060Al-PET Welding Joints

Joining metal to plastic can lighten weight of products to reduce energy consumption.However,it is difficult to achieve high-strength welding between metal and plastic.To address this problem,the methods of surface texture pretreatment and laser irradiation welding was proposed to achieve the high-strength connection of metal and plastic.In this study,with different parameters of laser power and texture morphology,1060 Al with surface texture treatment was joined to polyethylene terephthalate(PET)by laser irradiation welding from metal side.Study showed that as the laser power increased,the tensile shear strength of joints increased first,and decreased thereafter.Tensile shear tests demonstrated that the mechanical force of joint was strengthened contributed to mechanical anchorage formed by surface texture.The depth-width ratio of the texture grooves affected the tensile shear process of the joint.According to the result of temperature simulation,the existence of texture grooves reduced the heat transfer efficiency,and the heat dissipation at interface was also impeded in course of laser welding.Finally,the maximum tensile strength of 1060Al-PET joint reached 48.4 MPa,which was close to the strength of PET matrix.The bonding mechanism of the 1060Al-PET joints was composed of mechanical bonding and chemical bonding.This study proposes an effective method to join metal to plastic which achieved high-strength connection between metal and plastic.

Influence of temperature on tensile behavior and deformation mechanism of Re-containing single crystal superalloy

Tensile properties of a Re-containing single crystal superalloy were determined within the temperature range from 20 to 1 100 ℃with a constant strain rate of 1.67 ×10^-4 s^-1.From room temperature to 600 ℃,the yield strength increases slightly with increasing temperature.The yield strength decreases to aminimum at 760 ℃,while a maximum is reached dramatically at 800 ℃.The elongation and area reduction decrease gradually from room temperature to 800 ℃.Above 800 ℃,the yield strength decreases significantly with increasing temperature.The γ＇ phase is sheared by antiphase boundary （APB） below 600 ℃while elongated SSF （superlattice stacking fault） is left in γ＇ as debris.At 760 ℃the γ＇ phase is sheared by a/3 112 superpartial dislocation,which causes decrease of yield strength due to low energy of SSF.Above 800 ℃dislocations overcome γ＇ through by-passing mechanism.

Yield and mechanical properties of veneer from Brachystegia nigerica

In an effort to find suitable wood from natural forest to meet the demand for veneer products, the yield and tensile strength of veneers produced from Brachystegia nigerica were investigated. Two trees of B. nigerica were separately selected from 10 different natural forest zones while two logs were obtained from each tree. The logs were debarked and steamed in a vat prior to rotary peeling and slicing for veneer production. The optimum steam temperature was determined by considering different temperatures： 50℃, 60℃, 70℃, 80℃ and 90℃ for 24 h. Thereafter, optimum steam time was determined at the optimum temperature by considering durations of 24, 48, 72 and 96 h. The average taper of 0.75 mm per 1.0 m length was recorded for B. nigerica, indicating that the logs were reasonably cylindrical; thereby its logs are good for the production of veneer. The yield ranged from 44% to 61% with an average of 52% of the log input. The tensile strength of the veneer was tested perpendicular to grain and both peeled and sliced veneers had the highest tensile strength between 70℃ and 90℃, suggesting that softening of wood polymers, especially lignin, is between 70℃ and 90℃. The optimum temperature and time for veneer production are 70℃ and 48 h, respectively. Commercial production of veneer from B. nigerica is feasible based on the yield and mechanical properties of the obtained veneer, thereby encouraging the expansion of the scope of its utilization.

Influence of recrystallized microstructure on the mechanical properties of cold rolled microalloy high strength steel

Because of the influence of Nb-educts in cold rolled Nb-microalloy high strength steel manufactured by a continuous annealing unit, different quantities of non-recrystallized ferrite exist in the material, which leads to great fluctuation of mechanical behavior of the material. In this study, the relationship between non-recrystallized ferrite and mechanical properties is analyzed, and some factors influencing the formation of non-recrystallized ferrite are also studied.

Tensile and fracture behavior of DZ951 Ni-base superalloy

The tensile and fracture behavior of DZ951 directionally solidified Ni-base superalloy was studied in the temperature range of 20-1 100℃. The fracture mode was examined by scanning electron microscopy. The results show the experimental temperature has no significant effect on the tensile strengths, which are greater than 1 000 MPa from room temperature to 800℃. The yield strength reaches its maximum (970 MPa) at 800℃. When the experimental temperature is higher than 800℃, the tensile and yield strengths decrease evidently and the ductility increases remarkably. The fractograph of fracture surface for the tensile specimen at room temperature shows a dimple-ductile fracture mode. The fractograph from 600 to 800℃shows a slide fracture mode. The fractograph from 900 to 1 100℃exhibits a creep rupture mode with uneven deformation.

Effects of Coiling Temperature on Strength,Yield Ratio and Precipitation Behaviors of Hot Rolled High Strength Microalloyed Steel for Cold Forming

Various hot rolling schedules were applied to a Nb,V,Ti contained HSLA steel.Coiling temperature had crucial effects on not only yield strength,but also yield ratio and precipitation behavior.600Mpa yield strength is achieved when coiled at 450℃,which is 100Mpa higher than those coiled at 570℃.However,the low coiling temperature had adverse effect to increase yield ratio,which increased from 0.78 to 0.88 as coiling temperature dropped from 570℃ to 450℃.High resolution SEM analysis shows that sizes of Nb,V,Ti precipitates are affected by coiling temperature.Coarse (Nb,Ti)(C,N) precipitates up to 5μm are observed at higher coiling temperature and to decrease tensile strength,where high coiling temperature corresponds to low cooling rate.With strong cooling and coiling capacity of Shasteel’s 1450mm width hot rolling mill,these results indicate that strength and formability of the steel can be balanced when coiling temperature has been optimized.Alloying and microalloying costs can be reduced by efficiently utilizing the capacity of rolling mill.Alumina inclusions are found to act as nucleus for Nb,V,Ti precipitates,contributing to coarsening of precipitates.

A STUDY OF THE SPECIMEN SIZE OF STRIP TENSILE TEST FOR NEEDLE-PUNCHED NON-WOVEN GEOTEXTILES

In this paper,the failure features of strip tensile specimen were observed and analysed for need-le-punched non-woven geotextiles.A mechanical model which expresses the relation between thetensile modulus,the strip specimen size,contraction factor and the tensile strength of non-wovenfabric was derived.The theoretical prediction showed that the main factor influencing tensilestrength of non-woven geotextile specimens with different size is the contraction factor of specimenor the specimen aspect ratio(width/length).The larger the aspect ratio,the higher the tensilestrength test value of geotextiles,but the experiments showed that the specimen tensile strength isnot increased with increasing the width of specimen.The reason was discussed and it seemed thatthe deviation could be served as an indication of the degree of imperfectness of the non-wovenstructure.

Effect of Aramid/Carbon Hybrid on the Tensile Properties of Multilayered Biaxial Weft Knitted Fabric Reinforced Composites

The effects of aramid/carbon on tensile properties of multilayered biaxial weft knitted( MBWK) fabric reinforced composites are analyzed by experiments. The tensile tests are inducted by the SHIMADZU AG-250 KNE universal material testing machine and Aramis V6 digital image correlation( DIC) technique.More specifically,the composite samples own four hybrid ratios(Na∶ Nc= 12∶ 0,8 ∶ 4,6 ∶ 6 and 4 ∶ 8). The results showed that the aramid/carbon hybrid MBWK fabric reinforced composites showed nearly linear response until reaching the maximum load and the inserting yarns distribution on the surface of MBWK fabrics reinforced composites had a great influence on the strain pattern distribution. Besides,the tensile strength,the tensile modulus and the elongation at breakage of 0° samples and 90° samples increased with the decreasing of aramid/carbon hybrid ratio. In a word,the changes of tensile strength, tensile modulus and elongation at breakage have a lot to do with the difference of aramid/carbon hybrid ratio.

THE NEW CRITERIA OF ELASTIC AND FATIGUE FAILURE IN THE COMPONENT OF COMPLEX STRESS STATES

In this paper, a total criterion on elastic and fatigue failure in complex stress, that is. octahedral stress strength theory on dynamic and static states on the basis of studying modern and classic strength theories. At the same time, an analysis of an independent and fairly comprehensive theoretical system is set up. It gives generalized failure factor by 36 materials and computative theory of the 11 states of complex stresses on a point, and derives the operator equation on generalized allowable strength and a computative method for a total equation can be applied to dynamic and static states. It is illustrated that the method has a good exactness through computation of eight examples of engineering. Therefore, the author suggests applying it to engineering widely.

氯盐环境下钢筋HRB400的腐蚀行为与力学性能研究

为了给工程安全使用提供借鉴,采用浸泡腐蚀法研究钢筋HRB400在3.5%NaCl溶液中裸露和镶入混凝土2种环境下腐蚀行为及腐蚀后的力学性能,对于钢筋HRB400镶入混凝土这种环境,采用制作钢筋混凝土及模拟混凝土孔隙液2种方法,首先将裸露和镶入混凝土2种情况下的钢筋HRB400浸泡在3.5%(质量分数)NaCl溶液中,并将钢筋HRB400浸泡在饱和氢氧化钙溶液中[加入3.5%(质量分数)NaCl溶液],然后分别计算不同腐蚀时间下各钢筋HRB400相应的失重率、腐蚀率,最后采用MTS试验机测试钢筋HRB400腐蚀后的力学性能。结果显示:随着浸泡腐蚀时间延长,3种环境下的钢筋HRB400平均腐蚀速率逐渐降低,失重率增加,屈服强度、抗拉强度均下降,钢筋HBR400在3.5%NaCl溶液中裸露或镶入混凝土时伸长率随浸泡时间延长而降低,在饱和氢氧化钙(加入3.5%NaCl)中则呈现有升有降趋势。

Weld Joint Efficiency of the Kazakhstani Constructional Steel

In the Republic of Kazakhstan, the regulatory framework in construction based on Eurocodes has been in force since 2015. However, Kazakhstani produced steel has not been studied for compliance with the requirements of Eurocode 1993. This has resulted in limited use of Kazakhstani structural steel in construction. The feasibility of using structural steel in welded joints has been experimentally investigated. To verify the application of such joints in construction, including earthquake engineering, experimental studies of welded joints made of structural steel produced by Arcelor-Mittal in Temirtau have been carried out. In total, 7 types of structural steel of various thicknesses were selected. Five specimens have been used in each series of tests. The Brinell hardness values of the weld joint, yield strength of steel and tensile strength, relative rupture strain were determined. It was found that for all types of structural steel, the quality of weld joints complied with the requirements of Eurocode 1993—a sample rupture appeared along the plates (main body of the metal), not along the weld joints. It has been established that structural steel produced in the Republic of Kazakhstan fully complies with the requirements of Eurocode 1993. The studies on the dependence of Brinell hardness values of weld joint steel on the yield strength, tensile strength and relative rupture strain have been carried out. The correlation dependences between the values of yield strength of steel and tensile strength, relative rupture strain and BH Brinell hardness were studied. The results of work will allow for significantly increasing the use of Kazakhstani structural steel in seismic and conventional areas of the Republic of Kazakhstan.

高强页岩轻骨料混凝土制备及微观结构研究

基于最紧密堆积理论和最小需水量法进行高强页岩轻骨料混凝土配合比设计与制备,研究了水胶比对抗压及劈裂抗拉强度影响,并借助SEM/EDS进行微观测试分析。结果表明:当粗细骨料体积分数比为5.5:4.5时,粗细骨料达到最紧密堆积状态;当硅灰、粉煤灰和水泥质量比为0.8:3.2:6时,需水量最少,粉体材料密实度最佳;依据优化配比所配混凝土的抗压强度和劈裂抗拉强度均随龄期增加而增加;随着水胶比增加,抗压强度和劈裂抗拉强度呈先增后减的趋势,且当水胶比为0.24时达到最大,分别为70.9、5.83MPa;硅灰和粉煤灰特有的形态效应和火山灰效应有效改善了浆体与骨料间界面的密实程度,微观结果显示浆体与骨料界面区域结构致密,陶粒区域为富Si、Al相,浆体一侧为富Ca相。

Cu-4Ag合金微细丝拉拔极限预测模型

采用三室真空冷型竖引连铸设备制备了Cu-4Ag合金铸态杆坯,并利用连续冷拉拔变形得到了不同线径的Cu-4Ag合金微细丝,通过拉拔实验获取了不同线径下材料的屈服强度和抗拉强度;基于线径与强度的关系,构建了微细丝拉拔极限预测模型。结果表明,在拉拔过程中,Cu-4Ag合金微细丝的线径与抗拉强度密切相关,具有明显的尺寸效应;修正后的拉拔极限模型能够较为准确地预测不同线径的Cu-4Ag合金微细丝能够达到的拉拔极限。将拉拔极限模型产出的数据导入MATLAB中,构建了三维曲面模型,可以更为直观地分析材料的拉拔极限。

不同粗骨料取代率下粉煤灰再生混凝土的力学性能研究

为探讨不同再生粗骨料取代率下粉煤灰对再生混凝土力学性能的影响,以及再生混凝土抗折强度与再生粗骨料取代率、水胶比之间的关系,以RC30设计强度等级为基础设计了16组配合比,制作了96块再生混凝土试块,主要进行了再生混凝土的抗压强度试验和抗折强度试验。得出如下结论:随粉煤灰掺量的增加,不同再生粗骨料取代率,抗压强度变化规律有所不同;再生粗骨料取代率为0、30%和40%时,抗压强度随粉煤灰掺量的增加整体呈下降趋势;而当再生粗骨料取代率为50%时,随粉煤灰掺量的增加,抗压强度先减小后增大。粉煤灰掺量大于20%时,天然骨料混凝土的抗压强度急剧下降,而再生骨料混凝土的抗压强度降低幅度均较小,大掺量粉煤灰在再生混凝土中或将有更大的应用空间。通过观察抗折强度试件破坏断面,分析再生混凝土变形破坏特征。粉煤灰的掺入提高了天然骨料混凝土的抗折强度,且掺量为20%强度最高。再生粗骨料取代率为30%时,随粉煤灰掺量变化抗折强度整体呈下降趋势,但下降幅度很小;再生粗骨料取代率为40%和50%时,呈先减后增再减的趋势。天然骨料混凝土的折压比随粉煤灰掺量的增加而提高;再生混凝土折压比随粉煤灰掺量的变化趋势与抗折强度一致,但变化幅度略小。粉煤灰对再生混凝土抗折强度的影响大于抗压强度;再生粗骨料取代率为30%,粉煤灰掺量为10%为较优掺量。提出再生混凝土抗折强度预测式。